Development and Upgradation of Batadrava Than at Barduwa, Nagaon for the

Amount

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m (A) Up to a depth of 2.00m below the existing ground level. All kinds of soil.

Extra for levelling & neatly dressing of disposed soil completely as directed by Engineer-in-charge.

Treatment of soil under existing floors using chemical emul sion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

Dry brick pitching half brick thick in drains including supply of bricks and preparing the surface complete (a) Brick on flat soling

Providing and laying in position ready mixed or site batched design mix cement concrete for plain cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana/Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering and finishing as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the minimum specified cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works upto plinth level : Concrete of M10 grade with minimum cement content of 220 kg /cum

Boring with hydraulic piling rigs with power units, providing and installing cast in situ single under reamed piles of specified diameter and length below pile cap in M-25 cement concrete, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and the length of the pile to be embedded in pile cap etc. all complete. (Length of pile for payment shall be measured upto to the bottom of pile cap) : 400 mm dia piles

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete

Suspended floors, roofs, landings, balconies and access platform

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Columns, Pillars, Piers, Abutments, Posts and Struts

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works upto plinth level Concrete of M25 grade with minimum cement content of 330 kg /cum

All works above plinth level upto floor V level Concrete of M25 grade with minimum cement content of 330 kg /cum

Add for using extra cement in the items of design mix over and above the specified cement content therein.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:4 (1 cement : 4 coarse sand) Supplying and filling in plinth with sand under floors, including watering,ramming, consolidating and dressing complete.

Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources)

Providing and laying autoclaved aerated cement blocks masonry with 100 mm thick AAC blocks in super structure above plinth level up to floor V level in cement mortar 1:4 (1 cement : 4 coarse sand ). The rate includes providing and placing in position 2 Nos 6 mm dia M.S. bars at every third course of masonry work

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). Sal wood

Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete 125x64x2.50 mm

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 250x10 mm

Providing and fixing bright finished brass door latch with necessary screws etc. complete 300x16x5 mm

Providing and fixing bright finished brass handles with screws etc. complete 125 mm

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.

15 mm cement plaster mix, inner side : 1:4 (1 cement: 4 coarse sand)

20 mm cement plaster of mix, rough side : 1:4 (1 cement: 4 coarse sand)

Steel work in built up tubular (round, square or rectangular hollow tubesv etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished seamless type tubes

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum moisture resistant board

Supply and fixing of VOX-infratop, False ceiling of panel sizes 340mm x 2700 mm, resistant to moisture & water. It is durable, scratch resistant EN 438-2 P-25, non flammable EN 13501-1 BS to fire C-S3:D0, in accordance with regulation (EU) no. 305/2011 under the sole responsibility of Manufacture. Increase the sound insulation EN ISO 140-4 EN ISO 717-1 of the room, thermal conduction EN 12664, UV resistance EN-ISO 4892-2 EN 20105-102, Global migration to food substance, No Emmission of Harmful substance.

Edge Profile 3050mm x 40 mm x 19 mm

Intemediate Profile, 3050mm x 76 mm x 12 mm

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement:4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily Glazed Vitrified tiles Matt/Antiskid finish of size Size of Tile 600 x 1200 mm

Providing and laying machine cut, mirror polished, Italian Marble stone flooring laid in required pattern in linear portion of the building all complete as per architectural drawings, with 18 mm thick stone slab laid over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with white cement slurry @ 4.4 kg/sqm including pointing with white cement slurry admixed with pigment to match the marble shade including rubbing, curing and polishing etc. all complete 18 mm thick Italian Marble stone slab, Perlato, Rosso verona, Fire Red or Dark Emperadore etc.

Providing and fixing 10 mm thick acid and/or alkali resistant tiles of approved make and colour using acid and/or alkali resisting mortar bedding, and joints filled with acid and/or alkali resisting cement as per IS : 4457, complete as per the direction of Engineer-in- Charge. In dado/skirting on 12 mm thick mortar 1:4 (1 acid proof cement : 4 coarse sand) Acid and alkali resistant tile

Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws Second class teak wood 35 mm thick

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately). Frame size 65 x 150 mm

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) 35 mm thick

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Distempering with oil bound washable distemper of approved brandand manufacture to give an even shade : In cement morter 1:4

Finishing walls with water proofing cement paint of required shade : New work (Two or more coats applied @ 3.84 kg/10 sqm)

Finishing walls with Acrylic Smooth exterior paint of required shade: New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete. On concrete work

Providing & fixing at all heights, levels and locations colour finish Aluminium alloy roofing sheets of alloy IS designation 31500, temper Hx8 conforming to IS 737 and dimensions as per IS code 2676 with characteristics of good formability and corrosion resistance. The profile sheets shall be fixed to truss members in slope or required pitch or curvature with Hex cap headed self drilling/tapping Stainless steel screws M6, 50 mm long with 3 mm EPDM seal washer etc. all inclusive of labour, scaffolding, T&P and sundries etc. complete as per directions of the Engineer-In-Charge. (Cost of truss/frame work shall be paid separately). 0.91mm Aluminium color coated profile with center to center pitch of 175 mm, depth of 46mm, top crest width of 41mm, bottom valley width of 80mm, overall profile width of 1144mm, cover width 1050mm.

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to openings /wooden frames with rawl plugs screws etc.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in charge, (for payment purpose only weight of tainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earthwith lead upto 50 metres. sqm 180.50

16.78 Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. 16.78.1 With material conforming to Grade-I (size range 75 mm to 0.075 mm) having CBR Value-30

With material conforming to Grade-II (size range 53 mm to 0.075 mm ) having CBR Value-25

Providing, laying, spreading and compacting graded stone aggregate (size range 53 mm to 0.075 mm ) to wet mix macadam (WMM) specification including premixing the material with water at OMC in for all leads & lifts, laying in uniform layers with mechanical paverfinisher in sub- base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achievethe desired density, complete as per specifications and directions of Engineer-in-Charge.

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 80 mm thick C.C. paver block of M-30 grade with approved color design and pattern.

Boundary wall with 1500 mm high wall and 600 mm High MS Grill including 2100 mm high stell gates at every 100 metres. With brickwork structure and RCC band at ground level and coping

Wiring for circuit/ submain wiring alongwith earth wire with the 2 x 1.5 sq. mm + 1 x 1.5 sq. mm of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.

Wiring for circuit/ submain wiring alongwith earth wire with the 2 x 2.5 sq. mm + 1 x 2.5 sq. mm of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit asrequired.

Wiring for circuit/ submain wiring alongwith earth wire with the 2 x 4 sq. mm + 1 x 4 sq. mm of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required.medium class PVC conduit as required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 5/6 A switch

2 way 5/6 A switch

15/16 A socket outlet

3 pin 5/6 A socket outlet

Telephone socket outlet(RJ-11)

Data socket outlet(RJ-45)

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required. 1 or 2 Module

3 Module

4 Module

6 Module

8 Module

12 Module

Supplying and fixing 12 Watt Down lights for common area including connection etc. as required.

Supplying and fixing 06 Watt Down lights for toilet including connection etc. as required.

Supplying and fixing 10 Watt LED batten light(Mirror light) including connection etc. as required.

Supplying and fixing 2x3 Watt Up Down lights including connection etc. as required.

Supplying & fixing LED bollard light including connection etc. as required.

Supplying & fixing Gate top light including connection etc. as required.

Supplying & fixing Wall light including connection etc. as required.

Supplying & fixing Spot light (projector series) including connection etc. as required.

Supplying & fixing ventilating fan 250mm including connection as required.

Supplying & fixing Hensel cable junction box(KF 1610 G)

Supplying & fixing Hensel cable junction box(KF 1006 G)

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.

Providing and fixing G.I. tape 40 mm X 6 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run)

Providing and fixing G.I. tape 40 mm X 6 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run)

Providing and fixing testing joint, made of 40 mm X 6 mm thick G.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required.

Supply, Installation testing & commissioning of floor mounted switching double door M V AMF PANEL duely powder coated with approved colour comprising of 1 x 400 A FP MCCB 36 kA as power incoming connected with 500A TPN cu basbar. Out going consisting of 6 x 100 A FP MCCB, 8 x 63 A TP MCB 10kA. 5 x 40 A MCB, controller based AMF change over, 1 x 160 A MCCB, 32 A with contactor and timer based street light feeder, Space for suitable 30 A energy meter as per govt. specification and a multi function meter also connected with the mains and bus for monitoring and energy billing complete in all respect. Standard fittings like indicator, spreader link, rotary handel, etc and double door should be considered.

Supply, Installation testing & commissioning of floor mounted 30 kVAr APFC PANEL

Supply, Installation testing & commissioning of wall mounted block panel as per design with 100 A FP MCCB incomer, 63 A, and 40 A outgoing as required.

Supply, Installation testing & commissioning of floor mounted FIRE PANEL consisting of the following ( 1No. 160A 36kA MCCB for Incomer, 2Nos 100HP Star-Delta Starter outgoing, 1No 15HP Star-Delta Starter outgoing with necessary Interlocking )

Supplying & installation testing and commissioning of MCCB/MCB distribution board Double Door/Single door (CONFORMING TO CPWD /NBC/ Relevant IS & BIS Code) a) VTPN DB 08 way

b) TPN DB 08 way

c) TPN DB 06 way

d) VTPN DB 04 way

e) SPN DB 16 way

Supplying, installation, testing & commissioning of Module case circuit breaker (CONFORMING TO CPWD /NBC/ Relevant IS & BIS Code) a) Four pole 100 Amps

Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. a) Double pole 25 Amps

Supplying, installation, testing & commissioning of Miniature circuit breaker (CONFORMING TO CPWD /NBC/ Relevant IS & BIS Code) a) Single pole 10 Amps

b) Single pole 16 Amps

c) Three pole 32 Amps

d) Four pole 63 Amps

Providing & laying 1.1 KV grade XLPE insulated aluminium armoured conductor cable on surface of the wall of building with required size of aluminium shadle and screw etc. as required. a) 3.5 Core 120 Sqmm Cable

b) 3.5 Core 50 Sqmm Cable

c) 3.5 Core 35 Sqmm Cable

d) 4 Core 16 Sqmm Cable

Providing & laying 1.1 KV grade XLPE insulated copper unarmoured conductor cable on surface of the wall of building with required size of aluminium shadle and screw etc. as required. a) 4 Core 4.0 Sqmm Cable(Un Ar)

b) 3 Core 4.0 Sqmm Cable(Un Ar)

c) 3 Core 2.5 Sqmm Cable(Un Ar)

d) 3 Core 1.5 Sqmm Cable(Un Ar)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. b) 3.5 Core 120 Sqmm Cable

c) 3.5 Core 50 Sqmm Cable

d) 3.5 Core 35 Sqmm Cable

f) 4 Core 16 Sqmm Cable

Termination of cable 3 core / 4 core armoured copper cable with required copper lugs and compression glands for each end complete in all respect including connection. a) 4 Core 4.0 Sqmm Cable(Un Ar)

b) 3 Core 4.0 Sqmm Cable(Un Ar)

c) 3 Core 2.5 Sqmm Cable(Un Ar)

d) 3 Core 1.5 Sqmm Cable(Un Ar)

Diesel generator set 160 KVA prime rating radiator cooled with alternator of 160 kVA output, 3 Phase, 415 V, 50 c/s 0.8 p. f. A.C a totally enclosed liquid cooled multi- cylinder (6/12) in-line 4 stroke, radiator cooled diesel engine developing suitable BHP at 1500 rpm, along with standard accessories, ƒBrushless type, Screen protected, Revolving field, Self excited alternator with static excitation system running at 1500 RPM. The DG Set shall be fitted with appropriate high end microprocessor-based controller for making it compatible for AMF system in the main medium voltage panel.

Supplying, Installation, testing and commissioning of 64Ch Digital NVR, Supports IP Cameras upto 12 Megapixels, All channel 4K resolution, 64 Channel Sync playback, 2 HDMI 1080p output, 64 Ch Audio and 1 mic in/out ports, 8 x 10 TB SATA, 2 USB, 1 RJ45 & 1, Incomming bandwidth support 300 MBPS & RS485 Ports and centralized video management system. product should be BIS approved, NDAA Compliant.

Supply, Installation, Testing & Commissioning of 5 MegaPixels Fixed Type Bullet Camera - 3.6mm Fixed Lens - H.265 Compression - Upto 30mtr IR - Triple Stream - IP65 / IK10 Rated - NDAA Compliant - InBuilt SD Card Slot

Supply, Installation, Testing & Commissioning of 5 MegaPixels Fixed Type Dome Camera - 2.8mm Fixed Lens - H.265 Compression - Upto 30mtr IR - Triple Stream - IP65 / IK10 Rated - NDAA Compliant - InBuilt SD Card Slot

8TB Survillance HDD, 7200RPM, Designed for 24/7 Usage.

HDMI Cable 15 MTR long.

55" LED DISPLAY FULL HD (4k DISPLAY)

6 core un-armoured multi mode optical fiber cable.

UTP CAT6A Cable (400 mtr)

Supplying, Installation , Testing and Commissioning of EPABX system equipped with 16 analog extensions , 4 CO Line having system features like-Programmable class of service for (STD/ISD/LOCAL) dialing as per need,Caller ID information for both internal and external callers ,Voice prompts ,Call forwarding,Brokers Call,Automatic call transfer,Conference call,Call pick up, etc.

Operator Console with DSS 40 keys, Speaker Phone.

Supply of Gsm Gateway 2 port To Provide redundent voice Link

Push Button Telephone Desk Phone with CLI.

Supplying, installation , testing and commissioning of 20 pair locking facility waterproof rectangle steel/PVC MDF Box with krone module having each krone connection slot have to accept upto wires of equal diameter complete as required.

10 Pair DP Box with Modules, expandable upto 20 Pairs

a) 2 Pair 0.5 mm sheathed telephone cable

b) 10 Pair jelley filled 0.50mm flexible telephone cable.

Enterprise Grade Inbuilt controler base Dual Band (2.4 & 5 GHz) Indoor Access Point :Proposed Access Point must be multifunctional high performance 802.11ac wave 1 or better.Must support 2x2 multiple-input multiple-output (MIMO).Must supports up to 1.2Gb/s wireless data rate and up to 64 simultaneous clients association in single Access Point.

Supplying & fixing 1 no RJ45 UTP CAT 6 outlet with 1 no, 1 module white plate & 1 no. 1 module metal flush (Legrand - Mosaic) including connection etc. as required.

L2 Full managed Ethernet stand alone chassis provides 24 PoE RJ-45 10/100/1000 BaseT, 1Gig BaseX combo and 2 SFP Gigabit uplinks ports. 1U by 1/2 rack form factor, internal AC power supply ( 370W PoE budget), fan less on 19" rack mount kit, power cord, manuals/software access cards, RJ-45 to DB-9 adaptors and rubber tabletop feet. (HP/CISCO/ALCATEL)

L2 Full managed Ethernet stand alone chassis provides 24 RJ-45 10/100/1000 BaseT, 1Gig BaseX combo and 4 SFP Gigabit uplinks ports. 1U by 1/2 rack form factor, internal AC power supply, fan less on 19" rack mount kit, power cord, manuals/software access cards, RJ-45 to DB-9 adaptors and rubber tabletop feet. (HP/ CISCO/ALCATEL)

24U Rack/800x1000/CKD/Castor T2/19" Adp/Perforated Doors/Side Panels, Horz. Cable Organiser Box Type, Shelf/1000, Shelf/Key Board/19"Rty/1000, Mounting Hardware-CR (Pack of 10), PDU 1Ph, 230V, 32A, 12 x 5/15A IRP 16A MCB x 2 Circuites - 7.3KVA, ITE / Server Rack Air Circulation module/Tower Mount/360CFM, Cable Basket/36U/100/NRS1

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: (a) White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete.

Supplying, installing and testing 8 mm dia CP health faucet of approved make with necessary CP flexible hose 1200 mm long, wall hook, with angular stop cock with wall flange, CP wall flange all of approved make etc.complete in all respect.

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- (a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required : (a)Range of two half stall urinals with 5 litre P.V.C. automatic flushing cistern

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : (a)Rectangular shape 453x357 mm

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board 510x1040 mm bowl depth 250 mm

Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour. Waste coupling 31 mm dia of 79 mm length and 62mm breadth weighing not less than 45 gms

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

Providing and fixing toilet paper holder :(a)C.P. brass

Supplying, fixing CP twin robe / coat hook fixed with SS screws on to the toilet door complete in all respect.

Supplying, fitting and fixing approved make Towel Ring fixed on to wall by using with SS screws in the pantrys. complete in all respect.

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931 15 mm nominal bore

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :15 mm nominal bore

Supplying, fixing and testing Multi Floor trap along with SS frame & cover (125 mm x 125 mm square / 100mm round). Trap of 100 mm dia. Inlet and 75 mm dia outlet fixed on a bed of cement concrete etc., complete in all respect. (The frame and grating shall be approved by Architects)

Supplying, installing, testing and commissioning of single lever high flow 3 way diverter, with exposed parts kit consisting of operating lever, wall flange (with seals) and overhead shower (150x150mm square shape) comprising of CP shower arm, with CP wall flanges etc. complete in all respect.

Supplying, fitting fixing and testing SWR soil and waste pipes confirming to IS 13592, type B solvent fit (confirming to IS 5382) joint inclusive of all necessary fittings like bends, tees, offsets, door bends, junctions, cowls, etc., laid under floor/ fixed on walls on G.I. brackets with GI 'U' clamps in pipe shafts etc., complete in all respect. INTERNAL a) 110 mm dia

b) 75 mm dia

Supplying, fitting fixing and testing SWR soil, waste pipes confirming to IS 13592 type B with rubber ring (confirming to IS 5382) with solvent joint inclusive of all necessary fittings like bends 45 or 90 degree, 'Y's, tees, offsets, door bends, junctions, screw type caps, vent cowl etc., fixed in the pipe shafts on pipe racks. complete in all respect. VERTICAL a) 75mm dia

a) 110mm dia

Supplying,fitting fixing and testing uPVC UV-R pressure pipe (6 Kg/ sq cm) confirming to IS 4985 : 2000 for waste connection from wash basin, kitchen sinks and urinal to floor trap/ anti syphonage pipe with solvent fit joints, including all the fittings, laid under floor/concealed in wall etc, the work shall include wall chase and making good the same in cement mortar etc, complete in all respect. b) 50 mm dia

Supplying, fitting fixing and testing SWR rain water pipes with all fittings like shoes, bends fixed in the pipe shafts (ducts) with suitable supports etc., complete in all respect. a) 160 mm dia - Type - A

Supplying and fixing of Roof corner outlet with khurra and grating for rain water outlets on terrace including all necessary grounting with sealants to make it absolutely water proof. a) 160mm dia

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. 20 mm nominal dia Pipes

25 mm nominal dia Pipes

Supplying, installing and testing approved make full way lever operated CPVC ball valves conforming to ASTM D 2846 with unions etc.Complete in all respect. a) 20 mm dia

a) 25 mm dia

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 20 mm nominal dia Pipes

25 mm nominal dia Pipes

32 mm nominal dia Pipes

40mm nominal dia Pipes

50 mm nominal dia Pipes

65 mm nominal dia Pipes

Supplying, installing and testing approved make full way lever operated CPVC ball valves conforming to ASTM D 2846 with unions etc.Complete in all respect. a) 20 mm dia

b) 25 mm dia

c) 32 mm dia

d) 40 mm dia

e) 50 mm dia

Supplying and fixing C.I. cover 300x300 mm without frame for gully trap (standard pattern) the weight of cover to be not less than 4.5 kg

Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality Rectangular shape 600x450 mm internal dimensions

Providing and constructing of Grease trap using 150mm thick burnt brick masonry walls built in CM 1:4 over PCC 1:4:8 bed , RCC cover slab, benching in CC 1:2:4 internal faces plastered smooth in CM 1:4, 15mm thick and outside exposed faces with cm 1:6 15mm thick including 600x600mm medium duty CI Manhole Frame & cover as shown in the drawings with necessary earth work excavation and backfilling and disposing surplus soil as directed by the Engineer in charge etc, complete in all respect. a) 450 x 450x 450 mm size internal .

b) 200 mm dia

Providing and placing on terrace high density polyethylene water storage tank with man hole lid and suitable locking arrangement including making holes for inlet, out let and ball cock including testing etc. all complete: (Sintex or equivalent) 2000 Itrs capacity

Providing, fixing, testing and commissioning of Water treatment plant 5 cm/ hr (Refer technical specification)

Supply of Factory assembled Compact self contained Hydropneumatic system (Refer technical specification)

Openwell Submersible, Centrifugal Type; With Motor-Base Frame-MOC-CI Base+ Discharge Manifold; Shaft - SS316. Flow- 15-20M3/Hr & Head 30-40 Mtrs.2 Nos. pump (1 working+1 standby), cascade operation, approx 5.5 KW each, Located under Treated Water Tank. Both the pumps shall be equal running hours for proper use controlled by intellegent control panel with all protection.

HEAT PUMP: Supplying, installing, testing and commissioning of Packaged type air to water Heat Pump. These units shall be completely factory assembled including the Rotary Scroll Compressor(s), Cooler, Condenser and Microprocessor Control Panel etc with R410A Refrigerant. The Heat Pump should be capable of operating at 53°C inlet and 58°C outlet hot water (condenser circuit) temperatures when evaporator outlet temperature is at 7 degree C inlet 12 degree C . The control of the system should be from the leaving hot water temperature set point. Primary Hot Water Circulation pump for heat pump of suitable capacity flow rate and head shall be incluided. Eurovent certified heat pump will be prefered.

Excavations for pipelines in trench and pit in open areas where disposal or surplus earth is done along the alignment, including trimming and dressing sides, leveling of beds of trenches to correct grades, cutting joint holes, refilling consolidation and dewatering of refilling in 15 cm layers & restoration & unmettalled or unpaved surface to it's original condition. The rate including the cost of necessary timbering dewatering of drain water, diversion of traffic, night signals, fixing caution boars, watching fencing etc. Upto 1.5m depth in all classes of soil

Supply, fabrication , laying, testing & commissioning of heavy grade IS marked & as approved make list black mild steel piping confirming to as per IS 1239/3589(Part 1) complete ( ‘C' class MS ERW pipe ) for undegound/ overground pipes with welded / flanged connection with saddles, supports (all with screwed/welded joints) as required including pipe of shorter lengths, tapering connecting pieces, short or long bends, specials like sockets, union nuts, elbows, reducers, plugs, Tees etc.Complete to make the system operative as required by LFA / TAC authorities the pipes will have to be laid and fixed in trenches. The work includes excavation in all types of soils and back filling, dewatering, etc., making holes in brick or RCC walls, slabs/ roofs and making good the damages by bringing to the original condition to the satisfaction of the Architect and painting two coats of approved shade(Post office red)of enamel paint over a coat of approved primer for over heads pipes and providing and fixing pypkote (corrosion protection tape) including supply and application of pipe coating and spiral Wrapping for underground piping (wrapping should have overlap of 15 to 20 mm)etc.complete as per ASTM standards/IS:10221 for corrosion protection of pipes for the under ground installation. Note : The piping installation has to be put to hydraulic test to 1.5 times the working pressure & as per latest applicable codes & standard before applying paint or pipe coating or wrapping etc. complete. 150 mm NB 5.4 mm thick and 21.3 Kg. wt. / mtr. Approx.(UNDER GROUND).

80 mm NB 4.8 mm thick and 9.9 Kg. wt./ mtr. Approx.(UNDER GROUND).

80 mm NB 4.8 mm thick and 9.9 Kg. wt./ mtr. Approx.(ABOVE GROUND).

Providing and fixing hydrant stand posts of 80 mm dia. With flanges and accessories and supply, fixing single headed 63 mm dia 2.1/2” NB S.S. Hydrant Valve in the courtyard as per IS:5290, TAC / LFA approved & ISI certified heavy type hydraulically tested to 1.5 times working pressure with necessary nuts, bolts etc. Including 2 coats of approved enamel paint (red) over a coat of primer,complete with ‘Morris’ pattern instaneous couplings, etc. complete in all respect. 63 mm Single S.S headed Hydrant

Providing & fixing 63mm dia RRL hose pipe as per IS 636 TYPE A TAC/ LFA approved of 15 mtr. standard length of approved pattern and size including S.S male and female Coupling duly bound with copper wire etc. complete in all respect. 63 mm RRL Hose 15mtr.length.

Providing and fixing TAC approved fire hose cabinet to house fire hydrant & hose, including all other related accerrories fabricated from M.S. sheet (16 Gauge) of fully welded construction having front door with locking arrangement, partially glazed with 4 mm thick glass. Cabinet shall be powder coated & painted with post office red colour of size as mentioned in drawing (or as approved by the Architect) to house 15 mtr.x2 nos. hoses. The hose box size is 750 mm x 600 mm x 250 mm complete in all respect. Hose Cabinet for External yard Hydrant

Providing and fixing S.S branch pipe nozzle conforming to IS : 903, suitable for instantaneous connections to hose coupling etc. as required: S.S Branch Pipe

Providing, installing, testing & commisioning of fire brigade inlet connection (fire department connection) consisting of 2 Nos. 63 mm dia instantaneous inlet arranged on a 150 mm dia header, 1 No. 150 mm diameter sluice valve, 1 No. 150mm dia. C.I Non-return valve , the above mentioned components. It should be complete (Connected with rigment )

Providing, installing, testing & commisioning of fire brigade draw out connection (fire department connection) with suction pipe MS class 'C' 100 mm dia. & 100 mm dia. foot valve & steel chain including wall mounted box M.S. construction made out of 16 gauge MS Sheet with glass door to house the above mentioned componenets. It should be complete as per manufacturer's (to be connected to static water tank)

Supply, erection, testing & commissioning of ISI MARKED SLUICE VALVE conforming to IS: 14846. PN-1.6 with companion flanges, gaskets & nuts and bolts. 150 mm DIA

Supplying & installation, completely testing with perfect alignment and proper leveling and commissioning of fire service main pump for wet riser Hydrant system.The pump should be single stage, foot mounted , horizontal centrifugal End Suction Back Pull out type design, (electrical driven) for hydrant main / sprinkler with cast iron casing & bronze impeller & internal parts, EN-8 / C-40 shaft, directly coupled to totally enclosed fan cooled (TEFC) squirrel cage A.C. induction motor of suitable capacity to operate on 3 ph. 440 V 50Hz. A.C.2900 RPM Syn. speed with ‘B’ class winding, ‘F’ class insulation & IP 55 Protection.The coupling guard in an approved manner have to be supplied and must be fitted on the set properly as approved by TAC/CFO for fire duty. Both the pump and motor are to be fitted on common M.S. base frame fabricated with required size of M.S. channel. The pump set should be erected on suitable rigid foundation tighten with the help of foundation bolts ,nuts & washers, capable of discharging 2280 LPM against 60 mtr. head against all losses complete. The pump shall be capable of giving not less than 150% discharge at a head not less than 65% of the rated head. Shut off head should not exceed 120% of the rated head. Motor to be of continuous rating etc. complete. Pump - Motor : Discharge : 2280 LPM, Head 60 mtr

Supply, installation, testing and commissioning of Diesel Engine driven fire pump suitable for automatic operation comprising of the following : Horizontally mounted end suction centrifugal pump, suitable for operation on 415 volts ± 10%, 3 phase, 50 HZ A.C supply, complete with flexible coupling and coupling guard as required. Fire pump having C.I. body, bronze impeller and S.S. Shaft with mechanical seal, capable for delivering 2280 LPM of water at 60 mts. head to ensure a minimum pressure of 3.5.kg/cm2 at the terrace/farthest hydrant. Complete with necessary pressure gauge with gun metal shut off cock on delivery side. The pump should meet the condition of Local fire Authority/NBC). Water Cooled Diesel engine of speed 1800 RPM for the above pump with automatic starting mechanism (AMF autostart panel complete with necessary relays like no volt relay, over voltage and low voltage relays, contactors, timer, pressure switch etc. as required for the auto start of the diesel engine in case of power failure complete with all accessories, wiring & cabling) and other accessories including fuel tank (fabricated from 3mm MS sheet painting with two coats of synthetic enamel paint over a coat of primer) capacity 600 Its (fitted with Magnetic oil level indicator, MH with cover drain valve, Air vent hydraulic pumps including structural supports (painted with approved shade), 2 Nos. x 12 volt battery, heat exchanger with necessary piping connections & fittings flexible coupling, coupling guard & exhaust pipe ( 150 mm diameter M.S. Class 'B' diesel pump exhaust pipe includings all fittings, like bends, tees etc. clamps / structural steel supports. The pipe shall be provided with 75mm thick fiberglass insulation & covering the insulation with 500 g polythene sheet giving proper overlaps & sealing the joints with suitable adhesive compound. The pipe shall be provided with 24 gauge aluminium sheet cladding.) as per drawing complete as required. Common base plate for above pump and Diesel Engine from M.S. channel of required size. Suitable PCC/RCC foundation with plaster, Antivibration arrangement of cushy foot mountings. 24 volts, 180 AH Lead battery ( 12 volts-2 Nos) with boost / trickle charger for starting the engine automatically as required. FIRE PUMPS - DIESEL : Discharge :2280 LPM, Head 60 mtr

Supplying, installing, completely testing with perfect alignment and proper leveling and commissioning of centrifugal end suction type jockey pump-motor having bronze impeller for wet riser Hydrant system, The pump should be single stage, foot mounted, horizontal centrifugal Vertical Multistage, Back Pull out type design. The pump must be T.A.C. (Tariff Advisory Committee) Approved having discharge capacity of 10.8 LPM (Liters/min.) against 60 mtr. head with 3 phase, 415 V, 50 Hz motor having 2900 RPM, The pump must be having CI Casing, bronze impeller, Bronze working parts, EN-8 / C-40 shaft, directly coupled to totally enclosed fan cooled (TEFC) squirrel cage A.C. induction motor of suitable capacity to operate on 3 ph. 440 V 50Hz. A.C. with ‘F’ class insulation & IP 55 Protection. Both the pump and motor are to be fitted on common M.S. base plate fabricated with required size of M.S. channel. The pump set should be erected on suitable rigid foundation tighten with the help of foundation bolts ,nuts & washers, The coupling guard in an approved manner have to be supplied and must be fitted on the set properly as per site conditions and instructions of site engineer-in-charge including proper fixing, The electrical motor for the pump should be capable to operate at run out zone and comply as per Specification etc. complete. Pump - Motor : Discharge :10.8 LPM, Head : 60 mtr.

Supplying, installation testing and commissioning of the following Supply, fabrication , laying, testing & commissioning of heavy grade IS marked & as approved make list black mild steel piping confirming to as per IS 1239/3589(Part 1) complete ( ‘B' class MS ERW pipe ) for over ground pipes with welded / flanged / screwed joints and with heavy clamps, hangers, brackets or pipe supports (all with screwed/welded joints) as required including MS pipe of shorter lengths, tapering connecting pieces, short or long bends, forged specials like sockets, union nuts, elbows, reducers, plugs, tees, bends etc. complete to make the system operative as required by LFA / TAC authorities. The pipes will have to be laid and fixed on walls, ceilings, into brick walls or RCC with lead anchor fastners.The work includes making holes in brick or RCC walls, slabs/ roofs and making good the damages by bringing to the original condition to the satisfaction of the Architect/Consultant/Client and painting two coats of approved shade (Post office red) of enamel paint over a coat of approved primer for over ground / overheads pipes. Note : The piping installation has to be put to hydraulic test to1.5 times the working pressure (for minimum 2 hrs.) before applying paint or pipe coating and wrapping etc. Complete 200 mm NB 10 mm thick and 51.59 Kg. wt./ mtr. Approx.

150 mm NB 5.4 mm thick and 21.3 Kg. wt. / mtr. Approx.

100 mm NB 5.4 mm thick and 14.5 Kg. wt./ mtr. Approx.

80 mm NB 4.8 mm thick and 9.9 Kg.wt./ mtr. Approx.

65 mm NB 4.5 mm thick and 7.93 Kg.wt./ mtr. Approx.

25 mm NB 4 mm thick and 2.93 Kg. wt./mtr. Approx.

Supply, erection, testing & commissioning of ISI MARKED SLUICE VALVE conforming to IS: 14846. PN-1.6 with companion flanges, gaskets & nuts and bolts. Size: 200 mm NB

Size 150 mm NB

Size: 100 mm NB

Size: 80 mm NB

Supply, erection, testing & commissioning of ISI MARKED GATE VALVE conforming to IS: 14846. PN-1.6 with companion flanges, gaskets & nuts and bolts. Size: 150 mm NB

Size : 65 mm NB

Supply, Instaallation, testing & commisssioning of swinging type Dual plate CI Non return Valve as per IS:5312(PN16 rating) with disc and SS hinges complete including matching flanges, nuts & bolts complete. Size: 150 mm NB

Size : 65 mm NB

Installation of Pressure switches, SPDT type, of suitable range for pump sets with ball valves and other accessories. Pressure Switch (TR-Model )

Supply, erection, testing and commissioning of PRESSURE GAUGE as per tender specification. The scale shall be in metric units. Accuracy shall be 1.0 percent of full-scale range or better conforming to IS: 3624-1979. Pressure Gauge : 0- 16 kg/sq.cm.

Supply, erection, testing & commissioning of SUCTION STRAINER with companion flanges, gaskets & nuts and bolts. 200 NB

Supply, erection, testing & commissioning of SUCTION Y-STRAINER with companion flanges, gaskets & nuts and bolts. 150 NB

Supply, installation, testing & commissioning of Rubber bellows on discharge side of pump conforming to EJMA with all hardwares, companion flanges & gaskets, etc. Size : 150 mm

Size : 65 mm

SITC of elctronic type water level indicator with LED panel, with probe & all control wiring to operate the system automatic/manual & shll prevent the pump from dry running

Supply, erection, testing & commissioning of 4 Kg ABC (Powder Type) Fire Extinguisher. In HP Mild Steel Cylinders ISI marked fitted with pressure indicating gauge, internal discharge tube, squeeze lever type valve, discharged nozzle, suspension bracket, conforming to IS: 15683 duly charged with ABC powder (Mono Ammonium Phosphate) conforming to IS: 14609 and pressured by Nitrogen suitable for operating .on 30⁰C to + 55⁰C. (4 years maintenance free) complete in all respect.

Supply, erection, testing & commissioning of 4.5 Kg. Cap. CO2 type Fire Extinguisher (ISI marked) complete with tube horn etc.(ISI marked), handle , fixing bracket & other accessories.

Supply, erection, testing & commissioning of 9.0 litrs. Cap. Mechanical Foam Fire Extinguisher (IS: 10204 / 15397) complete with CO2 cartridge GM cap, ½ meter discharge tube & nozzle (ISI marked), handle , fixing bracket & other accessories.

STP/ETP Plant of 10 KLD

SHREE GAUTAM CONSTRUCTION CO. LTD.