SPECIAL REPAIR TO BLDG NO P-68 AND P-69 AT NAGARWALA ROAD OF SAW, ACC AND S IN THE AREA OF AGE B/R II UNDER GE(N) AHMEDNAGAR

Amount

Demolition of cement concrete (un-reinforced) in ground floor & paving n.exc. 15cm thick below or above ground level.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified.

M & L moorum filling in floors or paving laid in layers n.exc. 15 cm thick spread leveled and rammed including watering complete all as specified and directed

M & L hard core of gauge etc. 63 mm but n. exc. 100 mm deposited spread and leveled in layers n. exc. 15cm thick water and rammed etc. Complete all as specified and directed.

M/L for providing 75mm thick PCC 1:4:8 type D2 using 40mm graded stone aggregate as in sub base complete all as directed.

Material and labour for 60 mm thick, PCC pavers interlocking tiles of glossy finish, with grey cement and no pigment ,any shape & size conforming to IS 15658 of 2006. M-35 grade made up with 12.5mm graded mechanically crushed stone aggregates, factory made over and incl 30mm thick sand cushioning and joints filled with fine sand incl leveled with plate vibrator & sweeping etc complete all as specified and directed.

M&L for coloured glazed ceramic tiles digitally printed 300x450mm, 7-8 mm thick as approved by GE as in dado / skirting or on vertical surfaces, over and including 10 mm thick backing coat in CM (1:4) set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile etc complete all as specified and directed.

Material and labour for joint free / rectified anti skid ceramic coloured tiles 7-8mm thick matching to dado tiles area of each tile 400x400mm , as in floor etc laid over and including screed bed 15 mm thick in cement mortar 1:6 set and jointed with white or coloured cement to match complete all as specified and as directed.

M&L for joint free anti skid ceramic coloured tiles 300x300mm 7-8mm thick matching to dado tiles area of each tile, as in floor etc laid over and including screed bed 15 mm thick in cement mortar 1:6 set and jointed with white or coloured cement to match complete all as specified and as directed.

M&L for joint free / rectified anti skid ceramic coloured tiles 8-10 mm thick as approved by GE (square /rectangular) area of each tile 600x600mm, as in floor etc laid over and including screed bed 15 mm thick in cement and sand mortar (1:6 ) set and jointed with white or coloured cement to match the shade of tile etc complete all as specified and as directed

All as per item No 10 but as in dado/skirting on vertyical surfaces over and including 10 mm thick backing coat in CM (1:4) set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile etc complete all as specified and directed.

M&L in repairs for 20-25mm thick machine cut kota stone slab in flooring,steps over 20 mm thick screed base in cement and sand (1:6) mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing etc complete all as specified and directed by Engineer-in-Charge

M&L in repairs for Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar including 15 mm thick backing coat in cement and sand mortar (1:4) etc complete all as specified and directed by Engineer-in-Charge

M/L for 15 to 20mm machine cut kota stone slab of single piece jambs and double piece cills overall lenght of window riser of steps, skirting, dado and pillar laid over cement mortar backing coat jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing with beewax polish/ mirror polishing over and including rendering/ backing coat coat of 15 mm thick in CM 1:3 all as specified and directed. complete all as specified and as directed by EIC

M&L in repairs for 15mm to 18mm thick pre-polished granite stone slab of approved shade and color Jet Black / Telephone Black as in top table, top of WHB, kitchen slab/platform, steps, gate pillars, cills, jambs etc or on vertical surfaces including vertical projection, full round molding the edge including 10 mm thick backing coat in CM (1:3) jointing & pointing in white cement (1:2 ) using marble dust with admixture of pigment to match the shade of granite rubbing including dismantling etc complete all as specified and directed by Engineer-in-Charge

M&L in repairs for Machine cut cudappah stone slab 20-25mm thick over and including 15mm thick cement and sand screed in CM (1:6), laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing etc complete all as specified and directed by Engineer-in-Charge

M&L for 30-40mm thick rough dressed Shahabad stone as in floor/plinth etc over and incl 15mm thick screed bed in CM 1:6 complete all as specified and directed

Fixing only 30-40mm thick rough dressed Shahabad stone as in floor/plinth etc over and incl 15mm thick screed bed in CM 1:6 including dismantling complete all as specified and directed

Demolition of reinforced cement concrete of any descriptions and in any position etc complete all as specified and directed.

M&L for RCC Type B-1 1:2:4 using 20 mm graded aggregates as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete and floor slab.

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

Demolition of brickwork or stone bouilder masonary built in cement mortar or lime mortar complete all as specified

M&L for Walling of random rubble,uncoursed well bonded, bedded and solidly hearted built in CM 1:6 complete all as specified

M&L for brickwork with fly ash bricks straight or curved on plan exc 6m mean radius,built in CM 1: 6 complete all as specified

M&L for brickwork with fly ash bricks straight or curved on plan exc 6m mean radius,built in CM 1: 6 complete all as specified

Raking out cement mortar joints/ pointing to random rubble or polygonal rubble uncoursed or brought up to courses etc complete all as directed.

M&L for Pointing to random rubble or polygonal rubble uncoursed or brought up to courses in CM 1:4 etc complete all as directed.

Taking down cement mortar plaster on brick or stone walls, raking out joints, hacking for key complete all as directed

M&L for rendering, 20 mm thick (15mm+5mm) on brick/Stone Masonry/concrete surfaces in cement mortar 1:6 surfaces finished even and smooth without using extra cement including sagol finished complete all as specified.

M&L for rendering, 15 mm thick on stone/brick / concrete surfaces in cement mortar 1:4 finished even and fair without using extra cement complete all as specified and directed.

M&L for rendering, 15 mm thick on concrete surfaces of Chajjas top in cement mortar 1:4 finished even and fair using extra cement including scaffholding etc complete all as specified and directed.

M&L for rendering, 15 mm thick on concrete surfaces of Chajjas soffits and in cement mortar 1:4 neeru finished to plastering using extra cement including scaffholding etc complete all as specified and directed.

M&L for rendering 5mm thick on concrete surface of ceiling in CM 1:3 finished even and fair without using extra cement complete all as specified and directed.

M & L for preparation of newly plastered surface of wall and apply two coats of OBD over a coat of primer any height including scaffholding etc complete all as directed.

M&L for preparation of new plastered treated surfaces of walls by brooming down and and applying two coats of weather proof 100 % acrylic exterior emulsion apex ultima paint over a coat of any tint as approved by GE after cleaning the surfaces complete all as specified and as directed.

M&L for preparation of old untreated plastered surfaces of walls by brooming down and and applying two coats of weather proof 100 % acrylic exterior emulsion apex ultima paint over a coat of any tint as approved by GE after cleaning the surfaces complete all as specified and as directed.

M & L for preparation of newly plastered surface of ceiling and apply three coats of white wash any height including scaffholding etc complete all as directed.

M&L for preparation of old plastered or unplastered surfaces of ceiling including cornices etc by brooming down or steel wire brushing scraping down smook soot, moulds, moss and efflorescent salt, trading oil and greasy spots and applying one coat of white lime wash at any height including scaffholding etc complete all as specified and directed by Engineer-in-charge.

M & L for preparing old plastered surfaces of walls and apply two coat of OBD, finished with roller finish on plastered surfaces of wall any height including scaffholding etc complete all as specified and directed

M&L for 1 mm thick wall care putty etc complete all as specified and directed

S&F fix in repairs wash hand basin with pedestal vitreous China white , flat back or angle type of size 500 X 400 mm incl pillar tap 15mm dia CP, waste chain and plug and porcelain stopper , waste pipe, a pair of brackets, or erecting stand and PVC connection etc complete all as specified and directed by Engineer-in-Charge

S&F in repairs vitreous China white squatting pan, Orissa pattern of size 580 X 440 mm width with integral foot rest set in cement concrete including flush pipe and connecting to trap / flushing cistern etc complete all as specified and directed by Engineer-in-Charge.

S&F in repairs 10 ltr capacity PVC valve less, symphonic action type, flushing cistern, low level, all accessories etc complete all as specified and directed by Engineer-in-Charge.

S&F in repairs, chromium plated shower rose (Square type Size 200 X 200mm) with shower arm etc complete all as specified and directed by Engineer-in-Charge.

Taking up or down 15 mm bore steel tubing and connections

Ditto all as per item No 45 above but 20 mm bore tubing

Ditto all as per item No 45 above but 25 mm bore tubing

Supplying and laying 16 mm dia of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including all fittings complete all as specified.

Ditto all as per item No 48 above but 20 mm bore tubing

Ditto all as per item No 48 above but 25 mm bore tubing

S & F in repairs PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified.

S&F in repairs stop cock/ anglecock/ two waycock cast copper alloy, Chromium plated fancy type screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union and fix of size 15 mm bore etc complete all as specified and directed by Engineer-in-Charge

Supply and fixing in repairs tubular towel rail, brass chromium plated 20 mm dia `D' type, 60 cm long between flanges including a pair of brackets all as directed.

S&F in repairs bib tap, 15 mm dia, CP cast copper alloy with crutch or butterfly handle screwed down for iron pipe or for brass ferrule etc complete all as specified and directed by Engineer-in-Charge.

S&F in repairs fancy type twin (Two way) bib tap, 15 mm dia, CP cast copper alloy with crutch or butterfly handle screwed down for iron pipe or for brass ferrule etc complete all as specified and directed by Engineer-in-Charge.

S&F in repairs 15 mm dia pillar tap, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with long screwed shanks and fly-nuts, screwed for iron pipe all as directed.

S & F in repairs PVC flexible 32 mm Waste pipe for WHB, Sink etc complete all as specified.

S&F in Repairs Sink coupling PTMT(half or full threated), with rubber washer etc complete all as specified. Minimum weight 32mm-45Gms/40mm-60Gms

S&F in repair PVC (SWR) 110mm bore (dia) soil, waste and vent Pipe, (ISI Marked), in any length with rubber ring Joints fixed to wall with necessary stay clamps/ laid in trenches/floor etc complete all as specifed and directed.

All as per item No. 59 above but As in trenches or floor

S&F in repair PVC (SWR) 75mm bore (dia) soil, waste and vent Pipe, (ISI Marked), in any length with rubber ring Joints fixed to wall with necessary stay clamps/ laid in trenches/floor etc complete all as specifed and directed.

All as per item No. 61 above but As in trenches or floor

S&F PVC (SWR) 110 mm bore (dia), Bends any type, etc. and Jointing with Solvent Cement, complete all as specified and as directed

S&F PVC (SWR) 75mm bore (dia), Bends any type, etc. and Jointing with Solvent Cement, complete all as specified and as directed

S&F PVC (SWR) junction single, (Single T) equal or un equal 110mm bore

S&F PVC (SWR) junction single, (Single T) equal or un equal 75mm bore

S&F PVC (SWR) junction single, (double Y) equal or un equal 110mm bore

S&F PVC (SWR) vent cowl110mm bore

M&L for special treatment to sunken slab floor incl WC trap etc including cleaning and preparing the surface area for carrying out membrane water proofing treatment, then injection grouting the weak areas on the concrete surface with cementitious grout and applying 10mm thick cement plaster in CM 1:4. Then providing and laying Mineral Top APP (Atactic Polypropylene Polymer) modified prefabricated 5 layer 4mm thick water proofing membrane, black finished reinforce with non woven polyester matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 Litre per Sqm by the same membrane manufacturer of density at 25ºC, 0.87-0.89 Kg per litre and viscosity 70-160 cps. Over the primer coat the layer of membrane shall be laid using Butane Torch and sealing all joints etc and preparing the surface complete. and providing PCC 1:5:10 type E2 using 40mm graded mechanically crushed stone aggregates in sunken slab and 75mm thick PCC 1:4:8 type D2 using 40mm graded mechanically crushed stone aggregates as base, 40mm bore GI pipe, light grade of length not less that 50 cm as spout, non-skid glazed tiles as per existing pattern/size/tint with and incl WC vitreous china squatting pan 580x440mm with integral footrests/pedestal pan incl seat cover, white, area of WC n exc 1.50 Sqm etc after dismantling the existing sunken floor etc complete all as specified and directed by Engineer-in-Charge Note : Work has to be carried out strictly by the authenticated applicator of the manufacturer and as per manufacturers specification as approved by GE.

S&F rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) of 1000 litres capacity, triple layered, hoisted and fixed in position including 20 mm dia ball valve, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed to iron pipe, tank nipple and connected complete all as directed.

M&L for cleaning of service tank up to 1000 ltrs by removing all scales, dirt, silt, mud etc from tank and mouth of outgoing pipe including washing of tank internally with bleaching powder after removing scale, dirt, silt, mud etc from tank and removing algae from outside of tank from below bottom of tank and disinfecting tank by spraying sodium hypo chloride solution in tank and writing date of cleaning on tank with synthetic enamel paint size of alphabet / numerical shall be minimum 7 cm etc complete all as specified and directed by Engineer-in-Charge. Note:- The quoted rate shall include dismantling and refixing of water tank as etc complete all as specified and directed by Engineer-in-Charge

S&F in repair 20mm dia ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball and high density plastic ball screwed to iron pipe, tank nipple and connected (Minimum weight 15mm-142Gms/20mm-210Gms) complete all as directed.

Cutting chases in brick/ block wall, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth

Taking down chowkhats or frames not exc. 1.5 Sqm each with shutters (without taking off shutters from the frames) etc complete all as specified and directed by Engineer-in-Charge

Taking down chowkhats or frames exc. 1.5 sq. m and n exc 4.00 Sqm each with shutters (without taking off shutters from the frames) etc complete all as specified and directed by Engineer-in-Charge

Taking down shutters of any description exc 1 Sqm but n exc 2 Sqm each etc complete all as specified and directed by Engineer-in-Charge

Taking down shutters of any description n exc 1 Sqm each etc complete all as specified and directed by Engineer-in-Charge

S & F Pressed steel door frame of size 125 x 60mm for doors with one or more rebates including necessary fixing lugs, hings, lock strike plate, etc, complete all as specified,

S & F pressed steel door frame of size 105 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc, complete all as specified,

S&F 35 mm thick IInd C/L H/W glazed & skeleton shutters open rebated and prepared to receive glass gauge, divided into square or rectangles with plain chamfered or rounded mitered & rebated slash bars including beads mitered for securing glass wire gauge etc all as specified

M&L for 35 mm thick plain framed, paneled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial plywood. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated

S&F 30 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides

M&L for 0.9 mm thick decorative laminate type 1 on Flush door surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructions

S&F Solid PVC Door frame size 50mm x 47 mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, supplying & fixing in opening as per specification & drawing

S&F factory made solid PVC moulded Door shutter with particle board core, 28 to 30mm thick (stiles) with 2,4 or 6 raised panel design with 2mm thick moulded PVC sheet on the front face & 2mm plain colour PVC sheet on back space, supplying and fixing in frame at site as per specification & drawing.

M&L 18/19mm thick Veneered decorative plywood, grade 1(with BWR resin) with decorative face veneers on one face; fixed with screws to timber frame work

S&F powder coated aluminium anodised aluminium frame, shutters for door,windows, ventilators with one or more rebates including joining cleat for fixing etc, rubber / neoprene beading and locking arrangement etc complete all as specified and directed by Engr-in-Charge

S&F anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified

S & F aluminium anodised grill ( with minimum 15 Micron anodizing) conforming to DG- 102 of Deco Grill or equivalent , (10mm X 5.2mm) thick of approved design or equivalent as approved by Accepting Officer and fixing with and including 'F/U' channel not less than 1.5mm thick complete all as specified and directed.

S&f Steel ventilator with top hung shutter including hinges, steel peg stay, complete

S&F butt hinges medium weight cold rolled mils steel 100mm long.

Supply and fixed mild steel butt hinges of 50mm length, cold rolled, medium weight, complete all as specified.

S&F aluminium anodised barrel tower bolts of extruded section 150mm long.

S&F aluminium anodised handle of extruded section 150mm long.

S&F aluminium alloy, anodised, sliding door bolt with hasp, staple and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy 300mm long.

S&F 300 mm mild steel ordinary rat tail rod pattern door spring including roller and roller plate complete all as specified and directed.

S & F in repair Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40 mm and fixed in any position any type of opening with and including wooden beads complete all as directed by Engr-in-Charge.

S & F Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40 mm and fixed in any position any type of opening with and including wooden beads complete all as directed by Engr-in-Charge.

S&F, 150mm long hasp & staple, safety type, alu anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws completed as specified and directed.

S&F continuous (Piano) hinges mild steel, bright finish or electrogalvanised, width of flap 30mm completed as specified and directed.

S&F 150mm long floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring.

Hacking out old broken glass ( any thickness size ,quality or description ) from wooden/Steel frames glazed with putty or fixed with beads.

M & L for 3 mm thick sheet frosted/pin headed glass ordinary quality and glazing with oil putty or wooden beads in squares n.exc 0.50 sqm in each pane.

M & L for 4 mm thick plain sheet frosted/pin headed glass ordinary quality and glazing with oil putty or wooden beads, rubber bedding in squares n.exc 0.50 sqm in each pane.

M & L for preparation of new wooden surface and applying two coats of synthetic enamel paint over a coat of pink primer complete all as directed.

M & L for preparation of old wooden surface and applying one coat of synthetic enamel paint.

M & L for preparation of new steel surface and applying two coats of synthetic enamel paint over a coat of red oxide.

M & L for preparation of old steel surface and applying one coat of synthetic enamel paint.

M&L Providing cement concrete Type C1 1:3:6 20mm graded aggregate) in kerbs or mud stops, rounded or chamfered on edges

Supply only polymer based lilquid water proofing compound.

S&F in repairs sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plug, washers and waste including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915 x 420 mm bowl size 410 x 330 x 160mm including waste coupling, waste pipe etc complete all as specified and directed by Engineer-in-Charge.

S&F in repairs stainless steel kitchen plate rack made out of 0.63 mm thick stainless steel sheet of size 36''x 36''x 10'' with complete accessories including screws etc complete all as specified and directed by Engineer-in-Charge. Make Nirali or equivalent

S & F in repairs decorative looking mirror of size 500 mm x 700 mm without border fixed with round shape screw etc complete all as specified and directed by Engineer-in-Charge.

S&F curtain rod 25mm dia, having corrugated PVC extrusion on eletric resistance welded MS pipe with fancy type 02 nos Knobs and 02 Nos brackets per each door/ windows etc complete all as specified and directed

S&F in repair wall mounted cloth drying stand consisting of 16 mm dia powder coated MS rods of CR steel mounted on powder coated MS square pipe, 16- 4 rods, 4ft each, total weight not less than 3.80 Kg, fixed to wall including all fittings/accessories etc complete all as specified and directed by Engineer-in-charge Make -Easy dry Model: Mount it or Equivalent product in Nirali/Prayag.

Full moulding/half moulding of stone slabs one edge, two edge, as in steps cooking platforms jambs and cills and other similar situations complete all as specified & directed.

S&F pegs set of 116 Nos, power coated a/u body fixed with cadmium plated screws as directed.

S&F PVC (SWR) Nahani /Floor trap, 75 mm dia of out let, plain with grating including jointing to waste pipe with solvent cement.

S&F Chromium plated soap dish of Prayag polymers Pvt Ltd or equivalent

Dismantling of fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section

M&L for Framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors ladders framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165

Dismantling of framed timber scantling 40 Sq, Cm and over in section, in any position

Dismantling of asbestos cement, corrugated or semi corrugated sheets in roofing

M&L for pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering fixed with self tapping screws including dismantling corrugated steel sheeting, any gauge, thickness complete all as directed

S&F of Steel work in tubular trusses, Perlin, rafhter, including special shaped washer etc. complete conforming to I. S.1161-1979 grade St.-240

S&F of steel work in post, Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. as per Fe 410 -W (Gde- E- 250) quality- A

S&F,structural rolled mild steel Fe 410-00 (Gde E-250) Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment

S&F18/19mm thick colour PVC Prelaminated board fixed to timber frame work as in cup board shutter/Shelves palmet box and similar items fixed in repair complete all as specified and directed.

S&F Auto closing hinges 35mm of 0 crank (KH-001) or B crank (KH-002) openable at 110 degree for kitchen cabinet shutters fixed in repair complete all as specified and directed

S&F ball bearing runners 45mm telescopic (KTS-20) full etension load capacity 50Kgs fixed in repair complete all as specified and directed

S&F stainless steel handle 100mm size for kitchen cabinet shutters fixed in repair complete all as specified and directed

S&F Chromium plated stainless steel wire basket (storage basket) pull out type for large utensils size 480X500X300mm of grade 304 with necessary fixing clips etc fixed in repair complete all as specified and directed

S&F Chromium plated stainless steel wire basket (storage basket) pull out type for large utensils size 480X500X150mm of grade 304 with necessary fixing clips etc fixed in repair complete all as specified and directed

S&F Chromium plated stainless steel wire basket ( plate basket) pull out type for large utensils size 380X500X150mm of grade 304 with necessary fixing clips etc fixed in repair complete all as specified and directed

S&F Chromium plated stainless steel wire basket ( cup and soucer basket) pull out type for large utensils size 380X500X100mm of grade 304 with necessary fixing clips etc fixed in repair complete all as specified and directed

S&F Chromium plated stainless steel wire basket ( Cutlery basket) pull out type for large utensils size 380X500X100mm of grade 304 with necessary fixing clips etc fixed in repair complete all as specified and directed

M&L for 2nd class hardwood exc 13 & n exc 25 Sq cm plain fillets square, rectangular or triangular in section, clean sawn, secured with nails or brands

M&L for RCC Type B-1 1:2:4 using 20 mm graded aggregates as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete and floor slab.

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

M&L for toohing bonding with old RCC stucture with new RCC Sructure including racking out plater inserting and welding New TMT Bar etc complete all as specified and directed by Engr-In-Charge

S&F in repair fancy type brass CP wall mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and as directed by engineer-in-charge.

S&F (in repair) stainless steel plate rack of standard size, weight not less than 5kg, complete all as specified.

Ms. M.D. Auty

Avinash B Kullal

M/S. YADAV ENTERPRISES

MATOSHREE CONSTRUCTION

M/s Meher Construction

MS. G.A. CONSTRUCTION

M/s. N D Karande