REPAIR REPLACMENT IMPROVEMENT OF LT DISTRIBUTION NETWORK APFC PANEL AND OTHER CONNECTED WORK IN INF ARTRAC LINE MH GOLF VIEW AND SURROUNDING AREA AND REPAIR MAINT IMPROVEMENT OF INCINERATOR AND LAUNDRY MACHINE INSTALLED AT MH AND OTHER CONNECT

Amount

Excavation in trenches in any type of soil not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, etc or not exceeding 10 Sqm on plan for laying of cable, pipe, shafts, cesspits, manholes, pier holes, etc complete all as specified.

Returning, filling in excavated approved soil, including spreading, leveling, watering and well ramming in layers not exceeding 25cm each complete.

Removing excavated soil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete.

M&L for Sand cushioning with fine dry unwashed sand in trenches for protection of cables complete. NOTE : Thickness shall be measured after panning down.

M&L for old size sub class ‘B’ bricks, laid in trenches as cable covers .

S&F steel tubes galvanised light grade ISI marked 40mm bore for protection of cable under floor, road and on wall complete.

S&F steel tubes galvanised light grade ISI marked 80 mm bore for protection of cable under floor , road and on wall complete.

M&L for repair / maintenance of feeder pillar boxes,APFC panel body by cutting out and removing corroded portion of MS sheet with new MS sheet of existing thickness and making necessary locking arrangement,hinges and making panel board in good condition including painting with one coat of synthetic enamel paint inside and outside the panel and repairing bus bar of any size and type complete all as specified and directed by Engineer-in-Charge. Note:- 1. MS sheet shall be measured and paid separately under respective items. 2. Welding work as required for any making panel serviceable shall deemed to be included in the quoted rate. 3. Necessary control cable connection as required for panel shall deemed to be included in the rate quoted

S&F in replacement of HD type, 440 V, 50 Hz heavy duty cylindrical type power capacitor of size 25 KVAR to the existing APFC Panel all as directed by Engineer-in-charge. Make :- Neptune or other equivalent in Havells.

All as per item No 9 above but for 12.5 KVAR

All as per item No 9 above but for 6 KVAR

S&F in replacement of box type power capacitor, heavy duty of size 5 KVAR, 480 V to the existing APFC Panel all as directed by Engineer-in-charge. Make :- Neptune or other equivalent in Havells.

All as per item No 12 above but of 10 KVAR

All as per item No 12 above but of 15 KVAR

All as per item No 12 above but of 25 KVAR

All as per item No 12 above but of 50 KVAR

S&F in replacement of aluminium reactor of size 50 KVAR to the existing APFC panel as directed by Engineer-in-charge. Make :- Havells /Indoasian / L&T

S&F in replacement of 8 step APFC controller digital type in existing APFC panel complete all as specified and directed by Engineer-in-charge.Make :- Neptune or equivalent in Havells

All as per item No 18 above but of size 12 step

Supply only 3mm thick MS sheet for panel

S&F in replacement of Power contactor 3P, 330 Amps, 50 Hz all as specified. Make :- Havells/Indo Asian / Neputune

S&F in replacement of Power contactor 3P, 225 Amps, 50 Hz all as specified. Make :- Havells/Indo asian/Neputune

S&F in replacement of capacitor duty contactor with 3 pole,415 volt,3 phase, mini contactors contacts with auxiliary contacts 1 NO+1NC of Rating 5 KVAR complete all as specified.

All as per item No 23 above but 10 KVAR

All as per item No 23 above but 15 KVAR

All as per item No 23 above but 25 KVAR

S&F in repair PVC insulated copper wire single core of multi stranded of size 70 sqmm. Make :- Havells / Indo Asian / Polycab

M&L for attending external electric complaints by opening / disconnecting the electrical connection of defective / burnt out underground LT cable of any size & any core from main switch / DB / junction box / LT panel / L T O/H line etc. and taking out the required length of cable from existing loop and remove cut the defective cable and replace the same with new cable as per existing size including providing necessary thimbles / connectors at cable end and reconnecting the cable in previous location with existing main switch / DB / Junction box / LT panel / OH line etc. and make necessary electic connection as functionable in all repspects including testing on completion all as specified and directed by Engineer-in-charge.

Note:- (A) The rate quoted shall deemed to be inclusive of the following: (i) Necessary earth work excavation in any type of soil, returning, filling and removing extra soil. (ii) Existing bricks, sand,GI protection pipe etc. shall be removed carefully and stacks neatly near site and same shall be re- laid after attending fault/defect. (iii) Distrubed surface of road, floor etc. shall be make good to match with existing surface. (iv) Required numbers of electrician and helper shall be deployed for attending complaints regulerly on daily basis and contractor shall collect the complaints details from complaint cell of AGE E/M No.1 and same shall be rectified / attended within an hour and report shall be submitted to Engineer-in-charge or their authorised representative. (B) Please note that payment shall be made to contractor one time only for this items. if any fault/ default occured again on the same location/ DB/junction box/panel during currency of contract, the same shall be rectified by the contractor without any extra cost to Govt. in terms of condition 46 of IAFW of genral condition of contracts. (C) Additional bricks,sand,GI pipe etc. as required for cable protection and cushioning shall be measured and paid separetely under relevent item.

M&L for dismantling / disconnecting / removing the faulty / burnt out overhead conductor of any type / size from insulator of HT / LT pole any type by making proper shutdown from department and removing of tree / branches if any fell on Over Head Line, loose the binding wire in each insulators and disconnecting cable connection as required, remove the burnt / damage conductor / earth wire and making necessary joint with new ACSR conductor of suitable size as per existing as directed, restretching all the loose spans of ACSR conductors, earth wire etc. with insulator and providing binding wire of existing size to tigheting and making LT/HT cable in existing position and make electric connection as functionable in all respects including testing on completion allas specified and directed by Engineer in charge.

NOTE: The rate quoted shall deemed to be inclusive of the following:- (i) Tools and plants such as ladder,rope, cutter, axes, knife etc. as required for cutting and removing tree/branches if any fall on OH line. (ii) Insulator,binding wire etc. as required in addition to existing shall be provided by the contractor. (iii) Required numbers of Elecrician and helper shall be deployed for attending complaint regularly on daily basis and contractor shall collect the complaint details from complaint cell of AGE E/M No. 1 (iv) Additional ACSR conductor and earth wire shall be measured and paid separetely under relevant items.

M&L for trimming / pruning of tree branches touching to the LT over head line or near to the LT over head line as per direction of AGE E/M /JE in charge complete including removing the tree branches from site complete all as specified and directed . NOTE - (a) written shut down shall be obtained from concerned JE / AGE E/M before carrying out the trimming work in hand by contractor (b) span from one pole to next pole shall be 30m to 50m and shall be considered as a Each job (c) T & P such as ladder , rope, cutter , axes and other related material shall be provided by the contractor.

M&L for restringing of loose over head conductor/GI earth wire of any size and type after untyeing binding wire from insulators/cross arms to achieve permissible sag limit of over head line including re-fixing of broken conductor by new binding wire of proper size and pruning of tree branches of concerned spans and jointing of jumpers properly complete all as specified and directed at site. Note:- (i) One job shall consist of one span of 3-phase 4-wire over head line. (ii) The distance of one span shall be 30 to 50 meter.

Maintenance of indoor sub stations, including cleaning of premises and surroundings upto 5m from outer face of wall, checking of oil level of transformers, cleaning and dusting out of transformers, panel boards, cleaning of earth pits to keep free from vegetation etc complete all as specified and directed by Engineer-in-Charge.

All as per item No 32 here in before but for out door sub station including levelling of loose filled aggregate around sub station.

S & F in replacement XLPE insulated and PVC armoured heavy duty electric cables with aluminum conductor, 1100 volt grade of size 3.5 core 25 sqmm in trenches/through pipes/ducts or on poles/walls jointing to O/H conductor, LT panels, main switch with suitable size aluminum lugs and testing complete all as specified & directed for the following sizes:- Note : (a) Excavation shall be measured and paid seperately under respective items of Sch 'A' (b) All required lugs of suitable sizes according to size of cable shall deem to be included in the rate qoated.

All as per item No 34 above but for 35 Sqmm 3.5 core.

All as per item No 34 above but for 50 Sqmm 3.5 core.

All as per item No 34 above but for 70 Sqmm 3.5 core.

All as per item No 34 above but for 95 Sqmm 3.5 core.

All as per item No 34 above but for 120 Sqmm 3.5 core.

S&F in repair MCCB 3 pole, 415 volts, adjustable type 160 Amps with breaking capacity 36 KA (Make : ABB, L&T & Schneider)

All as per item No 40 here-in-before but for 200 Amps.

All as per item No 40 here-in-before but for 250 Amps.

All as per item No 40 here-in-before but for 350 Amps.

All as per item No 40 here-in-before but for 400 Amps.

S&F in repairs straight through joint ( Epoxy joint) for following size PVC insulated and sheathed aluminium cable complete for 2 core 16 sqm

All as per item No 45 above but for 120 sqmm to 150 sqmm

All as per item No 45 above but for 185 sqmm

M&L for disconnecting conductor,insulator,channel,street light bracket etc from LT pole of height 9 meter and remove LT Pole from safe ground and shifting the pole to other location within camp and re-install at new location all as specified and directed by Engineer-in-charge . NOTE : (a) Quoted rate shall be inclusive for loading, unloading transporting pole to new location through vehicle and tools and plants as required. (b) Earthwork excavation, PCC shall be measured and paid separately under relevant items.

M&L for repairing existing LT panel of any size and any description by welding the damaged portion of panel board including providing MS sheet as required to making good the damaged portion of panel,hinges,aldrop bolt etc and painting with one coat of synthetic enamel paint of approved colour internally and externally complete all as specified and directed Engineer-in-Charge

S&F in repair Post top lantern 35 watts new generation, energy saving ,environmental friendly ,long life asthetically designed with symmetrical light distribution, spun aluminium landscape luminaire with high power LEDs as light source , 240 volts with IP 65 complete all as specified. Make : Havells /Philips/Bajaj

Supply install in replacement of sturdy LED Bollard with excellent light out put through PMMA window ensuring maximum illumination aspect in surrounding with IP 65 including providing necessary foundation concrete with PCC 1:2:4 complete all as specified and directed. Make : Havells /Philips/Bajaj

S&F PVC/ Fibre Separator for LT Lines 1100 Volts OH Conductor 2 Wire system for horizontal spacing of Conductor, fixing with nuts, bolts, washers, etc , complete all as specified and as directed.

S & F PVC/ Fibre Separator for LT Lines 1100 Volts OH Conductor 4 Wire system for horizontal spacing of Conductor, fixing with Nuts, Bolts, Washers etc. complete all as specified .

Supply and fill transformer oil EHV grade as per IS 335 of 1993 Part II in sealed drum to filling/top up of transformer of capacity 63 KVA to 1200 KVA complete all as specified and directed. Make:-SAVITA

Supply and laying or fixing or passing through pipe in replacement 1100 volts grade heavy duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and over all PVC sheathed 10 sqmm 2 Core, nominal cross section as in service connections all as specified.

supply and laying industrial cable with copper conductor PVC round sheathed (flexible) of size 10 sq mm.

M&L for treating the existing high resistance earthing pit by pouring salt water solution (5kg of salt diluted in 20 litres of water ) in trenches ,all around the earthing pit with radius of 60 cm from the centre of the earth pit and depth not less 30cm below the ground level all as specified and directed by the Engineer -in-Charge

M&L for marking of Pole No on existing HT / LT pole of any type by , making 15 cm dia circle with black synthetic enamell paint & writing letter of length 8 cm long & 1.5 cm width with white paint complete all as specified & directed by Engineer-in-charge.

M&L for attending KWH meter complaints by repairing like rectifying loose connections in meter and switch gears, checking and caliberation of meter to ensure proper functioning, testing, sealing and submission of reading after repairing to Engineer-in-Charge all as speciified and direted.

S&F in repairs connecting and testing open execution on load change over in existing DG set Panel of the following capacity, suitable for 415 volts, 50 Hz, 400 Amp , 4 pole with extended terminals type, inter locked to prevent opening when the Switch is in ON Position, connecting and testing complete all as specified and directed. Make:- ABB/ L&T/ Schneider.

All as above but 320 Amps.

All as above but 250 Amps.

All as above but 200 Amps.

All as above but 160 Amps.

All as above but 63 Amps.

M&L for Servicing, taking out & removing unserviceable / defective parts / spares,cleaning, servicing,descaling of water chambers, door gaskets ,oiling, leath work and greasing of necessary parts, refixing the serviceable parts in position after servicing, replacement of unserviceable pats, refixing of all accessories and testing on full load complete all as specified and directed for capacity of 30 Kg Laundry machine at MH Mhow . Note- Spares for Laundry machine shall be measured and paid seprately under relevant item.

Supply only Bearing suitable for above machine as per sample, (Set of three)

Supply only Oil seal as per sample, (Set of four)

Supply only Oil set lock pin as per sample, (Set of four)

Supply only Fan Belt, as per sample (Set of Two)

M&L for replacement of old Shock absorbers (Set of Eight) after removing from luandary machine and reassembling the same to the existing position and testing complete all as specified and directed

M&L for dismantling, and taking out induction motor for repair work by rewinding of motor 12.5 HP Clock wise and Anti clock wise movement of existing guage including transportation to local workshop from existing place and vise versa and refixing the same at its original place and testing complete all as directed by Engineer-in-charge.

M&L for replacement of Hose Pipes (Set of five ) from Luandary Machine and reassembling the same to the existing position and testing complete all as specified and directed

M&L for replacement of clips for Hose pipe ( Set of ten) from Luandary Machine and reassembling the same to the existing position and testing complete all as specified and directed.

M&L for replacement of Air Solonite Switch from Luandary Machine and reassembling the same to the existing position and testing complete all as specified and directed.

Supply only Special Grease for High tempreature.

M&L for replacement of sensor drain valve from Luandary Machine and reassembling the same to the existing position and testing complete all as specified and directed.

M&L for replacement of sensor autocut from Luandary Machine and reassembling the same to the existing position and testing complete all as specified and directed.

M&L for replacement of Door Gaskit from Luandary Machine and reassembling the same to the existing position and testing complete all as specified and directed.

M&L for replacement of PU pipe from Luandary Machine and reassembling the same to the existing position and testing complete all as specified and directed.

M&L for replacement of PU Conductor from Luandary Machine and reassembling the same to the existing position and testing complete all as specified and directed.

Suply only chemical sulferic acid for cleaning purpose

Supply only nut & bolt as per existing sample for Laundry Machine

M&L for replacement of heating element of 3 KW from Luandary Machine and reassembling the same to the existing position and testing complete all as specified and directed.

M&L for replacement of temperature guage from Luandary Machine and reassembling the same to the existing position and testing complete all as specified and directed.

M&L for replacement of door lock from Luandary Machine and reassembling the same to the existing position and testing complete all as specified and directed.

M&L for replacement of door lock pistol from Luandary Machine and reassembling the same to the existing position and testing complete all as specified and directed.

M& L for replacement of door lock handle from Luandary Machine and reassembling the same to the existing position and testing complete all as specified and directed.

M&L for replacement of balancing spring from Luandary Machine and reassembling the same to the existing position and testing complete all as specified and directed.

M&L for servicing of 15 Kg capacity Laundry Machine at MH Mhow by taking out , removing unserviceable / defective parts / spares,cleaning , descaling of water chambers, door gaskets ,oiling, leath work and greasing of necessary parts, refixing the serviceable parts in position after servicing, replacement of unserviceable parts, refixing of all accessories and testing on full load complete all as specified and directed . Note: Spares as required for servicing of Machine shall be measured and paid seprately under relevant item.

M&L for replacement of door gasket from Luandary Machine and reassembling the same to the existing position and testing complete all as specified and directed.

M&L for dismantling and taking out induction motor for repairing by rewinding of motor 25 HP capacity clock wise and anti clock wise movement of existing guage including transportation to local workshop from exiting location and vise versa and refixing the same at its original place and testing on completion complete all as directed by Engineer-in-charge.

Supply only bearing suitable for above 15 Kg Laundry Machine as per existing No Note: Three Nos of bearing shall be measured as each set

M&L for replacing hose pipes from Luandary Machine and reassembling the same to the existing position and testing complete all as specified and directed Note: Five Nos of pipes shall be measured as each set

M&L for replacement of fan belt from Luandary Machine and reassembling the same to the existing position and testing complete all as specified and directed Note: Two Nos of pipes shall be measured as each set

M&L for replacement of air solonite switch from Luandary Machine and reassembling the same to the existing position and testing complete all as specified and directed.

M&L for replacement of sensor drain valve from Luandary Machine and reassembling the same to the existing position and testing complete all as specified and directed.

M&L for replacement of sensor autocut from Luandary Machine and reassembling the same to the existing position and testing complete all as specified and directed.

M&L for replacement of PU pipe from Luandary Machine and reassembling the same to the existing position and testing complete all as specified and directed.

M&L for replacement of PU Conductor from Luandary Machine and reassembling the same to the existing position and testing complete all as specified and directed.

M&L for replacement of shock absorbers (eight nos ) from Luandary Machine and reassembling the same to the existing position and testing complete all as specified and directed

M&L for replacement of heating element of 3 KW from Luandary Machine and reassembling the same to the existing position and testing complete all as specified and directed.

M&L for replacement of oil seal as per sample (four nos ) from Luandary Machine and reassembling the same to the existing position and testing complete all as specified and directed.

M&L for replacement of oil set lock pin ( four nos) from Landary Machine and reassembling the same to the existing position and testing complete all as specified and directed.

M&L for replacement of clips for hose pipe ( ten nos ) from Luandary Machine and reassembling the same to the existing position and testing complete all as specified and directed.

M&L for replacement of door lock pistol from Luandary Machine and reassembling the same to the existing position and testing complete all as specified and directed.

M&L for replacement of door lock handle from Luandary Machine and reassembling the same to the existing position and testing complete all as specified and directed.

M&L for replacement of balancing spring from Luandary Machine and reassembling the same to the existing position and testing complete all as specified and directed.

M&L for repairing /cleaning / greasing / descaling /Servicing / maintenance of Laundry plant Wash Dryer of capacity 15 kg at MH Mhow complete all as directed by Engineer-in-Charge . Note : Required spares shall be measured and paid seperately under relevant item.

Supply only fan belt (Two nos)

M&L for replacement of PU pipe from Laundary Machine and reassembling the same to the existing position and testing complete all as specified and directed.

M&L for replacement of PU Conductor from Luandary Machine and reassembling the same to the existing position and testing complete all as specified and directed.

M&L for replacement of air solonite switch from Luandary Machine and reassembling the same to the existing position and testing complete all as specified and directed.

M&L for replacement of heating element of 3 KW from Luandary Machine and reassembling the same to the existing position and testing complete all as specified and directed.

M&L for replacement of sensor autocut from Luandary Machine and reassembling the same to the existing position and testing complete all as specified and directed.

S&F Contactor for Dryer panel

M&L for repairing and maintenance of Automatic Press Laundry plant at MH Mhow complete all as specified and directed by Engineer-in-charge. Note: Required spares shall be measured and paid seprately under relevant item.

Supply only air solonite switch

Supply only sensor autocut

Supply only PU conductor

Supply only PU pipe of existing size

Supply only ID fan

Supply only drain level gauage

M&L for replacement of Hydrolic pump from Luandary Machine and reassembling the same to the existing position and testing complete all as specified and directed.

M&L for dismantling and taking out induction motor for repairing and rewinding of Motor 3 HP clock wise and anti clock wise movement of existing guage including transportation to local workshop from existing place and vise versa and refixing the same at its original place and testing complete all as directed by Engineer- in-Charge.

M&L for repairing and maintanance of Air Compressor of Laundry plant at MH Mhow complete all as directed by Engineer-in-Charge Note : Spares shall be measured and paid seperately under relevant item.

Suppply only pistol ring

Supply only oil seal

Supply only fan belt

Suuply only auto pressure guage

Supply only air pressure timer

Supply only packing Kit

S&F in replacement of synchronous motor , Type: ME 7991 , 220 V +/- 10 %, 50 HZ, 3 W all as specified and directed by Engineer-in-charge. Make:- MUKUND SR. NO- L13

Taking out / removing unserviceable VFD installed in Laundery machine of 12.5 HP Motor capacity Make: Toshiba for repairing at Manufacturer workshop after repairing , refixing the same at its original position and testing on full load complete all as specified and directed by Engineer - in- Charge. Note:- Repairing should be carried out in TOSHIBA'S Authorised service centre / w rkshop

M&L for servicing incinerator of 20 Kg/ hour capacity Model No: PGVS 40 of Make: THERMAX installed at MH Mhow by taking out and removing unserviceable / defective parts / spares , cleaning, servicing ,descaling burner chambers, door gaskets and other necessary parts and refixing the all parts in position after servicing and testing on full load complete all as specified and directed by Engineer-in-Charge. Note : Spares shall be measured and paid seprately under relevant item .

S&F in repair spray Nozzle

S&F in repair photocell

S&F in repair ignition electrode (4 Nos of electrodes )

S&F in repair diffuser plate

S&F in repair spray nozzle holder (Brass)

S&F in repair electrode connector (Brass)

S&F in repair electrode caps

S&F in repair solenoid valve

S&F in repair ignition transformer

S&F in repair burner cone (SS) for primary chamber burner

S&F in repair burner cone (SS) for secondary chamber burner

S&F in repair sequence controller

S&F in repair temperature indicator and controller for (TIC)

S&F in repair limit switch for charging door

S&F in repair wire rope 12mm dia for chimney support

S&F in repair fuel pump coupling with rubber spider

S&F in repair fuel filter assembly

S&F in repair water pressure switch

S&F in repair ID Fan bearing with connected items.

S&F in repair ID Fan blade with connected items bush, cater pin etc complete all as specified and directed by Engineer-in-charge..

M&L for repairing/ maintenance of ID Fan to chimeny rubber line duct / SS duct ( Dia 150 mm x 12 m long) including necessary cleaning and replacement of damaged / leakage SS Sheet with new SS sheet of same thickness all as specified and directed by Engineer-in-Charge. Note:- Contractor shall submit guarantee for duct repairing that if any leakage found same shall be rectified by him without any extra cost to Govt.

M&L for taking out / removing unserviceable venturi scrubber carefully by lifting the venturi scrubber and load the same in a suitable vehicle to transport to the Manufacturer's authorised workshop/ Lathe machine workshop and unloading the same for replacing the burnt / damage part complete and replace the same by newely constructed inner portion with MS sheet after repairing loading the venturi scrubber in suitable transport and unloading the same and install at site including carrying out necessary testing all as specified and directed by Engineer-in-Charge. Note:- (i) Burn / damaged portion shall be replaced with new MS sheet of suitable size & shape to match with existing venturi scrubbber. (ii) Thickness of MS sheet shall not be less than 5 mm (iii) Shape shall be round , square , flat as directed. (iv) Quoted rate shall be inclusive for necessary welding work, nuts,bolts , washer , insulating rubber and connected items as required.

M&L for repairing / improvement of door shutter of incinerator room installed at MH Mhow including providing hinges, nut, bolts, welding etc as required and cleaning, dusting, lubricating and applying two coats superior quality paint all as specified and directed.

M&L for Anti-climbing device; spikes type fabricated out of mild steel bars (round,square and flat) including nuts,bolts, washers and welding in two halves made to shape to suit the cross section of the pole complete all as specified and directed.

S.S. Engineers

Vinayak Trading House