Construction of Govt. Women College at village Padha (Assandh) Distt. Karnal (Pdg. EI, Substation and Security Light only).

Amount

1 - E.I Supply and erection of metal clad switches / B.D.Bs with rag bolts on wall or on existing angle iron board / pedestal including bonding to earth and necessary connections . Triple pole switch with neutral link 32 amp. 415 Volts. 31.12(a) (xiv) Cat-B

- Triple pole switch with neutral link 63 amp. 415 Volts. 31.12 (a) (xv) Cat-B

2 - Supply and erection of moulded case circuit breakers on wall or on existing pedestal including bonding to earth and necessary connections. 15 amp.to 60 amp. 415 V ,10 KA 3-phase. 31.12 c (i)

- 100 amp.to 220 amp.415 V,10 KA 3-phase. 31.12 c (ii)

- 250 amp. 415 V , 35 KA 3-phase. 31.12 c (iii)

- 300 amp. to 400 amp. 415 V , 35 KA 3-phase. 31.12 c (iv)

3 - Supply and erection of M.S. angle iron frame duly welded for housing M.S. sheet & main switches etc. on it, fixed on wall by means of suiteble size of rag bolts with cement concrete ,duly painted with three coats of approved paint including one coat of red oxide. Size 40 mm x 40 mm x 6 mm. 31.13(ii)

4 - M.S.Sheet . Supply and erection of 3 mm thick mild steel sheet duly welded on existing M.S. angle iron frame for fixing the main switches etc. as required, duly painted with three coats of approved paint including one coat of red oxide. 31.14 (i)

5 - Supply and erection of sheet steel enclosure 2 pole / 3 pole with earth plug and socket suitable for incorporating single pole / triple pole MCB on wall / on existing pedestal complete with necessary connections etc. S.P.N. enclosure for single pole MCB 20 amp. 31.15 (ii)

6 - Supply and erection of miniature circuit breaker / isolator 240 /415 V in the existing distribution board including making necessary connections. Miniature circuit breakers of 9 KA breaking capacity. SP MCB of 9 KA breaking capacity 6 amp. to 32 amp. 31.17a) (ii)

- TPN MCB of 9 KA breaking capacity 6 amp. to 32 amp. 31.17(a) (ii)

- TPN MCB of 9 KA breaking capacity 40 amp. to 63 amp. 31.17(a) (iii)

7 - Supply and erection of Fittings and Accessories. Call bell 220 / 230 volts A.C. bakelite with double coil. 31.18 (vii)

- Bell push flush type ( without flexible wire ) in existing sheet. 31.18 (ix) (b)

- Bakelite angle / straight button holder large size. 31.18 (xi)

- Switch 5 amp. On existing sheet. 31.18 (xii)

- Wall socket 5 amp. On existing sheet. 31.18 (xiii)

- Erection only of 1x40 watts or 2x40 watts 1220 mm long / 1x20 watts or 2x20 watts ,610 mm long fluorescent tube fitting directly on wall including necessary connections with 0.75 sqmm ( 24 / 0.20 mm ) PVC copper flexible cable for connecting the tube with the adjecent point. 31.18 (xxiv)

- Supply and erection of hexagonal M.S. box 1.60 mm thick having each side 8 cms , 7.5 cms deep top covered with M.S. lid by means of screws including 10 mm dia 30 cm long mild steel rod made into suitable suspension hook and erected in RCC slab for erection of fan , the bottom covered with 3 mm thick bakelite sheet with suitable holes , painting etc. complete with all labour and material required to complete the job. . 31.18 (xxvi)

8 - Erection and carriage of fans.. Erection of ceiling fan complete with necessary earthing of fan and regulator including carriage from local railway station /goods transport /PWD store to the site of work. 31.20 (i)

- Erection of exhaust fan complete with necessary earthing of fan and regulator including carriage from local railway station /goods transport /PWD store to he site of work. 31.20 (iii)

- Making suitable hole in the wall upto 450 mm sweep exhaust fan including finishing the same and fixing of wire mesh duly fixed with Deodar wood frame of section 40 mm x 25 mm thick. 31.20 (v)

- Pdg. and fixing of required size of deodar wood frame of section 50 mm x 32 mm for fixing exhaust fan upto 450 mm sweep. 31.20 (vi)

9 - Supply and erection of pipe for wiring purposes including bends inspection boxes etc. where necessary and painting as required. Heavy guage welded conduit pipe 20 mm dia 1.60 mm thickness flushed. 31.21 (xxi)

- Heavy guage welded conduit pipe 25 mm dia 1.60 mm thickness flushed. 31.21 (xxii)

- Supply and erection of PVC pipe of 6 kg. pressure laid 1 metre below ground level complete including digging refilling of the trench with jointing etc. PVC pipe 120 mm dia. 31.21(xxx) (a)

10 - Earthing Earthing with GI earth pipe 4.5 m long and 40 mm dia with masonry enclosure on the top etc. as required . 31.22(i)

- Extra for using salt and charcoal / coke for pipe earth electrode as required. 31.22(ii)

- Earthing with GI earth plate 600 mm x 600 mm x 6 mm thick including accessories and providing masonry enclosures with cover plate having locking arrangement and watering pipe etc. ( but without charcoal or coke and salt ) complete as equired. 31.22(iii)

- Earthing with tinned copper earth plate 600 mm x 600 mm x 3 mm thick including accessories and providing masonry enclosures with cover plate having locking arrangement and watering pipe etc. ( but without charcoal or coke and salt ) comlete as equired. 31.22(iv)

- Extra for charcoal or coke and salt for G.I. Plate or copper plate earth electrode. 31.22(v)

- Pdg. and fixing 25 mm x 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode as required . 31.22(x)

- Pdg. and fixing 25 mm x 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode as required . 31.22(xi)

- Pdg. and laying earth connections from earth electrode with 4.00 mm dia G.I. wire in 15 mm dia G.I. pipe from earth electrode as required . 31.22(xii)

- Supply and erection of 20 mm x 3 mm thick G.I. tape fixed with suitable G.I. stapples of same size. 31.22(xix)

- Supply and erection of 20 mm x 3 mm thick copper tape fixed with suitable copper staples of same size. 31.22(xx)

11 - Supply and erection of under ground cable ,loose in existing pipe or trenches complete with necessary connections . 50 Sq. mm 3.5 Core Cable . 31.26 (xxvii) Ard.

- 10 Sq. mm 4 Core Cable . 31.26 (xxxix) Ard.

- 16 Sq. mm 4 Core Cable . 31.26 (xI) Ard.

12 - Supply and erection of suitable compression type brass cable glands for underground Cable. 10 Sqmm to 16 Sqmm Cable 2 to 4 Core . 31.28 (ii)

- 25 Sqmm to 50 Sqmm Cable 2 to 4 Core. 31.28 (iii)

13 - Supply and erection of metal clad bus bar chamber made from 1.6 mm thick M.S.sheet fixed with rag bolts on wall or on existing pedestal / angle iron frame including bonding to earth , detatchable top and bottom painting and necessary connections etc.(Copper bars duly tinned ). 100 amp. 4 bars of 55 cm each (cross section 25 mm x 3 mm) chamber over all size 60 cm x 45 cm x 18 cm . 31.31 (a) (ii)

14 - Wiring in 1.5 sq.mm PVC Insulated Copper conductor cable in 1.6 mm thick conduit pipe. Fan Point Medium Point 31.36 (I) (b)

- Long point. (c)

- Light Point Short point 31.36 (II) (a)

- Medium Point (b)

- Long point. (c)

- Twin control light point with 2 way, 5 amp. single pole switch. Long point. 31.36 (III) (c)

- Call bell point including M.S box of size 180 mmX100 mmX 60 mm deep for Call bell. Long point. 31.36 (VI) (c)

- 3 pin 5 amp. plug point including earthing the 3rd. pin etc. Short point 31.36 (VII) (a)

- Medium Point (b)

- Long point. (c)

- 3 pin15 amp. plug point with 4 sq mm PVC insulated Copper conductor cable- including earthing the 3rd. pin etc. Long point. 31.36 (VIII) (c)

15 - Supply and erection of PVC unsheathed copper conductor cable single core 1100 volts grade in pipe of suitable size excluding cost and erection of pipe . Size 1.5 sqmm ( 3/0.81 ) 31.40 (i)

- Size 2.5 sqmm ( 3/1.05 ) 31.40 (ii)

- Size 4 sqmm ( 7/0.85 ) 31.40 (iii)

- Size 6 sqmm ( 7/1.05 ) 31.40 (iv)

- Size 10 sqmm ( 7/1.35 ) 31.40 (v)

16 - Supply and erection of Double door sheet steel enclosure distribution boards suitable for MCB's & ELCB's recessed in wall including bonding to earth complete with all labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-charge of the work. 4-way , TP&N ( Horizontal) (8+12) 31.41 (v)

- 8-way , TP&N ( Horizontal) (8+24) 31.41 (vi)

- 12-way , TP&N ( Horizontal) (8+36) 31.41 (vii)

17 - Supply and erection of PVC pipe ISI marked ( Medium ) recessed in wall / ceiling etc. including the cost of PVC bends , inspection boxes , iron hooks and cement concrete etc. complete in all respect upto the entire satisfaction of Engineer-in-charge of work. 25 mm dia. 31.44 (ii)

18 - Supply & erection of Socket size rotary step type Electronic regulator for A.C. ceiling fan Anchor make Delux model No. 50440 ISI / SSK make PC 561 operated on 120/280 V A.C. Supply complete including cutting of existing Bakelite sheet and making necessary connection etc. up to the entire satisfaction of the Engineer-in-Charge of the Work. 31.55

19 - Supply installation testing and commissioning of wall / free standing floor mounting dust & vermin proof compartmentalized cubical panel made out of 2mm thick CRCA sheet, required hardware, 3mm thick bakelite sheet provided all along the bus bar and cable alley separating switches compartment and supporting suitable channel, dully painted by 2 coat of zinc / Red oxide primer followed by 2 coats of powder coating in grey or required shade after rinsing. The panel having PU / Neoprene rubber gasket of not less than 3mm thickness, separate detachable gland plate MS base channel, hinged door with inter locking arrangement for equipment / switch gear. Transparent acrylic sheet shall be provided in front of bus bar compartment to prevent direct access to bus bar bakelite sheet 3mm thick for separately cable alley to BBC from switch chember. Extended solid copper bars up to cable alleys shall be provided for outgoing connection which shall be paid as extra items. Side walls and cable alley compartments shall be having bolted type doors with detachable extension type structure. The panel will be complete with control wiring (copper) and fuse protection. (only outer area on all sides shall be measured). Size 2100x1750x450mm deep. 31.63

20 - Supplying and fixing of Copper bus bar duly tinned by means of SMC/DMC type insulator high tensile nuts and bolts spring washers fixing to same in existing panel including bending , cutting in required shape and size and insulation with colour coding heat shrinkable PVC insulation Complete in all respect. 31.64

22 - Supply & fixing of rotary handle for on / off operation of existing MCCB in the LT panel including fixing the same in position with all labour and material required to complete the job in all respect. up to 125A MCCB 31.66 (i)

- Above 125A MCCB (ii)

23 - Supply and erection of metal clad bus bar chamber made from 1.6 mm thick M.S.sheet fixed with rag bolts on wall or on existing pedestal / angle iron frame including bonding to earth Copper bars 63 amp. 415volt 4 bars of 325mm each (Cross section 20x3mm) duly tinned over all size of the chember 375mmx295mmx140mm. 31.76

24 - Supply and erection of MS box of size 8'' x 10'' x 4'' (20cmx25cm) and 10cm deep made of 1.6mm thick M.S. sheet covered with 5mm thick bakelite sheet for fixing of 4 Nos. socket and switch of 6 amp. and one No. of multi socket and switch of 15 amp. including fixing of one No. fuses unit and indicator off another make. the M.S. box is recessed in wall including cost of necessaru cement and mixture required to complete the job in all respect upto entire satisfaction of the Engineer-in-charge of work. NS

25 - Electric Substation & Security Light Earth work in excavation in foundations, trenches, etc in all kinds of soil not exceeding 2.0 Mt depth including dressing of bottom and sides of trenches stacking the excavated soil clear from the edge of excavation and subsequent filling around masonry in 15 Cm layers with compaction, including disposal of all supplies soils as directed with in a lead of 30 mts 6.6

26 - Cement concrete 1: 8: 16 with brick ballast 40 mm nominal size in foundation and plinth 10.26

27 - Cement concrete 1:2:4 with stone aggregate 20 mm nominal size foundation and plinth 10.41

28 - First class brick work laid in cement sand mortar 1:6 in foundation and plinth 11.2

29 - Brick edging 6.83 cm wide 11.43 cm deep to plinth protection with 2st class brick including grouting with cement sand mortar 1:4 11.1

30 - 12mm thick cement plaster 1:5 15.6

31 - Supply and erection of moulded case circuit breakers on wall or on existing pedestal including bonding to earth and necessary connections. 15 amp. to 60 amp. 415 V ,10 KA 3-phase. 31.12 c (i)

- 100 amp. to 220 amp.415 V,10 KA 3-phase. 31.12 c (ii)

- 300 amp. to 400 amp. 415 V , 35 KA 3-phase. 31.12 c (iv)

32 - Supply and erection of pipe for wiring purposes including bends inspection boxes etc. where necessary and painting as required. Galvanised iron pipe 65 mm dia on flushed. 31.21 (xiv)

- Supply and erection of PVC pipe of 6 kg. pressure laid 1 metre below ground level complete including digging refilling of the trench with jointing etc. PVC pipe 80 mm dia. 31.21(xxx) (b)

33 - Earthing Earthing with GI earth pipe 4.5 m long and 40 mm dia with masonry enclosure on the top etc. as required . 31.22(i)

- Extra for using salt and charcoal / coke for pipe earth electrode as required. 31.22(ii)

- Earthing with tinned copper earth plate 600 mm x 600 mm x 3 mm thick including accessories and providing masonry enclosures with cover plate having locking arrangement and watering pipe etc. ( but without charcoal or coke and salt ) comlete as equired. 31.22(iv)

- Extra for charcoal or coke and salt for G.I. Plate or copper plate earth electrode. 31.22(v)

- Pdg. and laying earth connections from earth electrode with 4.00 mm dia G.I. wire in 15 mm dia G.I. pipe from earth electrode as required . 31.22(xii)

- Pdg. and fixing 25 mm x 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode as required . 31.22(x)

- Pdg. and fixing 25 mm x 5 mm copper strip on surface or in recess for connections etc. as required with all labour and material. 31.22(xiv)

34 - Supply and erection of under ground cable ,loose in existing pipe or trenches complete with necessary connections. (Make Havells, Polycab, Grandaly) 400 Sq. mm 3.5 Core Cable . 31.26 (xxxv) Ard.

- 16 Sq. mm 4 Core Cable . 31.26 (xI) Ard.

- 25 Sq. mm 4 Core Cable . 31.26 (xIi) Ard.

- 50 Sq. mm 4 Core Cable . 31.26 (xIiii) Ard.

35 - Supply and erection of suitable compression type brass cable glands for underground Cable. 10 Sqmm to 16 Sqmm Cable 2 to 4 Core . 31.28 (ii)

- 25 Sqmm to 50 Sqmm Cable 2 to 4 Core. 31.28 (iii)

- 300 Sq mm to 400 Sqmm Cable 3 to 3.5 Core . 31.28 (vii)

36 - Street Light. Supply and erection of 32 mm dia meter 1.5 metre long bracket ( B-Class ) making an angle of 10 to 15 degree with horizontal plane for mounting street light fitting fixing of GI bracket on wall with 2 Nos. , 32 mm x 3 mm thick MS clamps including the cost of cutting , welding of GI pipe complete with cement sand mixture , bolts and nuts etc. including necessary connections . 31.30 (III) (xv )

- Supply and erection of prestressed cement concrete pole as per IS : 1678-1960. 9 metres long 105 mm x 115 mm at top and 105 mm x 315 mm at bottom with working load of 200 Kg. burried 1.80 m in ground. 31.30 (VI) (ii)

37 - Pedestal .Supply and erection of Godrej Almirah typeM.S.pedestal made of 50 mm x 50 mm x 6 mm angle iron frame with 3.00 mm thick M.S.sheet covering including shutters with suitable hinges and locking arrangement with Godrej type handle including round bars . The top covering should have downward overhang of 75 mm on all sides of pedestal , having two sets of water proof ventilation holes of suitable size on the sides , at top and bottom , each set containing four Nos. holes to discharge the heat produced by the current . The shutters fixed with rubber gasket of superior quality and of suitable size to make it water proof . The pedestal duly painted both inside and outside with two coats of approved paint and primary coat and its legs are embeded upto the entire depth in 1:2:4 cement concrete block , projected 75 mm all around the pedestal and and 200 mm above the ground level including the cost of all labour and material required to complete the job in all respect upto the entire satisfaction of the Engineer-in-charge of the work:- M.S.pedestal of size 1500 mm wide , 1800 mm high ,450 mm deep and bottom totally open , duly embeded in cement concrete block of size 1650 mm x 600 mm x 200 mm above ground level duly plastered with 12 mm thick 1:4 cement plaster , having a base of size 1800 mm x 750 mm x 250 mm below ground level . 31.33 (vi)

38 - Miscellaneous .Supply and erection of caution notice plate in three languages. 31.35 (iii)

- Supply and erection of shock restoration chart in glass frame 31.35 (iv)

39 - Supply installation testing and commissioning of wall / free standing floor mounting dust & vermin proof compartmentalized cubical panel made out of 2mm thick CRCA sheet, required hardware, 3mm thick bakelite sheet provided all along the bus bar and cable alley separating switches compartment and supporting suitable channel, dully painted by 2 coat of zinc / Red oxide primer followed by 2 coats of powder coating in grey or required shade after rinsing. The panel having PU / Neoprene rubber gasket of not less than 3mm thickness, separate detachable gland plate MS base channel, hinged door with inter locking arrangement for equipment / switch gear. Transparent acrylic sheet shall be provided in front of bus bar compartment to prevent direct access to bus bar bakelite sheet 3mm thick for separately cable alley to BBC from switch chember. Extended solid copper bars up to cable alleys shall be provided for outgoing connection which shall be paid as extra items. Side walls and cable alley compartments shall be having bolted type doors with detachable extension type structure. The panel will be complete with control wiring (copper) and fuse protection. (only outer area on all sides shall be measured). 31.63

40 - Supplying and fixing of Copper bus bar duly tinned by means of SMC/DMC type insulator high tensile nuts and bolts spring washers fixing to same in existing panel including bending , cutting in required shape and size and insulation with colour coding heat shrinkable PVC insulation Complete in all respect. 31.64

42 - Supply & fixing of rotary handle for on / off operation of existing MCCB in the LT panel including fixing the same in position with all labour and material required to complete the job in all respect. up to 125A MCCB 31.66 (i)

- Above 125A MCCB (ii)

43 - S/E of mark double walled corrugated (DWC) HDPE pipe laid 1 mtr. below ground level including diging and refilling of earth including cost of suitable size socket / cuppler for HDPE pipe including the cost of labour and material required to complete the job in all respect upto the entire satisfaction of Engineer-incharge of the work HDPE pipe 63 / 50mm outer dia / inner dia. 31.67 (i)

44 - Supply & Erection of Hot Dip Galvanized octagonal pole of 3 mm thickness, with base plate including cost of nut and bolts and all accessories as supplied by the manufacturer including cost of foundation accessories etc. The foundation bolts as per manufacturer design should be hot dipped galvanized pole complete with door locking arrangement. Terminal plate consisting of 2 Nos. 100A. 4 pole natural links including connection etc. with suitable connecting arrangment for 2 no. MCBs / kit kat including cost of R.C.C. 1:1.5:3 for foundation of size 0.7 M. x 0.7 M. x 1.8 M with minimum 8 Nos. 12mm dia longitudinal MS reinforcement rods with rings of 8 mm dia not more than 200mm C.C. for fixing the pole with all labour & material required to complete the job in all respect upto the entire satisfaction of Engineerin-charge of the of the work. 7 Mtr. Long pole with top dia 70mm and botom dia 130mm with base plate of size 220 x 220 x 12mm. 31.68 (i)

45 - S/E of XLPE (E) 11 KV HT aluminum conductor armoured cable ISI mark laid in existing pipe /trenches/surface with all labour and material required to complete the job in all respect upto the entire satisfaction of the Engineer-in-charge of the work. 50 sqmm 3 core XLPE Cable 31.71 ii

46 - Supply and erection of heat shrinkage type end termination jointing kit indoor type of suitable to accommodate 3 core 11 KV XLPE aluminum cable/ ABC cable complete with all the kit contents including earth continuing connection along with 3 nos. crimpling type aluminum lugs of suitable capacity including making joining etc complete in all respect. Suitable for 16 to 50 sqmm 3 core XLPE Cable 31.72 i

47 - Supply and erection of heat shrinkage type end termination jointing kit outdoor type of suitable to accommodate 3 core 11 KV XLPE aluminum cable/ ABC cable complete with all the kit contents including earth continuing connection along with 3 nos. crimpling type aluminum lugs of suitable capacity including making joining etc complete in all respect. Suitable for 16 to 50 sqmm 3 core XLPE Cable 31.73 i

48 - Supply and erection of ACSR conductor (ISI Marked) with accessories including stringing and sagging of conductor of various sizes as well as jointing and binding with insulator at support complete in all respect up to entire satisfaction of Engineer-in-charge of the work. ACSR Cond. 80 Sqmm Otter NS

- ACSR Cond. 50 Sqmm

- ACSR Cond. 20 Sqmm

49 - Supply, stringing and sagging of GSL wire 8 SWG complete in all respect with erection of the same upto the entire satisfaction of the Engineer in Charge of work NS

50 - Supply and erection of MS channel 100x50x6mm including cutting bending to the required shape drilling hole carriage Painting loading unloading complete in all respect upto the entire satisfaction of Engineer-in-charge. NS

51 - Supply and erection of MS angle 50x50x6mm including cutting bending to the required shape drilling hole carriage Painting loading unloading complete in all respect upto the entire satisfaction of Engineer-in-charge. NS

52 - Supply and erection of MS flat 50x6mm including cutting bending to the required shape drilling hole carriage Painting loading unloading complete in all respect upto the entire satisfaction of Engineer-in-charge. NS

53 - Providing and fixing of Nut & Bolt of size as per ISI specification of Engineer-in-charge. NS

54 - Supply and erection of Shackle insulator as per State Electricity Nigam specification upto the entire satisfaction of Engineer-in-Charge. NS

55 - Supply & erection of 11KV GI pin insulator Rashtriya / Jayshree / BHEL make with pin with all labour and material required to the complete the job included the fixing the same on existing channels up to entire satisfaction of the Engineer-in-Charge of the works. NS

56 - Supply of MS D-strip type-I made out of MS flat of size 40x6mm suitable for LT insulator 90x75mm with latest amendments complete in all respect with erection of the same upto the entire satisfaction of the Engineer in Charge of work excluding cost of Nuts & bolts. NS

57 - Supply & erection of 11KV gang operated switch Rashtriya / Jayshree / BHEL make conforming to IS with latest amendment including suitable size of copper blade erection of same on the existing 'H'pole with the help of 3 Nos. channels of size 75mmx40mmx6mm, 1.8M long fixed with suitable size of MS clamp, nuts and bolts including cost of 6 Nos. 11KV insulator with GI pin, RD fuses and painting with 2 coat of approved paint and one coat of red oxide material required to complete the job in all respect up to entire satisfaction of the Engineer-in-Charge of the works. NS

58 - Supply Erection Testing & Commissioning of 11kV indoor HT metering panel indoor / outdoor complete with C.Ts P.Ts Cubical .as per requirement / approved by UHBVNL consisting of the following. - Cubical panel free standing floor mounting type made out of sheet steel 16 SWG CRCA sheet with channel iron base frame spray painted with strong synthetic light grey enamel paint as per size and design approved by the UHBVNL. - 3 Nos. 11KV CTS of rating as approved by UHBVNL for indoor installation of approved make of UHBVNL. - 1 Nos. 11KVPTS 11000/10 VA burden 0.5 accuracy oil filled suitable for indoor installation of approved make of UHBVNL. The cubical panel will be completed in all respect including inter connection, internal wiring with PVC copper cable, its testing and approval of all item by UHBVNL cost of all testing/ approval charges or all items of UHBVNL with a guarantee of one year from the date of commissioning. including cost of all labour and material required to complete the job in all respect upto the entire satisfaction of the engineer in charge of the work NS

59 - Supply & Erection of Digital Electronic Meter 3 phase 4 wires 0.5 accuracy for recording reading in KWH of make and rating approved by UHBVNL with push button display operating system for different kind of readings.F57 including cost of all labour and material required to complete the job in all respect upto the entire satisfaction of the engineer in charge of the work. NS

60 - Supply & Erection of bucket stand suitable for 6 Nos. fire buckets,(but without bucket) including the cost of welding and painting of complete stand with one coat of red oxide and 2 coats of approved paint of red colour with all labour and material required to complete the job in all respect up to the entire Satisfaction engineer in charge of the work. Stand made out of GI pipe 32mm dia. NS

61 - Supply & Erection of rubber mat of size 1Mx2 M X 12mm thick suitable for 11 KV ISI marked complete in all respect upto the entire satisfaction of the engineer In-charge of the work. Make & Model as approved by Chief Electrical Inspecter Haryana. NS

62 - Supply & erection of fire extinguisher ISI marked Co 2 type 4.5 Kg. Capacity as Per ISI 7285 duly erected on wall with hook including the cost of hook, screw etc. with all the labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer In charge of the work. Make: Ajay, Zenith, Minimax. NS

63 - Supply & Erection of fire buckets of 9 ltr. capacity made out of 24guage G.l sheet and duly painted with one coat of red oxide and 2 coats of approved paint in red colour and written with the fire' as per fire protection necessar sand filling in the bucket hung the bucket on stand with all labour and material required to complete the job all respect up to entire \satisfaction of the Engineer m charge of the work NS

64 - Providing and fixing of wire mesh jali around the transformer of size 4’ x 8’ made out of 75x25x3.25mm jali fixed with angle iron frame made out of M.S Angle 50 x 50 x 6 mm support of M.S flat 50 x 6mm and fixed in C.C block 1:2:4 including cutting, welding etc. as per drawing complete in all respect upto the entire satisfaction of the Engineer in charge NS

65 - Supply & erection of lighting arrestor model ALPRO / Alastom/ LEMCO make suitable for 11KV 3 Phase 50 HZ ground neutral system comprising of spare gape type queen gap type in series with non linger resistar element house in Horizontally scale poreclam bushing with line and ground terminal along with mounting clamps conforming to ISS 3070 (Part-I) of 1985 with latest amendment with all labour and material required to the complete in all respect up to entire satisfaction of the Engineer-in-Charge of the works. NS

66 - Supply of Disc insulator Rashtriya / Jayshree / BHEL make with Disc fitting T&C type complete in all respect with erection of the same upto the entire satisfaction of the Engineer in Charge of work NS

67 - Supply & Erection of cubical type dust and Vermin proof LT automatic power factor control panel 60KVAR capacity. suitable for automatic operation and control of power factor within the set limits free standing floor / wall mounting made out of 16 gauge M.S. sheet duly powder coated suitable for operation of 3 phase 4 wires 50 cycles per second 400/440V.A.C. supply equipped with the following. - 1 No. automatic power factor control relay of GE/L&T/ Neptune make. Incomer MCCB (35KA) = 100amp. with back up protection of HRC Connection from incomer MCCB to bus bar by means of copper wires of suitable size of requisite capacity insulated with PVC. 4 No. 10 KVAR & 4nos 3 phase 5 KVAR capacitor of L&T /GE / Neptune-ducat LL-10 (Mono16) long life make. (Total 60 / KVR) Installed and duly wired inside panel with axial flow fan controlled through thermostat. The panel will be complete with all internal wiring with PVC copper wire, inter connection etc. complete in all respect with all labour and material up to the entire satisfaction of the Engineer-in-charge of the work. NS

68 - Supply and erections of V-shape X-arm on PCC poles as per state electricity Nigam design and requirement it should be made out of MS channel size 75 x 40 x 6mm complete in all respect . NS

69 - Providing & fixing of stay set complete with stay wire and egg insulator as per specification upto the entire satisfaction of Engineer-in-Charge for HT/LT line. NS

70 - Supply and erection of guards made of G.I. wire 8 SWG with guard real for HT/LT line complete in all respect upto the entire satisfaction of Engineer-in-Charge. NS

71 - Supply and erection of fuse unit L.T. side 400 amp. on LT pole complete with wooden board cleats, aluminum strips M.S. clamp & M.S. Nuts& Bolts including all petty, material required upto the entire satisfaction of Engineer-in-Charge. NS

72 - S/E of 11 KV danger plate 8” x 6” duly painted with enamel paint NS

73 - Supply and fixing of L.T. phase separator 4 lines of PVC complete in all respect upto the entire satisfaction of Engineer-in-Charge. NS

74 - Supply, Erection, testing and commissioning of outdoor type Transformer- 200 KVA 11/0.433 K. V.3 Phase-50 cycles copper wound outdoor type as per latest ISI specification up to the entire satisfaction of the Engineer-in-charge of work as detailed as under: No. load voltage ratio 11/0.433 K V. No. of Phase = 3 Frequency cycles = 50HZ Type- double wound core type copper wound Cooling = ONAN Duty = outdoor Vector group/ISS-DYN 11/IS- 2026 with latest ISI specification. Tapping Range ± 5% in steps of 2.5% Temperature rise over ambient 50° C Attitude= upto 1000metres above N.S.L. Fitting/Accessories Provided. Drain cum filter valve. 4Nos. plain roller uni directional Rating & diagram plate Two earthing terminals Tap changer off load Externally hand operated Oil Conservator with fitting Knob & Cap Plain oil level with Minimum level marking. Lifting arrangement Therma meter pocket with one dial type thermometer. Inspection of housing with covers Silica jel breather First filling of oil. Explosion vent. Air release plug. Termination:- HV 3 pole bushing suitable for 1 No. 3 core up to 120 sqmm XLPE cable including the cost of suitable thimbles. LV : 4 Pole bushings including neutral suitable for 2 No. 240 sq.mm 3.5 core poly vinyl chloride cable having extended copper bars of requisite capacity duly tinned from L. T. bushing for making connection with cable including the cost of suitable thimbles, including erection of same on existing masonary plateform complete up to entire satisfaction of the Engineer-in-Charge of the works.

75 - S&E of single arms bracket made of 50mm dia GI pipe B class 0.75 mtr. Long with 25mm dia bottom pipe GI with coller pipe (GI) 100mm dia 60cm Long with MS nipple as required for fixing of fitting duly welded at end of bracket top covered with ornamental cap duly welded, painted 2 coats of aluminium paints on bracket and golden paint of ornamental cap including the cost of labour and petty material etc. complete in all respect upto the entire satisfaction of Engineer-incharge. NS

76 - Supply and erection of LED Regular Streetlight Luminaires 72 W of Makes: Bajaj / Crompton / Philips / Wipro with Pressure die cast aluminium housing with lens and accessories required to complete the job in all respect including erection on existing pole for fixing including connection of the same upto the entire satisfaction of Engineer in Charge of the work. NS

77 - Supply and erection of LED Flood light Luminaires 120W of Makes: Bajaj / Crompton / Philips / Wipro / with lense with high power LED street light in aluminium PDC housing, toughened glass cover with IP 65 protection and accessories required to complete the job in all respect including erection and fixing including connection and other petty material for the same upto the entire satisfaction of Engineer in Charge of the work. NS