REPAIR MAINT OF CERTAIN SUB STN LT PANELS APFC PANELS AVR GLOW SIGN BOARDS RECTIFIER POINTS TARMAC PANELS UG CABLES AND ALLIED WORKS AT TECH AREA DOMESTIC AREA AND AFS UNDER GE AF JORHAT

Amount

S&F of cubical housing cabinet type LT panel board OUT door type, platform mounted factory made, totally enclosed dust and vermin proof openable from both front and rear side made out of 14 SWG (3.15mm) thick CRCA MS Sheet of overall size 1000mm (height) x 1000 mm(width) x 450 mm (depth) and built upon suitable size angle iron frame work , having front and rear hinged doors,GI earthing strips at rear side , bottom detachable gland plate complete with suitable size zinc plated and passivated nut, bolts , spring and washers. The cabinet and all members should be chemically treated with MSR solution for anticorrosive treatment and apply powder coated paint (RAL-7032) The panel should be suitable for 415 volts , 50Hz, 3 phase 4 wire system and internal connection should be provided with aluminium strips of suitable size and necessary foundation work and comprising following:-

BUS BAR CHAMBER:- (a) Sheet steel bus bar chamber having front hinged covers with a set of electrolytic grade high conductivity TP&N solid aluminium bus bars, rated 500 amps supported at required intervals sleeved with heat shrinkable PVC sleevings. The bars shall be colour coded at required intervals for identification - SET OF 4, 1 No.

INCOMER:- (a) MCCB of 4 pole of capacity 250 amps with breaking capacity of 35KA - 1 Nos. OUTGOING FEEDERS:- (a) MCCB of 4 pole of capacity 160 amps with breaking capacity of 36KA - 01 Nos. (b) MCCB 4Pole of capacity 100 amps with breaking capacity of 36KA -02 No.

S&F of cubical housing cabinet type LT panel board OUT door type, platform mounted factory made, totally enclosed dust and vermin proof openable from both front and rear side made out of 14 SWG (3.15mm) thick CRCA MS Sheet of overall size 1000mm (height) x 1000 mm(width) x 450 mm (depth) and built upon suitable size angle iron frame work , having front and rear hinged doors,GI earthing strips at rear side , bottom detachable gland plate complete with suitable size zinc plated and passivated nut, bolts , spring and washers. The cabinet and all members should be chemically treated with MSR solution for anticorrosive treatment and apply powder coated paint (RAL-7032) The panel should be suitable for 415 volts , 50Hz, 3 phase 4 wire system and internal connection should be provided with aluminium strips of suitable size and necessary foundation work and comprising following:-

BUS BAR CHAMBER:- (a) Sheet steel bus bar chamber having front hinged covers with a set of electrolytic grade high conductivity TP&N solid aluminium bus bars, rated 500 amps supported at required intervals sleeved with heat shrinkable PVC sleevings. The bars shall be colour coded at required intervals for identification - SET OF 4, 1 No.

INCOMER:- (a) MCCB of 4 pole of capacity 250 amps with breaking capacity of 35KA - 1 Nos. OUTGOING FEEDERS:- (a) MCCB of 4 pole of capacity 125 amps with breaking capacity of 36KA - 01 Nos. (b) MCCB 4Pole of capacity 63 amps with breaking capacity of 36KA -02 No.

S&F of cubical housing cabinet type LT panel board OUT door type, platform mounted factory made, totally enclosed dust and vermin proof openable from both front and rear side made out of 14 SWG (3.15mm) thick CRCA MS Sheet of overall size 1000mm (height) x 1000 mm(width) x 450 mm (depth) and built upon suitable size angle iron frame work , having front and rear hinged doors,GI earthing strips at rear side , bottom detachable gland plate complete with suitable size zinc plated and passivated nut, bolts , spring and washers. The cabinet and all members should be chemically treated with MSR solution for anticorrosive treatment and apply powder coated paint (RAL-7032) The panel should be suitable for 415 volts , 50Hz, 3 phase 4 wire system and internal connection should be provided with aluminium strips of suitable size and necessary foundation work and comprising following:-

BUS BAR CHAMBER:- (a) Sheet steel bus bar chamber having front hinged covers with a set of electrolytic grade high conductivity TP&N solid aluminium bus bars, rated 300 amps supported at required intervals sleeved with heat shrinkable PVC sleevings. The bars shall be colour coded at required intervals for identification - SET OF 4, 1 No.

INCOMER:- (a) MCCB of 4 pole of capacity 160 amps with breaking capacity of 35KA - 1 Nos. OUTGOING FEEDERS:- (a) MCCB of 4 pole of capacity 100 amps with breaking capacity of 36KA - 01 Nos. (b) MCCB 4 pole of capacity 63 amps with breaking capacity of 36KA -02 No.

S&F of cubical housing cabinet type LT panel board OUT door type, platform mounted factory made, totally enclosed dust and vermin proof openable from both front and rear side made out of 14 SWG (3.15mm) thick CRCA MS Sheet of overall size 1200mm (height) x 1200 mm(width) x 450 mm (depth) and built upon suitable size angle iron frame work , having front and rear hinged doors,GI earthing strips at rear side , bottom detachable gland plate complete with suitable size zinc plated and passivated nut, bolts , spring and washers. The cabinet and all members should be chemically treated with MSR solution for anticorrosive treatment and apply powder coated paint (RAL-7032) The panel should be suitable for 415 volts , 50Hz, 3 phase 4 wire system and internal connection should be provided with aluminium strips of suitable size and necessary foundation work and comprising following:-

BUS BAR CHAMBER:- (a) Sheet steel bus bar chamber having front hinged covers with a set of electrolytic grade high conductivity TP&N solid aluminium bus bars, rated 600 amps supported at required intervals sleeved with heat shrinkable PVC sleevings. The bars shall be colour coded at required intervals for identification - SET OF 4, 1 No.

INCOMER:- (a) MCCB of 4 pole of capacity 315 amps with breaking capacity of 35KA - 1 Nos. OUTGOING FEEDERS:- (a) MCCB of 4 pole of capacity 160 amps with breaking capacity of 36KA - 01 Nos. (b) MCCB 4 pole of capacity 125 amps with breaking capacity of 36KA -02 No. (c) MCCB 4 pole of capacity 100 amps with breaking capacity of 36KA -02 No.

Trimming of tree branches, girth not exc. 100mm, to clear OH line upto 2.0 metre on each side, stacking the branches where directed to a distance not exc. 50 metre and clearing the site, complete all as specified and directed.

Cutting of grasses / vegetations, earth heaps etc. manually or grass cutter cleaning and levelling surroundings at E/M installations including removal of spoil, wastage materials etc. complete all as spcified and directed.

M&L for complete disconnecting APFC panel from all incoming / outgong connection of any capacity, checking the serviceability of all components i.e existing capacitors, contactors, MCB's, MCCB, indicator lights, power factor controller, replacement of burnt out PVC insulated copper wire, copper thimble, MCB's SPN C Series (6-25Amp) and re-connect the same after thoroughly clean and testing complete all as specified and directed at site. Note:- items such as Capacitors, contactors, MCCB and power factor controller etc.shall be measured and paid separately as supply only under relevant items here-in-after.

Supply only Heavy duty Resin filled capacitor 440 volt, 3 phase 50 Hz of capacity 5 KVAR complete all as specified and directed. Make : L&T/ Legrand/ Havells

Supply only Heavy duty Resin filled capacitor 440 volt, 3 phase 50 Hz of capacity 7.5 KVAR complete all as specified and directed. Make : L&T/ Legrand/ Havells

Supply only Heavy duty Resin filled capacitor 440 volt, 3 phase 50 Hz of capacity 10 KVAR complete all as specified and directed. Make : L&T/ Legrand/ Havells

Supply only Heavy duty Resin filled capacitor 440 volt, 3 phase 50 Hz of capacity 12.5 KVAR complete all as specified and directed. Make : L&T/ Legrand/ Havells

Supply only Heavy duty Resin filled capacitor 440 volt, 3 phase 50 Hz of capacity 15 KVAR complete all as specified and directed. Make : L&T/ Legrand/ Havells

Supply only Heavy duty Resin filled capacitor 440 volt, 3 phase 50 Hz of capacity 20 KVAR complete all as specified and directed. Make : L&T/ Legrand/ Havells

Supply only capacitor duty contactors Type MOC5 for 5 KVAR rating @ 415 Volt 3 phase (including 1 NO + 1 NC) complete all as specified and directed. Make : L&T/ Legrand/ Havells

Supply only capacitor duty contactors Type MOC10 for 10 KVAR rating @ 415 Volt 3 phase (including 1 NO + 1 NC) complete all as specified and directed. Make : L&T/ Legrand/ Havells

Supply only capacitor duty contactors Type MOC12.5 for 12.5 KVAR rating @ 415 Volt 3 phase (including 1 NO + 1 NC) complete all as specified and directed. Make : L&T/ Legrand/ Havells

Supply only power factor controller of capacity 8 Step 440 volt, 3 phase 50 Hz. complete all as specified and directed. Make: L&T/ Legrand/ Havells

S & F in repair MCCB 4 pole, 415 Volts, 63 Amps with breaking capacity 36 KA (Adjustable Thermal Magnetic Release Setting) complete all as specified and directed. Make - Legrand Cat Part No 420093 or equivalent in ABB/Havells/L&T

S & F in repair MCCB 4 pole, 415 Volts, 100 Amps with breaking capacity 36 KA (Adjustable Thermal Magnetic Release Setting) complete all as specified and directed. Make - Legrand Cat Part No 420095 or equivalent in ABB/Havells/L&T

S & F in repair MCCB 4 pole, 415 Volts, 125 Amps with breaking capacity 125 KA (Adjustable Thermal Magnetic Release Setting) complete all as specified and directed. Make - Legrand Cat Part No 420096 or equivalent in ABB/Havells/L&T

S & F in repair MCCB 4 pole, 415 Volts , 160 Amps with breaking capacity 36 KA (Adjustable Thermal Magnetic Release Setting) complete all as specified and directed. Make : Legrand Cat Part No 420097 or equivalent in ABB/Havells/L&T

S & F in repair MCCB 4 pole, 415 Volts, 200 Amps with breaking capacity 36 KA (Adjustable Thermal Magnetic Release Setting) complete all as specified and directed. Make - Legrand Cat Part No 420248 or equivalent in ABB/Havells/L&T

Supply and fixing in repair MCCB 4 pole, 415 Volts , 400 Amps with breaking capacity 36 KA (Adjustable Thermal Magnetic Release Setting) complete all as specified and directed. Make - Legrand Cat Part No 422007 or equivalent in ABB/Havells/L&T

Supply and fixing in repair street light panel, 3-phase / 230V with Digital 24 Hr time switch, Contactor Rating 65 Amps, MCB Rating 63 Amps TP including iron frame of suitable size for fixing the panel and all accessories complete all as specified and directed. Make : Indoasian Cat Part No TL 065AB0 / Havells/ Legrand

S&F in repair MCB TPN, 63 Amps ('C' curve) capacity, 10KA 415 Volts including cable connection with copper lugs complete all as specified and directed. Make : Legrand Cat Part No 408683 or equivalent in ABB/Havells/L&T

Repair / Maint and overhauling of ACB of capacity 800Amp/ 1000 Amp in existing position after disconecting the LT conections, open the outer cover,racking out , checking out spring charge motor, triping and closing coil, overhauling the complete unit by cleaning with suitable cleaning materials and replacement of minor spares, internal electrical wiring and electronic accessories and insulated properly complete all as specified and directed.

Repair / Maint and overhauling of Servo Voltage stabilizer of capacity 10 KVA in existing position after disconecting the LT conections, open the outer cover, taking out coil, overhauling the complete unit by cleaning with suitable cleaning materials and replacement of minor spares such as fuse, diod, carbon brushs, holder, internal electrical wiring and electronic accessories and insulated properly by varnishing, greasing, CRC spraying complete all as specified and directed. Note: Spare parts shall be measured and paid as supply only under respective items here-in-after.

Supply only servo controller motor for 10 KVA Servo Voltage Stabilizer, complete all as specified and directed.

Supply only Cummutator plug of existing size for 10 KVA Servo Voltage Stabilizer, complete all as specified and directed.

Supply only Brush Arm of existing size for 10 KVA Servo Voltage Stabilizer, complete all as specified and directed.

Supply only Slip ring of existing size for 10 KVA Servo Voltage Stabilizer, complete all as specified and directed.

Supply only PCB Card for 10 KVA Servo Voltage Stabilizer, complete all as specified and directed.

Supply only Relay for 10 KVA Servo Voltage Stabilizer, complete all as specified and directed.

Repair / Maint and overhauling of Servo Voltage stabilizer of capacity 100 KVA from existing position after disconecting the LT conections, open the outer cover, taking out coil, overhauling the complete unit by cleaning with suitable cleaning materials and replacement of minor spares such as fuse, diod, carbon brushs, holder, internal electrical wiring and electronic accessories and insulated properly by varnishing, greasing, CRC spraying complete all as specified and directed. Note: Spare parts shall be measured and paid as supply only under respective items here-in-after.

Supply only servo controller motor for 100 KVA Servo Voltage Stabilizer, complete all as specified and directed.

Supply only Cummutatior plug of existing size for 100 KVA Servo Voltage Stabilizer, complete all as specified and directed.

Supply only Brush Arm of existing size for 100 KVA Servo Voltage Stabilizer, complete all as specified and directed.

Supply only PCB Card for 100 KVA Servo Voltage Stabilizer, complete all as specified and directed.

Supply only Relay for 100 KVA Servo Voltage Stabilizer, complete all as specified and directed.

Repair / Maint and overhauling of Servo Voltage stabilizer of capacity 150 KVA from existing position after disconecting the LT conections, open the outer cover, taking out coil, overhauling the complete unit by cleaning with suitable cleaning materials and replacement of minor spares such as fuse, diod, carbon brushs, holder, internal electrical wiring and electronic accessories and insulated properly by varnishing, greasing, CRC spraying complete all as specified and directed. Note: Spare parts to be measured and paid as supply only under respective items here-in-after.

Supply only servo controller motor for 150 KVA Servo Voltage Stabilizer, complete all as specified and directed.

Supply only Cummutatior plug of existing size for 150 KVA Servo Voltage Stabilizer, complete all as specified and directed.

Supply only Brush Arm of existing size for 150 KVA Servo Voltage Stabilizer, complete all as specified and directed.

Supply only Slip ring of existing size for 150 KVA Servo Voltage Stabilizer, complete all as specified and directed.

Supply only Relay for 150 KVA Servo Voltage Stabilizer, complete all as specified and directed.

Repair / maint and overhauling of Servo Voltage stabilizer of capacity 750 KVA from existing position after disconecting the LT conections, open the outer cover, taking out coil, overhauling the complete unit by cleaning with suitable cleaning materials and replacement of minor spares such as fuse, diod, carbon brushs, holder, internal electrical wiring and electronic accessories and insulated properly by varnishing, greasing, CRC spraying complete all as specified and directed. Note: Spare parts to be measured and paid as supply only under respective items here-in-after.

Supply only servo controller motor for 750 KVA Servo Voltage Stabilizer, complete all as specified and directed.

Supply only Cummutatior plug of existing size for 750 KVA Servo Voltage Stabilizer, complete all as specified and directed.

Supply only Brush Arm of existing size for 750 KVA Servo Voltage Stabilizer, complete all as specified and directed.

Supply only Slip ring of existing size for 750 KVA Servo Voltage Stabilizer, complete all as specified and directed.

Supply only PCB Card for 750 KVA Servo Voltage Stabilizer, complete all as specified and directed.

Material and labour for painting to steel tubular pole 8.5 to 11 metre long with two coats of synthetic enamel paint up to 1.50 metre height from ground level in 30 cm alternative black and yellow strips and remaining portion with two coats of aluminium paint on MS frames like channel,clamps, angle, D-clamps etc. including numbering of pole No. by stensils complete all as specified and directed.

Material and labour for two coat of synthetic enamel paint on LT panel / feeder pillar any size after preparation of surface by rubbing with emery paper to remove rust, dust etc. complete all as specified and directed.

M&L cable jointing kit for 11KV(Earthed) grade cable for outdoor termination heat shrink type joint complete with jointing material and accessories suitable for 3 core XLPE armoured aluminium conductor cable of size 50 sqmm to 95 sqmm and testing complete all as specified and as directed.

M&L cable jointing kit for 11KV(Earthed) grade cable for straight through heat shrink type joint complete with jointing material and accessories suitable for 3 core XLPE armoured aluminium conductor cable of size 50 sqmm to 95 sqmm and testing complete all as specified and as directed.

M&L for earthing complete with MS galvanized plate of size 60cmx60cmx6mm as earth electrode , buried directly in ground (earth pit not less than 2.25 mtrs deep below ground level) with top edge of the plate not less than 1.5 mtrs below normal ground level, connected to galvanised iron strip 32×6mm as earthing lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No 3 in SSR Part I of 2009 connected to earting test point all as specified complete with excavation & earth work, PCC pit with 50mm thick RCC cover having suitable handle (10mm MS Rod) 20mm dia GI medium grade watering pipe with GI funnel with wire mesh 40mm bore GI pipe medium grade ISI marked) for protection of earth lead conductor and testing on completion complete all as specified and directed.

M&L for Earthing complete with copper plate electrode 30cmx30cmx3.15 mm thick, buried directly in ground (earth pit not less than 2.25 mtrs deep below ground level) with top edge of the plate not less than 1.5 mtrs below normal ground level, connected to copper strip 20x3 mm as earthing lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No 3 in SSR Part I of 2009 connected to earthing test point all as specified or indicated complete with excavation & earth work, PCC pit with 50mm thick RCC cover having suitable handle (10mm MS Rod) 20mm dia GI medium grade watering pipe with GI funnel with wire mesh 40mm bore GI pipe medium grade ISI marked) for protection of earth lead conductor all as directed and testing on completion.

Repair/ maint LT feeder pillar box / DB, 415 Volt, by taking out burnt out portion, dressing, crimping, replacement of gland, lugs, terminal nuts and bolts, etc. complete all as required at site.

Excavating in Trenches not exc. 1.50 mtr wide and not exc. 1.50 mtr in depth, getting out as in Soft / Loose Soil, complete all as specified and directed.

Returning, Filling in, including Spreading, Levelling, Watering and Well Ramming in Layers not exc. 250mm as in soft / loose Soil, complete all as specified and directed.

Removing excavated materials (Soils) not exc. 50.00 mtr and depositing where directed at a level not exc. 1.50 mtr above the starting point, complete all as specified and directed.

Taking down /out unserviceable or serviceable UG cables of any cross sectional area and Connections including bricks, HDPE / GI Pipes, etc. of any descriptions, laid in Trenches and/or fixing with Walls/Poles including Segregating of Serviceable materials viz bricks, cables, GI pipes, etc. and keep in Safe custody for re-use, complete all as specified and as directed. NOTE : Earth work shall be measured and paid separately under relevant Items.

M&L for cable in trenches or passing through pipe, XLPE insulated, heavy duty, galvanised steel strip or wire armoured electric LT cable with stranded aluminium conductor for 1100 volts grade cross sectional area 10 sqmm 4 core complete all as specified and as directed.

M&L for cable in trenches or passing through pipe, XLPE insulated, heavy duty, galvanised steel strip or wire armoured electric LT cable with stranded aluminium conductor for 1100 volts grade cross sectional area 16 sqmm 4 core complete all as specified and as directed.

M&L for cable in trenches or passing through pipe, XLPE insulated, heavy duty, galvanised steel strip or wire armoured electric LT cable with stranded aluminium conductor for 1100 volts grade cross sectional area 50 sqmm 3.5 core complete all as specified and as directed.

M&L Sand cushioning (dry) in trenches for protec-tion of UG cables (below, above and around the UG cable laid in Trenches) of 230mm spread thick -ness and consolidated (punned) upto 180mm thickness, complete all as specified and as directed. NOTE : For the purpose of payment, punned thickness of sand cushioning shall only be measured.

S & F Sub-Class B brick, well burnt, laid breadth-wise along the length of cable laid in trenches oversand cushion laid for UG Cable protection, complete all as specified and directed.

Re-laying only old brick in trenches for under ground cable protection (Serviceable Materials obtained from Item No. 4 here-in-before), complete all as specified and directed.

S & F 50 mm high density polyethylene pipe (HDPE) of pressure rating 6 kgf/cm2 fixed to wall, ceiling or in floors etc. complete all as specified and directed .

Labour only for horizontal boring for passing protection pipe up to 80mm Bore (dia), under road / foot path, not exc. 10.00 mtr in a single length, complete all as specified and directed. Note: Pipe to be measured and paid separately under relevant item.

Supply and fixing MS Sheet Glow sign board of size 0.9M x 0.75M (thickness 2mm) and stand height not less that 1.2m from ground level and all accessories such as painting, PCC foundation including mentioning the name of installations, equipments, plants etc. complete all as specified and directed.

Repair of rectifier panels, 415 Vot by disconnecting incomuning and outgoing cables, taking out burnt out portion, dressing, crimping Painting, replacement of gland, lugs, terminal nuts and bolts sockets etc and reconnecting the cables complete all as required at site and as specified and directed. Note: Spare parts to be measured and paid separately under respective tems here-in-after

M&L for mild steel nuts, bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5 cm long and diameter of neck 5 to 10 mm, complete all as specified and directed

Supply and fix in repair 5 pin (3P+N+E) 380/415V, 32 Amp Panel mounting socket inclined outlet, with IP 66/57 protection complete all as specified and as directed. Make - Legrand Cat No. 5554 89 or equivalent in Havells/L&T

Supply and fix in repair 3 pin (2 P+ E) 200/250 V,16 Amp Panel mounting socket inclined outlet with IP 6567 protection complete all as specified and directed. Make: Legrand Cat No. 5553 84 or equivalent in Havells/L&T

S&F in repair MCB TPN 32 Amps ('C' curve) capacity, 10KA, 415 Volts including cable connection with copper lugs, complete all as specified and directed. Make : Legrand Cat Part No 408680 or equivalent in ABB/Havells/L&T

S&F in repair MCB SPN 6 - 32 Amps ('C' curve) capacity, 10KA, 240 Volts including cable connection with copper lugs, complete all as specified and directed. Make : Legrand Cat Part Nos 6 Amps-408587, or equivalent in Havells/L&T

Material and labour for PCC 1:2:4, type B-2 (by using 40 mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and directed.

Supply, fix grouting and painting HT/ LT cast iron cable route marker of 350 mm high, complete all as specified and directed. Note - The rate of excavation, PPC foundation for erection of cable route marker shall deemed to included in the quoted rate.

S&F 80mm dia galvanised iron pipe ‘light grade’ for protection of UG cable, laid in floors / road crossing, fixing to pole with mild steel clamps, nuts, bolts, etc., complete all as specified and directed.

Disconnecting/Taking down UNSV following Street / Perimeter / Garden / Security Roadway / Mast Light fittings from pole/Structure and repair / checking and identifying of foulty spares wirings, cleaning of fittings, cover, etc. and re assembling the same after repair, testing and refixing in original position and reconnecting with the electrical line complete all as specified and directed. Note - Spare parts shall be measured and paid separately under relevent items here in after.

Supply and fixing of following materials suitable for various type of light fittings dismantled from Serial item No. 83 here in before.

S&F electronic driver of 25Watt LED security light fittings. Make : Havells or equivalent model of C&S/Bajaj/CG

S&F electronic driver of 45 Watt LED security light fittings. Make : Havells or equivalent model of C&S/Bajaj/CG

S&F electronic driver of 75 Watt LED security light fittings. Make : Havells or equivalent model of C&S/Bajaj/CG

S&F 30 Watt LED light fitting, new generation energy saving & environmental friendly long life Versatile pressure die-cast aluminium aesthetically designed roadway luminaire with high power LEDs as light source & electronic driver, including cable for connection after taking down old unserviceable light fittings, complete all as specified and directed. Make:Crompton (Cat No- LSTS-30-CDL-M) or its equivalent model in Philips/GE as approved by GE

S&F 45 Watt LED light fitting, new generation energy saving & environmental friendly long life Versatile pressure die-cast aluminium aesthetically designed roadway luminaire with high power LEDs as light source & electronic driver, including cable for connection after taking down old unserviceable light fittings, complete all as specified and directed. Make:Crompton (Cat No- LSTS-45-CDL-M) or its equivalent model in Philips/GE as approved by GE

S&F 60 Watt LED light fitting, new generation energy saving & environmental friendly long life Versatile pressure die-cast aluminium aesthetically designed roadway luminaire with high power LEDs as light source & electronic driver, including cable for connection after taking down old unserviceable light fittings, complete all as directed. Make:Crompton (Cat No- LSTP-60-CDL-M) or its equivalent model in Philips/GE as approved by GE

S&F for 40W LED post top with moonlight effect and efficient light distribution and IP65 protection, including cable for connection after taking down old unserviceable light fittings, complete all as specified and directed. Make:Crompton (Cat No- LPTM-40-CDL) or its equivalent model in Philips/GE as approved by GE

S&F 72 Watt LED light fitting, new generation energy saving & environmental friendly long life Versatile pressure die-cast aluminium aesthetically designed roadway luminaire with high power LEDs as light source & electronic driver, including cable for connection after taking down old unserviceable light fittings, complete all as specified and directed. Make:- Crompton (Cat part No- LSTP-72-CDL-M) or equivelent model in Philips/ GE. As approved by GE.

S&F 90 Watt LED light fitting, new generation energy saving & environmental friendly long life Versatile pressure die-cast aluminium aesthetically designed roadway luminaire with high power LEDs as light source & electronic driver,including cable for connection after taking down old unserviceable light fittings, complete all as specified and directed. Make:Crompton (Cat No- LSTP-90-CDL-M) or equivalent model in Philips/GE as approved by GE

S&F for 120Watt LED flood light fitting, LED floodlight luminaire with high pressure die cast housing acting as heat sink in order to ensure better performance of the luminaires, complete including clamp,nut,bolt and other accessories for fixing,including cable for connection after taking down old unserviceable light fittings, complete all as specified and directed. Make-Crompton Cat No-LFLN-120-CDL/60-M or its equivalent model in Philips/GE as approved by GE

S&F for 150Watt LED flood light fitting, LED floodlight luminaire with high pressure die cast housing acting as heat sink in order to ensure better performance of the luminaires, complete including clamp,nut,bolt and other accessories for fixing ,including cable for connection after taking down old unserviceable light fittings, complete all as specified and directed. Make-Crompton Cat No-LFLN-150-CDL/60-M or its equivalent model in Philips/GE as approved by GE

S&F for 200Watt LED flood light fitting, LED floodlight luminaire with high pressure die cast housing acting as heat sink in order to ensure better performance of the luminaires, complete including clamp,nut,bolt and other accessories for fixing ,including cable for connection after taking down old unserviceable light fittings, complete all as specified and directed. Make-Crompton Cat No-LFLN-200-CDL/60-M or its equivalent model in Philips/GE as approved by GE

S&F for 250Watt LED flood light fitting, LED floodlight luminaire with high pressure die cast housing acting as heat sink in order to ensure better performance of the luminaires, complete including clamp,nut,bolt and other accessories for fixing ,including cable for connection after taking down old unserviceable light fittings, complete all as specified and directed. Make-Crompton Cat No-LFLN-250-CDL/60-M or its equivalent model in Philips/GE as approved by GE

S&F for 300Watt LED flood light fitting, LED floodlight luminaire with high pressure die cast housing acting as heat sink in order to ensure better performance of the luminaires, complete including clamp,nut,bolt and other accessories for fixing ,including cable for connection after taking down old unserviceable light fittings, complete all as specified and directed. Make-Crompton Cat No-LFLN-300-CDL/60-M or its equivalent model in Philips/GE as approved by GE

S&F 100Watt highbay light luminaire with high pressure die cast housing acting as heat sink in order to ensure better performance of the luminaires, after taking down old unserviceable light fitting, complete all as specified and directed. Make - Crompton, Cat No-LHB11-100-CDL/60-M or its equivalent make of Philips/ GE as approved by GE

S&F street light bracket on pole fabricated out of GI tubing light grade 40 mm bore, bend to the shape as directed and of length 1.0 mtr complete with mounting MS clamp of flat iron size 25X5 mm of suitable length 02 pairs including nut bolts etc of suitable size and painting to MS clamp with two coats of aluminium paints over a coat of aluminium primer complete all as specified and directed.

S&F Cable Junction Box 200X160X98mm in size, made out of thermoplastic, having IP 65 protection for outdoor installation fixed with 4 way bakelite cable terminals including 03 Nos polymide gland with check nut (M-32 -02 No & M-25 -01 No) fixed on poles with Aluminium clamps of size 25x3mm, nuts, bolts, washers etc. including taking out of old unserviceable cable junction box complete all as specified and as directed. Make : Cat No. K-9250 of HENSEL or its equivalent model of SPELSBERG/ RITTAL as approved by GE.

M&L in repair for PVC insulated three core 2.5 sqmm multistrand aluminium conductor for connection of security light from junction box to security light complete all as specified and directed.

Supply and passing through steel tubular pole or service connection in repair 1100 volts grade heavy duty cable PVC insulated stranded aluminium conductor, three core cable of size 4 sq mm complete all as specified and directed.

Supply and fix LED aviation light luminaries comprising of aluminium housing with polycarbonate encloser with 302 nos LED ,including cable for connection after taking down old unserviceable light fittings, complete all as directed Cat No:- BGAV302 LED of make Bajaj or its equivalent model of Philips/ CG as approved by GE Note:- The contract sum shall be calculated by deducting the amount shown in Credit Schedule attached to this tender, from total amount of Schedule 'A'/BOQ.

THE SUPPLY AGENCY

M/S DHAR AND DHAR

M/S SR CONSTRUCTIONS

M/S RK SAHA AND CO

M/S KRISHNA CONSTRUCTION CO

M/S PAUL CONSTRUCTION

Bidder Name

M/S RK SAHA AND CO

THE SUPPLY AGENCY

M/S DHAR AND DHAR

M/S SR CONSTRUCTIONS

M/S PAUL CONSTRUCTION

M/S PS ENTERPRISE

M/S KRISHNA CONSTRUCTION CO