PROVISION OF PT SHED WITH STORE FOR TRG EQPT FOR RECRUITS NEAR PT GROUND OF 1 MTR 1 STC AND ADDN/ALTN TO BLDG NO P-30 (AYUSH CLINIC) OF MH UNDER AGE B/R-III OF GE (WEST) JABALPUR

Amount

Demolition of Brick / Stone Masonry built in Cement Mortar including all quoins arches pillars etc and removing rubbish to a distance not exceeding 50 M complete all as specified and as directed.

Taking down Cement Plaster any description on brick or stone walls or concrete surfaces including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed.

Dismantling Floor, Hearth or Wall Tiling including cement mortar bedding [but not backing] and removing serviceable tiles to the stores and removing rubbish / debris of the premises complete all as specified and as directed.

Taking down chowket or frame with shutter (without taking off shutters from the frame) area not exceeding 1.5 Sqm each complete all as specified & directed.

Taking down chowkhat or frame with shutter (without taking off shutters from the frame) area exceeding 1.5 Sqm but not exceeding 4 Sqm each complete all as specified & directed.

Taking down or up steel tubing and connections for 15 mm bore of pipe complete all as specified and as directed.

Taking down or up steel tubing and connections for 20 mm bore of pipe complete all as specified and as directed.

Taking down or up steel tubing and connections for 25 mm or 32mmbore of pipe complete all as specified and as directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes,bends, swan necks etc. complete all as specified and as directed. Note : Measurement shall be of overall as fixed along the centre line over fittings and accessories.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in Soft / Loose soil, complete all as specified and as directed.

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in Soft / Loose soil complete all as specified and as directed.

Removing excavated soils n.exc. 50m and depositing where directed at a level n.exc. 1.5m above the starting point.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick of excavated soil complete all as specified and as directed. Note: A deduction of 10% shall be made from total computed volume of filling to cater in bulk irrespective of machinery used for ramming.

M & L for moorum/ red bajri filling under floors laid in layers not exceeding 15 cm thick, spread levelled and rammed / rolled including watering to required level and gradient complete all as specified and as directed.

M & L for hardcore of gauge not exceeding 63 mm of broken stones or boulders, deposited, spread and levelled in layers not exceeding 15 cm thick watered and rammed to a true surface in broken boulder complete all as specified and as directed.

M&L for RCC M-25 (Design Mix) using 20mm graded stone aggregates as in Beams, cantilevers, bressummers, lintels over 1.5m span etc complete all as specified and directed

M&L for RCC M-25 (Design Mix) using 20mm grades stone aggregate as in Columns, pillars, piers, posts and struts etc complete all as specified and as directed

M & L for RCC M-25 (design mix) using 20mm graded stone aggregates as in Slabs supported on walls, beams, columns, landings, shelves and the like complete all as specified and as directed.

M&L for RCC M-25 (Design Mix) using 20mm graded stone aggregates as in foundation including raft footings foundation beams, plinth beams, base of columns etc basement slabs, under-reamed piles and mass concrete etc complete all as specified and directed

M & L for PCC 1:4:8, Type D-2, using 40mm graded stone aggregate as in Foundation, Fillings, Mass concrete, Footings etc complete all as specified and as directed.

M & L for 40 mm thick, PCC 1:2:4, Type B-0, using 12.5mm graded aggregate as in damp proof course horizontal or vertical surfaces, including necessary form work, complete all as specified and as dire

M & L for brick work with sub class "B" bricks, old size, straight or curved on plan exceeding 6 m mean radius built in Cement Mortar 1:6 complete all as specified and as directed.

M & L for brick work with fly ash modular bricks, straight or curved on plan exceeding 6 m mean radius built in Cement Mortar 1:6 complete all as specified and as directed.

M&L for Brick work with sub class ‘B’ brick, old size, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and as directed. .

Cutting chases in brick walls, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and as directed.

M&L for Cutting holes in brick walls exc half brick and nexc one brick in cement in mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 complete all as specified and as directed.

Use and waste of form work to sides of pillars, posts, struts, piers, columns of any shape / cross section for fair finished surfaces of concrete complete all as specified and as directed.

Use and waste of form work to sides and soffits of floor or roof beams, beam haunchings, girders,bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floor and beam etc. for rough finished surfaces complete all as specified and as directed.

Use and waste of form work to sides of concrete foundation, footings, bases of column, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter; for rough finished surfaces complete all as specified and as directed.

Use and waste formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick [horizontal or sloping] including fair finished surfaces complete all as specified and directed.

S & F Factory made solid panel PVC door shutter 30 mm thick (style) manufactured as per SSR Part I specifications and drawing. consisting of frame made out of MS tubes for top & Bottom rails. MS frames shall be covered with heat moulded plain colour PVC "C" channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Paneling of plain colour PVC sheet to be fitted in the MS frame welded/ sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement manufactured as per SSR Part I specifications and drawings.

S&F PVC door frame size 50mm x 47mm made out of 5mm plain coloured PVC sheet reinforced with MS square tube supplying & fixing in opening as per specifications complete all as specified and as directed.

S & F Aluminium alloy, anodised, Sliding Door Bolt with hasp and staple [Bolt Type] of size 300 mm and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed.

S&F aluminium anodised, barrel tower bolts of extruded section with length of bolt 150 mm complete all as specified and as directed

S&F 100mm butt hinges extruded aluminium alloy with galvanised mild steel hinge pin, Type B-21 complete all as specified and directed.

S&F extruded aluminium alloy handles, fabricated type, anodised of size 150 mm complete all as specified and as directed.

S&F continuos (piano) hinges, mild steel bright finish or electrogalvanised, width of flaps 30 mm complete all as specified and as directed.

M&L for mild steel pipe 25 mm dia Drapery rod fancy type with PVC coating fixed in the MS hooks, and finials/ side brackets (both side), shade as approved by GE all as specified.

S&F aluminium hat & coat hooks solid body 125 mm to 175 mm fixed with brass screw complete all as specified and directed.

S&F 150 mm long floor door stopper of aluminium alloy body and tongue with hard drawn steel spring complete all as specified and directed.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staple/ wooden beads complete all as specified.

S & F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165

M & L for Rolled mild steel framed work conforming to Fe 410-W (Gde E-250) quality 'A' as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete drilled for fixing of steel gate sheeting or other covering, doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging also fastening and fixing complete all as specified.

S & F Mild steel (1mm Thickness), plain, blacksheet in wall cladding,steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required

S&F rolled mild steel sections as in main and cross beams, hip and jack rafters; purlins where connected to a common rafters, fixed with angle cleats or other connecting plates of Gde fe 410-W or E 250 (quality A) complete all as specified and as directed.

S&F rolled mild steel structural work in tubular trusses (frames), trussed, fixed with and including special shaped washer etc.complete using ERW or including butt welded tubes confirming to IS 1161-1998 complete all as specified and as directed.

S&F rolled mild steel plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or weleded attachement confirming to Fe- 290 (Gde E-165) complete all as specified and directed.

S & F MS machine made screw bolts with hexagonal or square head one end and screwed other or screwed both ends, fitted with washers and one hexagonal or square nut exceeding 22.50 cm and not exceeding 30 cm long, dia of neck exceeding 16 mm but not exceeding 20 mm complete all as specified and as directed.

S&F hand rails, half rounded or other stock section or core for wooden hand rail straight portion, drilled and counter sunk for balusters, nosing to steps including embeding in concrete and screwing etc wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire etc; flat iron fillets (for securing wire mesh etc,) including all necessary drilling bolting or riveting, etc and similar work conforming to Fe410-0 or Fe 310-0 complete all as specified and directed.

M&L for Mild Steel TMT steel bars of 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed.

S & F reinforcement using TMT steel bars of 5mm to 10mm dia bars as in stirrups, spacers and binders, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed.

S&F factory made steel windows with side hung shutter including box type hinges with steel handle and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

S&F factory made steel windows with side hung shutter including box type hinges with steel handle and steel peg stay, complete without glazing bars, dovetailed or welded complete all as specified and directed.

S&F steel ventilator with top hung shutter including hinges steel peg stay complete

M&L prepainted 0.50 mm thick gavalume aluminium zinc coating AZ 150 GI based corrugated steel coloured Sheet in profile pattern having tensile strength of 550 Mpa as in roof covering & on chajjas fixed with self tapping screws etc all as specified and directed

M&L Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.5mm thick of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws as specified

M&L for Providing water proofing treatment over cleaned roof surface with super thermo APP modified water proofing memberane comprising of the following for roofs:- (a) Cleaning of plastered roof surfaces and applying a coat of bitumen primer @ 0.30 kg/Sqm on top of dry surface of finished cement mortar plaster.

(b) One coat of hot blown bitumen of grade 85/25 @ 1.2kg /sqm shall be applied over primed surfaces.

(c) One layer of APP based polymeric water proofing membrane of weight not less than 3 kg/Sqm consisting 3mm thick reinforced with polyster non wove fabric shall be unrolled surfaces with lap of 100 mm and the over lap shall be sealed by flame.

(d) Applying two coats of aluminum paint on top of membrane @ 0.10Kg/Sqm complete all as specified and as directed..

M & L for 75mm thick, PCC 1:3:6, Type C-1, using 40mm graded aggregate as in Plinth protection etc surfaces finished even and smooth with out using extra cement complete all as specified and as directed

M & L for 25 mm thick, PCC 1:2:4, Type B-0, using 12.5mm graded aggregate as in Sub base for flooring complete all as specified and as directed.

M & L for 100 mm thick, PCC 1:4:8, Type D-2, using 40mm graded aggregate as in Sub base for flooring complete all as specified and as directed.

M&L Non skid coloured ceramic tiles 7 to 8mm thick square/ rectangular area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm as in floor etc set and jointed in neat cement slurry and pointed in white cement with pigment to match, laid over and including 15mm thick cement screed bed in cement mortar 1:6 complete all as specified and directed.

M&L for Vitriefied ceramic tiles 10mm thick of light shade (square/rectangular) polished area of each tiles not exceeding 0.36 sqm ove and including 20mm thick screed (1:6) bedding layer, set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tile complete all as specified.

All as described in serial item No 65 above but in skirting with rendering 10mm thick CM 1:4 complete all as specified and as directed.

M&L for glazed ceramic coloured tiles of size 450 x 300 x 6 to 7 mm, 450x350 or 350x250 6 to 7mm thick on vertical surfaces such as skirting/ dado etc. ,set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tile with & including rendering 10 mm thick cement plaster in cement mortar 1:4 finished rough to receive tiles complete all as specified and as directed.

M & L for 20 to 25 mm thick machine cut kota stone flooring laid over cement screed bed 20 mm thick bedding layer in cement mortar 1:6 and jointed with neat cement slurry mixed with pigment to match the shade of the slab and including rubbing and polishing complete all as specified and as directed.

M&L for 18 to 20 mm thick machine cut kota stone as in vertical surfaces, risers of steps, skirting, dado and pillars etc laid over and including 10 mm thick rendering in cement mortar 1:4, set and jointed in neat cement slurry and pointed with grey cement mixed with pigment to match the colour of stone slab and including rubbing and mirror polishing complete all as specified and as directed.

M & L for rendering 5 mm thick in Cement Mortar 1:3 on fair faces of concrete surfaces of ceiling surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M&L for 10mm thick rendering in cement mortar 1:6 on fair faces brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M&L 15mm thick rendering on concrete/brick surfaces in CM 1:4 mixed with water proofing compound as per manufactures instructions finished even and smooth without using extra cement complete all as specified . Note:- WPC shall be measured and paid saperately

M & L for rendering to brick / concrete surfaces, 15 mm thick in Cement Mortar 1:6, surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M&L for Prepration of old ceiling suraces includinng scrapping down smoke, soot, and efflorescent salts and treatings, oil and gresy spots, brooming down or steel wire brushing removing nails making good holes, cracks, etc on plastered or unplastered surfaces and applying one coat of white wash on ceiling surface complete all as specified and as directed.

M&L for Preparing Newly Plastered Surfaces of external Walls and applying Two Coats of Cement Base Paint over a coat of alkali resistant primer complete all as as specified and as directed.

M & L for preparing newly plastered wall surfaces and applying three coats of white wash complete all as specified and as directed.

M&L for preparation of newly plastered surfaces and applying three coat of white wash as in ceilling complete all as specified and as directed.

M&L for Preparing Newly Plastered Surfaces of internal wall and applying two Coats of oil emulsion distemper over and including 3 mm thick wall care putty on plastered wall surfaces complete all as specified and as directed.

Complete removal of existing treatment on walls by steel wire brushing and scraping etc and applying 3mm thick( Avg) Birla wall care putty in two layers on wall surfaces including rubbing, levelling and preparing the surfaces for receiving further finishes as specified and as directed.

S & F 3mm thick sheet glass ordinary quality and glazing with oil putty in squares not exceeding 0.5 Sq.m in each pane complete all as specified and as directed.

S&F 4mm thick figured glass, pin headed type and glazing with oil putty in square n. exc 0.5 sqm in each pane complete all as specified and as directed.

M&L for Prepration of old painted wooden surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint of white or tinted complete all as specified and as specified.

M&L for Preparation of new wooden surface of any description over 10 cm width or grith and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

M&L for painting to new steel surfaces of any description, over 10cm width or girth with two coats with synthetic enamel paint over a coat of red oxide primer including preparation of surfaces complete all as specified and directed.

M & L for two coats of synthetic enamel paint new / old steel surfaces not exceeding 10cm width or girth including preparation of surfaces complete all as specified and as directed.

S&F 15mm bore tubes medium grade galvanized with all fitting such as socket, elbow, Tee tee, union and short length etc. and fixed complete to walls and ceilings or laid in floors of any length all as specified and directed by Engr-in-charge.

S&F 20mm bore tubes medium grade galvanized with all fitting such as socket, elbow, Tee tee, union and short length etc. and fixed complete to walls and ceilings or laid in floors of any length all as specified and directed by Engr-in-charge.

S&F 25mm bore tubes medium grade galvanized with all fitting such as socket, elbow, Tee tee, union and short length etc. and fixed complete to walls and ceilings or laid in floors of any length all as specified and directed by Engr-in-charge.

M&L for 32 mm bore low density polythelene pipes (LDPE) with fittings of pressure rating 6 Kgf / Sqcm fixed to walls or in floors etc complete all as specified and as directed.

S& F 500 ltrs rotational moulded polythine water storage tanks (cylinder vertical with closed top) hoisted and fixed in position including ball brass valves, high pressure with polythene float and flynut complete screw for iron pipe or brass ferrule all as specified in SSR Part-I complete all as specified and as directed.

S & F 20mm bore ball valve high pressure PTMT with epoxy coated aluminium rod & high densitypolythene float ball and fly nut screwed for iron pipe complete all as specified.

S&F in repair Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guards and railing 600 mm long complete all as specified.Make- Jaquar Cat Part No- AKP 35715PS or equivalent as approved by GE.

S&F for Soap dish, stainless steel of size 160mm x 160mm x 90mm complete all as specified and as directed.

S&F, in repair, chromium plated, Toilet paper holder complete all as specified and directed. Make- Jaquar ACN-1151N, complete all as specified and as directed.

S & F in repairs Towel ring brass chromium plated round type fixed with screws and wooden or plastic cleats complete all as specified and directed.

S & F in repairs Towel rail 600 mm long and 20 mm dia brass chromium plated 'D' type fixed with screws and wooden or plastic cleats complete all as specified and as directed.

S&F in repair PVC connection pipe of 450 mm long, 15mm size with PTMT nuts complete all as specified and as directed.

Refixing old steel tubing and connections (15 mm bore pipe) in new or old position (Walls, ceiling, floors, etc.)

Refixing old steel tubing and connections (20 mm bore pipe) in new or old position (Walls, ceiling, floors, etc.)

Refixing old steel tubing and connections (25 mm or 32 mm bore pipe) in new or old position (Walls, eiling, floors, etc.)

S&F vitreous china wash down water closet pan Padestal pattern white excluding fixing bolts, flushing cistern and flush pipe with and incl 'P' or 'S' trap and making good to floor to match with existing all as specified and directed.

S & F in repairs Vitreous china ware wash hand basin, white, flat back of size 550 mm X 400 mm including brass chromium plated waste fittings with long screw shanks and fly nuts, flange end bedded in red led cement and other end fixed, rubber plug with rings including CI Brackets, cutting for and pinning in ends of brackets or erecting strand, 32mm bore PVC flexible waste pipe etc complete all as specified and as directed.

S&F CP waste fittings brass chromium plated for sink 32mm dia with long screws sinks and fly nuts , flenge end bedded in red led cement and other in fixed complete all as specified and as directed.

S&F CP waste fittings brass chromium plated for sink 40mm dia with long screws sinks and fly nuts , flenge end bedded in red led cement and other in fixed all as specified and directed.

S & F Vitreous china urinal half stall type ,white including connection to flushing pipe and outgoing pipe complete all as specified and directed.

S & F chromium plated Urinal spreader of any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) complete all as specified and as directed.

S&F PVC 10 litres capacity valveless ,syphonic action type low level flushing cistern ,white including flush pipe, cantilever brackets ,inlet, ball valve, float and handle, PVC connection 32mm dia, 450mm long etc complete all as specified and directed (Make: PRAYAG / CERA/ Parryware/Jaquar).

S& F in repairs chromium plated shower rose 125 mm size and 15mm dia with or without swivel joints including fixed to pipe or union complete all as specified and as directed

S&F in repair for 15mm chromium plated brass CP mixer for mixing hot and cold water screwed down for iron pipe and fixed complete all as specified and directed.

S&F in repairs fancy type wall mixture of brass, chromium plated, 3 in 1 system with hot and cold arrangement, with provision for both hand shower & overhead shower complete all as specified and as directed.

S&F in repair CP glass corner shelf set of three and including fixed CP Screws and CP brackets complete all as specified and as directed.

S& F in repairs 15 mm bore bib tap cast copper alloy, chromium plated, long body fancy type with capstan headed, screwed down, screwed for iron pipe complete all as specified and directed.

S& F in repairs Stop valve / Angle valve fancy type cast copper alloy chromium plated screwed down high pressure with capstan heads screwed both ends for iron pipe or for union and fixed 15mm bore complete all as specified and directed.

S&F 20mm dia gun metal, globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed complete all specified and directed

S&F 25mm dia gun metal, globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed complete all specified and directed

S&F in repairs grating doom 100mm dia PTMT with waste hole (Min weight 25 grms) complete all as specified and as directed.

S&F in repairs grating of doom 125mm dia PTMT with waste hole (Min weight 40 grms) complete all as specified and as directed.

S&F 15mm bore pillar taps cast copper alloy fancy type chromium plated screwed down high pressure with or without lattered HOT or COLD with long screwed shanks and fly nuts screwed for iron pipes, att as directed Engr-in-Charge.

S&F 110 mm dia PVC (SWR ) pipes Single socketed in any length with rubber ring jonits fixed to walls complete all as specified and as directed.

S&F PVC (SWR) pipes 75mm bore single socketed in any length with rubber ring joints laid in floors, trenches complete.

S&F 110 mm dia PVC (SWR) branch piece, double (double Y) equal or unequal with access door with rubber ring joints fixed to walls complete all as specified and as directed.

S&F PVC (SWR) branch pieces, single (equal or un equal) , ordinary or inverted (spigot or socket type) or with parralled branches of 110 mm dia with access door complete all as specified and as directed.

S&F 110 mm dia PVC (SWR) bends any radius with access door complete all as specified and as directed.

S&F 75 mm dia PVC (SWR ) bends any radius with access door complete all as specified and as directed.

S&F 110 mm bore PVC (SWR) vent cowl including jointing with solvent cement complete all as specified and directed.

M&L for 75mm dia PTMT multi floor trap plain with grating including jointing with solvent cement complete all as specified and as directed.

M&L for 100mm dia cast iron floor trap plain with grating including jointing and fixed with cement concrete type B-0 (1:2:4) complete all as specified and as directed.

M&L PVC (SWR) Tee of 110mm dia with access door etc complete all as specified anda as directed.

M&L PVC (SWR) Tee of 75mm dia with access door etc complete all as specified and directed

S&F PVC (SWR) gully trap 125 x 110 mm setting and jointing with solvent cement complete all as specified

S & F stack clamps out of 50mm by 5mm flat iron stays, including bolts and nuts and securing ends of stays to wall or roof for 100 mm bore etc all as specified.

M/L for Sub Main Wiring with two single core PVC insulated cable FRLSH of size 4.0 Sqmm multistranded copper conductor FRLSH cable drawing into and including concealed rigid non-metallic PVC conduit, medium grade not less than 20mm dia with all conduit fitting, fixing accessories and 4 Sqmm multistrand copper conductor FRLSH cable as continuous earth wire complete all as specified and as directed. Note :- Two Nos of 4.0 Sqmm Wire and One No of 4 Sqmm Earth wire in One RM length Measured as one unit length.

M&L for Point wiring with PVC insulated 1.5 sq mm multi stranded copper conductor FRLSH cable 1100 volts grade drawn into and including concealed PVC conduit not less than 20mm (ISI marked) including all fitting and fixing accessories including sunk in cast iron/pressed steel terminal boxes duly painted with two coats of anticorrosive paint outside and two coats of aluminium paint inside, 2.8mm thick hylam brand laminated white Bakelite sheet cover for mounting of switches, sockets, fan regulators etc and PVC insulated 1.5 Sqmm multistranded copper conductor FRLSH cable as earth wire and making good the disturbed surfaces to match with the existing surfaces complete all as specified and directed.

(a) One light point/Bell point controlled by one switch.

(b) One fan point controlled by one switch.

(c) One socket point controlled by one switch on same board.

(d) One socket point controlled by one switch on Independent board.

All as described in serial item No. 134 here-in-before, but with 1100 volts grade copper standard conductor FRLSH cable of size 2.5 Sqmm with 2.5 Sqmm solid copper conductor cable for 3 pin 15 Amp switch socket outlet independent board complete all as specified and directed.

S & F Switch piano flush type AC 230 volts 5 Amps single pole one way complete all as specified and directed.

S & F Socket outlet 3 pin, 5 Amps and AC 230 volts flush type complete all as specified and directed.

S & F switch socket combination 3 pin 5 and 16 Amps AC 230 volts flush type complete all as specified and as directed.

S & F Ceiling rose surface bakelite 65 mm x 50 mm three terminal AC 230 volts flush type complete all as specified and as directed.

Supply and fixing Single phase ceiling fan 1200 mm permanent magnet brushless DC Motor 230 v 50 Hz single phase 26-30watt rated current 0.16 amp,pf 0.98 370/360 rpm air delivery 220m3 rated service value 629m3/min/watt no of blades three type of blade leaf 1.05 mm thick aluminium sheet remote control radio frequency 5 speed +off timer option speed regulation class of insulation two nos bearings including connecting wire complete with all as required and directed at site by eng in charge Make : Havells/ CG/ Bajaj

Supply and fixing Single phase propeller type ventilating ( Exhaust fan) heavy duty AC 230 volts 300 mm sweep, metallic body complete with Metalic louvers including making holes of suitable size and making good the disturbed surface and shutters including electric connection with pvc flexible twin core copper wire from ceiling rose to Exhaust fan, nut & bolt complete all as specified and as directed.Make:Bajaj,havells or equivalent.

Supply & Fixing in repair sheet metal enclosure MCB DB double door [Acrylic], single pole and neutral, 240 volts, 8 way with 200 Amp, 10 KA breaking capacity rated bus bar with blanking plate wherever required and IP-43 degree protection complete all as specified & directed.Make : Legrand CAT NO 507611 / SIEMENS CAT NO 8 GB 32102RC8/GE

S & F for MCB Single pole and neutral rated capacity 40 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.Make : Legrand DX3 DP CAT No 408637/ Siemens cat no- 5SL 42327RC / GE

S & F for MCB Single pole rated capacity 5 to 40 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.Make : Legrand cat no DX3 SP 408587,408590,408592,408593,408594,408595 / Siemens cat no- 5SL41067RC, 5SL41107RC, 5SL41167RC, 5SL41207RC, 5SL41257RC, 5SL41327RC / GE

S&F in replacement of sheet steel enclouser distribution boards, double door factory made VTPN 4 way 3 phase 415 volts 4 way with 200 amps rating copper bus bar and PVC insulated copper jumpers of suitable size from the MCCB to the out going circuits one incoming MCCB 63 amps , circuits comprising of 3 phase 4 wire of suitable rating all as specified and directed.Make of Distribution Board Legrand cat no:5077 50 or equivalent in seimens /GE and Make of MCBs :Legrand/Seimens/GE

S & F MCB TPN 63 Amps, 240 Volts, minimum 10 KA, "C" series rupturing capacity and to be housed in DBs catered here in before complete all as specified and directed :-(Make- Legrand / L&T / Havells)(Note :- Proper and suitable size cablecopper lugs to be fixed with MCBs are included in unit rate of each MCB of any rating)

Supply & fix in replacement of LED Security Light Luminaire 25 watt 6000K with .high power LED cool white,CRI 75,+/- 5% supply voltage 220/240/50 Hz, light engine driver base.pole adapter,powder coated pressure die cast aluminium with heat resistant toughened glass with lens type,GI pipe 40 mm dia medium Grade not less than with 1.2 m.long in any shape with 2 nos of pole fitting clamps made out of MS flat , nuts and bolts and painting with aluminium paint. complete all as specified and as directed. Make:Havells cat part no: LHDAUU7PA7J025 or equivalent makes as mentioned here-in-after.

S&F in repairs Smart bright Batten Series, LED luminaire using LED 22 watt 110 Lumens/watt with diffuser which ensures uniform distribution and comfort, batten series features latest LEDs and delivers consistent light output, stable color start Extruded Aluminium housing, Energy efficient, Flicker free start Inbuilt driver unit, Suitable for wall and ceiling mounting using brackets with and including the luminaire testing on completion as per Standard Specification IEC 60598-2-1 / IS: 10322(Parts/Secl), (Make : Philips Cat part No BN 021 LED 22S 6500/4000 PSU GR S1 or equivalent makes as mentioned here-in-after.

Earthing complete with galvanised steel earth plate electrode 60 cm x60 cm x 6 mm thick buried directly in ground ,(Earth pit not less than 2.25 meter deep below ground level) with top edge of plate not less than 1.5 meter below normal ground level ,connected to and including galvanised iron earth wire 4 mm dia by means of nut, bolts, check nuts and washers of galvanised iron or steel complete all as specified and directed including testing on completion including the material and labour of the following : - (a) Excavation and earth work for drilling hole for electrode in any type of Soil. (b) PCC pit in cement concrete 1:2:4 type B-1, Pre cast RCC cover with suitable handle 40 mm thick in PCC 1:2:4 type B-1, reinforced with welded steel wire fabric weighing not less than1.87 Kg/ Sq meter. (c) Funnel with watering pipe of GI 20 mm nominal bore light grade and lugs etc complete all as specified and directed (d) 15 mm nominal bore medium grade GI protection pipe 5 meter long for protection of earthing lead complete all as specified and directed. (e) Requisite quantity of common salt and charcoal. (f) Testing of earthing.

Supply , laying and testsilng cable XLPE insulated , screened, PVC bedded , galvanized , steel strip or wire armoured, electric power cables ( Heavy duty ) 1100 volts grade with stranded aluminium conductor of size 4 core 25 Sqmm complete all as specified and directed by Engineer in charge

M & L for DWCP pipe 50 mm OD and 38 mm ID for cable protection with all acesseries all as per required and directed by Enggr in charge

Tiki Water proofing Co

ELITE ENGINEERING COMPANY

M/S RAJ BUILDERS

J.P ENTERPRISES

chandra builders

DEEPAK CONSTRUCTION