SPECIAL REPAIR TO BOUNDARY WALLS AT RESIDENCY OFFICERS MESS AT AF STN GWALIOR

Amount

Excavating over area n exc 1.5m deep and getting out in soft/loose soil Complete all as specified and directed by Engineer-in-Charge.

Plain Cement Concrete Type D2 1:4:8 (using 40 mm graded stone aggregate) in foundations, filling and mass concrete Complete all as specified and directed by Engineer-in-Charge.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work vertical or to batter Complete all as specified and directed by Engineer-in-Charge.

Formwork to faces of walls, retaining walls, abutments, parapets and staircase railing and similar work including attached pillasters, buttresses, etc;for fair finished surfaces Complete all as specified and directed by Engineer-in-Charge.

RCC M25 (20mm graded aggregates) design mix for foundation , including rafts, footings, foundation beams; plinth beams; bases for columns, etc, basement slabs,, under-reamed piles and mass concrete Complete all as specified and directed by Engineer-in-Charge.

RCC M25 (20mm graded aggregates) design mix for Walls, retaining walls, basement walls, ballast walls and the like; any thickness Complete all as specified and directed by Engineer-in-Charge.

M&L for TMT bars10 mm dia and over cut to length bent to shape spirally for hooping,hooking ends and binding with mild steel wire (annealed) not less than 0.5 mm dia or securing clips etc Complete all as specified and directed by Engineer-in-Charge.

Mild steel TMT bars 6 to 8 mm dia., cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips as in stirrups Complete all as specified and directed by Engineer-in-Charge.

ditto as per item No 8 above but 5 mm dia and over.upto and including 10mm dia as in stirrups spacers and binders complete all as specified and directed

M&L for PVC pipe 75mm dia as in weep holes Complete all as specified and directed by Engineer-in-Charge.

M&L for loose filling with aggregate of gauge 40 to 80mm in weep holes etc Complete all as specified and directed by Engineer-in-Charge.

S&F,mild steel work as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc, flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc, running bars, for chain link fencing including embeding in concrete and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed

S&F Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated conforming to Fe-410-W (Gde-E-250) quality-A complete all as specified and as directed. Note : The rates quoted allow for cutting to dead length where required, notching, drilling, fitting, riveting and/or welding or connecting with bolts and nuts (including rivets or bolts and nuts), providing and fitting angle cleats, fish plates, gusset plates etc., also for wedging, plumbing, truing up and fixing complete.

Supply only MS screw, bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut exceeding 5cm and not exceeding 10cm long and dia of bolt etc, complete all as specified and directed

S&F galvanised, 2 strand, steel barbed wire 2.24 mm dia barbed with 2mm dia barbs at 75mm spacing and straining and fixing to any type of standard rail straining bolt, including, typing at crossing with and provision of galvanised mild steel wire, staple or steel pins etc Complete all as specified and directed by Engineer-in-Charge.

S&F Galvanized concertina wire of coil dia 610mm, blade thickness 0.50mm, blade lenth 19mm,wire thickness 2.50 mm and stretch ability up to 8M complete all as specified and as directed.

M&L, two coats of synthetic enamelled paint over a coat of red oxide primer including preparation of new steel/iron surfaces exceeding 10cm width or girth.complete all as specified and directed

M&L preparation of newly plastered surfaces of walls and applying one coat of primer two coats of cement base paint, complete all as specified and directed.

Returning, filling, including spreading, levelling, watering and well ramming in layers not exc 25 cm.Complete all as specified and directed.

Removing excavated materials n.exc 50 M and depositing where directed at a level n exc 1.5 M above the starting point Complete all as specified and directed by Engineer-in-Charge.

M/S NIRMAL SINGH DHANJAL

m/s vikash Engineers

Babatia super works

RADHA MADHAV CONSTRUCTIONS

M/s Ratan Lal Jain and Co.

Akarsha Enterprises

KRISHNA ENTERPRISES

M/s Subhash Construction Co.