Addition Alteration of M C Qtr allotted to Sh Khem Raj (Chowkidar) at Ram Bazar in ward No 14

Amount

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations and plinth in :cement mortar 1:4 (1 cement : 4 coarse sand)

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). Second Class Deodar wood

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Mild steel and Medium Tensile steel bars

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand) : 4 graded stone aggregate 20 mm nominal size)

15 mm cement plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix : 1:4 (1 cement: 4 fine sand)

white glazed tiles 6mm thick in wall tiles of steps and dedo 12mm thick cement mortar 1:3 ( 1 cement :3 sand) and jointed with cement slurry including carriage of material in all leads and lifts.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 300x300 mm

P/L 20mm thick granite stone for kitchen gas stand on 20mm thick cement mortar lead in 1:6 (1 : Cement 6: Sand)

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately) 40mm thick 2nd Class deodar wood

Centering and shuttering including strutting, propping etc. and removal of form work for : Retaining walls, return walls, walls (any thickness) including attached pilasters, buttresses, plinth and string courses fillets, kerbs and steps etc.

Providing wood work in trusses, purlins, rafters, posts, post plates, wall plates and the like wrought framed, hoisted and fixed in position. Pine wood

Providing and fixing ply wood lining with butt jointing and nails (frame work and cove fillets to be measured and paid for separately) 6 mm thick

Providing plain square edged 60x12mm in Pine wood

Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws : 35 mm thick shutters with ISI marked M.S. pressed butt hinges bright finished of required size Second class teak wood

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat with cement primer

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture wood and wood based surface

Providing and fixing ISI Marked M.S. bolt hinges 125x50x4mm

Providing and fixing M.S. tower bolt 100x100mm

Providing and fixing M.S. handle 125mm

P/F Stainless steel sliding door bolts 300x16mm

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :250x10 mm

Providing and fixing steel kitchen sink with G.I. Or M.S. Bracket 600x510mm

Providing and fixing washbasin with C.I. Brackets cutting and making the wall wherever require

Providing and fixing Vitreous china water closet squatting pan(english type WC pan ) size 580 mm (Earth work, bed concreate ,reset and trap to be measured and paid for seprately

Providing and fixing P.V.C. Low level flushing cistern with manually controlled device handle cover conforming to IS:7231, with all fitting and fixtures complete

Providing and fixing 600x450mm beveled edge mirror of superior glass of approved quality complete with 6mm thick hard board ground fixed to wooden with C.P. Brass screws and washers complete

Providing and fixing PTMT Towel nail complete with barckets fixed to wooden with C.P. Brass screws with conceated fitting arrangement of approved quality and colour

P/F S.S. Gratting (Jalli) 0.10mm thick

P/F Soap Dish of approved quality

P/F P.V.C. Seat cover for English seat

P/F M.S. Zet for English Sheets etc.

P/F P.V.C. P or S trap of 100mm dia of approved quality

Providing and fixing PVC water storage tanks syntax or equivalent i/c cost of connecting 500ltrs capacity storage PVC tank SINTEX

Providing and fixing P.V.C. Waste pipe for sink and washbasin i/c P.V.C. Waste fitting complete and 32mm dia

P/F C.P. Brass Angle cock 15mm dia (heavy duty)

P/F C.P. Brass piller cock of approved quality conforming to IS:8931:

P/F C.P. Brass bib cock of approved quality 15mm nominal bore

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore

Providing and fixing floating valve of approved quality high or low pressure, with plastic floats complete for water tank

P/L P.V.C. Pipe of 100mm dia (heavy duty)

P/L P.V.C. Door bend 100mm

P/F P.V.C. Plain bend 100mm dia of approved quality

P/L P.V.C. Door tee 100mm

P/L P.V.C. Collar 100mm

P/F gun metal gate valve with C.I. Wheel of approved quality

P/F G.I. Union in G.I. Pipe i/c cutting and threading the pipe and making long screws etc. 15mm nominal bore

P/F G.I. Pipe complete with G.I. Fitting and clamps i/c cutting and making good the wall

P/F G.I. Tee 15mm dia

P/F C.P. Extension nipple of 15mm dia

P/F P.V.C. Pipe 0.75mm thick

P/F P.V.C Plain Bend 75mm dia

P/F P.V.C. Door Bend 75mm dia

P/F P.V.C Tee 0.75mm thick

P/F P.V.C. Collar 0.75mm

P/F P.V.C. Cowl 0.75mm thick

P/L C.P.V.C. Pipe 15mm dia

P/L C.P.V.C. Tee 15mm dia

P/L C.P.V.C. Socket 15mm dia

P/L C.P.V.C. Connection pipe 15mm dia 45cm long with brass union

P/F C.P.V.C. union 15mm dia

Renewing glass panes, with putty and nails wherever necessary including racking out the old putty: Float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm)

Providing and fixing 19mm thick commercial board shutter for cup board etc. including nickel plated bright finished piano hinges. The rate is inclusive for carriagee of materials within all leads, lifts and other incidentals.

SHUBHAM CHAUHAN

YOGESH THAKUR