WBPWD/AE/NRSH/NIT-27/2025-26_3

Cement concrete (1:1.5:3) with graded stone chips 5.6 mm size with hexagonal square mesh wire netting, I.R.C. fabric mesh or X.P. M. fitted and fixed after tying the existing reinforcement on concrete without distributing the same and with proper scarping and cleaning the reinforcement and disturbed concrete with wire brush etc. after applying a coat of cement including the cost of wire netting I.R.C or X. P. M. & cost of all handling and scaffolding complete as per direction of Engineer-in -charge.

b) 25 mm thick

Plaster ( to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering conrners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (ground floor). [Excluding cost of chipping over concrete surface].

(ii) With 1:4 cement mortar .

(c)10 mm. thick plaster. (Add. above ground floor - 1st. floor)

(i) with 1:6 cement mortar.

(b) 20 mm. thick plaster. (Add. above ground floor - 1st. floor)

Applying interior grade acrylic primer of approved quality and brand on plastered or concrete surface old or new surface to received distemper /Acrylic emulsion paint including scraping and preparing the surface thoroughly , complete as per manufactured specification and as per directions of the EIC.In ground floor.

(a) one coat.

(i) water based interior grade Acrylic primer.

Applying acrylic emulsion paint of approved make and brand on walls and ceiling including sand papering in intermediated coats including putty ( to be done under specific instructions of superintending engineer): (two coats).

(i) standard quality.

(i) Hydraulic door closer of approved quality as per I.S.I. standard fitted and fixed complete :.

(b) Medium (I.S.I. size 2).

Supplying bubble free float glass of approved make and brand. Conforming to IS: 2835-1987.

(iv) 5 mm thick coloured / tinted / smoke glass.

Supplying, fitting & fixing of Aluminium fixed partion wall of all aluminium sections viz top,bottom and side member, intermediate member , glazing clip made of Aluminium Alloy Extrusions conforming to IS: 733-1983and IS: 1285-1975, annodized conforming toIS:1868-1983, fitted with all other accessories viz. EPDM gusket,cleat, angle screws etc. including labour charges for fitting and fixing of aluminium fixed partition wall with glass / panel board all complete asper architectural drawings and direction of Engineer-in-charge.( Excluding cost of glass/ panel board,10-12 Micron thickness Annodizing film.Natural white.

a) for unsupported length of vertical member upto 1.50m. height of both ends of vertical member restrained but panel with in 0.90sqm

Supplying and laying true to line and level Double Charge Vitrified Tiles of approved brand conforming to IS 15622:2006 (Group B I a) and tested as per IS 13630:2006 (relevant parts) [Non-modular sizes for tiles with Water Absorption (av.)≤ 0.08 %] in floor, skirting etc. using polymerised adhesive of 6mm thick layer applied directly over finished artificial stone floor/Mosaic etc without any backing course and joints grouted with admixture of white epoxy grout materials of approved brand including spacer -2mm as directed and removal of wax coating of top surface of tiles with warm water and polishing the tiles using soft and dry cloth upto mirror finish complete including the cost of materials,Iabour and all other incidental charges complete as per direction of Engineerin-Charge. (Note: This work should not be executed without specific permission of Superintending Engineer

(a) ln Ground FIoor:(size not Iess than 600mmX 600 mm X 9.5mm thick) (Add. above ground floor - 1st. floor) (Add. above ground floor - 1st. floor)

Please Enable Macros to View BoQ information