CELZ/ALD/T-27 OF 2021-22

Amount

Sch 'A' Part-I (Building & Structure Work) Note : This schedule is pre-priced by MES and the pre-priced rate indicated are under Col. 5.

Total amount of Sch 'A' Part II (Site clearance, excavation and earth work)

Total amount of Sch 'A' Part III (Internal Water Supply )

Total amount of Sch 'A' Part IV (Internal Electrification)

Total amount of Sch 'A' Part V (Sewage Disposal)

Total amount of Sch 'A' Part VI (Road, Path , Culvert )

Total amount of Sch 'A' Part VII (Area Drainage)

Total amount of Sch 'A' Part VIII (External Water Supply )

Total amount of Sch 'A' Part IX (External Electrification )

Total amount of Sch 'A' Part X (Improvement to living accn of guard room at Guard Post No 1 to 16 )

Sch 'A' Part - XI (Miscellaneous Items) Note - This Schedule as given here- in -after is not pre-priced by MES and the pre - priced rate indicated as "Rs 0.00 under col.5 siginifies this fact only.

INTERNAL WATER SUPPLY S& F in repair one way angle valve, cast copper alloy , screwed down, high pressure, crutch or butterfly handle for iron pipe or for unions 15 mm bore complete all as specified and directed.

S& F stainless steel peg set of five complete all as specified and directed.

INTERNAL ELECTRIFICATION M&L for point wiring complete with PVC insulated and unsheathed 1100 volt, FRLSH cable 1.5 sqmm (nominal area), ISI marked,multi stranded copper conductor cable including ISI marked 20mm dia medium grade PVC conduit concealed in wall , roof/floors, factory made pressed steel concealed terminal boxes not less than 1.6mm thick of reqd size and with top cover 3mm thick of plastic laminated sheets of required colour complete,including 1.5 Sqmm PVC insulated ,FRLSH cable unsheathed multi stranded copper earth wire and connecting to common earth dolly,including colour coding of cable shall be Phase-red,Neutral-black and Earth- green with all accessories and all as specified and directed for One light/Fan/Exhaust fan/Bell point controlled by one switch Note :- In case of roof/ceiling, heavy duty PVC pipe shall be used without any extra cost.

M&L for point wiring complete with PVC insulated and unsheathed 1100volt ,FRLSH cable 1.5 sqmm (nominal area), ISI marked,multi stranded copper conductor cable including ISI marked 20mm dia medium grade PVC conduit concealed in wall , roof/floors, factory made pressed steel concealed terminal boxes not less than 1.6mm thick of reqd size and with top cover 3mm thick of plastic laminated sheets of required colour complete,including 1.5 Sqmm PVC insulated ,FRLSH cable unsheathed multi stranded copper earth wire and connecting to common earth dolly,including colour coding of cable shall be Phase-red,Neutral-black and Earth- green with all accessories and all as specified and directed for One 5 pin 5 Amp switch socket out let point on an independent board

M&L for point wiring complete with PVC insulated and unsheathed 1100 volt ,FRLSH cable 1.5 sqmm (nominal area), ISI marked,multi stranded copper conductor cable including ISI marked 20mm dia medium grade PVC conduit concealed in wall , roof/floors, factory made pressed steel concealed terminal boxes not less than 1.6mm thick of reqd size and with top cover 3mm thick of plastic laminated sheets of required colour complete,including 1.5 Sqmm PVC insulated ,FRLSH cable unsheathed multi stranded copper earth wire and connecting to common earth dolly,including colour coding of cable shall be Phase-red,Neutral-black and Earth- green with all accessories and all as specified and directed for One 5 pin 5 Amp switch socket out let point on same board

M&L for point wiring complete with PVC insulated and unsheathed 1100volt ,FRLSH cable 1.5 sqmm (nominal area), ISI marked,multi stranded copper conductor cable including ISI marked 20mm dia medium grade PVC conduit concealed in wall , roof/floors, factory made pressed steel concealed terminal boxes not less than 1.6mm thick of reqd size and with top cover 3mm thick of plastic laminated sheets of required colour complete,including 1.5 Sqmm PVC insulated ,FRLSH cable unsheathed multi stranded copper earth wire and connecting to common earth dolly,including colour coding of cable shall be Phase-red,Neutral-black and Earth- green with all accessories and all as specified and directed for One light point controlled by two 2-way switches

M&L for point wiring complete with PVC insulated and unsheathed 1100 volt ,FRLSH cable 2.5 sqmm (nominal area), ISI marked,multi stranded copper conductor cable including ISI marked 20mm dia medium grade PVC conduit concealed in wall , roof/floors, factory made pressed steel concealed terminal boxes not less than 1.6mm thick of reqd size and with top cover 3mm thick of plastic laminated sheets of required colour complete,including 2.5 Sqmm PVC insulated ,FRLSH cable unsheathed multi stranded copper earth wire and connecting to common earth dolly,including colour coding of cable shall be Phase-red,Neutral-black and Earth- green with all accessories and all as specified and directed for One 5 pin 15 Amp switch socket out let point on an independent board /Two pin earth plug and socket

Supply and fixing Tele phone socket ISI marked all as specifed and directed.

Supply and fixing Switch flush type 5/6 Amps single pole two way 240 volt complete all as specified and dierected.

S&F LED Building security light fitting with aluminum pressure die cast housing, high purity PC Fresnel diffuser with silicon gasket for IP-65 protection, power consumption <20 W (14W) & luminaire lumen >2500 lm and system efficiency > 120 lm/W, in built electronic driver prewired upto terminal block with driver efficiency >85% power factor >0.95 as light source with toughened glass including two core flexible copper wire of 1.5 sq mm from ceiling rose to the connector of fitting, connection wires not to be more than 2.5 in length and made out of GI tubing 35/40 mm dia /suitable dia light grade bend to shape security light fitting with necessary MS clamp 25 mm wide and 6 mm in thickness in suitable length not more than 30 CM and max length of pipe 1.5 Mtr long with one code of anti corrosive primer and two coats aluminum paint including nuts, bolts and washers complete all as specified and directed.

S&F Mirror light Decorative ultra slim square profile liner LED lighting fixture with extruded polycarbonate body with Minimum 8 Watt & Maximum 11 Watt LED warm white in colour with a luminous efficacy of 120 lum/watt(min) with PF not less than 0.9 with LED binning as per ANSI Bin C78.377A, photo biological safety report as per IEC624718 & electrical insulation class I, Ingress protection IP 20, colour rendering index CRI>80, temp range 0 to 450C, driver efficency>85%, power factor>0.9, THD <20% as per IEC 61000-3-2, colour temp -6500K, surge protection 2.5 KV, 50000 burning hrs (min) as per L70 criteria, two stages isolated constant current operated driver with range 150-270V AC and seafty extra low voltage safe level <60V DC as per IEC standard with LM70 & LM80 certification.complete all as specified and directed.

S&F circular slim surface LED downlighter of 8 Watts with housing made up of die cast aluminum for better thermal management, high transmitivity non yellowing PMMA diffuser for better light output and uniform light distribution without glare, power consumption <10W, luminaire lumen>1000lm, driver and accessories to be prewired, CRI>70, LED efficiency > 120 lm/W photo biological safety report as per IEC624718 & electrical insulation class I, LED life with L70 criteries -37000 hrs colour temp >6000K, Ingress protection IP-20, ambient temperature 0 to 450C, driver efficiency >85%, THD<10% as per IEC 61000-3-2, power factor >0.95, surge protection 2.5 KV, two stages isolatated constant current operated driver with range 150-270V AC and safety extra low voltage safe level <60V DC as per IEC standard with LM79 & LM80 certification.

S&F circular slim surface LED Decorative Wall mounting of 12 Watts with LED Bulb 12 watts complete Polycarbonate housing, globe type Glass protection with high transmitivity non yellowing PMMA diffuser for better light output and uniform light distribution without glare, power consumption <12W, luminaire lumen>1000lm, driver and accessories to be prewired, CRI>70, LED efficiency > 120 lm/W photo biological safety report as per IEC624718 & electrical insulation class I, LED life with L70 criteries -37000 hrs colour temp >6000K, Ingress protection IP-20, ambient temperature 0 to 450C, driver efficiency >85%, THD<10% as per IEC 61000-3-2, power factor >0.95, surge protection 2.5 KV, two stages isolatated constant current operated driver with range 150-270V AC and safety extra low voltage safe level <60V DC as per IEC standard with LM79 & LM80 certification.

M&L Submain wiring with two single core 2.5 sqmm 1100 volt FRLSH copper conductor, PVC insulated, multistranded, unsheathed cable ISI marked including ISI marked 20mm dia medium grade PVC conduit concealed in wall surface / ceiling for sub main connection including 2.5 sqmm FRLSH cable PVC insulated multistranded unsheathed copper conductor used as earth wire to common earth and connection to earth dolly complete all as specifie. NOTE : (Two runs of single core cable with one run of earth continuity conductor including PVC conduit accessories shall be measured and paid as one unit length.) including making good disturbed surface all as specified and directed.

Supply and fixing motor operated swivelling (rotating) type high intensity, weather proof, 1 x 400 Watts MH search cum flood light, 230 Volt AC, having high efficiency mirror back glass & SS reflector, covered a effective range upto 800 mtrs, 360 degree continuous rotation in horizontal plane. The front housing of luminarie should be made of 3mm thick low carbon Aluminium alloy with die-cast backhousing, toughened glass should be made of 5mm thick with endless neoprene rubber gasket with E-40 ceramic lamp holder. the whole fitting should be painted by epoxy powder coated conforming to IS:10322, fitting should be installed on fibre based rotating disc of revolving mechanism with suitable motor, inbuilt speed reduction unit 5 RPM and also provide revrse forward facility. The complete rovolving mechanism should be covered with epoxy cum poder coated and also covered y MS/Fiber box for corrosion resistant, aesthatic look and suitable for outdoor installation, including control panel with fuses, MCB and indicators and suitable size cable from panel board to search lights etc. complete all as specifed and direted . Make : KALIN Cat Part No: LRF25SS/G401 or equivalent make in Philips/Crompton/ Bajaj

Supply and laying or fixing or passing through pipe, 1100 volts grade heavy duty cable with PVC insulated aluminium stranded conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed 2 core 10 sq. mm nominal cross section in service connection.

Taking down main switches, distribution boards and cut outs etc. of any type and capacity and removing the same from site and keeping in safe custody for resuse issue on credit to contractor as directed by Engr in Charge and making good the disturbed surface/portion of walls all as directed by Engr-in-Charge.

Taking down carefully sub main wiring of any nos of wire and size with earth wire on wooden batten/surface conduit/casing caping complete with its all accessories.

M&L sub main wiring of two run 6 sqmm single core FRLS PVC insulated, unsheathed multistranded copper conductor cable 1100 Volt grade, drawn through and including PVC conduit medium duty and accessories of size not less than 20 mm size ISI marked including all conduit accessories for concealed to the surfaces of the wall/ceiling including one run of 6 sqmm single core FRLS PVC insulated unsheathed copper earth continuity conductor all as specified and as directed. NOTE : (Two runs of single core cable with one run of earth continuity conductor including PVC conduit accessories shall be measured and paid as one unit length.) including making good disturbed surface all as specified and directed.

S&F for LED tube light fitting 1 x 18 watt, LED 6000 K wall mounted batten, extruded fire retardent plastic body , integrated electronic driver , ultra slim linear LED lighting fixture with, environmental friendly , energy efficient complete with all accessories, prewired and making connection with and including 23/0.0076 flexible copper wire three core from connector to ceiling rose not more than 1.2 mtr, fixed on wall firmly complete all as specified and directed. Make : Philips Model No Smart Bright Cat Part No: BN021C LED20S PSU CDL GR/ Crompton Trim Lenia Cat No. LCTL -18 CDL or equivalent of Havells

S & F 1100 Volts grade heavy duty cable of size 10 Sqmm twin core with PVC insulated aluminium conductor,served with inner seathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire,complete all as specified and directed.

EXTERNAL ELECTRIFICATION Refixing of steel tubular swaged poles type 410 SP- 31 (9.0m long pole) complete with cast iron base plate, final taper plug, bolts,nuts and screws complete all as specified including consisting of following works:- (a) Excavation in trenches not exceeding 1.5 mtr wide & 1.57 mtr deep for pole foundation & getting out in soft/loose soil, returning filling in the excavated of soil after fixing the pole in foundation ramming earth around in layer not exceeding 25 cm thick and disposal of surplus soil to a distance not exceeding 50 mtrs complete all as specified and directed. (b) M&L for PCC 1:4:8, type D2 (using 40mm graded crushed stone aggregate) in foundation 600mm x 600mm cross section and planting depth 1.5 mtr for concrete encasing the pole upto GL complete all as specified and directed. (c) M&L for providing PCC 1:3:6, type C-1 (using 20mm graded crushed stone aggregate) for plinth block/collar above GL 500mm high and 450mm dia complete all as specified and directed.

M&L for painting of existing 9 metre steel pole with cross arms and clamp of any length and shape for LT overhead line/street light pole with one coat of aluminium paint including preparation of the existing surface including making number in a 15cm dia yellow circle and marking three black & two yellow bends with 10 cm width byu fluorescent paint, from coping of pole to 1.5m height on pole including painting of coping with white wash with safety precaution & all disconnected electrical connections are connected and before painting shut down complete all as specified & directed.

S&F stay assembly (in replacement) consisting of galvanised stay wire 7/10 SWG stay bow of 14 mm dia, stay rod 16mm dia 180cm long with loop insulators stay plate 230 x 230mm x6mm with PCC foundation 1:3:6 type C2 complete with stay clamps,bolts and nuts all as specified and directed by Engr-in-Charge including the following :- (a) Excavation and earth work for stay foundation in soft/loose soil,disposal of surplus soil to a distance n. exc. 50 metres & depositing where directed at a level n. exc. 1.5mtr from the starting point as specified and directed. (b) PCC 1:3:6,type C-2(using 40mm graded stone aggregate) as in embedding blocks all as specified and directed.

S&F motor operated swivelling (rotating) type high intensity,weather proof ,1 x 400 Watts MH search cum flood light, 230 Volt AC, having high efficiency mirror back glass & SS reflector, covered a effective range upto 800 mtrs,360 degree continuous rotation in horizontal plane. The front housing of luminarie should be made of 3mm thick low carbon Aluminium alloy with die-cast back housing, toughened glass should be made of 5mm thick with endless neoprene rubber gasket with E-40 ceramic lamp holder. The whole fitting should be painted by epoxy powder coated conforming to IS:10322, fitting should be installed on fibre based rotating disc of revolving mechanism with suitable motor, inbuilt speed reduction unit 5 RPM and also provide reverse forward facility. The complete revolving mechanism should be covered with epoxy cum powder coated and also covered by MS/Fiber box for corrosion resistant, aesthatic look and suitable for outdoor installation,including control panel with fuses, MCB and indicators and suitable size cable from panel board to search lights etc. complete all as specified and directed. MAKE: KALIN Cat Part No: LRF25SS/G401 or equivalent make in Crompton/Bajaj/Philips

Refixing, connecting & testing existing LED street/security light fitting on street light pole all as specified & directed.

Supply and drawing single core copper conductor cable of size 2 x 4.0 Sqmm and 1 x 2.5 Sqmm copper cable inside the steel pole to LED street light fitting complete all as specified and directed

DEORA ELECTRIC WORKS