COMPR REPAIR OF B/R AND E M NATURE WK OF MD AND OTM ACCN INCL ROOF TRET, PERIODICALS, SHAFT REPAIR, SUNKEN TRET, PLASTER, JOINERY, SUMMER WINTER APPL, POINT WIRING ETC MGT SYS IN CARNATIC LINE AT DAMANA MIL STN UNDER GE JAMMU

Note - Rate quoted below all items of this schedule inclusive provision as under making arrangement for establishment of centralized complaint centre in the existing building as under :- (a) Contractor shall be given user id and password for accessing the online complaint portal and contractor shall at his own expense by himself or his representative feed the data in r/o complaints so generated. (b) Manually registered complaints shall be obtained everyday from MES complaint cell and rectification or otherwise shall be intimated to JE in charge of the cell for updation of manual registers. (c ) Provision and maintenance of all tools, plants, equipment and safely gear required for tradesmen under this contract (d) Provision of communication and conveyance (as required) facilities to supervisor and tradesmen. (e) Monitoring and management of complaints report from generation to execution of complaint including pending complaints. (f) Updating status of lodged complaints on a daily basis. (g) Basic inputs to be noted from the complainants will be locality, Building No, Qtr No, Name and Rank of complaint and exact nature of complaint and mobile No/ telephone (j) On lodging the complaint, the Complaint No will be assigned for reference . Also system should indicate an approximate time for repairs. Accordingly a corresponding complaint slip shall be generated by the system with all relevant info. Complaint slip should be printed in triplicate and to be handed over immediately to Supervisor who shall detail appropriate tradesmen for repair with required materials/store. One copy of complaint shall be retained in complaint centre and two copies with tradesmen.

(Day to day online/offline complaint B/R & E/M)

Supply and fixing in repairs 15mm bore Bib taps CP fancy type, cast copper, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

Supply and fixing in repairs 15 mm bore Bib taps long nose/long body, cast copper alloy CP fancy type with capstan head handle screwed down, screwed for brass, weight not less than 450 gms ferrule and fixed complete all as specified and directed.

Supply and fixing in repairs 15mm bore Bib taps fancy type, PTMT any colour high pressure screwed for iron pipe and fixed (Minimum weight 15mm 105gms)

Supply and fixing in repairs Angle cock with wall flange, cast copper alloy, chromium plated fancy type screwed for 15 mm iron pipe, complete all as specified and as directed.

Supply and fixing in repairs Wall mixer non telephonic shower arrangement with connecting legs and wall flanges, cast copper alloy, chromium plated, complete all as specified and as directed.

Supply and fixing in repairs 15mm bore Pillar taps, cast copper alloy fancy type with capstan heads, chromium plated screw down high pressure, screwed for iron pipe all as directed by Engineer in charge.

Supply and fixing in repais Central Hole Basin Mixer without Popup Waste System with 450mm Long Braided Hoses complete all as specified and as directed.

Supply and fixing in repairs Sink Mixer swan neck with Swinging Spout (Wall Mounted Model) with Connecting Legs & Wall Flanges complete all as specified and as directed.

Supply and fixing in repairs Sink Cock with Swinging Spout (Wall Mounted Model) with Wall Flange complete all as specified and as directed.

Supply and fixing in repairs Health faucet (ABS body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connection and fixed in position fixed in repairs complete all as specified.

Supply and fixing in repairs Jet spray CP with flexible pipe n.less than 90 cm long fixed to EWC suitable for 15mm bore complete all as specified and directed.

Supply and fixing in repairs Shower rose 125mm size, brass chromium plated with or without swivel joints any size including fixing to steel pipe of 15mm bore all as directed by Engineer in charge.

Supply and fixing in repairs Urinal spreader of chromium plated for fixing with 15 mm dia pipe.

Supply and fixing in repairs Plastic water closet seat cover, white closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device complete all as specified and directed.

Supply and fixing in repairs Tubular towel rail brass chromium plated 20mm dia, D type, 60cm long between flanges. complete all as specified and as directed.

Supply and fixing in repairs Towel ring, Chromium plated, 200mm dia complete all as specified and as directed.

Supply and fixing in repairs Towel rack 600mm long with lower hangers, chromium plated,Stainless steel complete all as specified and as directed.

Supply and fixing in repairs Toilet paper holder fancy type , steel chromium plated approximate size 140X140X50mm complete all as specified and as directed.

Supply and fixing in repairs Soap dish steel chromium plated 100 mm size complete all as specified and directed.

Supply and fixing in repairs Brass face/Spindle as per sample for CP/Brass Bib tap, Angle/Stop cock, Pillar cock, wall mixer, WHB mixer, concealed stop cock etc for 15 mm bore pipe complete all as specified and as directed by Engineer-in-charge.

Supply and fixing in repairs Flushing cistern syphon kit for PVC cistern capacity 10 lit. complete all as specified and as directed by Engr-in-Charge.

Supply and fixing in repairs PVC syphon kit for one piece water closet with cistern of any capacity inclg float valve washer, push button etc complete all as spd and diriced

Supply and fixing in repairs Waste coupling 40mm dia for sinks, basins, etc. of chromium plated brass with long screwed shank and fly nuts complete all as as specified and as directed.

Supply and fixing in repairs Waste coupling 32mm dia for sinks, basins, etc. of chromium plated brass with long screwed shank and fly nuts complete all as as specified and as directed.

Supply and fixing in repairs CP Grating, lock type plain/hole size 100 mm dia including embeding in tiles with white cement complete all as specified and as directed.

Supply and fixing in repairs PVC connection 450mm long of 15mm bore with pair of brass check nuts , all as specified and directed.

Supply and fixing in repairs PVC connection 600mm long of 15mm bore with pair of brass check nuts , all as specified and directed.

Supply and fixing in repairs PVC Waste pipe 32mm bore of required length complete all as specified and as directed.

Supply and fixing in repairs PVC Waste pipe 32/40mm dia for urinal of required length complete all as specified and as directed.

Supply and fixing in repairs Vitreous china Pedestal type water closet white, with 'P' or 'S' trap including self closing seat cover, closed pattern with flat bottom,complete all as specified and as directed.

Supply and fixing in repairs Vitreous china Water closet pedestal pattern cascade type (one piece) with in built flushing cistern and seat cover with complete fitting complete all as specified complete all as specified and as directed.

Supply and fixing in repairs Vitrous china WC Orissa pattern white with integral foot rest 580x 440 mm including PVC P-trap, & PCC bedding in 1:2:4 and making good disturbed floor connecting to trap and flush pipe compete all as specified.(Rate of including in taking out and removal of old WC seat unhygienic condition) complete all as specified and as directed.

Supply and fixing in repairs PVC valveless, syphonic action type, flushing cistern, low level,white with inlet, ball valve, float and handle including brackets, PVC 32 mm 'L' bend of capacity 10.0 litres and making good to dismantled/damaged floor/surfaces, fixing in repair, complete all as specified and as directed by Engineer-in-charge.

Supply and fixing in repair Vitreous china urinal, half stall type, white (minimum),with including 32mm bore PTMT Waste coupling and PVC connection pipe of 15mm x 450mm long and PVC waster pipe 32mm bore

Supply and fixing in repairs Vitreous China bowl urinal flat back, with grating and union for discharge pipe including including 32mm bore PTMT Waste coupling, PVC connection pipe of 15mm x 450mm long and 32mm PVC Waste pipe

Supply and fixing in repairs Vitreous China Wash hand basin, Table top size 550x400x140mm, including 32mm bore PTMT Waste coupling, PVC connection pipe of 15mm x 450mm long and 32mm PVC Wast pipe complete all as specified and directed.

Supply and fixing in repairs Vitreous China Wash Hand Basins, size 550X400 mm (Flat Back or Angle Back type) including 32mm bore PTMT Waste coupling , waste pipe and PVC connection pipe of 15mm x 450mm long, a Pair of Angle iron Brackets duly Painted/Erecting Stand including Cutting and Pinning in Ends, Making Good Disturbed Surfaces in Cement Mortar 1:3, complete all as specified and as directed

Supply and fixing in repairs Vitreous china Pedestal for Wash Hand Basins complete all as specified and as directed

Supply and fixing in repairs Sinks with drainage board made of stainless steel 1.00mm thick kitchen or laboratory with plugs,washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete with CP waste coupling & PVC waste pipe complete all as specified and directed by Engineer-in-charge.

Supply and fixing in repairs Kitchen stainless steel plate rack made out of 1.00mm thick sheet and having partions as per sample. The over all size (39"x30"x10") fixed with steel fastners or steel screw complete all as specified and as directed.

Supply and fixing in repairs Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and as directed.

Supply and fixing in repairs Corner Glass Shelf 5.5 mm thick (300x300mm) chromium plated guard and railing(with Bracket) as per directed by Engr-in-charge.

Supply and fixing in repairs 500 litre capacity rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) three layers hoisted and fixed in position including 20 mm float valve (PVC) and 02 no's GI tank nipple complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in repairs 1000 litre capacity rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) three layers hoisted and fixed in position including 20 mm float valve (PVC) and 02 no's GI tank nipple complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in repairs Ball valves/float valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe of 20 mm bore pipe including making connections complete all as as specified and fixed (Minimum weight 20mm-210 gms).

Supply and fixing in repairs Ball valves/float valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe of 25 mm bore pipe including making connections complete all as as specified and fixed (Minimum weight 20mm-210 gms).

Supply and fixing in repairs PVC over head tank cover / lid of size suitable for capacity of above 500 litres and upto 1000 litres capacity complete all as specified and directed.

Supply and fixing in repairs Galvanised Tubes, medium grade, 15 mm bore, ISI marked with all fitting such as bends, tees,elbows, unions,short pieces, connectors, back nuts etc and fixed complete to walls and ceilings or laid in floors, complete all as specified and as directed by Engineer-in-charge

Supply and fixing in repairs Galvanised Tube fittings, medium grade, 15 mm bore, such as bends, tees, elbows, unions, short pieces,connectors, back nuts, etc complete all as specified and as directed

Supply and fixing in repairs Galvanised Tubes, medium grade, 20 mm bore, ISI marked with all fitting such as bends, tees,elbows, unions,short pieces, connectors, back nuts etc and fixed complete to walls and ceilings or laid in floors, complete all as specified and as directed by Engineer-in-charge

Supply and fixing in repairs Galvanised Tube fittings, medium grade, 20 mm bore, such as bends, tees, elbows, unions, short pieces,connectors, back nuts, etc complete all as specified and as directed

Supply and fixing 20mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, Tee short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) inlcuding taking down 15mm steel tubing complete all as specified.

Supply and fixing in repairs CPVC brass elbow 20 mm outer dia all complete all as specified and as directed.

Supply and fixing in repairs CPVC brass elbow 20 mm outer dia (3/4x1/2) all complete all as specified and as directed.

Supply and fixing in repairs CPVC brass Tee 20 mm outer dia all complete all as specified and as directed.

Supply and fixing in repairs CPVC male brass threaded adapter 20 mm dia (MTA/MBTA) complete all as specified and as directed.

Supply and fixing in repairs CPVC female brass threaded adapter 20 mm dia. (FTA/FBTA) complete all as specified and as directed.

Supply and fixing 25mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, Tee short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) inlcuding taking down 20mm steel tubing complete all as specified.

Supply and fixing in repairs 25mm outer dia CPVC gate valves all as directed by Engineer in charge.

Supply and fixing in repairs 20 mm dia Gun metal, globe or gate valve with iron wheel head,screwed both ends for iron pipe complete all as specifed and dicrected.

Material and labour for Cleaning of water storage tank 500 litres capacity completely by removing all scale dirt / dust of any description with chlorine complete all as directed at site including taking down and refixing of tank at the same place, any damage will be rectified by the contractor at his own risk and cost all as directed.

Material and labour for Cleaning of water storage tank 1000 litres capacity completely by removing all scale dirt / dust of any description with chlorine complete all as directed at site including taking down and refixing of tank at the same place, any damage will be rectified by the contractor at his own risk and cost all as directed.

Supply and fixing in repairs 110mm bore PVC (SWR) pipes single socketed in any length with rubber joints fixed to floor etc complete.

Supply and fixing in repairs 75mm bore PVC (SWR) pipes single socketed in any length with rubber joints fixed to floor etc complete.

Supply and fixing in repairs 110mm bore PVC (SWR) pipes single socketed in any length with rubber joints fixed to walls etc complete.

Supply and fixing in repairs 75mm bore PVC (SWR) pipes single socketed in any length with rubber joints fixed to walls etc complete.

Supply and fixing in repairs 75 mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement including jointing to waste pipe fixed in cement concrete B1 (1:2:4) complete all as specified and directed.

Supply and fixing in repairs PVC (SWR) Bends 110mm bore any radius with access door

Supply and fixing in repairs PVC (SWR) Bends 75 mm bore any radius with access door

Supply and fixing in repairs PVC (SWR) Tee 110mm bore any radius with access door

Supply and fixing in repairs PVC (SWR) Tee 75 mm bore any radius with access door

Supply and fixing in repairs PVC (SWR) vent cowl 110mm bore

Supply and fixing in repairs PVC (SWR) vent cowl 75mm bore

Taking down shutters of any description n exc 1 sqm each and refixing in the same opening after easing and adjusting complete all as specified and as directed.

Taking down shutters of any description exc 1 sqm but n.exc 2 sqm each and refixing in the same opening after easing and adjusting complete all as specified and as directed.

Supply and fixing in repairs medium weight, cold rolled with galvanized mild steel Butt hinge, anodized, 75mm size.

Supply and fixing in repairs medium weight, cold rolled with galvanized mild steel Butt hinge, anodized, 100mm size

Supply and fixing in repairs 30mm wide flap (when open) SS Continuous (piano) hinges, bright finish or electro galvanised fixed to Kitchen cuboard complete all as specified and directed.

Supply and fixing in repairs Modular Auto concealed soft closed hinges 35mm, any degree size fixed to cupboard complete all as specified and as directed.

Supply and fixing in repairs extruted Aluminium alloy handles fabricated type anodised 150 mm long complete all as specified and directed.

Supply and fixing in repairs extruted Aluminium alloy handles fabricated type anodised 125 mm long complete all as specified and directed.

Supply and fixing in repairs 150 mm long aluminium anodised barrel tower bolt of extruted section complete all as specified and directed.

Supply and fixing in repairs 200 mm long aluminium anodised barrel tower bolt of extruted section complete all as specified and directed.

Supply and fixing in repairs 300 mm long dia aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) & fixing clips of sheet, cast or extruded section & fixing blots & sliding bolts of extruded section complete all as specified and directed.

Supply and fixing in repairs Floor door stopper of aluminium alloy body and tongue 140 mm anodised with hard drawn steel spring fixed in floor complete all as specified and directed.

Supply and fixing in repairs mild steel Helical door spring of size 300 mm at site including welding to steel chowkhats, complete all as specified and directed.

Supply and fixing in repairs 100 mm hasp and staple safety type aluminuium anodised including bolt to hinge plate and fixed with screw complete all as specified and directed.

Supply and fixing in repairs 40 mm dia cupboard knobs fixed with nut and washer brass polished bright finished complete all as specified and directed.

Supply and fixing in repairs Magnet catcher 50 mm size for kitchen cupboard shutter complete all as specified and directed.

Supply and fixing in repairs Curtain rod of stainless steel 20mm dia and side capes fixed in position by drilling holes in walls and fixed the brackets with rawl plug and steel screw complete all as specified as directed by Engineer-in-Charge

Supply and fixing in repairs Drapery Curtain rod of metalic 20mm dia covered with PVC coating including MS bracket, end ball, rounded block (coated with brown/cherry/golden colour) of approved pattern and shade fixed in position by drilling holes in walls and fixed the brackets with rawl plug and steel screw complete all as specified and directed.

Supply and fixing in repairs MS Peg set of six powder coated as approved by GE complete all as specified and directed.

Supply and fixing in repairs Aluminium extruded section body, door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed.

Supply and fixing in repairs Double action floor spring hydraulically regulated, made of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, govrning pivot made of brass, other parts made of mild steel heavy duty and including taking down aluminium door shutter and refixing complete all as specified and directed.

Supply and fixing in repairs Mild steel Mortice lock verticle type, size 100mm long with 4 levers complete all as specified and as directed.

Supply and fixing in repairs 18mm thick single layered HDHMR coloured / textured finish board density more than 850 Kg / cum smooth finished fixed in cupboard and jointed together with necessary adhesive complete all as per directions by Engineer-in-Charge, manufacturer’s specification complete all as specified and as directed

Supply and fixing in repairs 18mm thick factory made 100% solid WPC flush shutter (for cupboard and vanity etc) made from co-extruded three layer rigid foam sheet (single extruded) with 0.8 to 1 mm thick outer layer having density not less than 1400 kg/cum and density of central core not less than 600 kg/cum manufacturer by an ISO 9001/2015 certified company complete all as specified and directed.

Hacking out old broken glass panes(any thickness, size,quality or description) from wooden/steel frames, glazed with putty or fixed with beads complete all as specified and directed. (Including all necessary scaffolding lifiting arrangement up to 10 mtr height).

Supply and fixing 4.8mm thick Sheet glass, ordinary quality and glazing with oil putty in any size, all as specified and directed.

Supply and fixing 3mm thick Sheet glass, orinary quality and glazing with oil putty in any size, all as specified and directed (Including all necessary scaffolding lifiting arrangement up to 10 mtr height).

All as per Srl Item No 105 above but figured glass, Pin head type

Supply and fixing in repairs Galvanised mild steel wire cloth 0.56 mm nominal dia or wire and average width of aperture 1.0 mm and fixed with tinned tacks or galvanised wire staple complete all as specified and directed.

Material and labour for Spot/Running welding to loose gate/ window hinges, tower bolt, handle, stay etc. after taking down & refixing in same position and making good welded area as per exsiting. Complete all as spd and directed.

Supply & fixing in repairs switch piano, flush type single pole one way 5Amp, 240 volts ISI marked complete all as specified and directed .

Supply & fixing in repairs Socket outlet 2 in 1, 3 pin, 5A complete all as specified and directed .

Supply & fixing in repairs Switch socket outlet combined 5 pin 5 amp flush type , 240 volts ISI marked complete all as specified and directed.

Supply & fixing in repairs Switch socket outlet combined 2 in 1 , 3 pin 5 amp and 15 amp flush type , 240 volts ISI marked complete all as specified and directed.

Supply & fixing in repairs Socket outlet 5 pin, 15 Amp, flush type, 240 Volts, 6 pin flush type complete ISI marked complete all as specified and directed.

Supply & fixing in repairs switch piano, flush type single pole one way 15 Amps, 240 volts ISI marked complete all as specified and directed .

Supply and fixing in repairs Modular switch 1 way 6A,1 module , 240 volts ISI marked complete all as specified and directed

Supply and fixing in repairs Modular switch 1 way 16A, 1 module , 240 volts ISI marked complete all as specified and directed

Supply and fixing in repairs Modular Socket, 6A - 2/3 pin combined 2 module, , 240 volts ISI marked complete all as specified and directed

Supply and fixing in repairs Modular Socket 6A/16A - 2/3 pin combined 2 module, , 240 volts ISI marked complete all as specified and directed

Supply and fixing in repairs Modular Fan step regulator, 120W 1 module , 240 volts ISI marked complete all as specified and directed

Supply and fixing in repairs modular white cover plate with frame 3 module complete all as specified , 240 volts ISI marked complete all as specified and directed

Supply and fixing in repairs modular white cover plate with frame 4 module complete all as specified , 240 volts ISI marked complete all as specified and directed

Supply and fixing in repairs modular white cover plate with frame 6 module complete all as specified , 240 volts ISI marked complete all as specified and directed

Supply and fixing in repairs modular white cover plate with frame 8 module complete all as specified , 240 volts ISI marked complete all as specified and directed

Supply and fixing in repairs modular white cover plate with frame 12 module complete all as specified , 240 volts ISI marked complete all as specified and directed

Supply and fixing in repairs distribution board sheet steel powder coated for MCB with copper bus bar and neutral link earthing stud SPN 8 way 240 volts double door complete all as directed by Engr-in-Charge. Note:- Distribution board and MCBs should be same make.

Supply and fixing in repairs distribution board sheet steel powder coated for MCB with copper bus bar and neutral link earthing stud SPN 6 way 240 volts double door complete all as directed by Engr-in-Charge. Note:- Distribution board and MCBs should be same make.

Supply and fixing in repairs distribution board sheet steel powder coated for MCB with copper bus bar and neutral link earthing stud SPN 4 way 240 volts double door complete all as directed by Engr-in-Charge. Note:- Distribution board and MCBs should be same make.

Material and labour of distribution board, double door, made of 2mm thick stainless steel sheet, powder coated for MCB with copper bus bar and neutral link earthing stud SPN 12 way 240 volts double door complete all as specified and as directed by Engineer-in-Charge. Note: - Distribution board and MCB's should be of same make.

Supply and fixing in repairs 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 AMP, in the MCB DB Complete with connection testing and commissioning.

Supply and fixing in repairs 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 40 AMP, in the MCB DB Complete with connection testing and commissioning.

Supply and fixing in repairs SPN 32 Amp rating 240V, 10KA 'B' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning.

Supply and fixing in repairs SPN 40 to 63 Amp rating 240V, 10KA 'B' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning.

Supply & fix in repairs calling bell ding dong/buzzer ,AC 230Volts single pole complete all as specified and directed.

Supply & fix in repairs stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. complete all as specified and directed.

S & F in repairs for bell push , flush type single pole , 5Amp, 240 volts all as specified .

Supply and fixing in repairs Ceiling Rose 3 terminal surface type Complete all as directed.

M& L in repairs for Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings

M& L in repairs Self ballast LED retrofit Lamp with PVC body and PC Diffuser 9 watt 230 Volt 6500K Complete all as directed.

Supply and fixing in repairs LED lights fitting 1x 20W, 220V, Batten type complete with LED tube rod 20 watts driver, holder and power factor >0.95 , 100 Lumen/Watt, 6500 K cool day type conforming to ISI including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete. (4' ft long ) with LED rod 20 watt, 230 Volts 50 Hz.

Supply and fixing in repairs LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete.

Supply and fixing in repairs bulk head luminaries IP65 with opal diffuser 10 watt, 230 Volts LED type complete with 10 watt LED Bulb all as directed Engr-in-Charge.

Supply and fixing in repairs copper cable for circuit with proper existing colour coding, insulated, unsheathed,multistranded, copper conductor FRLS, cable of 2.5 Sqmm for phase and neutral, drawn through the existing rigid PVC concealed conduit fixed on wall including taking down existing unserviceable wiring complete all as specified and as directed.

Supply and fixing in repairs copper cable for circuit with proper existing colour coding, insulated, unsheathed,multistranded, copper conductor FRLS, cable of 1.5 Sqmm for phase and neutral, drawn through the existing rigid PVC concealed conduit fixed on wall including taking down existing unserviceable wiring complete all as specified and as directed.

Supply and fixing in repairs plug top 15 Amps complete all as specified and directed.

(Periodical Services)

Material and labour for Complete removal of existing treatment and preparation of ceiling and applying two coats of distemper oil bound over primer coat, complete all as specified and as directed by Engineer in charge.

Material and labour for Preparation of Old decorated surface and applying one coat of Oil Bound Distemper on Ceilings complete all as specified and as directed.

Material and labour for Complete removal of existing treatment and preparation of surface and applying 1mm thick wall care putty on old surface of walls and applying two coats of distemper Oil bound over primer coat, complete all as specified and as directed by Engineer in charge.

Material and labour for Preparation of Old decorated surface and applying one coat of Oil Bound Distemper on Walls complete all as specified and as directed.

Material and labour for Preparation of Old painted surface of Wood and wood based materials of any description and applying one coat of synthetic enamel paint over 10cm width or girth complete all as specified and as directed. (Including all necessary scaffolding lifiting arrangement up to 10 mtr height).

Material and labour for Preparation of Old painted surface of Steel of any description and applying one coat of synthetic enamel paint over 10cm width or girth complete all as specified and as directed. (Including all necessary scaffolding lifiting arrangement up to 10 mtr height).

Material and labour for Complete removal of existing treatment on wall, chajja, roof projection and roof fascia surface and finishing surface with Acrylic Smooth exterior paint of required shade (Two or more coat applied @ 1.67 ltr/10 sqm over and including Two or more coat priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified and as directed. (Including all necessary scaffolding lifiting arrangement up to 10 mtr height).

Complete removal of existing treatment including fascias, cornices etc by scrapping with mechanical wall sander (having mechanical vacuum mechanism) having RPM not less than 1500, sanding pad of 80 Grit having dia of 7"/9" to make the surface free from dust, loose paint and loose plaster to be completely removed by skilled labour and repair of external wall/Chajjas to be done with repair mortar to get even surface including preparation of old surface of wall/ceiling by filling cracks by Berger Bison Putty / crack fill paste of Berger Paints or equivalent make and make good smoothen surface by sand paper and applying two coats of premium acrylic smooth exterior emulsion of approved colour with silicon additive & Color stay Technology ,Excellent Dirt Pick up resistance of Berger Paints Ltd or equivalent of other approved make with low VOC less than 50 gram/ litre as per the LEEDS specifications, Anti Algal properties in two coats @ 1.79 ltr (undiluted)/ 10 sqm diluted with water as per manufacturer instructions applied over one coat of acrylic water based exterior grade primer @ 0.9ltr(undiluted)/10 sq mtrs diluted with water in 1:1ratio and 1mm thick exterior grade wall putty as per manufacture's instruction and all coats incl primer to be applied with fully automatic airless spray machine of paint application with a flow speed of minimum 1 ltr per minute having a pressure of 3300 PSI all as specified and directed.Allow 6-8 hrs to dry the surface in subsequent coats of paint and including necessary scaffolding at any height complete all as specified and as directed Make: Berger Paints Weathercoat Long Life Flexo / Nerolac Paints excel Total / Asian Paint Apex Ultima Suprema.

Srl Item No 153 Contd/.... Note :- (a) Work shall be done as per 'Memorandum of Understanding' (MOU) between tenderer and manufacturer of paints and their authorized applicator complete all as specified and directed. (b) The contractor shall upload 'Memorandum of Understanding' (MOU) between tenderer and manufacturer of paints and their authorized applicator after conclude of tender and before place of Work Order Documents as mentioned in NIT. (c) The work pertaning to periodical services & water proofing shall be executed from authorized applicator through manufacturer of which the material i.e.paint, distemper, cement base paint, putty etc. is proposed to be used by the contractor and approved by GE.

(Joinery)

Taking down shutters of any description n.exc. 1.00 sqm each and removing from the site complete all as specified and directed.

Taking down shutters of any description exc 1.00 Sqm and n.exc. 2.00 sqm each and removing from the site complete all as specified and directed.

Taking down chowkats or frames n. exc. 1.5 sq.m each with shutters9 without taking off shutters from the frame) complete all as specified and directed

Taking down Chowkats or frames exc 1.5 sq.m but n.exc 4 sqm each each with shutters (without taking off shutters from the frames) complete all as specified and directed.

Supply and fixing Pressed steel frames (factory made) made out of 1.25 mm thick black MS sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete size of frame 105x60mm incl bottom of each chowkat to be welded with 2 Nos 25x25x3mm thick flat iron projecting 10 cm on either side complete all as specified and directed.

All as per Item No 160 above but size of frame 125X60mm for fixing of two shutters complete all as specified and directed.

Supply and fixing Pressed steel frames for cup board chwokhat of size 60x40mm with one or more rebates incl necessary fixing lug, hold fasts etc complete all as specified and directed.

Material and labour Cement concrete (1:3:6) type C0 using 12.5mm graded stone aggregate filling in pressed steel chowkats bed block for holdfast and the like complete all as specified and directed.

Supply and fixing 35mm thick 2nd class HW Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete, all as specified and directed by Engr-in-Charge.

Supply and fixing 35mm thick 2nd class hard wood factory made glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.20 (a) complete all as specified and directed.

Supply and fixing Flush shutters, 30 mm thick solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

Material and labour for Preparing surface of new wood and wood based material of any description and girth, not otherwise described and treated with two coats of synthetic enamel paint complete all as specified and directed.

Material and labour for Preparing surface of new steel of any description over 10cm width and girth, not otherwise described and treated with two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

Supply and fixing Factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other Frames/Chowkhat of size 45 x 70 mm ( +5 mm) comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate andnatural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge

Supply and fixing Factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with Butt hinges of required size with necessary full body threaded star headed counter sunk screws, all as per direction of Engineer- In- Charge. (Note: Butt hinges and necessary screws shall be paid separately)

Supply and fixing 18mm thick single layered HDHMR coloured / textured finish board density more than 850 Kg / cum smooth finished fixed in cupboard and jointed together with necessary adhesive complete all as per directions by Engineer-in-Charge, manufacturer’s specification complete all as specified and as directed

Supply and fixing 18mm thick factory made 100% solid WPC flush shutter (for cupboard and vanity etc) made from co-extruded three layer rigid foam sheet (single extruded) with 0.8 to 1 mm thick outer layer having density not less than 1400 kg/cum and density of central core not less than 600 kg/cum manufacturer by an ISO 9001/2015 certified company complete all as specified and directed.

Supply and fixing in repairs Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge.

Supply and fixing in repairs Aluminium powder coated door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, handles 2 Nos. in each door, hinges, screws etc. complete all as specified and directed.

Supply and fixing in repairs Aluminium powder coated window and ventilator, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified and directed.

Supply and fixing in repairs Aluminium powder coated window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and directed.

Supply and fixing in repairs Aluminium powder coated three track sliding type glazed window,shutter with 5mm thick plain sheet glass fixed open track section 100x38x1.4 mm having three track (two of 4.8 mm thick glass & one of stainless steel wirecloth of 0.56 mm dia and 1.0 mm aperture) with members of window shutters of section 38x12mm including aluminium grill 75 mm x 5.50 mm thick pitch diamond shape, wire gauge and grill shall be fixed with the help of 40 mm aluminium flat and other standard Bombay sliding section incl all necessary fiber wheel rollers suitable handle to facilitate sliding and all necessary jointing cleats glazing clips,rubber packing, Aluminium snap beeding etc complete all as specified and directed.

Material and labour 4.8mm thick Sheet glass ordinary quality complete with aluminium beads in any size, all as specified and directed

Supply and fixing in repairs 12mm Toughned glass as in hinged doors, partitions automatic doors and similar work including cutting to shape, drilling holes required.

Supply and fixing Glass Door handle stainless steel 450mm Length, 30mm dia for 12mm thick toughned glass door shutter.

Supply and fixing Glass Door lock Stainless steel for 12mm thick toughned glass door shutter.

Supply and fixing Galvanised mild steel wire cloth 0.56 mm nominal dia or wire and average width of aperture 1.0 mm and fixed with tinned tacks or galvanised wire staple complete all as specified and directed.

Supply and fixing 100 mm size mild steel Butt hinges medium weight cold rolled complete all as specified and directed.

Supply and fixing 100 mm hasp and staple safety type aluminuium anodised including bolt to hinge plate and fixed with screw complete all as specified and directed.

Supply and fixing 30mm wide flap (when open) SS Continuous (piano) hinges, bright finish or electro galvanised fixed to Kitchen cuboard complete all as specified and directed.

Supply and fixing Modular Auto concealed soft closed hinges 35mm, any degree size fixed to cupboard complete all as specified and as directed.

Supply and fixing Magnet catcher 50 mm size for kitchen cupboard shutter complete all as specified and directed.

Supply and fixing Extruded Aluminium alloy handles fabricated type anodised 150 mm long complete all as specified and directed.

All as per item No 189 above but 125 mm long complete all as specified and directed.

Supply and fixing 150 mm long aluminium anodised barrel tower bolt of extruted section complete all as specified and directed.

All as per item No 191 above but 200mm long complete all as specified and directed.

Supply and fixing 300 mm long dia aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) & fixing clips of sheet, cast or extruded section & fixing blots & sliding bolts of extruded section complete all as specified and directed.

Supply and fixing Floor door stopper of aluminium alloy body and tongue 140 mm anodised with hard drawn steel spring fixed in floor complete all as specified and directed.

Supply and fixing Mild steel Helical door spring of size 300 mm at site including welding to steel chowkhats, complete all as specified and directed.

Supply and fixing 40mm dia cupboard knobs fixed with nut and washer brass polished bright finished complete all as specified and directed.

BLANK

Supply and fixing Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

(Leakage/Seepage and certain other misc works)

Taking down Cement Plaster of any description on Brick Walls, Concrete Surfaces including Racking out Joints, hacking for Key, scrubbing down with Water, etc. complete removal of debris outside MD land. (Including all necessary scaffolding lifiting arrangement up to 10 mtr height).

Material and labour for Rough cast plaster on fair faces of brick work or concrete surface complete all as specified and as directed by Engineer in charge.

Material and labour for Rendering 5mm thick on fair faces of concrete surface of ceiling in CM 1:3, surface finished even and smooth surface without using extra cement complete all as specified and directed.

Material and labour for Rendering 10mm thick on fair faces of brick work or concrete surface in CM 1:6 surface finished even and smooth without using extra cement complete all as specified and directed.

Material and labour for Rendering 15mm thick in CM 1:4 in on fair faces of brick surface finished even and fair including water proofing compound all as specified. (Including all necessary scaffolding lifiting arrangement up to 10 mtr height).

Material and labour for Preparing of New plastered surface of ceiling and applying two coats of distemper oil bound over primer coat, complete all as specified and as directed by Engineer in charge.

Material and labour for Preparing of New plastered surface of wall and applying 1mm thick wall care putty and applying two coats of distemper oil bound over primer coat, complete all as specified and as directed by Engineer in charge.

Material and labour for Preparing of New plastered surface of wall, chajja, roof projection and roof fascia surface and finishing surface with Acrylic Smooth exterior paint of required shade (Two or more coat applied @ 1.67 ltr/10 sqm over and including Two or more coat priming coat of exterior primer applied @ 2.20 kg/10 sqm) over 1mm thick exterior wall care putty complete all as specified and as directed. (Including all necessary scaffolding lifiting arrangement up to 10 mtr height).

Dismantling unframed work timber scantling 40 Sqcm and over in section in any position as in unframed work complete all as specified and as directed.

Supply and fixing Structural steel works of Fe 410W (Gde E 250) quality B, as in Roof trusses (framed), trussed, purlins, posts, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel, tube or flat sections) including distance pieces, cleats etc.

Dismantling AC corrugated, semi corrugated sheets in roof covering including ridge complete all as specified and as directed.

Supply and fixing Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 MPs as in roof covering fixed with self tapping screws or L-type or J-type or cranked hook bolts complete all as specified and as directed.

Supply and fixing Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 MPs as in ridge of roof fixed with self tapping screws or L-type or J-type or cranked hook bolts complete all as specified and as directed.

Material and labour for Preparing surface of new steel of any description over 10cm width and girth, not otherwise described and treated with two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

Dismanting floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store & rubbish off the premises complete all as specified and directed.

Material and labour for Vitrified tiles any colour 8mm thick (square/rectangular) polished as in floor, area of each tile n.exc 0.36 sqm, set and jointed and laid with 3-4mm spacers set and jointed in neat Polymer modified tile adhesive of appropriate grade as per manufacturar instructions, 15mm thick screed bed in CM 1:6 & pattern, laying etc of tiles and Shade, Colour shall be decided by Engr in Charge complete all as specified.

All as per item No 215 above but in vertical surfaces with 3-4mm spacers set and jointed in neat Polymer modified tile adhesive of appropriate grade as per manufacturar instructions , 15mm thick backing coat in CM 1:4 complete all as specified

Material and labour for Non - skid coloured Ceramic tiles 6 to 7 mm thick (square/ rectangular) as in floor, area of each tile n.exc 0.18 sqm, set and jointed and laid with 3-4mm spacers set and jointed in neat Polymer modified tile adhesive of appropriate grade as per manufacturar instructions , 15mm thick screed bed in CM 1:6 complete all as specified and as directed by Engr-in-Charge.

All as per item No 217 above but in vertical surfaces including laid with 3-4mm spacers set and jointed in neat Polymer modified tile adhesive of appropriate grade as per manufacturar instructions complete all as specified

Material and labour for Non - skid coloured Ceramic tiles 6 to 7 mm thick (square/ rectangular) as in floor, area of each tile n.exc 0.11 sqm, set and jointed and laid with 3-4mm spacers set and jointed in neat Polymer modified tile adhesive of appropriate grade as per manufacturar instructions 15mm thick backing coat in CM 1:4 complete all as specified and as directed by Engr-in-Charge.

Material and labour for Coloured glazed ceramic tiles glossy finish of size 450x300x 5-6mm thick in dado’s/skirting etc. laid with 3-4mm spacers set and jointed in laid with 3-4mm spacers set and jointed in neat Polymer modified tile adhesive of appropriate grade as per manufacturar instructions to match, pattern, laying etc of tiles incl 10 mm thick CM 1:4 plaster and Shade, Colour shall be decided by Engr in Charge complete all as specified.

Dismantling Stone slabs laid dry and tiles of any description or thickness in floors, aprons etc. and rubbish off the premises complete all as specified and as directed.

Material and labour for Machine cut kota stone slab flooring 18-20mm thick as in floor to match the shade of the slab including 20 mm screed bed CM 1:6 including rubbing polishing complete all as specified and directed.

Supply and fixing for Machine cut kota stone slab 18-20mm thick over 10 mm thick as in vertical surface over rendering in CM 1:4 laid and jointed with grey cement slury mixed with pigment to match the shade of the slab incluiding rubbing and polishing complete all as specified and directed by Engineer –in-Charge.

Material and labour for Coloured Chequered tiles of size 30cmx30cmx 25mm thick set, jointed and pointed in neat cement slurry in floors with grey pigment cement & pigment etc and Screed bed or bedding layer of mortar 20mm thick (1:4) for laying floor finishes as specified and as directed.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete

Material and labour for 15mm-16mm granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and incl Screed bed or bedding layer of mortar 20mm thick in CM 1:4 complete all as specified and directed.

Providing edge moulding to 15mm-16mm thick Granite stone of counters vanities etc. including machine polishing to edge to give high gloss finish etc. complete all as specified and directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for and complete removal of debris outside MD land.

Material and labour for PCC 1:2:4 type B0 (12.5mm graded stone aggregate) 25mm thick, as in sub base complete all as specified and directed.

Material and labour for PCC 1:3:6 type C2 (40mm graded stone aggregate) 75mm thick, as in plinth protection/path/ Hardstanding finished even and fair all as specified.

Material and labour for PCC 1:4:8 type D2 (40mm graded stone aggregate) 75mm thick as sub-base floor complete all as specified and directed.

Material and labour for PCC 1:2:4 type B1 (20 mm graded stone aggregate) as in coping including weathering, slightly rounded or chamfered angles and including necessary form work complete all as specified and directed.

Material and labour for PCC 1:2:4 type B1 (20mm graded stone aggregate) in roof padding, roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and directed.

Material and labour for Providing water proofing treatment to Sunken floors all as given below :- (a) Making fillet of size 25mm x 25mm at corner of slab and wall with polymer modified cementitious (PMC) mortar consisting of one part of tapecrete P-151, two parts of cement and 6 parts of fine sand by weight. (b) Sealing of joints of pipe with epoxy putty or epoxy mortar. (c) Cleaning the concrete surface by brushing & watering and applying a coat of tapecrete P-151 Acrylic Polymer Modified cementitious slurry consisting of one part of Acrylic based polymer modified cementitious flexible compostie coating and two parts of cement by weight. The coating shall be carried out upto 300mm above FFL and shall be allowed to dry for 4-6 hours. (d) Appying a coat of Acrylic based polymer modified cementitious flexible compostie coating brush topping 1.5mm thick consisting of one part of Acrylic based polymer modified cementitious flexible compostie coating, two parts of cement and two parts of silica sand by weight and cured to 2 days. (e) Applying 15mm thick plaster in CM 1:4 mixed with WPC @100ml per 50 Kg cement on treated surface. (f) PCC 1:5:10 type E2 in sunken area.

Material and labour for Complete removal of existing roof treatment or roof tile, tarfelt, fungus, moss dust, plastr etc and removing from site to a place outside defence land as specified by civil authorities and clean the surface of roof with water and remove dust and Material and labour for highly elastic UV-resistant membrane one-component, water-based, liquid, and solvent-free coating for adhesion on various surfaces, including porous and non-porous substrates, with ability to bridge cracks ,cold applied, water-proofing membrane that is highly elastic and UV resistant. ASTM D 6083-97a Waterproofing and heat reflecting system having following key performance properties: 1.UV resistant, prevent yellowing and weathering 2.Highly elastic upto 350% and crack bridging 3.Excellent adhesion on porous and non-porous substrates 4. Tensile Strength >10 N/mm2 with GeoTextile fleece 5. Soler Reflective Index (SRI) more then 109-111 ASTM E1980-11 System: First coat:Providing and applying OEM prescribed compatible primer over the prepared surface for adhesion and bridging cracks. Coverage: 0.2kg/m2(with 50% dilution of water Reinforcement: Geotextile 40 gsm Second coat: highly elastic, UV-resistant membrane one-component, water-based, liquid, and solvent-free coating for adhesion on various surfaces, including porous and non-porous substrates,with ability to bridge cracks. Consumption: 0.5 kg/m2. Third coat: highly elastic, UV-resistant membrane one-component, water-based, liquid, and solvent-free coating for adhesion on various surfaces, including porous and non-porous substrates,with ability to bridge cracks. Consumption : 0.8 kg/m2. System buildup-1.5kg/sqm with geotextile of 40gsm

Demolition of Brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars,drains etc, but excluding ashlars facings, dressed stone work and precast concrete articles.

Material and labour for Brick work with sub class ‘B’ bricks straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified & as directed .

All as per item No 237 above but except bricks.

Material and labour for Brick work with sub class 'B' bricks straight or curved on plan to any radius in half brick thick wall in CM 1:4 complete all as specified & as directed .

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

Material and labour for Reinforced cement concrete, type B1, 1:2:4 mix (20mm graded aggregate) as in slabs & Shelves etc. complete all as specified and directed.

Formwork to soffits of slabs including supports, overhangings etc, for fair finished surfaces of concrete

Material and labour for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets/frames complete all as specified and directed.

Supply and fixing 5mm thick prelam hollow PVC wall pannel fixed on wall with tounge and grove joint including fixing with screw/fastner, adhsive, cover strip, corner strip complete all as specified as in stirrups

Providing & Fixing in position suspended false celling system using E Grid suspended celling Grid system. The size of Grid shall be 600X600mm with GI frame work, main runner 39X24mm, cross tee 29X24mm and wall angle 22.2X22.2mm using 4mm thick High Pressure Stream cured non primered classic/designer variant E-Board ISI Marked IS No 14862-2000. Fibre cement E Board to be placed in the gird of E Grid suspended ceiling grid system duly suspended by 4mm dia GI bar hangers from the pulins of the roof with butter fly clips.

Removing vegetation on roof /wall etc by taking down/dismentling/ demolation of brick work/ concrete work/ plaster work etc from root and apply chemical on the vegetation for further non growth in future and making good surface with concrete, tile, roof treatment platers etc complete to make good surface with existing complete all as specified and directed. (Including all necessary scaffolding lifiting arrangement up to 10 mtr height).

(Summer/Winter appliances)

Labour for repair/servicing of ceiling fan of any capacity complete with strip opening of ceilling fan for repair/cleaning/varnishing and removing of old lubricating substances from bearing/ bush by using Kerosine oil, carrying out fresh lubrication , greasing and to make the ceiling Fan noise free and smooth functioning, including replacement of worn out/unserviceable minor spare parts split pin,fan body bolts,spring washer,fan rod bolt etc and PVC insulated, unsheathed stranded twin twisted copper conductor cable of size 1.5 Sqmm up to 1.0 M long, assembling the repaired ceiling fan and testing to the entire satisfication of engineer in charge and refifixing in its orginal position all as specified and directed. (Replacement of Spares flexible wire etc/rewinding of ceiling fan/shall be measured and paid seperately under respective item for material and labour cost .)

All as per Srl item No. 250 above but for exhaust Fan of any type and any sweep

Rewinding of ceiling fan, of any make/type and size (1200 sweep) with super enamelled copper wire of appropriate gauge as existing to obtain the specified and satisfactory RPM as per manufactures specification, including replacement of all insulation materials, varnishing, heating, drying, assembling of stater/rotor, connection & testing complete.

All as per Srl item No. 252 above but for exhaust fan of any make/type but of size 300 mm sweep.

Labour for remetalling of worn out shaft of fan, cutting,bracing,machining and polishing to make the shaft suitable for fixing of new ball bearing and fixing ball bearing in repair of bushing system in ceiling fan and assembling the same and testing to the engineer satifaction of engineer in charge to ensure smooth and noise free operation (bearing shall be measured and paid seperately )

Supply and fixing in replacement ball bearing of any size and type, suitable for ceiling Fan .

All asper item No. 255 above but for exhaust fan of any type/make and size

Supply & fixing in repair of capacitor 230 Volt AC 50 Hz, conforming to IS-1709 and Rated capacity 2.5 MFD for ceilling fan & exhaust fan.

All as per item No. 257 above but of rated capacity 4.0 MFD for Exhaust Fan.

Supply and connection of PVC insulated, unsheathed multi stranded,three core twisted copper flexible cable of size 1.5 Sqmm as required. .

Supply and fixing in replacement bush of suitable size for ceiling fan/exhaust fan of any type/size as per existing type.

Supply and fixing in replacement of PVC connector 4 way 6 Amps with connection screws, nuts.

Supply and fixing in replacement of PVC clamps with fixing screws for holding capacitor of any type and size.

Supply and fixing in replacement of GI/ MS anodized bolts with anodized nuts, spring washers, split pin etc size 50 mm long 10 mm dia half threaded type with split pin hole

Supply and fixing in repair MS clamp for down rod of suitable size including gromet / reel type rubber pad with bolts, nuts,split pin and washers suitable for housing ceiling fan.

Supply and fixing in repair of ceilling fan down rod 12 mm dia and 30/45 cm long complete with MS Clamp Rubber reel,split pin nut bolts etc.

Supply and fixing in replacement Printed circuit board (PCBs) suitable for BLDC ceiling fans of 1200 mm. Make - As per sample .

Supply and fixing in repair of louver shutter made out of MS sheet metal 1.2 mm thick for round base and 0.8 mm thick for flaps, comprising of mounting legs frames made o MS flat strips of size 25mm x 3mm includidng heavy duty rust proof passivated bolts of size 50 mm long 8 mm dia to be fixed on wall at ground/First/Second floor etc complete with using fastener bolt,driling for exhust fan up to 400 mm sweep incl taking down old one.

Cleaning of ceiling fan assembly of any type/size and carrying out two coat of spray painting with first quality synthetic enamelled paint of approved colour all as directed and specified.

Supply and fixing in repair PVC Canopy set of two pieces for ceiling fans of any size

Supply and fixing in repair Ceiling Fan blade set of three pieces suitable for 1200/1400 mm sweep of White/Brown/Ivory colors all as specified and directed. Make - As per Sample

Taking down and strip opening to geyser of any make and capacity 25 / 35 / 50 ltrs including disconnection of all water pipe connection and taking out water inlet / outlet assembly, removing glass wool, the inner tank, descaling the assembly and tank, detecting the leakage, welding / brazing the defective parts, repacking the glass wool and refixing the same after making it functional including replacement of worn out nuts, bolts, washers etc complete all as specified and as directed.

Material and labour in repair of water inlet and outlet geyser assembly of existing make as required at site with rubber gasket suitable for geyser of 25 / 35 ltrs capacity electric driven water storage heater with provision of housing for thermostat assembly, heating element fixing arrangement nuts, bolts and washers etc complete all as specified and as directed.

Material and labour in repair thermostat, switch for electric water heater storage type of capacity 25 / 50 ltr, 230 Volts of existing make of geyser complete all as specified and as directed.

Material and labour in repair heating element with triangular base / round base, single phase, 230 Volt, capacity 2 KW of existing make complete all as specified and as directed.

Material and labour in repair pressure release valve conforming to relevant IS 15mm bore suitable for fixing with GI pipe / tubing 15mm bore complete all as specified and as directed.

Material and labour in repair of heavy duty PVC connection (For Hot water) nylon threaded 450mm large (18") 15mm bore including brass nuts, rubber washers complete on both ends complete all as specified and as directed.

Material and labour in repair of heavy duty PVC connection (For Cold water) nylon threaded 450mm large (18") 15mm bore including brass nuts, rubber washers complete on both ends complete all as specified and as directed.

Material and labour in repair of indicator lamps round / rectangular type 230 Volt AC suitable for geyser of any capacity including providing electric connections complete all as specified and as directed.

Material and labour in repair water storage inner tank of stainless steel heavy duty confirming to ISI suitable for 25 ltrs capacity geyser, with provision for fixing 15mm dia galvanized air release valve complete all as specified and as directed.

Material and labour in repair Non return Valve 15mm dia,made up of brass complete all as specified and as directed.

Material and labour for repair/Maint to desert coolers complete with and including cleaning,scrapping/ rubbing old rusted surface ,filling cavities and painting with two coat of high quality aluminium paint over a coat of red oxide primer externaly and black paint internally with synthetic enamelled paints complete with replacement of necessary nut,bolts,rubber pads for fan motors and writing MES No/unit name all as specified and directed by the Engr-in-Charge.

Supply and fixing in repair of desert cooler fan motor 90 watt,1400 RPM,230 volt 50 Hz single phase conforming to ISI complete with fan blade and capacitor of sutitable size.

Supply and fixing in repair of Desert Cooler submersible pumping set single phase 230 volt , 50 Hz of 0.25 to 1.0 HP conforming to ISI complete with lead.

Supply and fixing in repair of desert cooler fan motor blade of existing size made out from MS having duty complete with key bolt.

Supply and fixing in repair of unsv Khas Khas/Grass pad for desert cooler Set of three peices complete all as specified.

Repair/Maint/Servicing to refrigerator/deep freezer/water coolers/AC's of any capacity and model by replacing capillary tubing,gas chargings,rectification of leakage in capillary tubing/Chiller plant/water tanks,condensing coils,repair to wiring,flushing/cleaning condensing/cooling coils/internal/External unit of split AC,greasing to blower motors,replacement of spare parts, fan belts and make refrigerator/deep freezer/water coolers/AC's in serviceable condition all as specified and directed by Engr-in-Charge. Note:Spare/Gas charging paid seperatly.

Supply only sealed compressor unit seamless welding company manufacturer with filling of refrigerent gas conforming to ISI as under:-

For refrigerator 175/285 Ltr capacity

For Deep Freezer 200 Ltr capacity

For Water Cooler 40/80 Ltr capacity

Split/Window AC 1.5 Ton Capacity

Supply only condensing fan motor 1/5 HP 1440 rpm Single phase 230 Volt 50 HZ with double blade and shaft end with fan belts for windows AC/Split AC conforming to ISI of capacity 1.5/2.0 ton complete with vibration parts etc.

Supply and charging refrigerant 134A/412A in sealed compressor unit of refrigerator/deep freezer/water coolers/AC's of any type and capacity after flushing the complete system with carbon tetrachloride (CTC) and vacuumise the complete system with vacuum pump and testing on full load including replacement of filter,strainer all as specified and directed.

Supply and fixing in repair of following spare parts for refrigerator/deep freezer/water coolers/AC's of any capacity:

Starting relay

Overload protector

Thermostat switch

Defroz switch

Supply and fixing in repair of following unsv spare parts of water cooler of any capacity

Starting capacitor 45 mfd

Running capacitor 60/120 mfd

Push cock chromium plated 15 mm with nipple 6'' long

Supply and fixing in repair of copper cable PVC insulated and sheathed of size 1.0 sqmm 3 core FRLS 230 volt,50 Hz conforming to ISI all as specified and directed.

Supply and fixing in repair of copper cable PVC insulated and sheathed of size 1.5 sqmm 3 core FRLS 230 volt,50 Hz conforming to ISI all as specified and directed.

Supply and fixing in repair of copper cable PVC insulated and sheathed of size 2.5 sqmm 3 core FRLS 230 volt,50 Hz conforming to ISI all as specified and directed.

Material and labour for fasteners 80 -100mm long for fixing of geyser of capacity upto 50 ltrs including grouting completed works in wall as per site requirement with the floor complete all as specified and as directed.

(Internal electrification)

Material and labour in repairs for Sub main wiring with proper colour coding , insulated , unsheathed , multistranded ,copper conductor FRLS, cable of 2 run 6 Sqrmm for phase and neutral and one run of 6.0 Sqrmm for earth wire unsheathed , miltistranded , copper conductor FRLS, drawn through the existing rigid PVC concealed conduit fixed on wall. Two runs of cable for phase/neutral and one run of cable for earth will be measured and paid as one unit length. Note : Wiring shall be done in proper colour coding.

Material and labour in repairs for Sub main wiring with proper colour coding , insulated , unsheathed , multistranded ,copper conductor FRLS, cable of 2 run 4 Sqrmm for phase and neutral and one run of 4 Sqrmm for earth wire unsheathed , miltistranded , copper conductor FRLS, drawn through the existing rigid PVC concealed conduit fixed on wall. Two runs of cable for phase/neutral and one run of cable for earth will be measured and paid as one unit length. Note : Wiring shall be done in proper colour coding.

Taking down old unsv copper/aluminium point wiring concealed / batten (light, fan, socket or power) complete, including fixture and fittings such as switches,sockets, ceiling roses,bell push,bell electric,lamp holder,bulk head fitting, pendants, regulators, sockets, light fitting and any type switch board wooden/iron,round block etc removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc

Material and labour for point wiring for one light/fan/call bell point controlled by one 5 Amp switch with 1.5 Sqmm single core multistranded copper conductor FRLS, PVC insulated (unsheathed) heavy duty cable including continuous earth wire of size 1.5 sqmm copper conductor multistrand FRLS, PVC insulated (unsheathed) drawn into and including new concealed PVC rigid/ 1.8mm wall thickness ISI marked including new CI/pressed steel terminal boxes including 3.00mm thick hylam brand IS-2036 marked, laminated sheet cover for mounting switches, sockets, fan regulators etc complete all as specified. Note : (a) wiring shall be done by using proper colour coding including making the disturb surface good (b) Earth wire shall be of green colour (c) On RCC roof/celing PVC conduit shall be provided on surface with proper fixing clamps all as directed by Engr-in-Charge.

All as per item No 312 here in above but 5 Amp socket outlet on same board

All as per item No 312 here in above but socket outlet 5 Amps independent board complete all as directed by Engr-in-Charge.

All as per Item No 312 here in above but for one 6 pin socket outlet 15 Amps on Independent board with cables 2.5 sqmm size

All as per item No 312 above but for One bell/buzzer point controlled by one push button on the same board with other switches or independent with cable 1.5 Sq. mm size

Material and labour for point wiring for one light/fan/call bell point controlled by one 5 Amp switch with 1.5 Sqmm single core multistranded copper conductor FRLS, PVC insulated (unsheathed) heavy duty cable including continuous earth wire of size 1.5 sqmm copper conductor multistrand FRLS, PVC insulated (unsheathed) drawn into existing concealed PVC rigid/steel conduit and into existing CI/pressed steel terminal boxes including 3.00mm thick hylam brand IS-2036 marked, laminated sheet cover for mounting switches, sockets, fan regulators etc complete all as specified. Note : (a) wiring shall be done by using proper colour coding incl making the disturb surface good. (b) Earth wire shall be of green colour (c) On RCC roof/celing PVC conduit shall be provided on surface with proper fixing clamps all as directed by Engr-in-Charge.

All as per item No 317 here in above but One 5 pin socket outlet 5 amps on the same board

All as per item No 317 here in above but One 5 pin socket outlet, 5amps, independent

All as per Item No 317 here in above but for one 5 pin socket outlet 15 Amps on Independent board with cables 2.5 sqmm size.

All as per item No 317 above but for One bell/buzzer point controlled by one push button on the same board with other switches or independent with cable 1.5 Sq. mm size

Supply & fixing switch piano, flush type single pole one way 5Amp, 240 volts ISI marked complete all as specified and directed .

Supply & fixing Socket outlet 2 in 1, 3 pin, 5A complete all as specified and directed .

Supply & fixing Switch socket outlet combined 2 in 1 , 3 pin 5 amp and 15 amp flush type , 240 volts ISI marked complete all as specified and directed.

Supply & fix calling bell ding dong/buzzer ,AC 230Volts single pole complete all as specified and directed.

Supply & fix stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. complete all as specified and directed.

S & F for bell push , flush type single pole , 5Amp, 240 volts all as specified .

Supply and fixing Ceiling Rose 3 terminal surface type Complete all as directed.

Supply and fixing for Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings

Supply and fixing Self ballast LED retrofit Lamp with PVC body and PC Diffuser 9 watt 230 Volt 6500K Complete all as directed.

Material and labour for point wiring for one light/fan/call bell point controlled by one 5 Amp switch with 1.5 Sqmm single core multistranded copper conductor FRLS, PVC insulated (unsheathed) heavy duty cable including continuous earth wire of size 1.5 sqmm copper conductor multistrand FRLS, PVC insulated (unsheathed) drawn into and including new concealed PVC rigid/ 1.8mm wall thickness ISI marked including Modular Metal flush Boxes of any way i.e. (1 to 8 way as per site requirement) for mounting switches, sockets, fan regulators etc complete all as specified and as directed for the following :- Note: suitable Modular white cover sheets with frame as specified to be provided in replacement to MS/Galvanised sunken boxes and measured & paid separately as per relevant item. Note : (a) wiring shall be done by using proper colour coding including making disturb surface good (b) Earth wire shall be of green colour (c) On RCC roof/celing PVC conduit shall be provided on surface with proper fixing clamps all as directed by Engr-in-Charge.

All as per item No 331 here in above but 5 Amp socket outlet on same board

All as per item No 331 here in above but socket outlet 5 Amps independent board complete all as directed by Engr-in-Charge.

All as per Item No 331 here in above but for one 6 pin socket outlet 15 Amps on Independent board with cables 2.5 sqmm size.

All as per item No 331 above but for One bell/buzzer point controlled by one push button on the same board with other switches or independent with cable 1.5 Sq. mm size

Supply and fixing Modular switch 1 way 6A,1 module , 240 volts ISI marked complete all as specified and directed

Supply and fixing Modular switch 1 way 16A, 1 module , 240 volts ISI marked complete all as specified and directed

Supply and fixing Modular Socket, 6A - 2/3 pin combined 2 module, , 240 volts ISI marked complete all as specified and directed

Supply and fixing Modular Socket 6A/16A - 2/3 pin combined 2 module, , 240 volts ISI marked complete all as specified and directed

Supply and fixing Modular Fan step regulator, 120W 1 module , 240 volts ISI marked complete all as specified and directed

Supply and fixing Modular bell push 6A 1 module complete all as specified and directed.

Supply and fixing bulk head luminaries IP65 with opal diffuser 10 watt, 230 Volts LED type complete with 10 watt LED Bulb all as directed Engr-in-Charge.

Supply and fixing LED lights fitting 1x 20W, 220V, Batten type complete with LED tube rod 20 watts driver, holder and power factor >0.95 , SPD 2.5 KV, 100 Lumen/Watt, 6500 K cool day type conforming to ISI including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete. (4' ft long ) with LED rod 20 watt, 230 Volts 50 Hz.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete.

Supply and fixing in repair LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders and LED lamp suitable for roof, ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and as directed.

Please Enable Macros to View BoQ information