SPL REPAIR OF BLDG No P15,P6,P27,T6 at HQ 73 MTN BDE AND SPL REPAIR TO ROOF OF BOYS, GIRLS TOILET AND WATER POINT AT APS DINJAN AND SPL REPAIR TO BLDG NO T20,T21 AND SPL REPAIR, REPLACEMENT OF INTERNAL ELECTRIFICATION AT 671 ARMY AVN UNDER GE DINJAN

Amount

Demolition of plain cement concrete (unreinforced) in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) complete all as specified and as directed.

Dismantling timber scantlings 40 Sqcm and over in section, in any position, unframed work complete all as specified and as directed.

Dismantling timber works in fillets, rail, post, rafter, purlins etc under 40 Sq.cm in section (unframed work), in any position complete all as specified and as directed.

S&F for second class hard wood plain fillets, square, rectangular or triangular in section, clean sawn, secured with nails, cross sectional area exceeding 3 Sqcm and not exceeding 6 Sqcm complete all as specified and as directed.

S&F for second class hard wood plain fillets, square, rectangular or triangular in section, clean sawn, secured with nails, cross sectional area exceeding 6 Sqcm and not exceeding 13 Sqcm complete all as specified and as directed.

M&L for second class hard wood plain fillets, square or rectangular in section, exceeding 3.00Sqcm and not exceeding 6.00Sqcm in cross sectional area, bullnosed, splayed, chamfered or rounded on one edge or face fixed with screws complete all as specified and as directed.

M&L for second class hardwood, scantlings, wrought, timber framed and fixed complete all as specified and as directed.

Taking down the chowkhats or frames not exceeding 1.5 Sqm each (without taking off shutters from the frames) complete all as specified and as directed

Taking down the chowkhats or frames exceeding 1.5 Sqm but not exceeding 4 Sqm each (without taking off shutters from the frames) complete all as specified and as directed

Taking down the shutters of any description not exceeding 1.00 Sqm each complete all as specified and as directed

M&L for aluminium anodised, window and ventilator shutters, fixed type, with or without sash bar, using aluminium section weighing not less than 0.55Kg per metre including necessary joining cleats, glazing clips, rubber neoprene packing, aluminium handles 2 numbers in each shutter, hinges, anodised aluminium snap beading, screws etc complete all as specified and as directed. Note : a) Thickness of aluminuim section shall not be less than 1.5mm. b) Glass will be measured and paid separately

M&L for anodised aluminium section, medium anodic coating of grade AC 15 for frame of doors, windows, ventilators with one or more rebates including joining cleats for fixing etc complete all as specified and as directed.

M&L for 75 mm thick plain cement concrete (1:3:6), type C1, (using 40mm graded stone aggregate) as in plinth protection, finishing surface even and smooth without using extra cement making joint with bitumastic filling in proportion of bitumen and sand (1:2), complete all as specified and as directed

S&F 35 mm thick, second class hard wood, glazed and skeleton shutters with open rebated and prepared to receive glass, gauze, etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut mitered beads for securing glass, etc, sizes of members of shutters as specified in SSR Part I, Section -8, clause 8.24 (a).

S&F 30 mm thick, second class hardwood glazed and skeleton shutters open rebated and prepared to receive glass, gauge, etc, divided in to squares, with plain, chamfered or rounded, mitered and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded as in SSR Part I Section 8 clause 8.24 (b) complete all as specified and as directed..

S&F 35 mm thick, second class hardwood, plain, framed, panelled shutters (any number of panels), with lock rail and panels of 9mm BWR commercial Ply or 12mm thick veneered particle board medium density, with commercial face veneering on both faces. the size of rail and styles 150 & 100mm, kiln seasoned and chemically pressure treated complete all as specified and as directed.

S&F 35 mm thick, second class hardwood, plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers, supplied and fitted to chowkats complete all as specified and as directed.

S&F for solid PVC door frames of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified and as directed.

S&F for factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded, plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour 5mm thick PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, complete all as specified and as directed by Engr-in-Charge.

S&F for 100mm size butt hinges, medium weight, cold rolled mild steel complete all as specified and as directed.

S&F 75 mm size stainless steel, butt hinges, medium weight, cold rolled, complete all as specified and as directed.

S&F 150 mm long, aluminium handles, cast type, anodised complete all as specified and as directed.

S&F 100 mm long, aluminium handles, cast type, anodised complete all as specified and as directed.

S&F 150mm long aluminium, anodised, barrel tower bolts of extruded section complete all as specified and as directed.

S&F 100mm long aluminium, anodised, barrel tower bolts of extruded section complete all as specified and as directed.

S&F for 300 mm long, aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections etc complete all as specified and as directed.

Dismantling of wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed.

M&L forJoist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) complete all as specified and directed.

M&L for Mild steel framed work such as grills, gratings, gates etc., with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bar, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe-410-0 Gde E-250 complete all as specified and directed.

S&F for mild steel small articles using flat iron of size 25x3mm thick such as band, strap, hold fast, cleat, support, hook, hinges, base tie for door frame etc and other similar items conforming to Fe-290 (Gde E-165) complete all as specified and as directed.

M&L for plain cement concrete (1:2:4) type B-1 (using 20mm graded stone aggregate) for embedding hold fast, bed block, cills, etc including necessary form work complete all as specified and as directed.

S&F in repair galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.00mm and fixed with wooden bit or stainless steel wire staples as required complete all as specified and as directed.

S&F for galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.00mm and fixed with wooden bit or stainless steel wire staples as required complete all as specified and as directed.

S&F for 4 mm thick tinted glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

S&F in repair steel windows with side hung shutters including projecting /box type hinges with steel handle, and steel peg stay complete with glazing bars, devotailed or welded complete all as specified and as directed.

Dismantling asbestos cement (corrugated or semi corrugated) sheet in roof covering complete all as specified and as directed.

S&F for pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of profile as approved, any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F for pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridges/valley gutter, fixed with self tapping screws complete all as specified and as directed. Note : Colour of ridge shall be same colour as that of sheet used for roof.

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and as directed.

M&L for anodised aluminium snap grid size 605 X 605 mm frame work for false ceiling complete all as specified and as directed.

S&F for hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and as directed.

M&L for 4 mm thick non asbestos fibre cement building boards fixed or laid/ inserted to timber/GI/Aluminium framework with screws including three coats of white wash on surface of ceiling/boards etc complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

M&L for non-skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed bed or bedding layer of cement mortar in (1:6) for laying floor finishes complete all as specified and as directed.

M&L for non-skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed bed or bedding layer of cement mortar in (1:6) for laying floor finishes complete all as specified and as directed.

M&L for glazed ceramic, coloured tiles of size 450X 350X 7 mm thick , on vertical surfaces such as skirting, dados etc, including 10 mm thick bedding in cement mortar (1:4) and set & jointed in neat cement slurry & pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and as directed.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar (1:6) and finished surfaces even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar (1:4) mixed with integral water proofing compound weight of cement as per manufacturer's instructions and finished surface even and smooth without using extra cement complete all as specified and as directed. Note : WPC shall be measured and paid separately against relevant item.

M&L for rendering 10 mm thick of internal wall on fair faces of brick work or concrete surfaces in cement mortar in (1:6) and finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 5 mm thick on ceiling in cement mortar (1:3) finished even & smooth without using extra cement complete all as specified and directed

Supply only liquid water proofing compound complete all as specified and as directed.

Demolition of reed, lathing, single or double including battens and plaster or chicken wire lathing complete all as specified and as directed.

M&L for GI wire netting 0.90mm dia and 12mm mesh lathing to wood or metal studding, joists, etc. in walls, ceilings, stanchions, beams, etc. including all laps, cutting and waste fixed with tinned tacks of wire staples complete all as specified and as directed.

M&L for rendering 18 mm thick (12+6) externally one side of lathing in cement mortar 1:6 and finished the surfaces even and smooth without using extra cement, mixed with integral water proofing compound @ 2% by weight of cement on top layer surface complete all as specified and directed. (Note : WPC shall be measured and paid separately against respective item).

M&L for rendering 12 mm thick on one side of lathing in cement mortar 1:6 and finished the surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for preparation of old wooden surfaces of any description, exceeding 10 cm width or girth and applying one coat of synthetic enamel paint complete as specified and as directed.

M&L for preparation of new wooden surface of any description, not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

M&L for preparation of new wooden surfaces of any description, not exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

M&L for preparation of new steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of zinc chrome red oxide primer complete all as specified and as directed.

M&L for preparation of old painted steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

M&L for preparing old plastered or unplastered surfaces of walls by washing, rubbing down and stopping nails holes, filling cracs with putty etc and applying two coats of distemper oil emulsion complete all as specified and as directed.

M&L for preparing old plastered surfaces of walls, etc and applying two coat of cement base paint complete all as specified and as directed.

M&L for preparation of new plastered surface of walls etc and applying two coats of cement base paint over a coat of alkali resistant priming paint complete all as specified and as directed.

M&L for preparation of new plastered surface of walls etc and applying two coats of distempering interior walls with distemper oil emulsion white or tinted over chalk whiting complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of walls and applying two coat of oil bound distemper over a coat of primer over 3mm thick wall care putty complete all as specified and as directed.

M&L for preparation of new plastered surface of walls etc and applying three coats of white wash complete all as specified and as directed.

M&L for preparation of new plastered surface of ceiling etc and applying three coats of white wash complete all as specified and as directed.

M&L for preparation old decorated plastered or unplastered surfaces of wall cornices etc by brooming down or steel wire brushing, scraping down, the surfaces covered by smoke soot, growth of moulds and moss, efflorescent salts, trading oil and grease spots and applying one coat of white wash complete all as specified and as directed.

M&L for preparation old decorated plastered or unplastered surfaces of wall cornices etc by brooming down or steel wire brushing, scraping down, the surfaces covered by smoke soot, growth of moulds and moos, efflorescent, having oil and gresase spots and applying one coat of cement base paint (white or tinted) including scaffolding if required complete all as specified and as directed

Taking up or down 15 mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed.

Taking up or down 20 mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed.

Supply and laying, CPVC pipe of 16mm outer dia, SDR 11 pain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and as directed.

Supply and laying, CPVC pipe of 20mm outer dia, SDR 11 & plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and as directed.

S&F in repairs 15 mm bore, bib taps, cast copper alloy, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed.

S&F in repairs 15 mm bore dia cast copper alloy fancy type, chromium plated stop valves, crewed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed.

S&F in repairs 15 mm bore, pillar taps, fancy type, cast copper alloy, chromium plated with capstan heads, screwed down high pressure with or without lettered 'Hot or Cold' with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and as directed.

S&F in repair 15mm bore, PVC connection pipe 600mm long with PTMT nuts at both ends complete all as specified and as directed.

S&F in repair 1000 litres capacity rotational moulded polyethylene water storage tanks (cylindrical or vertical with closed top) as per IS 12701:1996, hoisted and fixed in position including provision of 20/15mm bore medium grade pipe for connecting inlet, outlet, overflow and washout pipe including 20 mm bore, ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed. (minimum weight 20 mm - 210 gms ) complete all as specified and as directed.

S&F in repairs 20mm bore, gun metal gate valves with iron wheel head screwed both ends for iron pipes or for unions complete all as specified and as directed.

S&F in repairs, PVC low level flushing cistern, 10 litre capacity, valveless, symphonic action type with inlet, ball valve, float and handle incl bracket, PVC conection pipe and flush pipe of polyethylene of low or high density or PVC 32 mm dia, complete all as specified and directed

S&F in repair vitreous china wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) making good to disturbed surfaces of floor by filling with PCC (1:4:8) type D-2 to match with the existings complete all as specified and as directed.

S&F in repairs vitreous China squatting pan, 'Orissa' pattern, size 580 x 440 mm white with integral foot rest and 'P' or 'S' trap, including provision of lime concrete bedding, connection to trap and flushing pipe etc complete including making good to disturbed surfaces of floor using concrete (1:2:4) type B0 and to match with existing specifications complete all as specified and as directed. Make : Cat No. C0117 of Parryware/Hindware/Cera.

S&F in repair 75mm dia, PVC (SWR) floor trap, plain with grating including jointing with solvent cement to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and as directed.

S&F for grating doom, circular type, 100mm dia of PTMT, (mimimum weigh 25 gms) complete all as specified and as directed.

S&F in repairs vitreous china wash basin, size 550x400mm, white, flat back, with PVC waste pipe, CP waste coupling, chain, plug and porcelain stopper & brackets including cutting for and pinning in ends of brackets but excluding tap complete all as specified and as directed. Make : Cat No. C0406 of Parryware/Hindware/Cera.

S&F in repair CP health faucet cast copper alloy with push button & 1m long flexible steel pipe with PVC lining suitable for 15mm bore pipe complete all as specified and directed.

S&F in repairs for vitreous china bowl urinal, flat back size of 465x355x265mm whitw with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) but fixing plug bedding urinal against wall in cement mortar (1:2) securing urinal to plug including 60mm long brass screws pointing around urinal back in cement mortar including 15mm brass stop cock and waste coupling brass CP complete all as specified and as directed.

S&F in repairs 40mm dia waste coupling of PTMT (half or full threaded) (Minimum weight 32mm-45gms/ 40mm-60 gms) complete all as specified and as directed.

S&F in repair PVC waste pipe of 32 mm size flexible (coil shape) and 1.2 mtr long, fitted to basin or sink complete all as specified and as directed.

Dismantling of cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required complete all as specified and as directed.

S&F in repairs 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and as directed.

S&F in repairs 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

S&F in repairs 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and as directed.

S&F for 110 mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and as directed.

S&F for 110 mm bore PVC (SWR) bends any radius complete all as specified and as directed.

S&F for 110mm PVC (SWR), vent cowl complete all as specified and as directed.

Demolition of unreinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed

M&L for rendering 10 mm thick in cement mortar (1:3) with water proofing compound finished even and smooth (without using extra lime or cement in sunken floor) complete all as specified and directed. Note: Water Proofing Compound measured and paid separately.

M&L for applying two coats of water proofing coating by using super latex manufactured by pidilite industries ltd (or equivalent product by Appx 'A' ) , water and cement ratio as instructed by manufacturer's on sunken floor and wall complete all as specified and as directed.

M&L for plain cement concrete (1:3:6) type C-2, (using 40 mm graded stone aggregate) as in sunken floor complete all as specified and as directed.

Cleaning of open shaft of bldg including gully trap, cleaning with wire brush incl of grass, roots, bushes etc and taking out accumulated garbage etc, from shaft and removing the same to a distance not exceeding 50 meter, complete all as specified and as directed.

M&L for Cutting out cracks to V-section in existing roofs or terracing, cleaning out and filling solidly with a hot mixture of bitumen and clean dry sand 1:1 (by weight)

M&L for water proofing treatment on RCC roof etc. comprising with the following operation & as specified herein below:- (a) Taking down existing old tarfelt, bituminous compound including cleaning & removing debris to a distance exc 100 m n.exc.250m. (b) M&L 25 thick cement concrete type B0 1:2:4( 12.5 mm graded aggregate) finished even and smooth. (c) M&L for 15 mm thick cement mortar in 1:4 finished even and smooth. (d) Preparing & cleaning of fully dried cement plastered surface. (e) Applying one coat of cold bituminous primer to the plastered surface @ 0.25 litres per sqm conforming IS-3384. (f) A layer of APP based polymeric membrane membrane 3mm thick (minimum) weighing 3.5 kg per sqm reinforced with polyster non woven fabric (weighing not less than 160 gms/sqm) shall be applied over bituminous primer as specified above. Application of polymeric membrane shall be by torch application. The over lap shall be minimum 100 mm on transverse direction and 75 mm in longitudinal direction. (g) One coat of aluminium paint over APP membrane @0.11Kg/Sqm. Note:- Prior to execution of the APP Membrane works, leak proof test shall be done by ponding water on roof slab to minimum depth of 25 mm. The entire roof slab shall be flooded with water for 48 hours. The necessary barrier shall be made to make feasible to stagnate water for 48 hours on roof slab.

Taking down carefully aluminium/copper point wiring (light, fan, socket or power) including unserviceable light fittings, switch board complete, switch sockets, ceiling roses, pendants, regulators, sockets, etc and removing materials to store for keeping in safe custody or for taking credit and making good disturbed surfaces of walls, floors, etc complete all as specified and as directed.

M&L for point wiring with 1.5 Sqmm (nominal area), FRLSH PVC insulated, multistranded, single core unsheathed, copper conductor cables passing through and including PVC casing caping with all fittings and accessories of PVC casing caping (like Tee, bend etc.) complete fixed to walls /ceiling etc. with and including 1.5 Sqmm (nominal area) FRLSH PVC insulated, unsheathed, stranded, single core, copper cable green in colour as earth continuity wire connecting to common earth point including PVC terminal box (sunken type) with 3mm thick hylam sheet cover fixed with suitable sizes cadmium plated iron screws and washers etc. for mounting switches, sockets, fan regulators etc complete for one light/ fan /bell /buzzer point controlled by one, one way switches complete all as specified and as directed.

All as per item above but for one 3 pin 5 Amps, socket outlet, on Independent board.

All as per item above but for one 5 Amps, 3 pin socket outlet on the same board with other switches.

All as per item above but wiring with cables of size 2.5 sqmm & cables of size 2.5 sqmm as continuous earth wire for one 15/16 amp multi socket out let on independent board.

M&L for concealed point wiring with FRLSH, PVC insulated, unsheathed multistranded, copper conductor cables of 1.5 sqmm size alongwith one earth continuity conductor with FRLSH PVC insulated unsheathed multistranded copper conductor cable of 1.5 sqmm size passing through and including suitable PVC conduit with all fittings and accessories of PVC conduit (like Tee, bend etc.) complete fixed to walls /ceiling etc , including cutting chases, making good with cement mortar 1:3, terminated in and including providing PVC/modular metal box of suitable size with 3mm thick hylam sheet cover for fixing of switches, sockets, fan regulators etc for one light/fan/bell/buzzer point controlled by one, one way switches complete all as specified and as directed.

All as per item above but for one 3/5 pin, 5 Amps, switch socket combination, on Independent board.

All as per item above but for one 5 Amps, 3/5 pin, socket outlet on the same board with other switches.

All as per item above but wiring with cables of size 2.5 sqmm & cables of size 2.5 sqmm as continuous earth wire for one 15/16 Amps, switch socket combination, on independent board.

S&F for switch piano, flush type single pole, 230 volts, 5 Amp one way bearing ISI marked complete all as specified and as directed.

S&F for socket outlet, 2 in 1, 3 pin, 5 Amps, 240V bearing ISI marked complete all as specified and as directed.

S&F for switch socket combination, 2 in 1, 5 Amps, flush type, 240 volts bearing ISI marked complete all as specified and as directed.

S&F for switch socket combination, 5 in 1, 5/16 Amps, 240 volts, bearing ISI marked flush type complete all as specified and as directed.

S&F for bell push, flush type, 5 Amps 230 Volts, bearing ISI marked complete all as specified and as directed.

S&F for call bell, AC, 230 volts, single pole complete all as specified and as directed.

S&F for ceiling rose, 3 phase/ PVC/ polycarbonate, isolated body bearing ISI marked and including PVC box complete all as specified and as directed.

S&F for stepped type (five steps), electronic fan regulator, flush type (socket type) complete all as specified and as directed.

S&F for lamp holder PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and as directed.

S&F for LED bulb 9 Watt complete all as specified and as directed.

S&F in repair 9 Watt LED retrofit lamps complete all as specified and as directed.

S&F in repairs 18/20 Watt surface and wall mounting type LED batten with polycarbonate housing & integrated complete all as specified and as directed. Make : Havells, Cat No.LUMILINEBS18WLED865SPCWH or equivalent make of Appendix 'A'.

S&F in repairs 10 Watt LED, energy saving new generation bulkhead luminaire with opal diffuser including lamp connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and as directed. Make : Cat.Part No. LHEOAOP7UZ6W010 of Havells or equivalent make of Appendix 'A'.

S&F in repair 12 Watt Recess mounted pressure die-cast LED aluminium luminaire in powder coated white finish in round profile with optimized heat sink for efficient heat dissipation with separate replaceable electronic driver included cutting/opening of ceiling any type & fixing arrangement for light fitting complete all as specified and as directed. Make : Cat No.LHEJNP7CPZ1W012 of Havells or equivalent make of Appendix 'A'.

S&F in repairs 36 Watt LED, recess mounted deep drawn PLANO size (2 ft x 2 ft) CRCA housing with higher power, Seamless front frame with flat white hight transmission acrylic cover complete all as specified and as directed. Make : Cat. No.DROPDOWNFLAT2X2PLR36WLED830S of Havells or equivalent make of Appendix 'A'.

S&F in repairs LED street light fitting of capacity 45/50W, with pressure die cast housing , toughned glass and individual LEDs with secondary optics and IP 66 protection and impact resistance of IK07, including with necessary brackets /pipes/clamps & nuts& bolts for holding the street light fitting and twin core aluminum cable of 2.5 Sqmm as required in existing location complete all as specified and as directed. . Note: (Warranty on Driver, LEDs and PCB for 5 Years to be submitted by the contractor) (Necessary excavation, PCC work, Bracket, Connecting wire will be measured and paid separately under relavent items)

S&F in repairs street light bracket arm of length not less than 1.2 m made out of galvansied iron tubing 32mm bore, light grade to pole, etc with suitable size flat iron clamp, nuts, bolts including painting with two coats of aluminium paint over a coat of red oxide primer zinc chrome in MS clamp complete all as specified and as directed.

S&F in repairs 25 Watt LED building security light new generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high power LED as lighting source and lens embeded PC cover having TOP OPENING separate driver compartment with IP65 protection and impact resistance of IK07 including all fixing arrangement and taking down old light fittings of any type complete all as specified and as directed.

Taking down unserviceable sub-main wiring up to 10 sqmm with rigid steel conduits/PVC casing-caping including cutting chases for taking out conduits and making good disturbed surfaces complete all as specified and as directed.

M&L for sub main wiring with two run of 6 Sqmm (Nominal area) single core cable PVC insulated, multistranded, unsheathed, copper conductor cables (FRLSH), 1100 Volts grade drawn through PVC casing-caping/conduit of suitable size, fixed to wall/ceiling etc including one run of 6 Sqmm (nominal area) single core, PVC insulated, multistranded, unsheathed, copper conductor (FRLSH) as earth wire and duly connected to common earth point complete all as specified and as directed. Note : (a) PVC Casing-caping/conduit, two run wiring cables and one run of earth wire will be measured as one length (b) All incoming and outgoing cable shall be connected by using proper lugs & sockets.

M&L for sub main wiring with two run of 4 Sqmm (Nominal area) single core cable PVC insulated, multistranded, unsheathed, copper conductor cables (FRLSH), 1100 Volts grade drawn through PVC casing-caping/conduit of suitable size, fixed to wall/ceiling etc including one run of 4 Sqmm (nominal area) single core, PVC insulated, multistranded, unsheathed, copper conductor (FRLSH) as earth wire and duly connected to common earth point complete all as specified and as directed. Note : (a) PVC Casing-caping/conduit, two run wiring cables and one run of earth wire will be measured as one length. (b) All incoming and outgoing cable shall be connected by using proper lugs & sockets.

M&L for sub main wiring with two run of 10 Sqmm (Nominal area) single core cable, PVC insulated, multistranded, unsheathed, copper conductor cables (FRLSH), 1100 Volts grade drawn through PVC casing-caping/conduit of suitable size, fixed to wall/ceiling etc including one run of 6 Sqmm (nominal area) single core, PVC insulated, multistranded, unsheathed, copper conductor (FRLSH) as earth wire and duly connected to common earth point complete all as specified and as directed. Note : (a) PVC Casing-caping/conduit, two run wiring cables and one run of earth wire will be measured as one length (b) All incoming and outgoing cable shall be connected by using proper lugs & sockets.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m deep for foundation/laying of cable in trenches, not exceeding 10Sqm on plan and getting out in soft/loose soil complete all as specified and as directed.

Returning filling including spreading, levelling and well ramming in layers not exceeding 25cm thick in soil complete all as specified and as directed.

Removal of surplus soil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as directed.

M&L for common burnt clay building bricks, sub-class 'B' designation 75 of suitable size available in market to cover for LT underground cable, laid dry and flat abutting each other with gaps not exceeding 10mm including taking down old unserviceable bricks cable complete all as specified and as directed.

M&L for sand cushioning with dry clean sand 15cm below cable and 8cm above the cable complete all as specified and as directed. Note : Punned thickness shall be measured for payments.

Taking down undserviceable main switches , DBs, bus bar chamber incl all fittings and fixures such as MCBs, isolator, etc removing from site , complete all as specified and as directed.

S&F for factory made board distribution (DB) double door in sheet metal enclosure with common bus bar at incomming end, single pole & neutral, 8 way, 240 Volts, 200 Amps, suitable for housing MCBs including complete all as specified and as directed. Make : Cat. No. DHDPSHODRW08 of Havells or equivalent make of Appendix 'A'.

S&F for Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB of 20 Amps rating complete all as specified and as directed.

S&F for factory made board distribution (DB) double door in sheet metal enclosure with common bus bar at incomming end bus bar, triple pole & neutral (TPN), 4 way, 415 Volts suitable for fixing MCCBs in incomer and MCBs in outgoing complete all as specified and as directed.

S&F for MCCB, 415 V, AC, 36 KA breaking capacity, 4 pole of rating 160 Amps, with adjustable thermal & fixed magnetic setting, complete fixed with LT panel board all as specified and as directed.

S&F in repair MCB, double pole, 240 Volts, 6 to 32 Amps, 'C' Series, 10KA capacity complete all as specified and as directed.

S&F in repairs MCB, SPN, 240 Volts, 5 to 32 Amps, 'C' Series, 10KA capacity complete all as specified and as directed. Make : Cat No. 408609 to 408617 of Legrand or equivalent make in appendix 'A'

S&F in repair MCB, 'C' Series, SP, 240 Volts, 6 to 32 Amps, 'C' Series, 10KA capacity complete all as specified and as directed. Make : Cat. No. 408587 to 408595 of Legrand equivalent make of Appendix 'A'..

S&F in repairs PVC rectangular block for mounting, MCB DB's etc. with 3 mm thick plastic laminated sheet cover of size 350 mm x 300 mm and 50 mm deep complete all as specified and as directed

M&L for test point terminal box made of gun metal or phosphorous bronze, size 75x75x25 mm drilled and screwd including 3 Nos 8 mm dia 25 mm long hexagonal head screw including taking down old unserviceable complete all as specified and as directed.

M&L for earthing complete with GI earth plate electrode 600mm x 600mm x 6 mm thick burried directly in ground vertically to a depth not less than 2.25m below ground level with the top edge of earth plate at depth not less than 1.5m below ground level connected to galvanised earth lead wire 4.0 mm dia by means of bolts, nuts, check nuts and washers protected by 15mm bore light grade GI pipe, funnel with 20mm bore GI medium grade pipe for watering, wire mesh, including concrete pit in PCC (1:3:6) type C-1, pre-cast RCC 1:2:4 type B-1 cover slab of size 350x350x50mm reinforced with 8mm dia TMT steel bars @ 15cm centre to centre in both direction and 10mm dia MS handle of suitable size, charcoal or coke and salt in alternative layers, necessary earth work in soft/loose soil all as shown in Electrical Plate No 3 of MES Schedule Part I and testing the base in which pit cover rests made up of MS angle iron (Frame) complete as specified and as directed.

Supply, laying, jointing, testing and commissioning cross-linked polyethylene (XLPE) insulated, armoured, nominal cross sectional area of main conductor 10 Sqmm, 2 core, stranded aluminium conductor, ISI marked as per IS-7098 (Part-I) 1988 including cable glands, lugs etc to suit the cable size and to be laid in trenches, under floors, through GI pipe complete all as specified and as directed. Note : (1) Pipes shall be measured and paid separately under relevant items of this schedule. (2) Excvation and earth work shall be measured and paid seperately.

All as per item above here-in-before but cross sectional area of main conductor 16 Sqmm, 4 core.

All as per item above here-in-before but cross sectional area of main conductor 50 Sqmm, 3.5 core.

M&L for 32 mm bore, steel tubes, galvanised, light grade with all fittings, laid in floor/road crossing/drain etc as in UG cable protection complete to walls and ceilings or laid in floors including taking down old unserviceable pipe alongwith all fixing accessories complete all as specified and as directed.

M&L for 50 mm bore, steel tubes, galvanised, light grade with all fittings, laid in floor/road crossing/drain etc as in UG cable protection complete to walls and ceilings or laid in floors including taking down old unserviceable pipe alongwith all fixing accessories complete all as specified and as directed.

M&L for 40 mm bore, steel tubes, galvanised, medium grade with all fittings, laid in floor/road crossing/drain etc as in UG cable protection complete to walls and ceilings or laid in floors including taking down old unserviceable pipe alongwith all fixing accessories complete all as specified and as directed.

M&L for 25 mm bore, steel tubes, galvanised, medium grade with all fittings, laid in floor/road crossing/drain etc as in UG cable protection complete to walls and ceilings or laid in floors including taking down old unserviceable pipe alongwith all fixing accessories complete all as specified and as directed.

M&L for 25 mm bore, Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed including taking down old unserviceable complete all as specified and as directed.

Taking down carefully existing ceiling fan of any size/sweep/make from it's existing position, replacement of defective spare parts and re-assembling and refixing/hanging in the same position connecting with flexiable cable including testing complete as directed by the Engr-in-Charge. Note : GI pipe for hanging of ceiling fan measured under relevent item of this schedule.

R.D.CONSTRUCTION

Garg Brothers

Construction House

AFTAB ENTERPRISES

Bimal Trading Company

FREEZCON

J D construction