Providing Fire Fighting System in Civil Hospital at Hisar.

Amount

[11.60]Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

[11.64.1]Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : 1. New work (two or more coats) over and including water thinnable priming coat with cement primer

[11.8.1]12 mm cement plaster of mix : 1. 1:4 (1 cement: 4 coarse sand)

[20.25.2]Cutting holes up to 23 cm square through brick work in mud walls for pipes and making good including repointing, replastering and finishing according to existing finish where required. 2. 22.86 cm thick wall

REPAIRING of Electrical motor driven fire pump suitable for automatic/ manual operation consisting of the following :- (i) - A) `Horizontal end suction single/ double stage centrifugal fire pump capable of delivering 2280 LPM against a total head of 70 m, 2900 RPM with multi spring mechanical seal, Phosphorous bronz impeller, wearing ring complete with connection to suction and delivery line, and includeing bypass aggangement for testing of pumps. Pump shall have a name plate indicating, head discharge, stages, RPM and direction of rotation.MAKE-KIRLOSKER B)) Pump shall be capable of handling not less than 150% of rated capacity at a head not less than 65 % of rated head. The shut off head shall not exceed 120% of rated head. HP of motor should be 20% more than the calculated HP. (ii) Squirrel cage, induction motor, TEFC type suitable for 415 plus 6%V, 3 phase, 50 Hz, AC supply, of suitable HP rating for the above pump with synchronous speed of 1450 RPM conforming to IP 55 protection and class `F` insulation. The motor shall conform to IS 325 1978(up to date) with flexible coupling and coupling guard. (iii) Epoxy coated common base plate for mounting pump and motor fabricated of mild steel channel as per manufacturer`s recommendation with required no. of heavy duty Anti Vibration pads. (iv) Flexible Coupling and coupling guard for direct coupling of pump and motor. (v) Drain Pipe (25 mm dia) (vi) Technical Parameter Main Hydrant and Sprinkler Pumps. :- A) Flow rate/Discharge : 2280 LPM B) Head - 70 m C) Motor HP - 60 HP (Approx.) or as per manufacturer recommendation vii) Material of construction A) Casing - CI B) Impeller - Phosphorous Bronze C) Shaft - SS 304 D) RPM - 2900 RPM E) Seal: Mechanical seal Note :- Rate should be inclusive of foundation bolts, viberation elimination peds. Item as Described above (NS ITEM)

Diesel Engine Driven Fire Pump : REPAIRING of Diesel Engine driven fire pump suitable for automatic/manual operations consisting of the following : (i) `Horizontal split case single/double stage centrifugal fire pump capable of delivering 2280 LPM against a total head of 70 M at 2150 RPM, Radiator Cooled Engine with two nos of 50 mm dia pressure reducing valves. complete with proper connection to suction and delivery line, and including bypass arrangement for testing of pumps, mechanical seal, drain, etc. Pump shall have a name plate indicating, head, discharge, stages, RPM and direction of rotation. (ii) Radiator Cooled Diesel engine of required BHP or as per manufacturer at 2150 RPM for the above pump complete with standard accessories and suitable cooling system two sets, pressure reducing valves, strainer, with bypass, etc. as described in specifications. (iii) Common base plate for mounting pump and engine of required strength manufactured out of M.S. channels as per manufacture`s recommendation with required no. of heavy duty Anti Vibration pads. (iv) Flexible Coupling and coupling guard for direct coupling of engine and pump. (v) Suitable For Installation on reinforced cement concrete pump foundations as per manufacturer design including foundation bolts, washer as required. (vi) 1 No. 6 hours capacity day oil storage tank (Minimum 200 Ltr) of welded steel construction Tank shall be provided with inlet, outlet, overflow, air vent, drain connections, filling connection and magnetic level indicator showing the level of fuel in the tank. Tank shall be mounted on a suitable mild steel structure (Painted with 2 coats of red oxide paint). Tank shall be provided with epoxy coat from inside and two or more coats of synthetic enamel paint outside over two coats of red oxide primer. Diesel storage tank shall be double skin. (vii) 24 volts 160 AH lead acid battery (12 volts - 2 Nos) with boost/Trickle charger for starting the engine automatically complete as required. (viii) Technical Parameter of Diesel Engine driven pump: (a) Flow rate/Discharge : 2280 LPM (b) Head - 70 m ( c ) Engine BHP - 104 or as per manufacturers. (ix) Material of construction (a) Casing - CI (b) Shaft - SS 304 (c) RPM - 1450 RPM (d) Seat mechanical seal (x) Rate should include foundation bolts, vibration elimination pads, etc complete. MOTOR-60 H.P Item as Described above :: BRONZE IMPELLER (NS ITEM)

Providing, fixing, testing and commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories : (DSR CODE NO - 21.2) Upright Sprinkler

Supply Installation and Testing of Carbon-di-oxide type fire extinguishers consisting of welded M.S. cylindrical body, internal discharge tube, discharge nozzle, suspension bracket, conforming to IS 15683, finished externally with red enamel paint and fixed to wall with brackets complete with internal charges a) Capacity 4.5 kg NS

Supply Installation and Testing of stored pressure vessel ABC Powder type fire extingushers consisting of seamless cylindrical body, squeeze lever dischange valve fitted with pressure indicating guage internal discharge tube, 30 cms long high pressure discharge hose, discharge nozzle, suspension bracket, conforming to IS : 15683 finished externally with red enamel paint and fixed to wall with brackets complete with internal charge. a) Capacity 6 Kg. NS

Providing, laying, testing and commissioning of `C` class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :(DSR CODE NO. 7) DSR 7.1 25 mm nominal bore

Providing, laying, testing and commissioning of `C` class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :(DSR CODE NO. 7) DSR 7.4 50 mm nominal bore

Providing, laying, testing and commissioning of `C` class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :(DSR CODE NO. 7) DSR 7.5 65 mm nominal bore

Providing, laying, testing and commissioning of `C` class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :(DSR CODE NO. 7) DSR 7.6 80 mm nominal bore

Providing, laying, testing and commissioning of `C` class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :(DSR CODE NO. 7) DSR 7.7 100 mm nominal bore

Providing, laying, testing and commissioning of `C` class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :(DSR CODE NO. 7) DSR 7.8 150 mm nominal bore

Supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Jockey Pump) Horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS : 1520. Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase 50 Hz AC supply with IP 55 class of protection for enclosure, horizontal foot mounted type with Class-`F` insulation,conforming to IS : 325. M.S.fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered and with anti vibration pads. 180 lpm at 88 m Head (DSR item no. 3.1)

Providing and Fixing Cast Iron butterfly valve as per IS: 13095 of Class PN 1.6, having epoxy coated disc, carbon steel shaft, EPDM rubber body liner and of approved make. including a set of MS flanges, required nos. of nut and bolts all complete. Kartar Make :: 80 mm dia DSR CODE NO. - 11.4

Providing and Fixing Cast Iron butterfly valve as per IS: 13095 of Class PN 1.6, having epoxy coated disc, carbon steel shaft, EPDM rubber body liner and of approved make. including a set of MS flanges, required nos. of nut and bolts all complete. Kartar Make :: 65 mm dia DSR CODE NO. - 11.3

Providing and Fixing Cast Iron butterfly valve as per IS: 13095 of Class PN 16, having epoxy coated disc, carbon steel shaft, EPDM rubber body liner and of approved make. including a set of MS flanges, required nos. of nut and bolts all complete. Kartar Make :: 50mm dia DSR CODE NO. - 11.2

Providing and Fixing Cast Iron butterfly valve as per IS: 13095 of Class PN 16, having epoxy coated disc, carbon steel shaft, EPDM rubber body liner and of approved make. including a set of MS flanges, required nos. of nut and bolts all complete. Kartar Make :: 40 mm dia DSR CODE NO. - 11.1

Supply and Fixing of Glow Type EXIT Sign Board photo luminescent of size 300 mm x 250 mm x 1.5 mm rigid sheet signage containing Zink sulphate as bare chemical class 1 material PSPA fixed on 3mm acrylic sheet on both side showing marking (running man, Arrow and Exit) and hanged with the ceiling with chain and fastener including cost of labour and material required to complete the job in all respect