PROVN OF 01 X TOILET BLOCK AT TRG AREA OF CICE OF HQ MEG AND CENTRE AND RENOVATION OF VISITORS TOILET FOR VETERANS NOK DEPEDENTS AT BLDG NO. P-140 AND P-141 OF RECORDS MEG AND CENTRE UNDER GE (NORTH) BANGALORE

M&L for PCC (1:4:8) type D2 using 40mm graded stone aggregate as in foundations, filling and mass concrete complete all as specified and directed.

M & L for rendering 10 mm thick cement mortar (1:6) on brick or concrete surfaces finished even and smooth without using extra cement etc complete all as specified and directed.

Note for Item No. 140 :- (i) The earth wire for the points in the same circuit can be looped from point to point (ii) Earth wire shall be taken inside the conduit (iii) Quoted rate is deemed to be included cost of terminal box (iv) Quoted rate is deemed to be included any length of cable from DB to any switch/ socket board to be included in point wiring.

Material and labour for Pre-cast cement concrete (1:3:6) type C-1 using 20 mm graded stone aggregate as in solid block masonry exc. 10 cm in width and setting in cement mortar (1:6) complete all as specified and directed.

M & L for rendering 5mm thick cement mortar (1:3) on ceiling concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

Material and labour for screed bed or bedding layer 20mm thick cement mortar (1:4) for laying of tiles complete all as specified and directed.

M&L for cement concrete (1:2:4) type B1 using 20mm graded stone aggregate as in coping,kneelers, apex stone etc complete all as specified & directed

Supply & Fix machine pressed Pre-cast cement concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80mm thickness M-40 Grade with grey cement and no pigment, coloured laid over machine compacted sand cushion all as specified and directed. (Note : Sand cushion will be measured & paid seperately)

M&L for pre cast cement concrete (1:2:4) type B1 using 20mm graded stone aggregate as in cover slab and set in CM (1:6) with top surface finished even & fair complete all as specified & directed

Material and Labour for TMT bars 10 mm dia and over cut to length bent to shape required including cranking bending spirally or hoping for columns, hooking ends & binding with and including MS wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified & directed

S & F Figured glass 4mm thick, pin head type and area n.exc 0.5 sq. m in squares each pane fixed to alluminium frame works with necessary rubber beadings etc. complete all as specified and as directed

M & L for water proofing treatment over RCC roof slab all as per following specification complete all as specified and directed :- (i) Removing all loose gravel, dirt, oil, grease and foreign materials by jet or dry air, cleaning the surfaces mechanically or by grinding to make it smooth (ii) Applying compatible primer/bonding bitumen @ 0.40 Litre/Sq m (iii) Applying APP modified water proofing membrane as per IS 1654-2017/IS 16352-2017 , 3mm thick and weighing not less than 3.60kg/Sq m reinforced with non woven polyster/HMHDPE matt black finished over and torch applications of membrane with 75mm side overlap and 100mm end lap after necessary preparation of surface complete as per manufacturer's instructions (iv) Applying a coat of solar reflective bituminous aluminum paint on top @ 0.10 litre/sq m

S & F Solid PVC Door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, supplying & fixing in opening as per specification etc complete all as specified and directed

S&F factory made solid PVC moulded door shutter with wood free EPS, 28 to 30mm thick (Stiles) with 2, 4 or 6 raised panel design with 2mm thick moulded prelam PVC sheet on the front face and 2mm plain colour PVC sheet on back face etc including necessary fittings like Hinges , tower bolts, handles complete all as specified and as directed.

Excavating in trenches, not exc 1.5 m wide and not exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and n exc 1.5 m in depth and getting out in hard / dense soil etc complete all as specified and as directed

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm thick with soil etc complete all as specified and as directed

Removing excavated soil to a distance not exc. 50 m and depositing where directed at a level not exc. 1.5 m above the starting point etc complete all as specified and as directed

M&L for Reinforced cement concrete Design Mix (M-25) using 20 mm graded stone aggregates as in foundation, including rafts, footings, plinth beam etc complete all as specified and as directed

M&L for Reinforced cement concrete Design Mix (M-25) using 20 mm graded stone aggregates as in slab supported on walls, beam and columns in floors, roofs landing balconies canopies etc complete all as specified and as directed

M&L for Reinforced cement concrete Design Mix (M-25) using 20 mm graded stone aggregates as in beam, cantilevers, bressumers, lintels over 1.5 mtr span etc complete all as specified and as directed

M&L for providing reinforced cement concrete Design Mix (M-25) using 20 mm graded stone aggregates as in column, pillars, piers, posts and struts etc complete all as specified and as directed

M&L for Providing pre-cast cement concrete (1:3:6) type C-1 using 20 mm graded stone aggregate as in solid block masonary, not exc 10cm thick setting in cement mortar 1:4, complete all as specified and as directed

M&L for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical with fair finished flat surfaces of concrete etc complete all as specified and as directed

M&L for Formwork to soffits and sides of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200m thick (Horizontal or sloping) with fair finished flat surfaces of concrete etc complete all as specified and as directed

S&F Factory made pressed steel frame of profile size 125 X 60 mm for door, made of 1.25 mm thick M S sheet with one ore more rebate includings necessary fixing lugs, hinges, locks strike plate etc complete all as specified and as directed

M&L for Plain cement concrete (1:3:6) type C-0 using 12.5mm graded stone aggregate as in hold fast and filling of pressed steel chowkat etc including necessary formwork complete all as specified and as directed

S&F Flush shutters 35mm thick, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed

M&L for Preparation of new wood surfaces of any description over 10 cm in width or girth, not otherwise described and painting with two coats of synthetic enamel paint over a coat of pink primer etc complete all as specified and as directed

S&F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded as specified and directed. NOTE : Sheet glass/figured glass and wire mesh will be measured and paid separately.

S&F Steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and as directed (NOTE : Glass and wire mesh will be measured and paid separately).

S&F Sheet glass 4mm thick of ordinary quality and glazing with oil putty or wooden beading to wooden frame or

steel frame in squares not exc 0.50 sqm in each pane complete all as specified and as directed

S & F Aluminium alloy anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections including taking down old sliding door bolt 300 mm all as specified and as directed.

S&F Aluminium anodised tower bolt 200 mm long of extruded section etc complete all as specified and as directed

M&L for Plain cement concrete (1:4:8) type D-2 using 40 mm graded stone aggregates as in 75 mm thick sub base to flooing etc complete all as specified and as directed

M & L for Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 15 mm thick screed bed in cement mortar (1:6) complete all as specified and as directed

M & L for Non - skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 15 mm thick screed bed in cement mortar (1:6) complete all as specified and as directed

S&F bib tap long body fancy type cast copper alloy chromium plated with capstan head screwed down screwed for iron pipe or brass ferrule or fixed for 15 mm dia bore pipe complete all as specified and as directed

M&L for Glazed ceramic coloured tiles of size 300X450X7mm thick as in skirting / dado, set and jointed in neat cement slurry and pointed in white or colour cement to match over & including backing coat 10 mm thick in cement mortar (1:3) complete all as specified and as directed

M&L for preparing newly plastered surface of ceiling and applying three coat of white wash etc complete all as specified and as directed

M&L for Preparing new plastered suface of walls and applying two coats Distemper Acrylic emulsion, white or tinted over a coat of primer etc complete all as specified and as directed

M&L for Preparation of new steel and iron surfaces of any description, over 10 cm in width or girth , not otherwise described and painting with two coats of synthetic enamel paint over a coat of red oxide primer etc complete all as specified and as directed

S&F CPVC pipes 25 mm dia bore, SDR 11 and plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified

S & F Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe 25 mm dia bore complete all as specified and as directed [Minimum weight for 25 mm – 455 gms] .

S&F Rotational moulded polythylene water storage tanks 1000 ltrs capacity, triple layered, (cylindrical or vertical with closed top) hoisted and fixed in position, complete all as specified and directed.

S & F Gun metal, globe or gate valve with iron wheel head screwed both ends for iron pipe 25 mm dia bore etc complete all as specifieid and as directed

S&F Pillar taps fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed all as specified and as directed

S&F stop valves /Angle Stop cock fancy type chromium plated brass cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions fixed for 15 mm dia bore pipe complete all as specified and as directed

S & F Towel rail rail, 20mm dia, D type, 60cm long between flanges of brass or chromium plated complete all as specified and as directed.

S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and as directed.

S & F PVC connection 15 mmdia 450mm long with PTMT nuts all as specified and as directed.

S&F vitreous china squatting pan ORISSA pattern of size 580X440 mm white with integral foot rest 'P' trap including connecting to trap and flush pipe anti-symphonage pipe etc complete all as specified and as directed

S&F vitreous china wash down water closet pan (pedestal pattern), white including fixing bolts, connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc., including Plastic water closet seat, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and as directed

S&F PVC flushing cistern with flush out valve low level of 10 Ltr capacity white with inlet ball valve, float, flushing bend & handle including brackets, etc complete all as specified and as directed

S&F Vitreous China wash basin, white, flat back / oval shaped size 550x440mm, including brackets, PVC waste pipe 610 mm long and PVC connection 450 mm long complete all as specified and as directed

S&F Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe including providing and fixing plugs, beddings urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe 40 mm bore, waste stainless steel coupling and LDPE pipe 600 mm long complete all as specified and as directed

M&L for Granite 18-20 mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed

M&L for Screed bed/rendering 10 mm thick in CM (1:4) on fair faces of brick work or concrete roof surface mixed with water proofing compound finished even & smooth etc complete all as specified and as directed Notes : WPC shall be measured and paid seperately

S&F PVC (SWR) gully trap 125/110 mm dia, setting and jointing with solvent cement complete all as specified and directed.

S&F PVC (SWR) pipes 110mm dia , single socketed in any length with rubber ring joint laid in trenches or in floor complete all as specified and directed

S&F PVC (SWR) pipes 75mm dia, single socketed in any length with rubber ring joint laid in trenches or in floor complete all as specified and directed

S&F PVC (SWR) pipes 75mm dia, single socketed in any length with rubber ring joint fixed to wall complete all as specified and directed

S&F PVC (SWR) bends (any radius) with access door of 75mm dia.

S&F PVC (SWR) vent cowls of 110mm dia complete all as specified and directed

S&F PVC (SWR) vent cowls of 75 mm dia complete all as specified and directed

Filling under floors Spreading and levelling in well layers not exc 25 cm thick including watering, well ramming etc complete all as specified and as directed

M&L for Hardcore with broken stone or boulder of gauge not exc 63mm, deposited, spread and levelled in layers not exc 15 cm thick water and rammed to a true surfac etc all as specified and as directed

Surface excavation not exceeding 30 cm deep and averaging 15cm deep and getting out in hard / dense soil etc complete all as specified and as directed

M&L for Plain cement concrete (1:4:8) type D-2 with using 40 mm graded stone aggregates) as in 100mm thick sub base to flooing etc complete all as specified and as directed

Material and labour for Chequered cement concrete tiles of size 30cmx30cmx25mm thick, set, jointed and pointed with white cement and pigment in floors complete all as specified and directed.

M&L for Pre-cast Cement concrete (1:3:6) Type C-1 using

20 mm graded stone aggregates as in solid block masonary exc 10 cm in width and setting in cement mortar (1:4) all as specified and directed.

M&L for PCC (1:2:4) type B-0 using 12.50 mm graded stone aggregate as in surface channels and drains complete all as specified and directed.

M & L for Rendering 10 mm thick cement mortar (1:4) on fair faces of brick/concrete surfaces finished even and smooth without using extra cement complete all as specified and directed

M&L for Plain cement concrete (1:3:6) type C-2 using 40mm graded stone aggregate as in bed to drain pipes 150mm dia including packing under and haunching against the sides of pipe after they are laid & tested complete all as specified and directed.

M&L for DWCPE sewage pipe line 150mm dia, class SN-8 including sealing joints etc complete with collars complete all as specified and directed.

M&L for cutting into existing manholes for connecting new drains, internal dia of pipe 150 mm, making good to pipe and rendering, cutting out existing benching for and foring branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 tye B-1 smooth finished, and re-forming benching as required etc complete all as specified and as directed

Material and labour for point wiring with 1.5 Sqmm (for Phase and Neutral) PVC insulated unsheathed multistranded, copper conductor FRLSH cable of 1100Volts grade conforming to IS - 694 drawn through and including non metallic rigid PVC conduit medium grade, ISI marked, 20mm bore with conduit accessories concealed in wall/floor and fixed on ceiling/ roof/ truss/ columns etc, including provision of factory made branded galvanized steel pressed terminal box (modular metal flush box) 1.0mm thick and suitable size modular cover plates and frames for housing the modular switches, etc., complete concealed in walls and provn of 1.5sqmm PVC insulated unsheathed copper conductor cable of green colour for earth continuity and connecting to common earth dolly etc, complete all as specified and as directed for following :-

One light point controlled by one switch

One fan/exhaust poin controlled by one switch / regulator

M&L for preparation of new surface of wall and applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces. etc complete all as specified and as directed

One 3 pin socket out let 5 A on same board

One 3 pin socket out let 5 A on independent board

S&F LED batten with luminaire suitable for indoor applications 20 Watts capacity, 4 feet long with extruded aluminium housing & integrated LED channel rectangular white arcylic cover complete with all accessories all as specified and directed.

S&F LED batten with luminaire suitable for indoor applications 10 Watts capacity, 2 feet long with polycarbonate housing & integrated LED channel rectangular white arcylic cover complete with all accessories all as specified and directed.

Supply and fix Modular switch 1 way 6Amps,1 module all as specified and directed.

Supply and fix Modular Socket, 6Amps - 2/3 pin combined 2 module all as specified and directed.

S&F in repairs MCB SPN 240 volts 40 Amps, C curves complete all as specified and as directed

S&F in repairs MCB single pole 240 volts 6 to 32 Amps, C curves complete all as specified and as directed

S&F in repairs MCB Distribution board SPN 4 way, double door type 240 volts with 200 Amps rated busbar as specified and as directed.

S & F in repairs sub main wiring 1100 volts grade multistranded FRLS copper conductors, two runs of single core 6 Sqmm along with 6 Sqm PVC insulated single core multistranded copper conductor cable as earth continuity conductor run through & including suitable size of PVC casing caping all as specified and as directed. (Note Three run of 6sqmm cable and one run of casing & caping altogether measured as one unit)

S&F ceiling rose, surface bakelite type 65 x 50 mm, 2 to 3 terminals all as specified and as directed

M&L for earthing with galvanized steel earth plate electrode 60 cm x 60 cm x 6mm thick buried directly in ground vertically to a depth not less than 2.25 mtr below ground level with top edge of earth plate at a depth not less than 1.5 mtr connected to galvanized earth lead wire 4 mm dia as earth lead up to 7.5 mtr long by means of nuts, bolts, thimbles,check nuts and washers etc made of galvanized iron connected to earthing test point all as shown in electrical plate No 3 of SSR Part-I and as specified or indicated and testing on completion including earth work and excavation in any type of soil, PCC (1:3:6) type C1 chamber, pre cast slab 40mm thick in cement concrete (1:2:4) type B1 with 8 mm dia TMT bars reinforced at 10 cm centre to centre both ways, funnel with watering pipe wire mesh and lugs, test point, including dismantaling old earthing complete all as specified and as directed

S&F in repairs LED bldg security light fitting 30Watts capacity with pressure die cast housing along with prismatic polycarbonate difuser with IP 66 protection complete all as specified and as directed

S&F in replacement Bracket made out of GI tubing medium grade 25 mm bore, approx length 1.5 m long including MS clamps made out of MS flat iron 25 x 6 mm, nuts, bolts, washers etc and including applying two coats of aluminum paint over a coat of red oxide primer complete all as specified and directed.

S&F Exhaust Fan 200mm Sweep, steel body, AC single phase, 230Volts with blade and frame and louver, connecting up wit flexible 3 core copper conductor 0.5sqmm complete all as specified and directed.

S&F Exhaust Fan 300mm Sweep, steel body, AC single phase, 230Volts with blade and frame and louver, connecting up wit flexible 3 core copper conductor 0.5sqmm complete all as specified and directed.

S&F sheet metal enclosure SPN distribution board 2 way without bus bar complete all as specified and directed

S&F MCB single pole 240 volts 5 Amps, 10Ka, C curves complete all as specified and as directed

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and as directed

S & F Switch piano, flush button, 5 Amps single pole one way complete all as specified and as directed

Excavation in trenches in soft/loose soil not exc 1.5 mtr wide and not exc 1.5 mtr in depth for laying of water supply pipe line/cable etc complete all as specified and as directed.

S&F in repairs G I tubing medium grade 40 mm dia bore with all fitting laid in trenches/walls/Roads for cable protection complete all as specified and as directed

S&F in repairs GI tubing medium grade 25 mm bore with all fitting laid in trenches/walls/Roads for cable protection complete all as specified and as directed

S&F in repairs GI tubing medium grade 20 mm bore with all fitting laid in trenches/walls/Roads for cable protection complete all as specified and as directed

S&F in repairs Gun metal Gate valve of size 20 mm dia with iron wheel head, screwed both ends for iron pipe 20mm dia and fixed all as specified and as directed

S&F in repairs Gun metal Gate valve of size 20 mm dia with iron wheel head, screwed both ends for iron pipe 25mm dia and fixed all as specified and as directed

S&F in repairs Float valve Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe 20 mm dia or brass ferrule and fixed all as specified and as directed

M & L for taking branch connection from existing distribution G I pipe 25mm dia including cutting, threading inserting G I fitting to take branch connection of 25/20mm dia all as directed

M&L for Sand cushnining for protection of cables all as per Para 19.75 of SSR part-I complete all as specified and as directed. Note :Punned thick sand will be measured for payment

Supply and lay well burnt sub class B old size bricks as protection to underground cables laying all as per Para 19.75 of SSR part-I complete all as specified and as directed.