PROVISION OF TILING AT TYPE-II (1 BLOCK-8 QTRS) AND TYPE-III (4 BLOCK-16 QTRS) AT YEDDUMAILARAM AND PROVISION OF STORE ROOM (20 X 20 FT) AT ARTY CENTRE UNDER AGE B/R-I OF GE GOLCONDA

Amount

Taking down cement plaster on wall of any description incl racking out joints for key, scrubbing with water etc. complete all as specified and directed.

M & L for rendering 15mm thick in cement mortor 1:4 on concrete or brick wall surfaces, finished even and fair, mixed with WPC @ at 3% by weight of cement (IWPC measured and paid separately) complete all as specified and directed.

Supply only integral water proofing compound.

M & L for rendering 10mm thick in cement mortor 1:6 on Brick wall surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M&L for two coats of oil bound distemper over a coat of alkali resistant primer on newly plastered surfaces of walls including 3mm thick wall care putty on wall and preperation of surface complete all as specified and directed.

M&L for preparing new plastered surfaces of walls and applying Two coats of cement based paint complete all as specified and directed.

M&L for rendering 5mm thick in CM (1:3) as in ceilings, concrete surfaces finished even and smooth (without using extra cement) and including preparation of new ceiling surfaces and applying three coat of white wash complete all as specified and directed.

M&L for Praparation of old plastered surfaces and applying One coat of White wash on Ceiling complete all as specified and directed.

M&L for complete removal of existing treatment and applying two oil bound distemper over a coat of alkali resistant primer on old surface of walls including 3mm thick wall care putty complete all as specified and directed.

M&L for complete removal of existing treatment and applying two coats of cement base paint on walls surfaces complete all as specified and directed.

Demolition of cement concrete on ground floor and paving n exc 15 cm thickness (below are above ground level) and removing debrish from site complete all as specified and directed.

M&L for 75mm thick Plain cement concrete (1:4:8) type D2 (40mm graded stone aggregate) as in sub base, rough finished surface all as specified and directed.

M&L for 25mm thick cement concrete (1:2:4) type B0 (using 12.5mm graded stone aggregate) as in sub-base and finished surface even and smooth without using extra cement, complete all as specified and directed.

M&L for Coloured printed Non Skid ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in floors over 15mm thick sement screed in CM 1:6 and set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed (colour & design approved by Engr -in-Charge).

M&L for Coloured printed Glazed ceramic tiles on vertical surfaces of size 300x450mmx7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the colour of tiles over 10mm plaster in CM 1:4 complete all as specified and as directed (colour & design approved by Engr -in-Charge).

Excavating over areas, n exc 1.5m deep and getting out in hard/dense soil complete all as specified and as directed

Excavating in trenches n.exc 1.5m wide and n.exc 1.5m in depth for oundation, etc or for shafts, wells cesspits manholes, pier holes, etc n exc 10 sqm on plan and n.exc 1.5m in depth and getting out in hard/dense soil complete all as specified and as directed

M & L for PCC type D2 1:4:8 (40mm graded Aggr) in foundations, filling and mass Concrete complete all as specified and as directed

Returnng, filling in including spreading, levelling, watering and well ramming in layers not exc 25cm complete all as specified and as directed

Removing excavated material n exc 50m and depositing where directed at a level n exc 1.5m above the starting point complete all as specified and as directed

Spreading & Levelling and well ramming including watering as required in layers n.exc 25 cm thick complete all as specified and as directed

M&L hardcore of gauge n.exc 63mm deposited, spread and levelled in layers n.exc 15cm thick, watered and rammed to a true surface in broken stone or boulders complete all as specified and as directed

M&L for 40mm thick cement concrete (1:2:4) type B0 (using 12.5mm graded stone aggregate) as in flooring and finished surface even and smooth without using extra cement, complete all as specified and directed.

M & L for 75 mm thick Cement concrete 1:3:6 type C-2 (using 40 mm graded crushed stone aggregate) as in plinth protection finished even and fair complete all as specified and directed.

M&L for use & waste of rough finished flat Form work to sides of concrete foundations rafts, footing, base of columns, raft and raft beams, sides & soffits of foundation (if any) of foundation and plinth beams and similar work complete all as specified and directed.

M & L for Reinforced Cement Concrete Type M-25 (DESIGN MIX) using 20 mm graded granite stone aggregate) in foundations including rafts, footings, raft beam, plinth beams and mass concrete complete all as specified and directed.

M&L for use and waste of form work to sides and soffits of floor or roof beams, lintles, cantlevers, shelves incl supports etc for rough finished surface of concrete complete all as specified and directed.

M & L for Reinforced Cement Concrete Type M-25 (DESIGN MIX) (using 20 mm graded granite stone aggregate) in Beams, cantilevers, roof beams, lintels over 1.5 M span complete all as specified and directed.

Use & waste of rough finished Square, rectangular or polygonal Form work to sides of pillars, posts, struts, columns and stanchions complete all as specified and directed.

M & L for Reinforced Cement Concrete Type M-25 (DESIGN MIX) (using 20 mm graded granite stone aggregate) in Columns, piers, posts and struts complete all as specified and directed.

M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) rough finished surface complete all as specified and directed.

M&L for formwork to edges of concrete flats, treads, breaks in floors,window cills, concrete railings,openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide rough finished surfaces complete all as specified and directed.

M & L for Reinforced Cement Concrete Type M-25 (DESIGN MIX) (using 20 mm graded granite stone aggregate) in slabs supported on walls beams and columns in floors roofs, landings, balconies cannapies, deck slabs and in shelves and the like complete all as specified and directed.

M&L for mild steel TMT bars 10mm dia and over, cut to length bent to shap required including cranking, bending spirally for hooping for columnshooking ends and binding with and including mild steel wire (annealed not less than 0.9 mm dia or securing with clips complete all as specified and directed.

All as per Item No. 34 here in above but 5mm dia and over upto and incl 10 mm dia in spacers, stirrups and binders

M&L for brick work with old size fly ash brick straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and directed.

Damp rooof cousrse to horizontal or vertical surfaces including necessary formwork in 40mm thik cement concrete 1:2:4 type B-0 and allying evenly a coat of blown type bitumen at the rate of 1.50 kg per square metre and blinding with clean dry sand @ 0.05cum per sqm complete all as specified and directed.

M& L for applying three coats of white wash on plastered surfaces including preparing new surfaces plastered or unplasted of walls complete all as specified and directed.

M&L 10mm thick plastering in CM 1:4 with using WPC @ 3% by weight of cement, on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed. (NOTE : - WPC will be measured and paid separately)

S&F steel windows or ventilators with side hung shutters including projecting type hinges with steel handle and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

S&F 3 mm thick sheet glass ordinary quality and glazing with oil puty in square n.exc 0.5 sqm in each pane complete all as specified and directed.

M&L for pressed steel door frames of 125 x 60mm size with one or more rebates including necessary fixing lugs, hinges, locks, strike plate, etc complete as specified supplied and fixed complete all as specified and directed.

M&L 2nd class hard wood plain framed factory made panel shutter 35 mm thick (two or three panels) with lock rail and panel of 12mm veneered particle board with commercial veneering on both faces, the size of rail & style as per IS 1003 (Part-I) Kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F MS Butt hinges medium weight cold rolled of size 100mm complete all as specified and directed.

S&F MS barrel tower bolts of 200mm long stove enameled black with bright bolt complete all as specified and directed.

S&F MS pressed bow handle, oval type stove enameled black of size 150mm long complete all as specified and directed.

S&F mild steel sliding door bolts 300mm long plate stove enameled black with bright bolt not less than 12mm dia with and incl a minimum of 6 bolt and nut four on bolt plates and two on staple plate complete all as specified and directed.

M&L preparation of new surfaces of wood or wood based material description over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M & L for Two coats of synthetic enamel paint to new steel surfaces over 10cm width or girth including preparation of new surfaces and one coat of red oxide primer complete all as specified and directed.

GNV Engg Services

RAFEEQ AND CO

SAI RAM CONSTRUCTIONS

SM CONSTRUCTIONS

Palla Thrinatharao

PVRCS ENGINEERS

M/S Veerabhadra Constructions