SPECIAL REPAIR TO BLDG NO 236 IN VIKRAM VIHAR UNDER GE SOUTH, DELHI CANTT-10

M & L for Providing and injecting chemical Imidacloprid emulsifiable concentrate for Post Constructional Anti termite Treatment Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron.

M & L for Anti termiteTreatment of soil under existing floors using chemical Imidacloprid emulsifiable concentrate @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 to match the existing floors all as specified .

Demolition of reinforced cement concrete of any description and in any position not otherwise specially provided for including cutting of reinforcement to facilitate demolition (Parapet wall) complete all as specified and directed.

M&L for reinforced cement concrete (Design mix) M-25 (20 mm graded stone aggregate) as in fins, slab ,fascias, louvres, parapets, and railings, newels, balustrade, and the like complete.

S&F TMT bars 10 mm dia & over as in reinforcement of columns, beams, RCC, slabs, chajjas, lintels etc cut to length bent to shape required including cranking, bending, spirally hoping for columns, hooking ends and welding the new reinforcement with old steel bars complete.

S&F 8mm dia TMT bars, cut to length bent to shape required including cranking bending spirally for hoping for columns, chajjas to parapets etc hooking ends and binding with mild steel wire not less than 0.90mm dia complete.

M&L Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc.

M&L for chipping out spilled and loose concrete cover and derusting steel reinforcement of concrete column, beam, slab, chajjas, parapets and the like as directed up to 25 to 35mm thick roughening and cleaning concrete surface with steel wire brushes, washed with water and allowed to dry including derusting steel wire reinforcement, providing fabric MS wire mesh 75 x 75 x 2mm as reinforcement to concrete surface applying adhesive/admixture over steel mesh and providing 25mm average thickness guniting mix using one part of OPC 53 grade and two part of sand mixed with adhesive/admixture @ pressure of 2.5 to 3.00kg/Sqcm by guiniting machine and surface finished even and fair including necessary padding, shuttering/scaffolding, formwork (guniting work to be carried out up to 10 metre height) complete as directed at site Note :- (a) After placing the additional reinforcement all concrete surfaces shall be thoroughly scrubbed with wire brushes, washed with water and allow to dry, apply chemistic polycretes admixture @ 2.25 kg by weight of cement all as per manufacturers instruction. (b) when polymix concreting in taking condition,guiniting is done with polycrete admixture @ 2% by weight of cement all as per manufacturers instructions (polycrete admixture shall be procured from chemical adhesive Pvt Ltd Co or their authorised dealer). (c) Cost of the above aspect shall be deemed to be included in the quoted rate of the respective item and nothing extra shall be paid on any account.

Demolition of brick work built in cement or cement lime mortar complete all as specified and directed.

M&L for old size Brick work with sub class "B" bricks , straight or curved on plan exc 6 m mean radius built in cement mortar (1:6),(up to two story Bldg) complete all as specified.

M & L for Dismantling of brick tiles (laid flat or on edge) on roof surface.laid bedded and pointed in any mortar

M & L for Demolition of mud in roof, any thickness, including plastering and leeping upto two storey bldg incl necessary scaffolding arrangement complete all as specified and directed(whether full thickness removed or only a part there of) and removing from cantonment area or as directed complete all as directed by Engr in charge and specified.

M&L for Cement concrete type B-0, 1:2:4 (12.5mm graded aggregate) as in roof pedding , finished even and smooth without using extra cement ,including cleaning the concrete surface by steel wire brushes, up to three stories bldgs, complete .

Roof Treatment (Complete System) This item covers complete waterproofing treatment on roof in stages: (i) Surface Preparation Cleaning concrete roof surface using wire brush. Removing dust, loose particles, etc. (ii) PCC for Slope PCC B-0 (1:2:4) with 12.5 mm aggregate. Used to maintain slope on roof. Mixed with liquid waterproofing compound. (iii) Cement Rendering 15 mm thick plaster in CM 1:3 on roof, chajja, parapet, sunken areas, etc. (iv) Waterproofing Compound Supply of liquid waterproofing compound only as directed by Engineer-in-Charge. (v) PU Primer Single-component solvent-based polyurethane primer. Applied by brush/roller. Minimum coverage 200 ml per sqm. Penetrates pores of concrete. (vi) PU Waterproofing Coats Two coats of PU (polyurethane) waterproofing. Non-UV resistant. Applied at 4–6 hours interval.60 GSM non-woven geotextile embedded between coats. Technical requirements: Thickness: 1.20 mm Tensile strength ≥ 1.80 N/mm² Elongation ≥ 650% Crack bridging ≥ 1.50 mm ASTM standards to be followed. (vii) Separation / Protection Layer 150 GSM non-woven geotextile. Overlap minimum 75 mm. Protects waterproofing system. (viii) SRI Coating (Heat Reflective)

S & F for Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on and including 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface up to 3 cuts complete, including providing skirting up to 150 mm height along the parapet walls in the same manner.

M & L for Providing cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate in roof kerbs or mud stops, rounded or chamfered and hold fast on edge including necessary form work complete as directed.

Demolition of stone slab and tiles of any description or thickness on cooking platform, floors, aprons, skirting etc laid bedded and pointed in any morter complete all as specified and directed

M & L for Granite (of any type) work, 18-20 mm thk (table rubbed and polished) in steps, jambs, pillars, cooking platforms, skirtings with necessary hole for gas pipe where ever required and likes on cement mortar bedding of 20mm thick in CM 1:4 including pointing in white cement using marble dust with admixture of pigment to match including rounded edges with shade of granite complete all as specified and directed.

M&L for Udaipur green marble work 18 to 20mm thick (table rubbed and polished) in steps, riser/skirting, jambs, pillars, window cills, and like including including 20mm thick screed bed in CM 1:4 and pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade and including Non-slip system for treads ( 03 Nos groves ) complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises

M & L for Glazed Ceramic coloured tiles in vertical surface 600X300X7 to 8 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match and including 10mm thick backing coat of cement mortar (1:3), with adhesive type - II (wall) thickness as per manufacturing instructions complete all as specified and as directed. complete all as specified and directed

M&L for Vitrified Ceramic tiles light shade 10 mm thick (square/rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm of size (600mm X 1200mm), in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete including 20 mm thick rendering in cement mortar (1:4) with adhesive type - II (Floor) thickness as per manufacturing instructions complete all as specified and as directed.

All as per item No -22 but as in skirting including 10 mm thick backing coat CM 1:3 all as specified and directed.

M&L Non Skid ceramic tiles 8 to 10 mm thick (square/rectangular) area of each tile 600 x 600 mm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including screed bed or bedding layer of mortar 15mm thick in CM 1:4 with adhesive type - II (Floor) thickness as per manufacturing instructions complete all as specified and directed.

M&L Non skid coloured ceramic tiles 7 to 8 mm thick ( square / rectangular) area of each tile exceeding 0.11 sqm but n exc 0.18 sqm, as in skirting laid on 10 mm thick cement plaster in CM (1:3), set and jointed in neat cement slurry with adhesive type - II (Floor) thickness as per manufacturing instructions in coloured cement to match the shade of tiles.

S&F in repair Vitreous china wash down water closet pan sinlge piece syphonic action , white fixed in repair,including soft close sheet cover of closed pattern with flat bottom complete. Cat part No Hindware 20121 or equivalent including dual flushing cistern viterous china 10 ltr capacity complete all as specified.

S & F Vitreous china squatting pan ‘Orissa’ pattern, size 580 x 440 mm, coloured, with integral foot rests, fixed in repairs including provision of lime concrete bedding complete.Squatting pan including connection to trap, and to flushing pipe, anti-syphonage pipe, etc. complete including making good to floor complete.

S&F in repairs low level flushing cistern of 10 ltrs capacity PVC valveless, syphonic action type, white with inlet ball valve float and handle complete all as specified.

S&F in repair CP brass health faucet with hand shower and 1.5 mtr flexible stainless steel pipe suitable for fixing to 15 mm dia pipe complete.

S & F in repair Toilet paper holder of mild steel Chromium plated ‘D’ type, fixed in repairs to walls with chromium plated brass screws complete.

S & F in repair Vitreous china wash basin with pedestal white, flat back, size 550 x 400mm, including necessary waste pipe and coupling, brackets and cutting for and pinning in ends of brackets, complete.

S&F in repairs elegent mirror PVC cabinet without towel rail of size 422 x 622 mm all as specified.

S&F in repairs stainless steel foldable towel rack 60 cm long and 24 cm deep with towel rail and hangers at bottom fixed to walls complete all as specified and directed.

S&F in repairs brass chromium plated shower rose of size 125 mm with long arms (300 to 450 mm ) including fixing to CPVC.

S&F in repairs 6 mm thick glass corner shelf fancy type with railing and fitting complete of size 25cm x 25 cm of best quality (as per sample approved by Engr -in-charge)

S&F in repairs wash hand basin mixer single lever 15mm dia CP brass fancy type including joints to CPVC pipe or unions all as specified.

S & F in repairs Brass CP Wall mixer(Non Telephonic Type) with L bend 3-in-1 for mixing hot & cold water screwed down for CPVC pipe 15 mm bore and fixed complete all as specified.

S&F in repairs Kitchen sink mixer 15mm dia CP brass fancy type including joints to CPVC pipe or unions all as specified.

S&F in repairs 15 mm bib tap, brass chromium plated fancy type (quarter turn), long body screwed down including necessary extention piece complete.

S&F in repair 15 mm dia brass chromium plated angle valve fancy type (quarter turn), screwed at ends including necessary extention piece and fixed complete.

S&F in repairs Good quality Connecton pipe (PVC) 15 mm dia and 450/600mm long complete all as specified.

Taking down (Door) chowkats or frames with shutters not exceeding 1.5 Sqm each (without taking off shutters from the frames) complete.

Taking down (Door) chowkats or frames with shutters exceeding 1.5 Sqm but not exceeding 4.00 Sqm each (without taking off shutters from the frames) complete.

S&F Factory Made single extruded WPC (Wood Polymer Composite) Solid door/window/Ceosetory windows & other frames/ chowkat of size 65x 125 mm comprising of virgin PVC polymer of K value 50-60 (Suspension Grade), calcium carbonate and natural fibers( wood powder/ rice husk/ wheat husk) and non toxic additives ( max toxicityindex of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face & 1100 N Edge), min compressive strength of 58N/sqmm and resistance to flame of class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixed with MS Holdfast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engr in charge.Note: For WPC solid door/windows frames,minus 5mm tolerance in dimension i.e depth and width of profile dimension on plus side shall be acceptable but no extra payment on this account shall be made.

S&F factory made single extruded WPC (Wood Polymer Composite) solid door/window/ceosetory windows & other frames/chowkhat of size 65 x100 mm comprising of vigin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ricehusk/wheat husk) and non toxicadditives (maximum toxicity index of 12 for 100 g,s) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. .(MS hold fast/hugs or SS dash fasteners shall be paid for separately) Note:- For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 35mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and nontoxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, including 0.8 mm thick PVC strips all around, fixed to factory manufactured WPC shutter to ensure the colour of strip as per frame and shutter, complete all as per direction of EngineerIn- Charge. (Note: stainless steel butt hinges shall be paid separately under relevant item).

Providing 30mm thick FACTORY-MADE WIRE MESH SOLID WPC DOOR SHUTTER consisting of Density 650 Kg /Cbm Manufactured by an ISO-9001-2015 certified Company, Door to be panelled with SS moquito Mesh and XTN aluminium Mesh for additional strength and safety purpose. (Confirming as per IS:4020). including 0.8 mm thick PVC strips all around, fixed to factory manufactured WPC shutter to ensure the colour of strip as per frame and shutter. The door should be water proof, termite proof,fire retardant and having screw holding capacity. Door to be fixed to frame with 3 nos. SS butt hinges size 100mm*25mm*2mm and 32mm long steel screws drilled suitable to pass through Other hardwares shouldbe fixed with 19*6mm size steel screws etc. Complete as per direction of Engineer-in-charge, manufacturer's specification & drawings.” Note: Fixture/fittings shall be measured & paid under relevant item

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and nontoxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, including 0.8 mm thick PVC strips all around, fixed to factory manufactured WPC shutter to ensure the colour of strip as per frame and shutter all as per direction of EngineerIn- Charge. Note: stainless steel butt hinges shall be paid separately under relevant item).

S&F Factory Made single extruded WPC (Wood Polymer Composite) Solid door/window/Ceosetory windows & other frames/ chowkat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers( wood powder/ rice husk/ wheat husk) and nontoxic additives ( max toxicityindex of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face & 1100 N Edge), min compressive strength of 58N/sqmm and resistance to flame of class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixed with MS Holdfast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engr in charge. Note: -For WPC solid door/windows frames, minus 5mm tolerance in dimension i.e., depth and width of profile dimension on plus side shall be acceptable but no extra payment on this account shall be made.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter for cupboard of size 19 mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and nontoxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of EngineerIn- Charge. Note: stainless steel butt hinges shall be paid separately under relevant item).

S&F incuding fabricating as per existing pattern with 50 mm dia Stainless steel (SS 304 grade) hand railing with 25 mm dia balusters, steps including buffling with Stainless steel bowl complste all as specified and directed including taking down old wooden stair case railing.

S&F 5 mm thick toughned glassfixed with uPVC windows including all necessary fittings. Complete all as specified and as directed.

S & F in repair for mild steel, 300 mm ordinary rat tail rod pattern springs including roller and roller plate complete all as specified.

M & L for preparation of old Steel surfaces of any description not otherwise described over 10 cms width or girth and apply one coats of synthetic enamel paint all as specified.

S&F 100mm long (size) butt hinges, stainless steel AISI 304 grade with brass/bronze hinge pin complete

S&F stainless steel AISI 304 grade barrel tower bolt 200mm long, extruded section,etc. complete all as specified and directed.

S&F stainless steel AISI 304 grade handle of size 200mm long,etc. complete all as specified and directed.

S&F Stainless steel of AE SI 304 Grade, sliding door bolt 300mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts & sliding bolts of extruded sections or cast aluminium alloy complete.

S&F Magic eye and fixed to doors all as specified and directed complete.

S & F Hasp and staple -100 mm size, safety type, aluminium anodised including bolt to hinge plate, fixed with screws complete.

S & F Floor door stopper (double leg) of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor; overall length of cover plate 150mm complete.

S&F in repair 25 mm dia SS curtain rod , 1.25 mm heavy duty type thick of sheet with fixing brackets, side knobsof good quality as approved complete all as directed.

Demolition of cement concrete (unreinforced) in ground floors and paving not exceeding 15cm thickness (below or above ground level) complete.

M & L for Cement concrete 1:3:6 type C1 using 20mm graded stone aggregate in plinth protection, 75mm thick, finished fair and even without using extra cement, complete.

Forming Construction joint 30mm deep x 10mm wide filled with sealing compound grade 'A'

Taking up or down steel tubing and connections all as specified.

(a) 15 mm bore

(b) 20 mm bore

Supplying and laying of CPVC 20mm OD pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors incl brass coupling fittings complete all as specified complete with fitting as required.

Supplying and laying of CPVC 25 mm OD pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors incl brass coupling fittings complete all as specified complete with fitting as required.

S&F 20mm outer dia CPVC Union complete all as specified and directed.

S&F 25mm outer dia CPVC Union complete all as specified and directed.

S&F 25mm outer dia CPVC Tank Adaptor complete all as specified and directed.

S&F 20mm outer dia CPVC Tank Adaptor complete all as specified and directed.

S&F 25mm outer dia CPVC ball valve/gate valve complete all as specified and directed

S&F 20mm outer dia CPVC ball valve/gate valve complete all as specified and directed

S&F 20mm outer dia CPVC Brass Elbow complete all as specified and directed.

S&F 20mm outer dia CPVC Male Brass Threaded Adapter (MTA/BTA) complete all as specified and directed

S&F 25mm outer dia CPVC Male Brass Threaded Adapter (MTA/BTA) complete all as specified and directed

S&F 20 mm outer dia CPVC Brass Tee complete all as specified and directed

Dismantling water tanks of capacity exceeding 500 litres but not exceeding 1000 litres complete.

Dismantling water tanks of capacity exceeding 250 litres but not exceeding 500 litres complete.

S&F 500 ltr capacity rotational moulded triple layered polyethylene water storage tanks (cylindrical vertical with closed top) white colour hoisted and fixed in position all as specified.

S&F 1000 ltr capacity rotational moulded four layered polyethylene water storage tanks (cylindrical vertical with closed top) white colour hoisted and fixed in position all as specified.

S & F in repairs Gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe 20 mm bore complete.

S & F in repairs Gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe 25 mm bore complete.

S & F in repairs Sinks with drainage board made of 1mm thick stainless steel for kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including supply & fixing cantilever brackets of mild steel angle 35 x 35 x 5 mm and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm, including PVC waste pipe 32 mm bore, 65 cm long complete.

S&F sinks made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or includingfixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm.

Dismantling of cast iron or reinforced concrete drains pipes , jointed in cement morter and taking out of trenches if required up to 100 mm internal dia of drains, complete all as specified and directed.

S&F 110 mm uPVC pipes Type 'B' (for waste water), single socketed, in any length with rubber ring joints, laid in trenches or in floors or fixed to walls complete all as specified and directed.

S&F 75 mm uPVC pipes Type 'B' (for waste water), single socketed, in any length with rubber ring joints, laid in trenches or in floors or fixed to walls complete all as specified and directed.

Taking down eaves gutters and rain water pipes (any size, material or pattern), including all fittings , heads, shoes, bends,swann necks, etc including taking out of trenches if required for cleaning or refixing or removal to store complete all as specified.

S&F 110 mm uPVC pipes Type 'A' (for rain water), single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and directed.

S&F 110 mm uPVC (SWR) Bends/ Tees/ Tapers (any radius), with or without oval access door as required complete all as specified and directed.

S&F in repairs uPVC multi floor trap with gratings including jointing with solvent cement, dia of out let 75 mm complete all as specified and directed

S&F 75 mm uPVC (SWR) Bends/ Tees/ Tapers (any radius), with or without oval access door as required complete all as specified and directed.

S & F Stack clamps out of 50mm x 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof, for any bore and any type of pipes complete.

Taking down cement or cement lime plaster, any description, on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water etc including removal of debrish from the MOD land complete all as specified and directed.

Expose the first joint of masonry structure at ground level horizontally. The plaster must be knocked off at least 50 cm beyond the visibly penetrated area. Damaged mortar joints are to be scraped out to a depth of approximately 2-3 cm. Drilling Holes : Drilling holes 10mm diameter in masonary structure along the side of the joint as per manufacturer's instructions so as to cross the brick/ block at the intervals spacing of 15-30cm depending on extent of rising dampness as per recommendation of engineer in charge. Cleaning of holes : Clean the holes by air blower prior to fixing nozzles. Install latex polymer packer injection packers 9.8mm diameter, 10cm long in the holes and tighten. Fix the packer securely using sealent. Cutting of Packers : Cut the packers after completion of grouting without damaging structural elements.

Supply and apply of a 3 part, very low viscous, elastic polyacrylic injection resin with a versatile and adjustable reaction time having Mixed viscosity : 3-11 M.pa.s at +20 Deg C, Reaction time : adjustable according to ambient temperatrure and execution requirement between 8-50 mins, pH – 9-10, tested as per Wissbau No. 2002-094-(1A) – Function test with re-injectible hose system. The holes should be drilled until a depth of approx 5 cm (for a 6cm thick wall) before the end of the wall is reached. Pump injcection of polymer resin compound at >20 bar into or behind fissures or into masonry joint which are allowing water to infiltrate into unwanted areas. If voids in masonry being injected contain insufficient moisture to activate the grout inject a small amount of water prior to injecting the grout. When movement stops or polymer compound appears at the packer move to the next packer and inject. If the dampness is heavy, inject similarly at next joint line (on average 200 ml for each hole, total 600 nos hole for 04 block)

M&L for 15 mm thick (self curing) ready mix plaster on external wall surfaces complete all as specified and directed.

M&L for 10 mm thick (self curing) ready mix plaster on internal wall surfaces complete all as specified and directed.

M&L for 5 mm thick (self curing) ready mix plaster on ceiling surfaces complete all as specified and directed.

M&L for preparation of the newly plastered surfaces of walls/ceiling applying wall care putty of 1 mm thickness over plastered surface to prepare the surface even and smooth to receive primer and applying one coat primer & two or more coats Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification.

M&L for preparation of old decorated surface (plastered or unplastered) of walls/ceiling by complete removal of existing treatment by mechanical grinder and applying water proof wall care putty of 1 mm thickness over plastered surface to prepare the surface even and smooth to receive primer and applying one coat primer & two or more coats Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification.

M&L for preparation of newly plastered surfaces of walls and providing and applying putty of 1 mm thickness over plastered surface to prepare the surface even and smooth and finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified as directed by Engr-in-charge.

M&L for preparation of old decorated plastered surfaces of walls, complete removal of existing treatment by rubbing , brooming down, washing with water etc and providing and applying plaster of Paris putty of 1 mm thickness over plastered surface to prepare the surface even and smooth and finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified as directed by Engr-in-charge.

Dismantling boarding, any description, fixed in any position with nails.

S&F Factory Made 19 mm thick 100% Solid WPC ( Wood polymer Composite ) Plain Board of required size comprising of virgin PVC resin of K Value 57-60 ( Suspension Grade ), Calcium Carbonate and natural Fibers ( Wood Powders/ rice husk/ wheat husk ) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded ( Inner ) with density not less than 650 kg/cbm Certified Company, having good screw holding capacity ( Screw Withdrawal strength of 2000 N ( Face ) & 1100 N ( Edge ), Minimum Compressive Strength of 50 N/mm2, Modulus of elasticity 850N/mm2 and resistance of spread of flame of Class A category with Property of being Termite/ Borer Free.Water/ Moisture Proof, Fire Retardant and fixing with stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws. All as per direction of Engineer -In-Charge, Material test certificate and authentication should be compulsory provided by the manufacturing company

S&F Factory Made 19 mm thick 100% Solid WPC ( Wood polymer Composite ) Laminated Board (both side) of required size comprising of virgin PVC resin of K Value 57-60 ( Suspension Grade ), Calcium Carbonate and natural fibers ( Wood Powders/ rice husk/ wheat husk ) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded ( Inner ) with having minimum density not less than 650 kg/cbm having good screw holding capacity ( Screw Withdrawal strength of 2000 N ( Face ) & 1100 N ( Edge ), Minimum Compissive of 50 N/mm2 , Modulus of elasticity 850N/mm2 and esistance of spread of flame of Class A category with Property of being Termite/ Borer Free.Water/ Moisture Proof and Fire Retardant. WPC to be Laminated with PVC foil of minimum 14 microns thick of approved design pasted on both faces of shutter and fixinng stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws. All as per direction of Engineer -In-Charge, Material test certificate and authentication should be compulsory provided by the manufacturing company.

S & F CP clip on hinges (Inset) complete all as specified and directed .

S&F 15mm mild steel, chromium plated rod with fixing brackets, fixed in cupboards for hanging cloth of adequate strength all as specified and directed.

S&F stainless steel AISI 304 grade handle of size 100 mm long,etc. complete all as specified and directed.

S&F aluminium powder coated G type profile handle for kitchen cabinet all as specified and directed.

S&F Magnetic catch for wooden cupbord with complete closer macanigum claps and clips fix with stainless steel screw.complete all as specified and as directed.

M&L for cleaning the sides Box hinges for Garage door of frame and shutters shafts guide channel and greasing of moving parts and straightening opening and closing and replacement of bolts nuts etc as required for smooth functioning of shutters and taking out existing shutters if required and refixing the same in original position complete all as specified (opening of shutter exc 2.00 m and not exc 3.50 m and area exc 6.00 sqm and n.exc 9.00 sqm all as specified)

S& F in repairs mild steel box type hinges of approved make in existing shutters/opening of shutters exc 2.00 m and n.exc 3.5 m all as specified.

Chipping of unsound/weak concrete/ plaster material upto 25mm average thickness from slabs, beams, coloums, wall etc with manual chiesel and/ or standard power driven percession type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc and disposal of debris for all lead and lifts all complete as per direction of Engineer-in-Charge

Providing, mixing and applying over reinforcement bars zinc anti rust agent as per specification and direction of Engineer-in-Charge (Dosage/ coverage as per the recommendation of manufacturer). Surface area of concrete shall be measured for payment.

Providing, mixing and applying apoxy bonding cost of approved adheslve on chipped portion of plaster as per manufacturers specifications and direction of Enginee-In-Charge complete in all respects including carriage of materials in all leads and lifts.

Supplying and providing non matallic composite corbon fiber low Modulas Precured CFRP Strip of 100mm wide and 1.4mm thick applied as per manufacturing instrution including surface preparation by Grinding/ moulding concrete, cleaning it with wire brush, removing oil, laitance etc.

Providing, mixing and apllying SBR polymer(of appprove make ) modified cement mortar in proportion of 1:4 (1 cement ratio 4 graded coarse sand with polymer min 2% by wt of cement used) as per specification and direction of Engineer-In-Charge. Note: Mesuarement and payment : the pre measurement of thickness shall be done only after proper wet curing has been done surface has been done satisfactorily evluated by sounding/tapping up to 25mm

S& F staianless plate rack made of 1 mm thick stainless steel sheet of size 750 mm x 900 mm x 210mm consisting of 3 shelf for bowls and one shelf for keeping six nos of big utensil and seven nos of small utensils divided by 10 mm dia stainless steel hollow pipe @ 60 mm centre to centre or as per drg and sample kept in GE"s office all as specified and directed by engr-in-charge complete.

S&F in repair stainless steel telescope channel of size 300 mm to 500mm complete all as specified and directed.

S & F Semi Modular Cabinet Kitchen accessories of Stainless Steel grade-304,6mm size rod thickness including :- (i) Perforated Cutlery basket, (ii) Grain trolley, (iii) Thali basket, (iv) Cup & saucer basket, (v) Glass basket, (vi) Plate basket, (vii) Premium magic corner (viii) Oil Pull out Tray ( Triple basket layer) , (ix) Dust bin, (x) Cleaning kit rack of size as per site requirement all spd and directed

S&F in repairs PVC Kitchen cabinet mirror of size 450 mm x 550 mm, made of high - quality PVC material, with front mirror shutter, internal storge shelves and magnetic catch. The cabinet shall be wall mouted with necessary ss screws and hardware, complete in all respects as specified and directed by Engineer - in- Charge.

Providing & fixing false ceiling at sufficent heights with GRG (Glass Fibre With Semi With fully Reinforced Gypsum) false ceiling tiles of perforated perforated 12mm Size 595 x 595 mm of approved texture, 12mm thick thick micro tegular design and patterns having moisture micro tegular edged or 10 mm content less than 2%, humidity resistance edged GRG thick square edged of 99%, NRC0.50 to 0.75 as per IS false ceiling GRG false ceiling 8225:1987, Noncombustible as per BS tiles tiles 4 76 (part 4 )-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on interlocking metal T-Grid of hot dipped galvanized iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of mainT runners of size 15 x 32 mm of length 3000mm,cross-T of size 15x 32mm of length 1200mm and secondary intermediate cross-T of size 15 x 32 mm of length 600mm to form grid module of s1ze 600x 600mm , suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per sqm) i.e 50mm long, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1 OOOmm length and L shape level adjuster of size 85x25x2mm. Galvanised iron perimeter wall angle of size 24x 24x0.40mm of length 3000 mm to be fixed on periphery wall I partition with the help of plastic rawl plugs at 450 mm center to center and 40mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in Charge.

Demolition of cement concrete in above ground floors exc 15 cm thick above ground floors.

M&L for applying a coat of cement slurry @ 0.488 Kg/Sqm mixed with tapercreate @ 0.253 Kg/Sqm after cleaning and drying the old/new surfaces(Make of tapercreate M/S CICO Engg Services) then applying the layer of fibre glass cloth while the above coat is still green. The overlap of fibre glass cloth shall be not less than 100 mm.(Make of fibre glass cloth M/S The Structure Water Proofing Co Pvt Ltd) and then applying 1.5 mm thick layer @ 1.288 Kg/Sqm mixed with taper create @ 0.570 Kg/Sqm and coarse sand @ 1.289 Kg/Sqm. Allow the treatment to air curing for four hours followed by water curing for 48 hours all as directed.

M&L for 10 mm thick cement plaster on brick/ concrete surface in CM 1:3, finished even and fair surface with out using extra cement but mixing water proofing compound at the rate of 2% of cement by weight (WPC shall be paid separately).

M&L Cement concrete Type E2 (1:5:10) using 40 mm graded stone aggregate in mass concrete in sunken floor complete all as specified.

M&L 75 mm thick PCC type D2 (1:4:8) using 40 mm graded stone aggregate as in sub base of flooring.

M&L for 25mm thick cement concrete type B-0 1:2:4 (12.5mm graded aggregate) as in sub floors finished rough.

Demolition of cement concrete (unreiforced) in ground floors and pavings not exceeding 15 cm thickness (below and above grounf level) complete.

M&L 100 mm thick cement concrete type C-2 (1:3:6) using 40 mm graded stone aggregate as in sub base of flooring.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks,lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand all as specified and directed.

M&L Providing Precast cement concrete Type B:1 1:2:4 (20 mm graded stone aggregate) as in kerb stone set in cement mortar 1:4 complete all as specified and directed.

Taking down carefully aluminium/copper point wiring (light/fan/bell/socket /power) with complete fittings such as steel terminal boxes, switches, ceiling roses, pendents, regulators, sockets etc and removing the material including making good the distrubed surfaces of the wall flooring ceiling etc to match the existing surface all as specified and directed by Engr-in-Charge.

M&L for concealed point wiring complete with stranded copper conductor 1.5 Sqmm nominal area PVC insulated FRLS 1100 volts grade electrical cable drawn through existing concealed PVC conduit in wall and ceiling including replacement of unserviceable pressed steel terminal boxes with Modular steel terminal boxes factory made having min 1.2 mm thickness including white cover modular plate with frame suitable for modular switches, modular sockets, modular fan regulators etc of required size complete including 1.5 sqmm copper cable earth continuity wire to common earth and connected to earth dolly complete all as specified for One light/Fan/Bell point controlled by one 5 Amp switch one way using cable (1.5 Sq mm for phase and neutral and 1.5 sqmm for earthing) . Note :- The rate is inclusive cutting/chasing and making good disturbed surface with CM 1:3 and same surface finishs with the adjoining surface of disturbed area with OBD/Colour wash/white wash complete.

All as per item No 2 above but 5 Amp socket outlet on same board.

All as per item Srl item No.141 here in before, but for one three pin socket outlet 6 amps point controlled by one no, one way switch on independent board and through new concealed conduit complete.

All as Item No 141 above but for one socket outlet 5/15 Amps on Independent board with cables 2.5 sqmm size for phase and neutral and 2.5 Sqmm for earthing complete.

All as per Srl No.141 above One light point controlled by 2 way switch with 1.5 Sqmm conductor.

M&L for concealed point wiring complete with stranded copper conductor 4 Sqmm nominal area PVC insulated FRLS 1100 volts grade electrical cable drawn through concealed PVC conduit complete including 4 sqmm copper cable earth continuity wire to common earth and connected to earth dolly complete all as specified for one socket outlet for modular AC Box on Independent board with cables 4.0 sqmm size for phase and neutral and 4 Sqmm for earthing complete. . Note:- the rate is inclusive cutting /chasing and making good the disturbed surface with cm 1:3 and same surface finishes with the adjoining surface of disturbed area with OBD/colour wash/white wash complete

S&F switch modular type, 1 way 10A, 1module IP-20 white colour complete all as specified and directed by Engineer in Charge.

S&F Modular Shuttered Socket, 6A - 2/3 pin 2 module IP-20 white colour complete all as specified and directed by Engineer in Charge.

S&F switch modular type 1way 16A, 1module with indicator IP-20 white colour complete all as specified and directed by Engineer in Charge.

S&F Modular shuttered Socket 6/16A - 2/3 pin combined IP-20 white colour complete all as specified and directed by Engineer in Charge.

S&F Modular Bell push 10A 1 Module with nidicator IP-20 white colour complete all as specified and directed by Engineer in Charge.

S & F Switch Modular type switch, 10 A 2- way 1 Module IP-20 white colour complete all as specified and directed by Engineer in Charge.

S & F in replacement ,Decorative wall light mounting suitable for LED Lamp upto 15 Watt complete with all connections all as specified and directed.

S&F in replacement Surface mounting round shaped LED downlighter with durable housing with aluminium pressure die- cast with heat heat dissipating fins diffuser to give glare free light 12 Watt LED 6000K/6500K lamp type from ceiling of stairs/common areas, complete all as directed.

S&F in replacement Wall mounted LED Integrated Batten 20 Watt - 4Ft White,CRI 80, aluminium housing, 120 Lumens per watt,6500K(cool White)4000 K (Natural White), Pf < 0.90 indoor LED battern IP-40 complete all as specified and directed by Engr in Charge.

S&F in replacement Wall mounted LED Integrated Batten 10 Watt - 2Ft White,CRI 80, aluminium housing, 120 Lumens per watt,6500K(cool White)4000 K (Natural White), Pf < 0.90 indoor LED battern complete all as specified and directed by Engr in Charge.

S&F Modular AC Box with socket and MCB SP 20 Amp complete with Metal box , white colour plate and frame complete in replacement of sheet metal enclosures as per site requirement , complete all as specified and directed.

S&F LED bulb 12 Watt, CRI 80, Frosted glass, 3000k white 100 Lumens/watt Pf <0.90, Min 25000 Hr IP rating 20 complete all as specified and directed.

S&F of electric bell Ding Dong type AC, 230 volts single phase all as specified.

S&F ceiling rose surface Bakelite 65x25mm two to three terminals complete all as specified.

S&F in replacement LED bulk head in engineering plastic housing with clear prismatic diffuser, 10W WHITE in replacement of old unsv bulk head fitting including all accessories connecting up twin core flexible copper conductor cable complete all as directed.

S & F LED lamp 9W LED lamp suitable for B-22 holder complete all as specified and directed

Taking down of existing ceiling fan deposited to E/M store yard and refixing the same after completion of B/R repair works all as specified and bt Engr-In- Charge.

Supply and fix exhaust fan made of sturdy engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, copper winding motor and sweep 250 mm CMH 750-800 and connecting up with replacement of cable T/C flexible cable of size:- 1.50 Sqmm from ceiling rose / connection to fan and taking out fan and deposited to E/M store yard all as specified and directed.

Taking Down of existing Geyser any type any size including disconnection of electrical connection and water connection complete all as directed.

Supply & fixing of water storage heater Sqaure type, 5 star, remote operation, Anti bacterial sterilization, Digital temperature settings, Performance based Heat Tech, Temperature Sensor, Dry Heating Protection, Glass lined enamel coated incoloy heating element , Feather touch buttons, Shock resistant injection moulded ABS body, waterproof technology, Tank design is suitable to withstand 8 bar pressure, PRCD, ECO function, Whirl Flow Technology, Error code display (Geyser) of capacity 25 litre ISI mark,AC, electric, 415 volt, complete , 3 core lead, including safety valve, including electric and water connection and making good to disturbed surface complete all as specified and directed. Make: Jaquar/ Vector of Venus Aquerra DG/ Usha. (Note : (i) Electric switch for geyser of 16 Amps switch & switch board shall be provided at near bathroom door and 16 Amp socket outlet shall be provided near the geyser and will be measured as 16 amps power wiring against item no.5

S&F in replacement of sheet metal enclosures double door for DBs when MCBs to be used SPN-08 Way,with rubber gasket 240V complete as per site requirement and as directed by Engr-in charge.

S&F in replacement of sheet metal enclosures double door with rubber gasket for DBs when MCBs to be used SPN-12 Way, 240V complete as per site requirement and as directed by Engr-in charge.

S&F in replacement of sheet metal enclosures double door for DBs when MCBs to be used SPN-4 Way, 240V complete as per site requirement and as directed by Engr-in charge.

S&F in replacement MCB SPN 63 Amps 'B' series, breaking capacity 10 Ka, 'B' curve 240 volts, 50 Hz including necessary incoming and out going electric connection with suitable size of copper lugs etc.

S&F in replacement MCB SPN 40 Amps 'B' series, breaking capacity 10 Ka, 'B' curve 240 volts, 50 Hz including necessary incoming and out going electric connection with suitable size of copper lugs etc.

S&F for MCB SP 6 to 32 Amps 240 Volts, 10kA, `B' curve all as per site requirement and as directed

M&L for earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edge of the plate not less than 1.5 M below normal ground level connected to GI wire 4 mm as earthing lead by means of nut, bolts and check nuts and washers, GI light grade protection pipe 15 mm dia upto 7.5 M, GI watering pipe 20 mm dia medium grade, RCC cover with funnel, excavation in any type of soil, PCC pit charcoal, salt all as shown in electrical plate No 5 of SSR Part I, including earth test point upto panel board, all as specified directed.

Taking down unserviceable sub main wiring twin core of any size complete and making good disturbed surface complete all as specified and directed.

M&L for Sub Main wiring using single run PVC FRLS grade Insulated unsheathed, multistrand copper conductor cable 2 runs of 10 Sqmm for phase and neutral and 1 run of 10 Sqmm for earth wire drawn through concealed PVC conduit wiring in wall not less than 25mm dia with all fittings like tees, bends, junction/ terminal boxes etc as per site requirement and all as directed by Engr-in-charge. (Note:- Phase should be of Red /Yellow/Blue, neutral should be of back and earthing wire should be of green colour. 2 runs of cable for phase/ neutral and 1 run for earth will be measured and paid as one unit length).

S&F wall mounted fully auto clean domestic type Electric chimney in size range from 60 cm to 90 cm hood for 2-3 gas burners of suction capacity 700-1200 m³/Hr with touch control, filterless chimny No need to clean filters, easy to clean oil collector tray , 100% copper wound motor, environment-friendly 1.5 W LED lamp, 5 years warranty on motor including all connecting accessories,fitting and fixtures all as specified and directed by engr-in -charge .Note:- work for fitting of chimney including hole of suitable size for outlet will be done by contractor without any extra cost.

Supply and fix wall mounted fan made of sturdy Engineering plastic complete voltage 230V, 50 Hz, Copper winding of sweep 400mm all as specified and directed by engr in charge.

Taking down the existing exhaust fan from kitchen and deposited to E/M store yard and including the closer of holes across the wall with B/R finising work complete all as specified and directed by Engr-in-charge.

Supply and fixing of PVC conduit medium grade of size 15mm TV connection and Socket /Telephone socket complte all as specified and directed by engr in charge.

Supply and fixing TV Co-Axial Socket 1 module all as specified and directed by engr in charge.

Supply and fixing Telephone socket 1 module all as specified and directed by engr in charge.

Supply and fixing Flush metal box 1 module all as specified and directed by engr in charge.

Supply and fixing white cover plate with frame 1 module all as specified and directed by engr in charge.

S & F Modular fan regulator 120 W 2 module complete all as specified and directed.

Supply & fixing of water storage heater, 5 star rated with Marine grade glass line coating Tank Efficient long life copper heating element ,Adjustable Thermostat, Shock resistant amd rust proof engineering thermoplatic body, IPX4 waterproof technology, Tank design is suitable to withstand 8 bar pressure (Geyser) of capacity 06 litre ISI mark, , AC, electric, 415 volt, complete , 3 core lead, including safety valve, including electric and water connection complete all as specified and directed by Engr in charge. (Note : (i) Electric switch & socket for geyser of 16 Amps shall be provided in the Kitchen near the geyser and will be measured as 16 amps power wiring against item no.5