REPAIR/ REPLACEMENT OF INTERNAL WIRING, FITTING AND FIXTURE IN OTM ACCN OF RRC, MH AND MES AT FATEHGARH CANTT

Amount

Taking down copper/aluminium point wiring of any description and any position (light, fan, socket or power point) complete, including fixture and fittings such as switches,socket, ceiling rose,lamp holder,pendants, bracket and regulator etc and removing material from site including making good disturbed surface to match with the existing surface complete all as specified and as directed .

Taking down Aluminium sub main wiring of any description and in any position including GI earth wire and making good disturbed surfaces to match with the existing surface roof/wall/floor complete all as specified and as directed by the Engr-in-Charge.

M&L for point wiring for One light/ holder/fan/exhaust fan/ bell point controlled by one switch switch 5/6 Amps with 1100 volt grade PVC insulated and unsheathed 1.5 Sq mm (FRLS) multistranded copper conductor cable with continuous earth wire of 1.5 Sq mm (FRLS) multistranded copper conductor cable PVC insulated and unsheathed, drawn in & including concealed PVC rigid conduit medium grade with fittings (ISI marked) not less than 20 mm dia & 1.6 mm thick sunken pressed steel galvanised terminal boxes with top cover ISI marked plastic laminated hylam sheet for housing/ fixing switches etc complete all as specified & directed. Note:- (i) The quoted rate is deemed to be included for the chases cutting. (ii) Cutting chases for concealed shall be made good with using CM 1:4 and surface finished to match the existing surface & Colour.

..ditto as above but for one 5 pin 5 Amp switch socket combination point on an independent board …ditto as above…

..ditto as above but for but one 5 pin 5 Amp socket point controlled by one switch on same board …ditto as above…

..ditto as above but for one 16 Amp 6 Pin switch socket combination independent with 2.5 Sqmm FRLS unsheathed copper conductor single core multistranded …ditto as above…

M&L for point wiring for One light/ holder/fan /exhaust fan/ bell point controlled by one switch 5/6 Amps with 1100 volt grade PVC insulated and unsheathed 1.5 Sq mm (FRLSH) multistranded copper conductor cable with continuous earth wire of 1.5 Sq mm (FRLS) multistranded copper conductor cable PVC insulated and unsheathed, drawn in & including Surface PVC rigid conduit of suitable size medium grade with fittings (ISI marked) not less than 20 mm dia fixed with pvc clamp of suitable size & 1.6 mm thick sunken pressed steel galvanised terminal boxes with top cover ISI marked plastic laminated hylam sheet for housing/ fixing switches etc for the complete all as specified & directed.

..ditto as above but for one 5 pin 5 Amp switch socket combination point on an independent board complete all as specified and as directed.

..ditto as above but for one 5 pin 5 Amp socket point controlled by one switch on same board complete all as specified and as directed.

..ditto as above but for one 16 Amp 6 Pin switch socket combination independent with 2.5 Sqmm FRLSH unsheathed copper conductor single core multistranded ..ditto..

S&F Switch Piano Flush type 6 Amp single pole one way complete all as specified and as directed.

S&F Switch Socket Combination 2 in 1 flush type 6 Amp 5 Pin complete all as specified and as directed.

S&F Switch Socket Combination 5 in 1, 16 Amp flush type complete all as specified and as directed.

M&L for Lamp Holder PVC/Polycarbonate type insulated body with back plate angle type for batten fittings incl LED bulb of 9 Watt and colour temp 6500K suitable for fix in angle holder complete all as specified and directed.

S&F Bell Push AC 230 volts complete all as specified and as directed.

S&F Call Bell Ding Dong AC 230 volts complete all as specified and as directed.

S&F Electronic Fan Regulator 5 stepped type complete all as specified and directed

S&F Ceiling Rose PVC/Poly carbonate isolated body three terminal AC 230 volts complete all as specified and directed.

M&L for Sub Main Wiring with two single core 6 Sqmm FRLS copper conductor PVC insulated and unsheathed cable including PVC conduit medium grade (appropriate size) concealed in wall for sub main connection including 6 Sqmm FRLS insulated multistranded unsheathed copper conductor used as a earth wire to common earth and connection to earth dolly complete all as specified and as directed. ( Note :- Two runs of 6 sqmm FRLS and one run of 6 sqmm FRLS copper conductor shall be measured as one unit length.)

Supply and fixing in replacement of VTPN DB suitable for Mounting MCCB as Incomer of rating 100 Amp Vertical distribution board 4 way with suitable rated bus bar having IP-43 protection and double metal door concealed in wall including connection with aluminium thimbles as required complete all as specified and as directed.

Supply and fixing in repair MCB distribution board SPN 240 Volt 8 way with 200 Amp rated bus bar having IP-43 protection and double metal door concealed in wall including connection with copper thimbles as required complete all as specified and as directed.

Supply and fixing in repair MCB distribution board SPN 240 Volt 4 way with 200 Amp rated bus bar having IP-43 protection and double metal door concealed in wall including connection with copper thimbles as required complete all as specified and as directed.

S&F in repair of MCCB 100 Amp, 16KA, 4 Pole including complete electrical connection by appropriate size of copper lugs complete all as specified and directed.

S&F in repair of MCB SPN 40 Amp 240 volt 'C' 10 KA curve complete all as specifed and directed.

S&F in repair MCB SP 6 to 32 Amp 240 Volt 'C' curve 10 KA complete all as specified and directed.

S&F in repair LED batten 2 Ft surface / wall mounted with specially designed powder coated aluminium housing, high optically efficient polycarbonate diffuser, in built electronic driver duly wired upto terminal block, power consumption < 10W luminaire lumen >1000 lm, system efficiency of > 100 lumens / W, with LED binning as per ANSI Bin C78.377A, photo biological safety report as per IEC624718 & electrical insulation class I, Ingress protection IP 20, colour rendering index CRI>80, temp range 0 to 45 ºC, driver efficency >85%, power factor >0.9, THD <20% as per IEC 61000-3-2, colour temp - 6500K, surge protection 2.5 KV, 50000 burning hrs (min) as per L70 criteria, two stages isolated constant current operated driver with range 150-270V AC and safety extra low voltage safe level <60V DC as per IEC standard with LM70 & LM80 certification and connecting the same in electric source with and using PVC sheathed and insulated 3 core copper conductor cable of size 0.75 Sqmm and fixing arrangement for fixing the light fitting including marking CA No on LED fitting with permanent marker style and size decided by eng-in-charge complete all as specified and directed.

S&F in repair LED Batten 4 Ft surface / wall mounted with specially designed powder coated aluminium housing, high optically efficient polycarbonate diffuser, in built electronic driver duly wired upto terminal block, power consumption < 20W (4 FT 20 W), luminaire lumen >2000 lm, system efficiency of > 120 lumens / W, with LED binning as per ANSI Bin C78.377A, photo biological safety report as per IEC624718 & electrical insulation class I, Ingress protection IP 20, colour rendering index CRI>80, temp range 0 to 45 ºC, driver efficency >85%, power factor >0.9, THD <20% as per IEC 61000-3-2, colour temp - 6500K, surge protection 2.5 KV, 50000 burning hrs (min) as per L70 criteria, two stages isolated constant current operated driver with range 150-270V AC and safety extra low voltage safe level <60V DC as per IEC standard with LM70 & LM80 certification and connecting the same in electric source with and using PVC sheathed and insulated 3 core copper conductor cable of size 0.75 Sqmm and fixing arrangement for fixing the light fitting including marking CA No on LED fitting with permanent marker style and size complete all as specified and directed.

S&F LED security light fitting 1x15 watt new generation energy saving & environmental friendly long life LED street light made up pressure die-cast aluminium housing with high power LED as lighting source and lens embedded PC having top opening separate driver compartment with IP-65 protection and impact resistence of IK07 for building security purpose complete all as specified & directed by Engineer-in- charge.

S&F in repair LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete.

S&F in renewal suspended / surface mounted with 1X 4' LED luminaire including 15 mm dia BSP steel conducit pipe of suitable length full panel LED luminaire with white powder coated housing acting as heat shrink and frame in CRCA sheet, high efficiency LED grade diffuser, in built electronic driver duly wired up to terminal block, power consumption < 30W, luminaire lumen > 3500Lm and system efficiency > 120 lm/W, CRI>80,, colour temp - 5700 K, Ingress protection IP 20, driver efficiency > 85%, 50000 burning hours (min) as per L 70 criteria, abmient temp 0 to 500C, power factor >0.95, THD <10%, surge protection in CM - 3 KV, two stages isolated constant current operated driver with range 150 - 270 V AC and safety extra low voltage safe level < 60 V DC as per IEC standard with LM 79 & LM 80 certification complete all as specified and directed.

S&F in repair to metal plug & socket DB with metal plug and MCBs dobule pole and neutral enclosere with a two pin earth plug and socket suitable for 20 Amp complete with one single pole MCB complete all as specified and directed.

Supply and Laying cable XLPE Insulated screened PVC bedded, galvanized steel strip armoured service cable pole to building electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 Sqmm 4 core including taking down of UG cable complete all as specified and directed.

S&F 40 mm bore GI Tubing light grade with all fittings laid across road, in trenches or across PCC drain, along electric pole or floor/wall for cable protection with suitable size of MS Clapms and nut and bolts/washer complete all as specified and directed.

Supply and laying sand with approved fine grade sand around cable in cushioning for protection of under ground cable complete all as specified and as directed. Note:- (only punned and consolidated volume to be measured)

Supply and laying kiln burnt bricks best quality locally available old size sub class 'B' bricks laid flat in trenches with axis of brick perpendicular to the axis of cable for cable protection complete all as specified and as directed.

Excavation in trenches not exceeding 1.5 mtrs wide and not exceeding 1.5 mtrs in depth for laying of cables including getting out in any type of soil complete all as specified and directed.

Returning filling in including spreading, leveling ,and well ramming, in layers not exceeding 25 cm each layer of any type of soil complete all as specified and directed

Removing surplus excavated material from site not exceeding 50 mtrs from starting point and depositing where directed at level not exceeding 1.5 mtr above the starting point complete all as specified and directed

M&L for earthing complete with galvanised steel earth plate electrode 600 x 600 x 6 mm thick, burried directly into the ground (earth pit not less than 2.25 mtr below ground level) with top edge of the plate not less than 1.5 mtr below normal ground level, connected to GI earth wire 4 mm dia by means of bolts, nuts, check nuts, and washers of galvanised iron or steel all as shown iln electrical plate No - 3 connected to earthing test point all as specified or indicated including excavation and connected earth work, PCC chamber and cover, watering pipe, funnel wire mesh but with earth lead protection pipe and test on completion after dismantling unserviceable erthing (above GL only) including dismantling of exsisting earthing complete all as specified and as directed. (Note :- On testing after completion if desired earth resistence is not obtained, the earthing will be redone at no extra cost.)

S B ENTERPRISES

M/S Shree Gopal Engineers & Contractor

MS. BK BROTHERS AND CO

M/S SRI JAGDAMBE TRADERS