WBPHED/EE/07_08/BOLMD/25-26

Amount

Submersible pumping machinery directly coupled with water proof suitable size motor having following specification :- Pump:Duty condition -28m3/Hr Head- 60 Mtr Shaft-stainless steel Impeller- S.S / GM Outlet Size: 65mm / 80mm. Motor:Submersible type 3 Ph , 50Hz, 415 Volt ± 10% 2900 RPM Motor must be suitable for operation with star delta starter.(Test certificate along with characteristic curve should be submitted at the time of delivery).

Supply,delivery at site and storage of 2mm thick CRCA sheet steel enclosed cubical type Outdoor type floor mounted 415v Kiosk power distribution Board Cum Motor Control Center having Required front door locking Arrangement,feeders,starters etc. as per Specifications as follows: 63 Amp/36KA MCCB with E/F relay MCCB adjustable Olr With Thermo Magnetic release for O/C,S/C,E/F,Auto phase corrector & SPD protection OUTGOING With all protection:(a) 7.5HP to 12.5 HP SDS Feeder (Low lift)-2 nos (1W+1 Spares) with digital timer for auto start -stop and suitable capacitor bank for improvement of power factor,all protection & relay (B) 32AMP/25KA TPN MCCB feeder with timer(outdoor lighting)- 1 no,(C) 63 AMP/25KA 4P MCCB(spare)-1 no Each individual feerder should consist of indicator lamp(LED),proper rating voltmeter & Ammeter.All the components(major)-Siemens/ABB/Approved make of PHED

Supply Delivery And installation Of Suitable CRCA enclosure powder Coated Minimum 2mm IP55 protection And suitable for outdoor installation,the Enclosure should have Sufficient space for installation of WBSEDCL energy meter As well As Provision for smooth meter Reading Periodically(Size:3'x1'x5')

Making CC foundation for Support Of the Kiosk box After excavating the earth upto a Depth of0.6 Mtr below the GL including Supply of All materials Complete with 12 mm thick cement Plastering With Net Cement Finishing Complete As per Direction Of EIC

Supply delivery and Installation of 63 Amp main Switch at the suitable position of the kiosk Box For Receiving The Power

Making wire net fencing of the pump platform by supplying and fitting fixing of Galvanished MS Angle of approved quality which will be grounted in the earth by cement concrete as per direction of EIC including an arrangement for a gate with lock and key facility as per Direction Of EIC

Supply,delivery at site And storage of 3 Core 4 Sq.mm water proof Flat submersible cable9 Make:Finoex/Havels/Polycab/approved make)

1.1KV grade 16 sq.mm 3.5 core XPLE Aluminium armoured Cable.

Supply,delivery and Storage of following valves,pipes and gadgets etc. at Site:(a) 80 mm Dia UPVC standards type coloumn pipe(cream Colour with both side threaded and one end side socket with register KPMG),Make : Ashirbad/Approve make of PHED

3 Mtr Long

1.5 mtr Long

80 Mm dia Ci top and bottom adapter

Heavy type 250mm dia./suitable Split type tube well cover with clamping arrangement including supply of nuts, bolts and washer as per departmental design.

Heavy type suitable dia. MS suspension clamp along with nuts bolts and washers.

80mm dia Non-Rising Spindle Suice valve9PN_1.0 rating) as perIS14846 for washout line,make:IVI/jupiter/Cair/approved make of PHED.Moc & TC Needed for valve

80 mm N.R.V(PN-1.0 rating) as per IS5312,Make:IVI/jupiter/Cair/approved make of PHED.Moc & TC Needed for valve

Anti snapping safety device for pump set by supplying suitable size of MS angle busket and nylon rope of required length including supplying of nuts, bolts and all other materials.

150 mm dial Pressure gauge [Range 0-7kg/cm²] with glycerine filling inside the dial including brass cock and fitting complete [This cost includes 15mm. dia G.I. pipes and specials].

Making brick pillar 0.25x0.25x0.75 Mtr/suitable Height for supporting of valves and pipes with 12mm thick plaster and net cement finish complete.

Installation of Submersible Pumping machinery to newly sunk tubewells along with Coloumn pipe(as required),top cover,valves,Apecial of above protection pipe And supply of MS clamp,nut bolt,cable gland,sockets etc, making inter connection of the pump delivery line to pump collecting main line near tubewell with supply of all neccesary pipe,reducer/enlarger,GI/MS specials etc. including brick,sand,cement,rod Etc. and laying & drawing of all cable &cable protection pie as equired and all to complete the job including all connection & testing commisioninfg as per Direction of EIC

Installation of above mentioned MCC panel by skilled Technical Person under Supervision & Guidance of manufacturer at their respective places by all the Neccesary material &equipments,after dismanting the old defective panel(if Any) and mending damages good of floor<drawing power cable with suitable size by proper wiring and fitting suitable place within the pump house with all neccesary connection as per direction of EIC with testing and commisioning complete,

Painting of installation(Viz, pumps,valves,pipe lines etc. by two coat epoxy paint(colour to be declare by EIC) over a coat of primer as per NIT specification and direction of EIC.

Supply and delivery at site of GI octagonal street light pole conical type 7 Mtr length(Top dia 70 mm,bottom dia 130 mm,thick 3 mm base plate 220x220x12mm,foundation bolt M20x700 with template and anchor plate,bracket Single Arm1500 mm long on single side with 48.3 OD GI pipe& internal junction box(6a,SP MCB & 4-way connector) resin Coated MAke Approved make approved make

Erection of Grp pole of length 7 Mtr in RCC Foundation of 400x400 mm Of depth of 1300 mm below the GL and 200 mm just above the GL. 4 Nos "J' type foundation bolt of 20 mm dia and 600mm long grounted into RCC foundation ,,There should be provision of 2 no of flexible pvc pipe of 63mm diafor cable entry as per supplied drawing and departmental drawing and design

supply and delivery at site of energy efficient LED Smart Bright street light fixture with IP66 and IK06 protected LM high pr. Aluminium di cast housing with polycarbonate cover capable of delivery Standard lumen output as follows.The lens plate should be bolted with metal core PCB sholud not be glued<the driving current should be more than 700 mA.it should have internal surge protection of minimum 4kv,Lumen/watt>100,driver efficiency >85%,PF>0.985,THD<10% Philips BRP409 LED074 CW HE MR FG S1 PSU GR SPD

Fitting fixing of above supplied Led light fitting complete with all accessories to vbe fixed with S&F length of 1.5sqmm PVC insulated single core stranded annealed copper wire and making connections as required complete

Earthing with 1 no of G.I earth spike(20mm dia X 1.5 mtr. Long) driven into the ground upto 2 mtr. Drawing earth ine with separate 6 SWG G.I Wires providing 15 mm dia. G.I pipe protection from earth spike feeder box/junction box/poles and fixing to the same suitable nuts 7 bolts all complete asper direction of EIC

Making earthing arrangement as per following --

Excavation of soil for installation of Earth electrode and filling and ramming for soft soil.

Earthing with 50 mm dia Gl pipe 3.64 mm thick x 3.04 Mts.long with TATA-Medium GI pipe with a provision to connect 25mm X 6mm GI flat strip complete with GI bolts, nuts, washers etc as required.

Connecting the equipments body to earth busbar including S&F 20mm X 3mm galvanized (Hot dip) MS flat on wall/floor with GI saddles as required and connection of equipments incld. drilling holes, with bolts, nuts, washers etc as required.

Extra for providing masonery enclosure on the top of the earth electrode of overall size 86.36cm X 86.36cm X 46cm deep (below ground level) complete with cemented brick work (1:6) of 25cm width duly plaster with cement morter (inside) CI hinged inspection cover of size 36.56cm X 35.56cm with locking arrangement, GI reducer including drilling of 46nos. 12mm dia holes on the GI pipe.

Extra treatment of soil by using salt and charcoal or coke for plate electrode.

Commisiong of the whole installation and testing by Licenced Electrician after drawing of power cable,fixing of Main switch as per instruction of EIC [N.B: (1) Pump data is to be confirmed with the yeild test report of the tube well. (2) Third party inspection of the work is mandatory as per guidelines of NJJM and direction of EIC without any extra cost. (3) Drawing, design and make of the materials are to be approved from the EIC before procurement.]

Add: GST @ 18% on sum of Item No: 1.00 to 26.00

Add: Cess @1% on sum of Item No. 1.00 to 27.00

Jal Pravahika Pvt. Ltd. (BID ID -6444215)

CHATTERJEE ENTERPRISE (BID ID -6449244)