Emergent Rain Damage Repairing of Potholes of Symmetry Base Camp to Haptiagacch BOP Road from Ch. 0.00 Km to 4.00 Km (in stretches) under Uttar Dinajpur Highway Division in the District of Uttar Dinajpur.

Construction of embankment with approved material obtained from borrow pits (Earth available from Govt. land ) with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300-2 & 300-1 .The size course material in the mix of earth ordinarily shall not be exceed 75mm.(Reference to MoRT&H's specification clause 305). Cost of compensation for Earth material & its carriage from private land at 5km distance have been includedin the rate. [Note : Royalty will be deducted from the Agency's bill as per Govt. rules]

For Hard Shoulder By Mix in Place Method Construction of granular sub-base by providing graded materials such as natural sand/crushed gravel/crushed stone/(Pakur Variety)combination depending upon the required grading , spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator and compacting with vibratory roller to achieve at least 98% of the maximum dry density for the material determined as per IS:2720 (Part 8), complete as per clause 401 desired density, complete as per clause 401 Rate per cum for grading-II Material

Providing, laying, spreading and compacting stone aggregates (Pakur Variety) of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with 3 wheeled steel/ vibratory roller 8-10 tonnes in stages to proper grade and camber, applying and brooming requisite type of screening/ binding Materials to fill up the interstices of coarse aggregate, watering and compacting to the required density (Reference to MoRT&H's specification 404). By Manual Means Grading -2

Repairing Pot-holes with Bituminous Macadam (Grading - II, for compacted thickness of upto 75mm) Filling Pot Holes with Bituminous Macadam using Mobile Hot Mix plant (6-10 TPH) with approved crushed aggregates (Pakur Variety) of specified grading premixed with bituminous binder( VG- 30 (60/70) (Packed))@3.4% by wt. of the total mix, transported to site and laid in the pot hole prepared before hand by cutting the edges to get a firm vertical face and by removing all the failed and loose materials including dust and applying tack coat evenly on the sides and on the surface as per specification, rolling the filled depression with 8-10 tonne smooth wheeled roller to achieve the desired compaction, including the cost and carriage of stone aggregates and bitumen, hire charges of machinery and equipment, cost of fuel and lubricants and wages of all operational staff, quality control except the cost of tack coat complete as per direction of Engineer-in-charge. Payment to be made on the basis of the loose net volume of the stone aggregates used in the work.

Prime Coat Providing and applying primer coat with cationic bitumen emulsion SS1 grade conforming to IS:8887 on prepared porous granular surface including clearing of road surface and spraying primer using mechanical means (Reference to MORT&H's specification clause 502). On WMM/WBM surface @ 0.85kg /sqm. Using Bitumen Emulsion (Packed): CSS1 (H)

Tack Coat Providing and applying tack coat with Cationic bitumen emulsion (RS1) complying with IS:8887 using emulsion pressure distributor on the prepared bituminous/granular /cement concrete pavement surface cleaned with mechanical broom and high pressure air jet (Reference to MORT&H's specification clause 503). On bituminous surface @ 0.25kg /sqm Using Cationic RS

Tack Coat Providing and applying tack coat with Cationic bitumen emulsion (RS1) complying with IS:8887 using emulsion pressure distributor on the prepared bituminous/granular /cement concrete pavement surface cleaned with mechanical broom and high pressure air jet (Reference to MORT&H's specification clause 503). On Granular surface treated with primer @ 0.275 /sqm. Using Cationic RS

Filling Pot-holes and Patch Repairs with open-Graded Premix surfacing, 20mm. Removal of all failed material,in the pavement courses and if necessary below the pavement,until the root causes of the failure is removed, the trimming of completed excavation to provide firm vertical faces; specified for the pavement layer; application of tack coat conforming to cl. 503 of MORT&H's specification ,on to the sides and base of excavation prior to placing hot bituminous material as per clause 510 and the compaction,trimming and finishing of the surfaces of all patches to form a smooth continuous surface, level with the surrounding road as per the requirement of clause 3004.2 of MORT&H's specification .

Add GST @ 18%

Add Labour Welfare Cess @ 1%