CA NO.CWE BLY/GE (E)/69 OF 2025- 2026PROVN OF PARKING SHED FOR MD ACCN FOR JCOs/OR FOR BLDG NO T-163, T-164 and T160 (22 QTRS) OF INF BN-II AT MADHUBAN COMPLEX AT SHAHJAHANPUR CANTT UNDER GE EAST BAREILLY

Amount

Surface excavation n.exc. 30cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and directed.

Excavating in trenchs, n exc 1.5m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10sq m on plan and n exc 1.5m in depth and getting out in Soft/loose soil complete all as specified and directed.

Returning filling in, including spreading, levvelling, waterning and well ramming in layers not exc 25cm thick complete all as specified and directed.

Removing excavated materials n. exc 50m and deposited where directed at a level n. exc 1.5m above the starting points complete all as specified and directed.

M&L for cement concrete 1:4:8 type D2 using 40mm graded stone aggregate for foundation filling and mass concrete complete all as specified and directed.

M&L for M-25 (20 mm graded stone aggragates) design Mix concrete for foundation, including raft footings, foundation beams, plinth beams, bases for column etc. basement slabs and mass concrete complete all as specified and directed.

M&L for M-25 (20 mm graded stone aggragates) design Mix as in beams, cantilvers, lintels over 1.50m span complete all as specified and directed.

M&L for M-25 (20 mm graded stone aggragates) design Mix as in columns, pillars etc. complete all as specified and directed.

M&L for M-25 (20 mm graded stone aggragates) design Mix as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Use and waste formwork to sides of concrete foundations, footings, bases of columns, plinth beam, sides and soffits of plinth beams and similar works in vertical or to batter of rough finished flat surfaces of concrete complete all as specified and directed.

Use and waste formwork square, rectangular or polygonal to sides of columns, pillars etc. of rough finished flat surfaces of concrete complete all as specified and directed.

Use and waste Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. complete all as specfied and directed.

Use and waste formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) rough finished surfaces of concrete complete all as specified and directed.

M&L for formwork to edges of concrete rough finished surface flats, treads, breaks in floors, window cills, concrete railings, opening in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10 cm but n exc 20 cm for rough finished surface complete all as specified and directed.

M&L for TMT bars, 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) but not less than 0.9 mm dia conforming to Fe-410 - 0, complete all as specified and directed.

M&L for TMT bars, 5 mm dia and over upto and including 10 mm dia, cut to length, bent to shape required, as in binders, stirrups, spacer and binding with mild steel wire (annealed) but not less than 0.9 mm dia conforming to Fe-410 - 0, complete all as specified and directed.

M&L for brick work with sub class 'B' bricks old size in cement mortar 1:6 straight or curved on plan exc. 6.00m mean radius complete all as specified and directed.

M&L brick work with fly ash bricks straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and directed.

M&L for 15 mm thick rendering on fair brick surfaces or concrete surfaces in cement mortar 1:6 finished even and fair complete all as specified and directed.

M&L for 15 mm thick rendering on brick surfaces or concrete surfaces (on external surface) in cement mortar 1:4 finished even and smooth without using extra cement and mixed WPC @ 3% of cement weight complete all as specified and directed. Note :- WPC shall be measured and paid separately

Supply only integral water proofing compound complete all as specified and directed.

M&L for rendering 5 mm thick on ceiling or concrete surfaces in cement mortar 1:3 surface even and smooth without using extra cement complete all as specified and directed.

M&L for preparation of new plastered wall surface and applying three coats of white wash complete all as specified and directed.

M&L for preparing newly plastered surfaces of walls and applying two coats of cement base paint over a coat of primer complete all as specfied and directed.

M&L for preparing newly plastered surfaces of ceiling and applying three coats of white wash complete all as specfied and directed.

M&L for preparation of sunken floor and applying a coat of hot bituminous primer @ .30 kg/sqm and applying a coat of industrial bitumen 85/25 @ 1.20 kg/sqm over primer and laying modified polymeric water proofing membrane(weight not less than 3 kg/sqm 2 mm thick consisting 100 mm micron HMHDE FILM ) and applying one coat of industrial btumen grade 85/25 @ 1.2 kg/sqm on top of membrane with 100 mm overlap at side end lap where required over 10 mm thick rendering in CM 1:4 including integral waterproofing compound 3% and taking down existing plastering as per manufacturer instruction and complete all as specified and directed

M&L for Providing precast cement concrete louvres and jallies, 25mm thick (measured solid), 1:2:4 type B0 (using 12.5 mm graded stone aggregate) including mouldings but excluding frame set in cement mortar 1:4 complete all as specified and directed.

S&F mild steeldoor with angle iron 50x50x6 mm frame & shutter with 40x40x5mm frame with flat iron support 40x6 mm 4 Nos with plain black sheet 1 mm thick Mild steel, in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified and directed.

M&L for preparation of newly or previously untreated of steel surfaces of any description, over 10cm in width or girth, and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for Moorum/ red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed.

M&L for hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for 75 mm thick PCC type D-2, 1:4:8 ( usng 40 mm graded stone aggregate) as in sub base complete all as specified and directed.

M&L for PCC 1:3:6 type C-1 (using 20mm graded stone aggregate) as in plinth protection 75 mm thick finished even and smooth without using extra cement complete all as specified and directed.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed.

M&L for concealed point wiring for one light/ fan point controlled by one switches with cable 1.5 sqmm size PVC nsulated (unsheathrd) copper conductor cable, PVC insulated unsheathed FRLS cable complete with all fittings and accessories but using existing sunken cast iron or pressed steel terminal box for mounting of switches, fan regulators etc but providing new cover 3mm thick laminated, (Hylem) sheet top cover fastened with chromium plated screws and 1.5 Sqmm PVC insulated unsheathed copper conductor FRLH cable as continues earth wire connected to common earth dolly completed all as directed and as specified for the following :-

All as per item Sr No. 35 one 3-pin socket outlet 5 Amp on independent board complete all as specified and directed.

All as per item Sr No. 35 one 3-pin socket outlet 5 Amp on same board complete all as specified and directed.

All per Srl item No. 35 here-in-before, but with 2.5 Sqmm copper conductor cable complete all as specified for One 3 pin socket outlet 15 Amp on independent board complete all as specified and directed.

S&F switch piano flush type polycarbonate SP one way 5 Amps complete all as specified and directed.

S&F switch piano flush type polycarbonate SP one way 15 Amps complete all as specified and directed.

S&F socket out let 3 pin 5 amp multipurpose flash type complete all as specified and directed.

S&F socket out let 3 pin 5/15 Amp multipurpose, flush type 240 volt complete all as specified and directed.

S&F ceiling rose surface Bakelite 65 x 50 mm two to three terminals complete all as specified and directed.

S&F for lamp holder insulated body of PVC/ polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

S&F LED Bulb 9 Watt complete all as spcecified and directed.

S&F MCBs SP 6-32 Amps breaking capacity 10 KA 'B' series 240 volts 50 Hz complete all as specified and directed.

S&F MCB SPN 32 Amps breaking capacity 10 KA 'B' series 240 volts 50 Hz complete all as specified and directed.

S&F in replacement MCB DB Single pole and neutral 8 way sheet steel phospetised powder painted with 200 amps rated bus bar with IP 43 protection 240 V nautral link, earth bar and Din rail double door complete all as specified and as direcrted.

S&F LED lights fitting 1x 20W, 220V,AC decorative batten type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose with suitable size complete all as specified and as directed.

M&L for earthing complete with galvanized steel earth plate electrode 60cm×60cm× 6mmmm thick, buried directly in ground, vertically to a depth not less than 2.25 mtr deep below ground level with top edge of the earth plate at depth not less than 1.5 mtr below ground level earth plate surrounded by 15 cm thick and packed layers of charcoal, dust and common salt, earth lead GI wire 4mm dia by means of bolts, nuts, check-nuts and washers of galvanized iron and thimbles and of earth wire protected by galvanized iron pipe light grade 15mm bore and water pipe 20 mm bore GI medium grade with funnel and wire mesh complete including excavation and earth work, PCC chamber and cover in cement concrete 1:3:6 type C-1 using 20 mm graded stone aggregate in lieu of CI cover and frame etc all as specified and shown in electrical plate No. 5 of SSR-2009 (Part-I) including testing after completion complete all as specified and dirfected.

Taking down old unserviceable building security light and S&F new energy saving LED light fitting 35 Watt made up of pressure die cast aluminium housing with acrylic cover as diffuser with IP 66 protection and impact resistance of IK07 as required to be mounting bracket in wall/ floor to suit the opening of the fitting with FI clamp nut bolt and washers of suitable size including making connection complete all as specified and dirfected.

M&L for GI bracket made out of 25 mm GI pipe light grade 1.20 m length bend to shape including clamps nuts bolt and washer and fixing to wall/ floor complete all as specified and dirfected.

Supply, laying and testing XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area, 16 sqmm 4 core including taking down old cable from trenches etc. complete all as specified and directed.

M&L sand cushioning underground cable in trenches below and around underground cable including spreading and levelling punning complete all as specified and directed.

Supply and laying sub class 'B' old size brunt bricks for protection of cable, in trenches, laid in dry flat across the cable with length of whole bricks complete all as specified and directed.

M/S CHAUHAN ELECTRIC WORKS (BID ID -3496002)