PROVN OF 05 X TOILETS WITH 05 X BATHROOMS AT UNITS LINES, 313 COY ASC AND SPECIAL REPAIR TO BLDG NO T-3, T-4, T-8, P-04 AND P-17 OF HQ 51 SUB AREA UNDER GE NARANGI

Amount

Surface excavation n.exc 30 cm deep and averaging 15cm deep in soft/loose soil and getting out complete all as specified and directed.

Excavation over area, n. exc 1.5m in depth and getting out in soft/ loose soil complete all as specified and directed.

Excavation in trenches n.exc 1.50 m wide and n.exc 1.50 m deep for foundation or for shafts, wells cesspits,man holes etc n exc 10sqm on plan and n exc 1.5m in depth and getting out in soft/loose soil complete all as specified and directed.

Returning, filling, in soil including spreading, levelling, watering and well ramming in layers n.exc. 25cm thick complete all as specified and directed.

Removing excavated soil to distance n. exc. 50m and depositing where directed at a level n. exc. 1.5 m above the starting point etc complete all as specified and directed.

Dismantling of plain or corrugated steel sheeting, any gauge or any thickness in roof covering complete all as specified and directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws as specified complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed

S&F 1mm thick Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 complete all as specified and as directed

Demolition of plain cement concrete (un-reinforced) in ground floors and paving not exceeding 15cm thick above or below ground level complete all as specified and directed.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

M&L for hardcore of broken stone or boulders of gauge n. exc. 63 mm, deposited, spread and levelled in layers n. exc. 15 cm thick, watered and rammed to a true surface etc. complete all as specified and directed.

M&L for PCC 1:4:8, type D2 (using 40mm graded stone aggregate) as in foundation, filling and mass concrete etc. complete all as specified and directed.

M&L for 75mm thick PCC 1:4:8, type D2 (using 40mm graded stone aggregate) as in sub base, floor etc. complete all as specified and directed.

M&L for 75mm thick PCC 1:3:6, type C2 (using 40mm graded stone aggregate) as in plinth protection, etc finished the surface even and smooth without using extra cement including provision of joint of size 10 mm wide and 30 mm deep at every 2.4mtrs interval filled with bitumastic compound etc complete all as specified and as direted.

M&L for 40mm thick PCC 1:2:4, type B1 (using 20mm graded stone aggregate) as in floor, finished the surface even and smooth using extra cement complete all as specified and directed.

M&L for 25 mm thick PCC 1:2:4, type B0 (using 12.50mm graded stone aggregate) as in floors complete all as specified and directed.

M&L for PCC 1:2:4, type B1 (using 20 mm graded stone aggregate) as in coping, cills, hold fasts, fixing of post, water trough etc. including for use of necessary formwork (straight or curved) complete all as specified and as directed.

M&L for 100mm thick PCC 1:2:4, type B2 (using 40mm graded stone aggregate) as in path/paving/hard standing/floor and finished the surface even and smooth without using extra cement complete all as specified and directed.

M&L for RCC 1:1.5:3, type A-1 (using 20mm graded stone aggregate) as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc. complete all as specified and directed.

M&L for RCC, A1 1:1.5:3 (using 20mm graded stone aggregate) as in beams, seismic bands, cantilevers, bressumers and lintels over 1.5m span complete all as specified and directed.

M&L for RCC 1:1.5:3, type A-1 (using 20mm graded stone aggregate) as in columns, pillar, piers, posts and struts etc. complete all as specified and directed.

M&L for RCC type 1:1.5:3, type A-1 (using 20mm graded stone aggregate) as in Slabs supported on walls,sunshade, chajja, floors, roofs, landings, balconies, canopies, deck slabs etc. complete all as specified and directed.

M&L for TMT bars 10 mm dia and over cut to length, bent to shape as required including cranking, bending spirally for hooping for columns,hooking ends and binding with mild steel wire(annealed) not less than 0.9mm dia as in reinforcement bar complete all as specified and directed.

All as per item No 24 here in above but 5mm dia and over upto and including10mm dia as in stirrups, spacers and binders complete all as specified and directed.

Taking down roof trusses, coupling rafters of clear span above 4m & upto 8m but including taking down trusses etc., for renewal of any defective members (timber renewed to be measured separately) and reassembling etc complete all as directed.

S & F mild steel framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work of water tanks and similar work conforming to Fe 290, Gde-E-165 complete all as specified and directed.

M & L for steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S. 1161-1998 grade St.-240 complete all as specified and directed.

M & L for mild steel roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc confirming to grade Fe-410-W (Gde E 250) for fixing complete all as specified and directed.

M & L for framed work as in doors or gates of angle or other section with gusset plates, rails, braces,hold fast etc, complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive or steel sheeting or other covering, running rails and guides) and hanging; also fastening complete all as specified and directed.

M & L for mild steel section conforming to Fe 290 grade E-165 as in wind ties, fixed at eaves and ridge level etc complete all as specified and directed.

Use and waste formwork to sides of concrete foundations, footing, bases of columns, plinth beams for rough finished surfaces of concrete complete all as specified and directed.

Use and waste formwork to sides and soffits of floor or roof beams, beams haunchings, girders, bressumers, lintels, cantilevers, shelves including supports overhangs etc also splays between floors and beams etc. in rough finished flat surfaces of concrete complete all as specified and directed.

Use and waste formwork to sides of pillars, posts, struts, piers, columns and stanchions for fair finished surfaces of concrete complete all as specified and directed.

Demolition of brick or stone masonry work, built in cement mortar as in wall including all quoins, arches, pillars etc complete all as directed.

M&L for brick work with sub class ‘B’ bricks (locally available best quality) straight or curved on plan exceeding 6m mean radius, built in cement mortar (1:6) complete all as specified and directed.

All as per item No 36 but except brick. Note : Old serviceable brick obtained against item No 35 here in above shall be re used

Taking down cement plaster on walls, chajja surfaces, etc including raking out joints, hacking for key, scrubbing down with water complete all as specified and directed.

M&L for 15 mm thick rendering in cement mortar 1:6 on brick/ concrete surfaces and finishing the surfaces even and smooth without using extra cement etc complete all as specified and directed.

M&L for 15mm thick rendering in cement mortar (1:4), in two layers, under coat of 10 mm thick & top of 5 mm thick, to fair faces of brick or concrete wall surfaces, top layer 5 mm thick mixed with water proofing compound (@ 3% by weight of cement or as per manufacture's instructions), finished even and smooth without using extra cement complete all as specifed and directed by Engineer-in-Charge. Note : Water proofing compound to be measured and paid separately as "Supply only

M&L for rendering 5mm thick in cement mortar 1:3 on fair faces of RCC concrete surfaces and including applying cement slurry in bottom of slab, chajjas, fin, facias etc. complete all as specified and directed.

Supply only integral water proofing compound

Dismantling floor, hearth or wall tiling including cement mortar bedding but not backing complete all as specified and directed.

M&L for coloured Non-skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.36 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed or bedding layers in cement mortar (1:6) complete all as specified and as directed.

All as per item No 44 here in before but as in vertical surfaces like dado or skirting, set & joined in neat cement slurry and pointed in white cement mixed with colour pigment to match the colour of tiles, laid over and including 10 mm thick rendering in cement mortar (1:4) complete all as specified and directed.

M&L for coloured Non-skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, laid over and including 15 mm thick screed bed or bedding layers in CM (1:6) complete all as specified and as directed.

All as per item No 46 here in before but as in vertical surfaces like dado or skirting set & joined in neat cement slurry and pointed in white cement mixed with colour pigment to match the colour of tiles, laid over and including 10 mm thick rendering in cement mortar (1:4) complete all as specified and directed.

M&L for coloured glazed ceramic tile 300mmx200mmx7mm/ 350mmx250mmx7mm / 450mm x350mmx7 mm thick as in vertical surfaces like dado or skirting set & joined in neat cement slurry and pointed in white cement mixed with colour pigment to match colour of tiles,laid over and including 10 mm thick rendering in cement mortar (1:4) complete all as specified and directed.

M&L for machine cut kota stone slab flooring 20-25mm thick over cement screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing over and including 20 mm thick screed in cement mortar (1:4) complete all as specified and directed.

M&L for machine cut kota stone 20-25mm thick as in vertical surface like riser of steps, skirting, dado and pillar joined in neat cement slurry and pointed in white cement mixed with colour pigment to match colour of kota stone, laid over and including 10 mm thick rendering in cement mortar (1:4) complete all as specified and directed.

M&L for Granite work 20mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like with and including 15mm bedding in cement mortar 1:6 and pointing in white cement (1:2) using marble dust with admixture of pigment to match the colour of tiles etc complete all as specified and directed.

M&L for pre polished chequered cement concrete tiles, area exc .06 Sqm but not exc 0.11 Sqm, 25 mm thick with white cement and pigments of approved make, jointed with cement slurry and pointed with white cement mixed with colour pigment to match with the colour of tiles laid over and including screed bed of 20 mm thick cement mortar (1:4) for laying floor finishes complete all as specified and directed.

Taking down chowkats with shutters including builders hardware(without taking off shutters from the frame) n.exc. 1.5 Sqm each complete all as specified and directed.

Taking down chowkats or frames exceeding 1.5 Sqm but not exceeding 4 Sqm each including shutter with builders hardware (without taking off shutters from the frame) complete all as specified and as directed.

Taking down shutter of any description exc 1 sqm but n exc 2 Sqm each including builders hardware complete all as directed.

M & L for 2nd class hard wood, plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered put together with glue pinned at joints complete all as specified and directed.

M&L for 1.25mm thick mild steel pressed steel frames of size 105x60mm for doors with single rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directed.

S & F 30 mm thick flush shutter, solid core construction with particle board core and plywood face panel, commercial type on both side complete all as specified and directed.

S & F 35 mm thick second class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc (with out sash bar), edges of framing with plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, sizes of members of shutters all as specified in SSR part-I section 8 clause 8.24 (a) complete all as specified and directed.

S&F 30mm thick second class hard wood, glazed and skeleton shutters, open rebated divided into square and prepared to receive glass, gauze etc (with sash bar of any number), edges of framing with plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, sizes of members of shutters all as specified in SSR part-I section 8 clause 8.24 (b) complete all as specified and directed.

M & L for 19 mm thick one side prelaminated particle board and other side balancing white lamination interior grade and fixed with screws to timber frame work in cup - board shutters complete all as specified and as directed.

S & F PVC door frame of size 50 mm x 47 mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed.

S&F Factory made solid PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the M.S frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying and fixing in the frame at site as per specfication, drawing and complete all as specified and as directed.

S & F mild steel butt hinges 100mm size, cold rolled, medium weight complete all as specified and as directed.

S&F mild steel butt hinges 75mm size, cold rolled, medium weight complete all as specified and as directed.

S&F 100mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

S & F 150 mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

S&F 100 mm extruded aluminum alloy handles, fabricated type, anodized complete all as specified and directed.

S&F 150mm size extruded aluminium handles fabricated type, anodised and polished etc. complete all as specified and directed.

S&F 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed.

S&F 40mm flap width Continous (piano) hings mild steel bright finish or elecrogalvanised complete all as specified and directed.

S & F Ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed complete all as specified and directed.

S&F anodized aluminium sliding glazed window shutter (double leaf glazed shutter and single leaf mosquito proof shutter each in single frame work) without sash bars with anodized aluminium shutter of section 40.00mmx20.00mmx1.10mm thick and window chowkat of section 92.00mmx29.50mmx1.20mm thick including necessary jointing cleats, glazing clips, rubber packing, snap beading, screws, handle, tower bolts and locking arrangement etc. and 4mm thick sheet glass, tinted quality on panel and aluminium anodized wire cloth for mosquito proofing, 0.45mm nominal dia and average width of aperture 1.40mm fixed with aluminium screws and tacks and making good to disturbed surfaces complete all as specified and as directed.

S&F steel window or ventilator with side hung shutters both mosquito proof and glazed shutter including projecting type hinges with steel handle and steel peg stay with glazing bars and 12 mm square bar or round bar of approved design welded to steel window frame dovetailed or welded complete all as specified and directed.

S&F stain less steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or aluminum wire staples complete all as specified and directed.

S&F 3mm thick Sheet glass, ordinary quality and glazing with oil putty in squares not exceeding 0.5 Sqm in each pane complete all as specified and directed..

S&F 20 mm thick, 2nd class hard wood boarding, clean sawn, planed one side with butt joints and fixed with nails in any situation as in eaves board, etc. complete as specified and directed.

S&F mild steel chromium plated curtain rod 20 mm dia with fixing brackets, stops, roller etc complete all as specified and as directed.

Dismantling unframed timber scantling 40Sqcm and over in section in any position complete all as directed.

Dismantling unframed timber scantling under 40Sqcm in section in any position complete all as directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards/slabs of any thickness including cover fillets complete all as directed.

M&L for suspended false ceiling using E-grid 2430, 180 GSM (exposed ceiling suspension system ) of grid size 600mmx600 mm with main runner 38 mm x 24 mm and wall angle 24mm x 24mm using 4mm thick High Pressure stean Crude Everest Non Asbestos Fiber Cement plain Board (E-Board Classic) in a grid of GI system duly suspended with 4mm dia GI wire hanger fixed with steel dash fasteners or iron purlin from the roof with adjustment clip providing positions for light fixtures,air conditioning diffuser and ducts ,sprinkler ,smoke detectors etc.The main runners to be secured to structural soffits by hanger @ 1220 mm maximum c/c. the last hanger at the end of each main runner should not be placed at more than 450mm from the adjucent wall,Flush fitting 1220 mm cross tee to be interlocked between main runners @ 610mm c/c,so as to form 600mm x 600 mm grid complete all as specified and directed.

M&Lfor preparation of new or previously untreated surfaces of wood and wood based surfaces of any description, not otherwise described exceeding 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M & L for preparation of old wooden surface over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M & L for preparation of new and previously un-treated steel surfaces of any description, not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M & L for preparation of old painted steel surfaces of any description, not otherwise described over 10 cm width or girth and applying one coats of synthetic enamel paint complete all as specified and directed.

M & L for preparation of new and previously un-treated steel surfaces of any description, not otherwise described n exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall and applying two coats of oil bound distemper over a coat of alkali resistant primer complete all as specified and directed.

M&L for complete removal of existing treatment of wall and applying two coat of oil bound distemper over one coat of alkali resistant primer complete all as specified and directed .

M&L for preparation of newly plastered or unplastered surface of walls and applying three coat of white wash complete all as specified and as directed.

M&L for preparation of newly plastered surface of walls and applying two coat of cement base paint over one coat of primer complete all as specified and as directed.

M&L for complete removal of existing treatment of wall, preparation of surfaces and applying two coat of cement base paint over one coat of primer complete all as specified and as directed.

S&F GI tubing 15mm bore, medium grade with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

S&F in repair GI tubing 15mm bore, medium grade with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

S&F GI tubing 20mm bore, medium grade with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

S&F in repair GI tubing 20mm bore, medium grade with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

S&F Bib taps 15mm dia cast copper alloy chromium plated, fancy type with crutch or butterfly handles screwed down for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repair Bib taps 15mm dia cast copper alloy chromium plated, fancy type with crutch or butterfly handles screwed down for iron pipe or for brass ferrule complete all as specified and directed.

S&F stop valves/angular stop valve, 15mm dia, cast copper alloy, fancy type, chromium plated, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or unions complete all as specified and directed.

S&F in repair stop valves/angular stop valve, 15mm dia cast copper alloy, fancy type chromium plated, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or unions complete all as specified and directed.

S&F concealed stop cock with sheet flange cast copper alloy, screwed down high pressure, with round operating knob for 15 mm bore pipe or for unions complete all as specified and as directed.

S&F in repair concealed stop cock with sheet flange cast copper alloy, screwed down high pressure, with round operating knob for 15 mm bore pipe or for unions complete all as specified and as directed.

S&F 20mm bore dia stop valves, cast copper alloy, screwed down, high presure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and as directed

S & F 125 mm dia, chromium plated, swivel type shower rose with 190 mm long chromium plated shower arm and wall flange suitable for fixing 15 mm bore iron pipe complete all as specified and as directed.

S & F in repair 125 mm, dia chromium plated, swivel type shower rose with 190 mm long chromium plated shower arm and wall flange suitable for fixing 15 mm bore iron pipe complete all as specified and as directed.

S&F tubular towel Rail of 20mm dia and 60cm in length, D shaped, with brass chromium plated brackets complete all as specified and directed.

S&F in repair tubular towel Rail of 20mm dia and 60cm in length, D shaped, with brass chromium plated brackets complete all as specified and directed.

S & F sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with CP bracket guard and railing 60 cm long complete all as specified and as directed.

S & F in repair sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with CP bracket guard and railing 60 cm long complete all as specified and as directed.

S & F vitreous china soap dish, white, of size 160 mm x 160 mm x 90 mm complete all as specified and as directed.

S&F Vitreous China Squatting Pan"Orissa pattern" size 580 mmx440 mm white with integral foot rest etc. ( excluding cistern and flush pipe) including S or P Trap and provision of concrete bedding and making good to floor complete all as specified and as directed

S&F Vitreous china urinal, half stall white (excluding flushing cistern) including urinal spreader, PVC connection, 40mm PVC waste pipe & 40mm waste coupling providing and fixing plugs, bedding urinal against wall in mortar 1:2, securing urinal to plug, with and including 60mm long screws, pointing around urinal back in cement, fixing flush pipe, grating and union for discharge pipe complete all as specified.

S & F 10 Litres capacity PVC valveless syphonic action type, flushing cistern, low level, white or coloured, with inlet, ball valve, float and handle including brackets etc complete all as specified and directed.

S & F in repairs 10 Litres capacity PVC valveless syphonic action type, flushing cistern, low level, white or coloured, with inlet, ball valve, float and handle including brackets etc complete all as specified and directed.

S&F vitreous china wash hand basin, white flat back size 550 mm x 400 mm including brackets including pillar tap 15 mm bore chromium plated cast copper alloy with capstan heads, 32 mm waste coupling brass chromium plated suitable for wash hand basins, with long screwed shanks and fly nuts and PVC waste pipe,PVC connection pipe complete all as specified and as directed

S&F in repairs vitreous china wash hand basin, white flat back size 550 mm x 400 mm including brackets including pillar tap 15 mm bore chromium plated cast copper alloy with capstan heads, 32 mm waste coupling brass chromium plated suitable for wash hand basins, with long screwed shanks and fly nuts and PVC waste pipe,PVC connection pipe complete all as specified and as directed

M&L for 100mm dia cast iron floor trap/Nahani trap with grating, including grating jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified and directed.

S&F rotational moulded polyethylene water storage tank 2000 litre capacity of triple layered ISI mark, wall construction (Cylindrical, vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I including 20 mm bore dia ball brass valve high presure with polythene float and flynut complete screwed for iron pipe or brass ferrule and fixed etc complete all as specified and as directed.

S&F in repairs, rotational moulded polyethylene water storage tank 1000 litre capacity of triple layered ISI mark, wall construction (Cylindrical, vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I including 20 mm bore dia ball brass valve high presure with polythene float and flynut complete screwed for iron pipe or brass ferrule and fixed etc complete all as specified and as directed.

S&F 110mm dia PVC (SWR) pipes, pressure rate having 6 Kgf single socketed in any length with rubber ring joints and laid in trenches as in waste/soil pipe complete all as specified and as directed.

S&F in repair 110mm dia PVC (SWR) pipes, pressure rate having 6 Kgf single socketed in any length with rubber ring joints and laid in trenches as in waste/soil pipe complete all as specified and as directed.

S&F 110mm dia PVC (SWR) bends of any radius complete all as specified and as directed.

Taking down carefully any type of point wiring (light, fan, bell,socket or power), complete excluding fittings but including switches, ceiling roses, pendants, regulators, sockets, light fittings etc. and making good disturbed surfaces of walls, ceiling, floors etc to match with existing surface complete all as specified and directed.

M & L for wiring complete with 1.5 sqmm single core FRLS grade PVC insulated unsheathed,1100V grade copper multistranded in PVC concealed conduit & PVC insulated FRLS grade copper earth continuity conductor cable 1.5 sqmm connected to common earth dolly including steel terminal boxes made out of 1.2 mm thick MS sheet concealed in walls for housing the switches ,socket outlets ,fan regulators for one light/one fan point controlled by one switch complete all as specified and directed.

All as per item No 126 here-in-before but for One 3 pin 5 Amp switch socket outlet on independent board complete all as specified and directed.

All as per item No 126 here-in-before but for One 3 pin 5 Amp switch socket outlet on same board with other switches complete all as specified and directed..

All as per item No 126 here-in-before but wiring with 2.5sqmm size single core multistranded copper conductor cable for 6 pin 15 Amps switch socket combination outlet on independent board with 1.5 sqmm PVC insulated and unsheathed copper conductor as earth and connected to earth dolly complete all as specified and directed.

S&F switch piano, flush type single pole one way 5 Amps 230 volt complete all as specified and directed.

S&F socket outlet 3 pin, 2-in-1, 5 Amps flush type complete all as specified and directed.

S&F switch socket combination outlet 5 pin, 2-in-1, 5 Amp flush type complete all as specified and directed.

S&F switch socket combination multipurpose, 2 in 1, 6 pin, 5 & 15 Amp flush type complete all as specified and directed.

S&F lamp holder, insulated,PVC/ polycarbonate /bakelite body complete all as specified and directed.

ceiling rose surface bakelite 65x50mm three terminal complete all as specified and directed.

S&F stepped type electronic fan regulator, two module size, flush type complete all as specified and directed.

S & F LED light fitting 10 watt 230 volt including 10 watt LED tube, extruded aluminium for efficient heat dissipation with polycarbonate diffuser & integrated electronic driver complete all as specified and directed. Model LGLZ01X010XW, Make Jaguar or equivalent model of make Philips /Bajaj/Crompton.

S&F LED box type fitting pre-wired including LED tube 1x20W connecting up with PVC insulated and sheathed 1100 volt grade flexible copper cable complete all as directed. Make:- Jaguar Model-LGLZ01X020XC/ LGLZ01X020XN/LGLZ01X020XW. or equivalent model of make Philips /Bajaj/Crompton.

S&F Environmental friendly, ultra modern, energy saving, surface mounted, decorative oval bulk head t LED luminaire comprising of high brightness LEDs complete all as specified and directed. Model LBLK01X010XC, Make Jaguar

S&F in repairs 15 watt LED recessed mounted luminaire with high brightness LED for glare-free homogenous illumination suitable for Armstrong/grid ceiling and fixture size in mm (LxWxH) 295x295x70 complete all as specified and directed. Make : Havells Model- PLUTO1x1PLR15WLED840S/PLUTO1x1PLR15WLED857S or equivalent model in make of Philips/ Crompton/Bajaj

S&Fsingle pole & neutral, DBs, 8 Ways, double door, protection class IP-43, suitable for mounting MCB, DBs conforming to IS-13032, IS-8623, BS-5484 with minimum 200 Amp rating copper bus bar 240V and grouted in wall with PCC, 1:2:4, type B1, using 20mm graded stone aggregate complete all as dierected. Make :- Legrand Cat No 6077 11 or equivalent model of make Siemens/Schnider

S&F in repair single pole & neutral, DBs, 8 Ways, double door, protection class IP-43, suitable for mounting MCB, DBs conforming to IS-13032, IS-8623, BS-5484 with minimum 200 Amp rating copper bus bar 240V and grouted in wall with PCC, 1:2:4, type B1, using 20mm graded stone aggregate complete all as dierected. Make :- Legrand Cat No 6077 11 or equivalent model of make Siemens/Schnider

S&F MCBs, SPN 6 to 32 Amps, 10 KA , IS/IEC 60898-1 2002 marked fixing in DBs complete all as specified and directed. Make :- Legrand Cat No 4086 18 4086 20 or equivalent model of make Siemens/Schnider.

S&F MCBs, SPN 40 to 63 Amps, 10 KA, 'C' curve IS/IEC 60898-1 2002 marked fixing in DBs complete all as specified and directed. Make :- Legrand Cat No 4086 18 to 4086 20 or equivalent model of make Siemens/Schnider

S&F MCBs, SP 6 to 32 Amps, 10 KA, IS/IEC 60898-1 2002 marked fixing in DBs complete all as specified and directed. Make :- Legrand Cat No 4085 87 to 4085 95 or equivalent model of make Siemens/Schnider.

S&F RCBOs,four pole 63 Amp, 30mA complete all as specified and directed.

S&F for ventilating Exhaust fan 300mm sweep,230 volts metal frame with blades and louvres fixing on existing place complete with nut bolts complete all as specified and directed.Make- Havells or equivalent USHA/Bajaj /Crompton.

SS&F in repair heavy duty exhaust fans AC single phase 230/ 240 V of size 300 mm sweep,900 rpm with necessary fixing accessories , writing MES No. with black synthetic enamel paint 2 cm high in letter complete with necessary connection up including provision of three core copper flexible cable with flexible wire cover of plastic white in colour and connection from ceiling rose to exhaust fan terminal etc complete all as specified and directed.Make-Usha,Model-S.PH TURBO HDEF /Bajaj /Crompton.

M&L LED Street lighting luminaries 70 Watts WSPD epoxy powder coated pressure die cast aluminum housing with wheatherproof gasket for LED's and control gear compartments, pressure die cast aluminium frame with heat resistant toughened clear glass fixed with SS screws LED Specification: CREE LED/Equivalent, Colour temp - 6500 K +/- 300 K Lens,,IP-66,Lumen efficiany >100 lm/w,surge protection 4kv internal (Built-in) with twin core conductor complete all as directed including testing on completion complete all as specified and directed. Make: Havells CAT No. ENDURAPEARLPLUS70WLED757SASYTOPC or equivalent of Philips/Wipro/CG.Note-Driver of LED street light should be same as make approved.

M&L for Earthing complete with GI earth plate electrode of size 60cm x 60cm x 6.3mm buried directly in ground vertically at a depth not less than 2.25 metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level sorrounded from all sides by 15cm thick and packed layer of charcoal dust and common salt filling in alternate layers etc and connected to and including 4mm dia GI wire upto 7.5 m by means of bolts, nuts, check nuts and washers made of galvanised iron and protected by light grade 15mm dia GI pipe connected to main control board and GI pipe medium grade 20mm bore for watering and including funnel, wire mesh, charcoal,salt etc RCC pit cover flush to earth pit 50mm thick reinforced with 8mm TMT bar 100mmC/C and PCC chamber pit with PCC (1:3:6) type C1 (using 20mm graded aggregate) including excavation and earthwork disposal of surplus soil to distance not exceeding 50 metre) and testing after completion all as specified and shown on plate No 3 of SSR Part-I 2009 complete all as specified and as directed.

Supply, laying and testing cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10Sqmm 3 core complete all as specified and directed.

PK ENGINEERING

M/S ROY AND CO.

M/S KAMAKHYA CONSTRUCTION AND BUILDERS

M/S GOSWAMI COSTRUCTION

MOINUL HOQUE CHOUDHURY