Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹67.5 LAccepted-AOC FLAT NO B 401 4TH FLOOR NAVADURGA CO OP HSG SOCIETY LTD PLOT NO 7 SECTOR 19A NERUR EAST NAVI MUMBAI THANE MAHARASHTRA 400 706 | NAVI MUMBAI | THANE | MAHARASHTRA | 400706 | L1 | Accepted-AOC Being Lowest | |
| 2 | L2₹75.3 L+₹4.9 L (6.99%)Rejected-Finance SHOP NO 10 BMC SHOPPING CENTRE MITHA NAGAR GOREGAON WEST MUMBAI 400 104 | MUMBAI | MUMBAI SUBURBAN | MAHARASHTRA | 400104 | L2 | Rejected-Finance Other than being lowest | |
| 3 | L3₹84.7 L+₹14.3 L (20.3%)Rejected-Finance FLAT NO 002 MAHAVIR VILLA CHS LTD PLOT NO 259 SECTOR 21 NERUL EAST NAVI MUMBAI 400 706 | NAVI MUMBAI | THANE | MAHARASHTRA | 400706 | L3 | Rejected-Finance Other than being lowest | |
| 4 | L4₹1.1 Cr+₹38.7 L (55.0%)Rejected-Finance GARDEN AVENUE PLOT NO 242 243 244 RH 4 SECTOR 21 NERUL NAVI MUMBAI 400 706 | THANE | MAHARASHTRA | 400706 | L4 | Rejected-Finance Other than being lowest | |
| 5 | Rejected-Technical | - | Rejected-Technical Two class below |
Tender Value
Refer Docs
EMD Value
₹2.0 L
Closing Date
17 Nov 2022, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
CWE (NW) Mumbai
Commander Works Engineer NW Dr Homi Bhabha Road Navy Nagar Colaba Mumbai 05
STRUCTURAL REPAIR TO VARIOUS CAISSONS AT SBW JETTY AT ND MBI UNDER GE NW KUNJALI COLABA MUMBAI
2022_MES_557528_1
8513/CWE (NW) Mumbai/ E8
Open Tender
Civil Works
Item Rate
180 days
GE (NW) KUNJALI
Class B
7 documents required · 7 mandatory
₹1,000
Yes
GE (NW) Kunjali
₹2.0 L
Yes
27 Dec 2022
13 Oct 2022
19 Nov 2022
13 Oct 2022
17 Nov 2022
3 Nov 2022
13 Oct 2022 - 1 Nov 2022
Amount
Demolition of plain cement concrete of any description and in any position not other wise specifically provided for complete all as specified and directed by Engineer-in-Charge.
Material and labour for ready mix cement concrete in Pavement/Hard standing (PQC) M-40 of flexural strength of 40Kg/Square cm in field using minimum 500 Kg of cement per cubic metre laid in bays or as directed with and including steel formwork to sides of concrete spread, compacted and finished in a continuous operation etc complete all as specified and directed by Engineer-in-Charge.
Material and Labour PCC (1:2:4) type B-1 (Using 20mm graded stone aggregate) as in roof/chajja padding for maintaining roof/chajja slope complete all as specified and directed by Engineer-in-Charge.
Demolition of reinforced cement concrete of any description and in any position not other wise specifically provided for complete all as specified and directed by Engineer-in-Charge.
Material and labour precast RCC (1:2:4) type B1 using 20mm graded crushed stone aggregate as in cover slabs and set incement mortar 1:4, complete all as specified. (Reinforcement shall be measured complete all as specified and directed by Engineer-in-Charge.
Material and Labour PCC 1:2:4 type B-0 (using 12.50 mm graded aggregate) cement concrete as a leveling course on roof surfaces and coping complete all as specified and directed by Engineer-in-Charge.
Material & labour for taking down, chipping and removing the loose, spailt, damaged cement concrete, cement mortor surfaces of RCC columns, beams, walls, chajjah etc and exposing the reinforced cement , wire brushing and cleaning the exposed steel reinforced bar, applying rust remover over the cleaned re-bar surface wash the re-bar with clean water for removing all rusts from the old re-bar surfaces, fixing new reinforcement for strengthening the members as required, applying two coats of epoxy zinc primer on new and old steel surfaces, saturate the substrate with water applying one coat of polymer modified bond coat on affected concrete surfaces and finally providing 40mm thick polymer plaster (1:5:15, cement, sand, polymer) and finally finishing the surface complete all as specified and directed by Engineer-in-Charge. Make :- Dr.Fixit/Sunanda/Chemestik/Fosrok as approved by GE. Note :- (New reinforcement and MS Sections will be measured and paid separately)
Material & labour for taking down, chipping and removing the loose, spailt, damaged cement concrete, cement mortor surfaces of RCC columns, beams, walls, chajjah etc and exposing the reinforced cement , wire brushing and cleaning the exposed steel reinforced bar, applying rust remover over the cleaned re-bar surface wash the re-bar with clean water for removing all rusts from the old re-bar surfaces, fixing new reinforcement for strengthening the members as required, applying two coats of epoxy zinc primer on new and old steel surfaces, saturate the substrate with water applying one coat of polymer modified bond coat on affected concrete surfaces and finally covering with Microconcrete and finally finishing the surface complete all as specified and directed by Engineer-in-Charge. Make :- Dr. Fixit/Sunanda/Chemestik/Fosrok as approved by GE. Note :- (New reinforcement and MS Sections, microconcrete and form work if required will be measured and paid separately)
Supply only ready mix microconcrete mixture. complete all as specified and directed by Engineer-in-Charge.
Supply and Fixing welded steel wire fabric, cut to length, fixed to steel members/reinforcement steel, weight per Sqm nexc. 4 Kg complete all as specified and directed by Engineer-in-Charge..
Replacement of steel reinforcement with TMT bars of appropriate size where 30% of cross section is reduced including dismantling of rusted steel complete all as specified and directed by Engineer-in-Charge.
Providing and fixing additional main steel bar or stirrups of designed diameter in various structural elements like column, beams and foundations including drilling, bending and fixing the bars with epoxy putty etc complete all as specified and directed by Engineer-in-Charge. (Steel provided on the basis of 1% of volume of concrete)
Dismantling wrought or mild steel work of any description complete all as specified and directed by Engineer-in-Charge.
Material and Labour for Stainless steel decorative railings (grade 316), staircase3 (design and pattern as approved made out of SS pipes, SS flats, SS plates etc. Complete with and including necessary welding , buffing/polishing and fixing complete all as specified and directed by Engineer-in-Charge.
Material and Labour for Stainless steel decorative railings chain alloy(grade 316), having 8 mm minimum thickness (design and pattern as approved ) as used to connect two stainless steel post with hooks etc. Complete with and including necessary welding , buffing /polishing and fixing complete all as specified and directed by Engineer-in-Charge.
Material and Labour for epoxy base joint filler paint on external surfaces of walls/floor to fill the cracks with and including resin and hardner in proportion as per manufacturers instructions complete all as specified and directed by Engineer-in-Charge.
Material and Labour for drilling and fixing Rohibb teflon nozzles in RCC members, including drilling holes of 12 mm dia, 50 to 100mm deepholes. Works shall be carried out as under : - (i) Cleaning holes. Clean the holes by air blower prior to fixing nozzles. (ii) Fixing of nozzles. Insert 12 mm dia. Rohibb Teflon nozzles in cleaned holes. External end of nozzles to be made to receive outlet of grouting gun. Fix it inside the holes by applying thixotropic epoxy putty to ensure complete sealing. Cure the system for min 12 hr. (iii) Cutting of nozzles. Cut the nozzles by chisel after completion of grouting without damaging structural elements. (iv) In case crack upto 2mm wide, fix the injection nozzels directly over the cracks, at intervals of 6 to 9 inches, using a drilling machine. Fix PVC/MS nozzels in these holes with fast-setting epoxy putty & let it dray for 2 to 3 days. Also seal the crack between the ports with epoxy putty. (v) In case crack is wider 2mm upto 4 mm to 5 mm wide drill holes at the sides of crack in a staggered manner , at intervals of 6 inches and affix them epoxy as mentioned above. (vi) Also, sealing the face of the crack with a liberal application of the epoxy putty and including scaffolding upto any height.
Material and Labour for injecting of site mixed cement slurrry grout, mixed in specified proportion containining cement ,sand, water with addition of plasticizers (approved make) & migratory corrosion inhibitor, water cement ratio shall be varied between 0.5 to 1.0 for each hole, shhrinkage compen satingenslurry mixed to a lump free fresh creamy consistency, mixing shall be done by mixer continuouly stirring mechanically to keep cement particles in suspension. Injection of approved/specified grout by means of pump at a pressure of 3-5 Kg/cm2 etc complete till the grout mix flows out from the nozzle indicating and including scaffolding upto any height complete filling of grout in the holes drilled complete all as specified and directed by Engineer-in-Charge. Make/brand of epoxy grout- Dr Fixit Epoxy injection of Eppco KP-HP-250 of m/s Krishna conchem or shaligrout EIi of STP Ltd or as approved by GE.
Material and Labour for injecting Low visosity (3-5cps) high molecular weight monomer by pressure and using mechanized injector gun with accessories till nozzles refuses to accept the grout, including, mixing or material as mixing of material components (Part a&b) in the required quantities as per manufacturer's instruction by weight batching. Grouting fill the grouting gun with concrete penetrating corrosion inhibitor EPCO-KP-100/protectsil CIT or Ferogard 903. Maintain desired pressure in the gun by air compressor ; maintain the pressure at exit (2 to 3kg/Cm2) by monitoring pressure guage at exit grout the material throught prefixed nozzles in the structural elements @ 100ml per nozzle. Repeat the process for all the nozzles and including scaffolding upto any height complete all as specified and directed by Engineer-in-Charge.
Complete removal of existing wate proofing treatment upto concrete surface including cleaning, wire brushing, watering, removal of debris upto 15 Km distance complete all as specified and directed by Engineer-in-Charge.
Material and Labour for applying a coat of bituminous primer conforming to IS-3384 @ 1.20 Kg/Sqm on prepared surface of plaster as per manufacturer's instructions, manufactured by the same agency of APP membrane. Providing and laying five layered 4 mm thick APP (Atatic poly propylene) modified polyester reinforced water proofing membrane with minimum weight of 4.60 Kg/Sqm as specified here-in-after. The APP membrane shall be laid using LPG torch-on-application with minimum 100 mm side overlap and 150 mm end overlap. The laying of membrane shall be got done through an authorized applicator of manufacturer of the membrane. The APP membrane shall be taken upto minimum 200 mm on vertical surfaces. The edge of the membrane shall be sealed with sealant. The rain water gutter portion shall be finished with cement mortar 1:4 to provide requisite slop towards rain water pipe outlet complete all as specified and directed by Engineer-in-Charge. Notes :- (i) Irrespective of lap the net covered area shall only be measured and paid (ii) The quoted rate shall be deemed to be inclusive of primer for APP membrane and SBR latex complete.
Taking down cement plaster on brick surfaces built in cement mortar including raking out joints, bedding for key scrubbing down with water etc complete all as specified and directed by Engineer-in-Charge.
Material and labour rendering 15mm thick on brick work or concrete surfaces in cement mortar 1:4 finished even and fair including mixing integral water proofing compound in the proportion as mentioned in manufacturer's instructions complete all as specified and directed by Engineer-in-Charge. (Water proofing compound to be measured and paid for separately).
Material & labour for rendering minimum 20mm thick polymer modified mortar in cemet mortar (1:3) with graded quartz sand with additive Monolith - PMM of Fosroc/Krishnaconchem or polymer mortar HB of Dr. Fixit or Shalifix RM SG 01 of STP Ltd. 15% by weight of cement in one coat with and including curing as per manufacturer's instruction complete all as specified and directed by Engineer-in-Charge.
Supply and applying microconcrete of Fosroc, Dr Fixit, or equivalent aroung edges of Dock walls, jetties, corners, grooves, alters, steps, piers and other marine structure after complete cleaning of concrete surface and applying epoxy coat as bonding agent Fosroc's Nitobond or equavalent for bonding between old and new surface, including all lifts, shuttering all as required as per site condition and directed by Engineer-in-Charge.
Supply only Integral waterproofing compound complete all as specified and directed by Engineer-in-Charge.
Material & labour for cleaning the surface of the stone/concrete in jetty , dock,retaining wall, piers of jetty and bottom portion of deck slab etc above sea with mechanical grinder and specialized water misting techniques applying water jet using a fine nozzle sprinkling system calibrated to spray a fine mist along the stone/concrete surface complete and removing all sea vegetation complete all as specified and directed by Engineer-in-Charge. Note:- Quoted rate shall be inclusive of scaffolding or alternative way of carrying out the work with proper safety instruction required at site.
Material and labour for applying two coats of anti carbonation paint DEKGUARD S of FOSROC or equivalent over a coat of primer DEKGUARD of FOSROC or equivalent over vertical concrete surface in jetty/dry dock above sea level all as specified and directed by Engineer in charge. Note:- Quoted rate shall be inclusive of scaffolding or alternative way of carrying out the work with proper safety instruction required at site.
Material and labour formwork to sides and soffits of floor or roof beams, haunchings, girders, bressummers, lintels cantilevers, shelves including supports, overhangs, etc. Also splays between floors and beams, etc. rough finished surface of concrete complete all as specified and directed by Engineer-in-Charge.
Material and labour formwork to sides of pillars posts, struts, piers, columns and stanchions square, rectanguar or polygonal complete all as specified and directed by Engineer-in-Charge.
Material and Labour for errection & dismantling of MS tubler double scaffolding (H frame) upto height of 30m & with necessary brazing, provision of necessary safety equipment to the skilled workers to carry out the work and covering with green cloths for carring out external face work of walls complete all as specified and directed by Engineer-in-Charge.
Supply and fix rolled mild steel section of Grade FE 410-W, (Gde- E-250) quality-A, as in Plates (Plane or Chequered) channels, square cut or noteched (ordinary and counter sunk) forming holes, without any attachment complete all as specified and directed by Engineer-in-Charge.
Supply and fix structural steel framed works such as angle, channel, grating, gate, ladder etc. Confirming to Fe-290, E-165 as in supporting structure of duct, drain edge etc including making good the disturbed portion of concrete surfaces with 1:2:4 type B0 (using 12.5mm graded stone aggregate) complete all as specified and directed by Engineer-in-Charge.
Material and Labour for preparation of newly plastered surfaces of wall, applying two coats of Oil emulsion distemper over a coat wall care putty of 3mm thick and alkali primer complete all as specified and directed by Engineer-in-Charge.
Material and Labour for complete removal of existing treatment on wall surfaces and applying a coat of wall care putty 3mm thick on plastered surfaces, preparatory to distempering and applying two coats of oil bond distemper over coat of wall primer complete all as specified and directed by Engineer-in-Charge.
Material and Labour for preparation of new plastered surface of any description over 10 cm width or girth, applying two coat of synthetic enamel paint over a coat of primer complete all as specified and directed by Engineer-in-Charge.
Material and Labour for preparation of newly plastered surfaces in ceiling, applying three coats of white wash complete all as specified and directed by Engineer-in-Charge.
Material and Labour for preparation of newly plastered or un plastered wall surfaces, over 10cm girth applying two coats of 100% acrylic, weather resistant emulson over a coat of exterior wall primer complete all as specified and directed by Engineer-in-Charge.
Dismantling timber scantlings 40 sq. cm and over in section, in any position in unframed work. Note :- Wooden scantling will not be taken on Schedule of credit. It will be handed over to MCM department of Naval Dockyard Mumbai order by competent authority.
Supply and Fixing 1st class hardwood (TEAK WOOD) Plain, solid, straight, rebated on the solid, rounded or chamfered segmental supplied and fixed (size of wooden planks ( 3000 mm x 300 mm x300 mm ). complete all as specified and directed by Engineer-in-Charge.
Supply and Fixing 1st class hardwood (TEAK WOOD) Plain, solid, straight, rebated on the solid, rounded or chamfered segmental supplied and fixed (size of wooden planks ( 2000 mm x 300 mm x300 mm) complete all as specified and directed by Engineer-in-Charge.
Supply and Fixing 1st class hardwood (TEAK WOOD) Plain, solid, straight, rebated on the solid, rounded or chamfered segmental supplied and fixed (size of wooden planks ( 1000 mm x 300 mm x 300 mm) complete all as specified and directed by Engineer-in-Charge.
Supply and fix anchor bolt fastners of size 500mm long and 30mm dia including drilling holes in timber, concreting and grouting as required and directed by Engineer in charge. Note: In case of non availability of required length and dia of fastener bolt, next higher size as available in market will be used for work without any extra price adjustment.
Material and Labour for preparation of new decorated wooden surfaces of any description over 10 cm width or girth, applying two coat of synthetic enamel paint over a coat of primer complete all as specified and directed by Engineer-in-Charge.
Material and Labour for preparation of old wooden surfaces of any description over 10 cm width or girth, applying a coat of synthetic enamel paint of approved colour complete all as specified and directed by Engineer-in-Charge.
Material and Labour for complete removal of existing plastered wall surface, over 10cm girth preparation of surfaces, applying two coats of 100% acrylic, weather resistant emulson over a coat of exterior wall primer complete all as specified and directed by Engineer-in-Charge.
Material and Labour for epoxy base joint filler paint on external surfaces of walls/floor to fill the cracks with and including resin and hardner in proportion as per manufacturers instructions complete all as specified and directed by Engineer-in-Charge.
Material and Labour for preparation of new steel surfaces exc 10 cm width or girth and applying two coats of epoxy paints over a coat of red oxide primer complete all as specified and directed by Engineer-in-Charge.
Material and Labour for preparation of old steel surfaces exc 10 cm width or girth and applying two coats of epoxy paints over a coat of red oxide primer complete all as specified and directed by Engineer-in-Charge.
Removing excavated material & debris exc. 1.50 Km but n exc. 15 Km and depositing where directed, in soil complete all as specified and directed by Engineer-in-Charge.
Material and Labour for preparation and applying two coat of floor/Roof paint (Make-Indigo Floor paint or equivalant as approved by GE) complete all as specified and directed by Engineer-in-Charge.
Shree Ayyappa Engineering
RAJENDRA CONSTRUCTION
M/s S.D Construction Co
stage.html
html • 0.05 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .