Repair of Sub Divisional Building at Electric JPDCL Office Building at Hiranagar under District Capex Budget 2021-22.

Amount

Labour to be engaged for clearance of site and removing of unhygenic mulba including disposal of the same before execution of work.

Engaging Carpenter for repair to minor carpenting works which are not susptiable

Dismantling doors, windows and clerestory windows of area of 3 sqm. and below(steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking incl. all leads and lifts

Taking out doors, windows and clerestory window shutters (steel or wood) of area 3 sqm. and below including stacking, all leads and lifts

Demolishing brick work in cement mortar manually/by mechanical means including stacking of serviceable material and disposal of unserviceable material ,all leads and lifts as per direction of Engineer-in-charge

Demolishing cement concrete manually/by mechanical means including disposal of material within 50 meters lead as per direction of Engineer-incharge: 1:3:6 or richer mix (i/c equivalent design mix)

Removing mortar from bricks and cleaning bricks including stacking all leads and lifts. (stacks of cleaned bricks shall be measured) from brick work in cement mortar

Demolishing R.C.C. work manually/by mechanical means incl. stacking of steel bars and disposal of unserviceable material within all lead and lift as per direction of Engineer-in-charge.

Regrading terracing of mud phaska covered with tiles or bricks, in cement by dismantling tiles or bricks, removing mud plaster, preparing the surface of mud phaska to proper slope, relaying mud plaster gobri leaping and tiles or bricks, grouted in cement mortar 1:3 (1 cement: 3 fine sand), including replacing unserviceable tiles or bricks with new ones and disposal of unserviceable material to the dumping ground (the cost of the new tiles or brick excluded) all leads and lifts

Applying a coat of residual petroleum bitumen of grade VG-10 of approved quality using 1.7 kg per square meter on damp proof courses after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

Providing and laying 400 micron thick transparent PVC sheet on roof under mud phaska cutting placing complete job.

Providing gola 75 x 75 mm in cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 10mm down gauge) incl. finishing with cement mortar 1:3 ( 1 cement : 3 fine sand) as per standard design in 75 x 75 mm deep chase incl. all leads, lifts & carriage of material by MT/ H.L.

Making Khurras 45 x 45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 ( 1 cement : 2 Coarse sand : 4 graded stone aggregate of 20 mm nominal size) over PVC sheet 1 m x 1m x 400 micron, finished with 12 mm cement plaster 1:3 ( 1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges, making and finishing the outlet complete incl. all leads, lifts & carriage of material by MT/ H.L.

Providing and fixing on wall face un-plasticized Rigid PVC rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion. (i) Single socketed pipes 110 mm diametre

Repairs to plaster of thickness 12mm to 20 mm in patches of area 2.5 sq. meters and under, including cutting the patch in proper shape raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground incl all leads and lifts With cement mortar 1:4 (1 cement : 4 coarse sand)

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete incl.all leads, lifts & carriage of material by MT / H.L.Size of tile 600x600 mm (Double Charged)

Earth work in excavation in trenches for foundations, drains, pipes, cables etc. (Not exceeding 1.5 mtr in width) and for shafts, wells, cesspits and the like not exceeding 10sqm on plan, depth upto 1.5mtr. incl. disposal of surplus excavated earth incl. all leads, lifts & carriage of material by MT / H.L.

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) incl. all leads, lifts & carriage of material by MT/ H.L.

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) incl. all leads, lifts & carriage of material by MT/ H.L.

Brick work with F.P.S. bricks of class designation 75 in foundation and plinth including all shapes, leads, lifts and carriage of material by MT / H.L. in cement mortar 1:6 ( 1 cement : 6 coarse sand)

Extra for brick work in superstructure above plinth level upto floor V level (By manual means) incl. all leads, lifts & carriage of material by M.T. H.L.

Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°,landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) incl. all leads, lifts & carriage of material by MT/ H.L.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete at all levels, Cold twisted bars incl. all leads, lifts & carriage of material by M.T. / H.L.

Centring and shuttering including strutting propping etc and removal of form work for

Foundations, footings, bases of columns etc. for mass concrete

Suspended floors, roofs, landings, balconies and access platforms.

Edges of slabs and breaks in floors and walls under 20 cms wide.

6 mm thick plaster to ceiling of mix 1 : 3 ( 1 cement : 3 fine sand) incl. all leads, lifts and carriage of material by M.T / H.L.

12 mm cement plaster of mix 1 : 6 ( 1 cement : 6 fine sand) including all leads, lifts and carriage of material by M.T / H.L.

15mm cement plaster on rough side of single or half brick wall of mix 1:6 (1 cement: 6 fine sand) incl. all leads, lifts & carriage of material by M.T / H.L.

Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturers) of 1st quality conforming to IS: 15622 of approved make in colour such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1: 4( 1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigment etc., complete.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement :3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 liter low level white P.V.C. flushing cistern, including flush pipe with manually controlleddevice (handle lever), conforming to IS:7231, with all fittings andfixtures complete, including cutting and making good the walls andfloors wherever required:18.2.1 W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing wash basin with C.I. brackets, 15mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required White Vitreous China Flat back wash basin size 450 x 300 mm with single 15 mm C.P. brass pillar tap

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality & colour: 450 mm long towel rail with total length of 495 mm,78 mm wide & effective height of 88 mm, weighing not less than 170 gms.

Renewing glass panes, with putty and nails wherever necessary including raking out old putty.Float glass panes of thickness 4.0 mm(weight not less than 10kg/sqm)

Providing and fixing fly proof wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions all complete.

With Galvanized M.S. Wire gauge with wire of dia 0.63 mm with 2nd class teak wood beading 62x19 mm

With Galvanized M.S. Wire gauge with wire of dia 0.63 mm with 12 mm mild steel U beading

Providing and fixing aluminum work for doors, windows,ventilators & partitions with extruded built up standard tubular sections/ appropriate Zsections & other sections of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber / neoprene gasket felt etc. Aluminum sections wherever required incl. cleat angle, Aluminum snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings & the directions of Engineer-in-Charge (glazing, panelling & dash fasteners to be paid for separately.)

For fixed portion powder coated aluminum (minimum thickness of powder coated 50 microns)

For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately.) Powder coated aluminum (minimum thickness of powder coated 50 microns)

Providing and fixing glazing in aluminum door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineerin-charge. (Cost of aluminum snap beading shall be paid in basic item.) With float glass panes of 5.0 mm thickness (weight not less than 12.50 kg / sqm)

Providing and fixing ACP sheet panelling 4.0 mm thick in Partition/doors of approved quality as per the direction of Engineer- in - Charge (Complete job)

Providing and fixing Anodized aluminum grill (Anodized transparent or dyed to required shade according to IS: 1868 minimum anodic coating of Grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing windows frame with C.P. brass/stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved Anodized aluminum standard section around the opening, all complete as epr requirement and direction of Engineer-in-charge. (only weight of grill to be measured for payment)

Providing and fixing aluminum sliding door bolts 300x16 mm ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete :

Providing and fixing aluminum tower bolts SI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete :

Providing and fixing aluminum handles125 mm ISI marked anodized (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade with necessary screws etc. complete.

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc.: Internal work-Exposed on wall 15 mm dia. nominal bore

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing .Rectangular shape 453x357 mm

Providing and fixing PTMT soap dish holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106gms.

Providing and fixing C.P. Jet of approved quality

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C waste fittings complete. Semi rigid pipe 32 mm dia

Providing and fixing 15 mm nominal bore C.P. brass bib cock of approved quality conforming to IS : 8931.

Providing and fixing 15 mm nominal bore C.P. stop cock (concealed) of standard design and of approved make conforming to IS : 8931

Providing and fixing 15 mm nominal bore C.P. brass angle valve for basin mixer and geyser points of approved make conforming to IS : 8931

Providing and fixing uplasticized PVC connection pipe with brass unions 45cm length 15 mm nominal bore

Providing and fixing PTMT grating of approved quality and colour.Circular type 100 mm nominal dia.

Providing and fixing G.I. pipes complete with G.I. fittings excluding trenching and refilling etc. (external work)

15 mm dia. nominal bore Medium

20 mm dia. nominal bore Medium

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (new work)

15 mm dia. nominal bore

20 mm dia. nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked, with cover & suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete

15 mm nominal bore

20 mm dia. nominal bore

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade, one or more coats on old work.

Finishing walls with water proofing cement paint of required shade on New work (two or more coats applied @ 3.84 kg/10sqm)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade, one or more coats on old work

YASHPAUL SINGH RATHOUR

M/S NARINDER PAUL SINGH CONTRACTOR

M/S KULJEET SINGH