PROVN OF 4 x TOILETS AND BATHROOM FOR JCOs AND SPL REPAIR TO SQUASH COURT FLOORING INCLUDING CERTAIN REVENUE WORKS AT DINJAN MIL STN UNDER GE DINJAN

Amount

Surface dressing in soft/loose sooil not exceeding 15cm deep and getting out complete all as specified and as directed.

Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in soft/loose complete all as specified and as directed.

M&L for excavation in post holes (or similar holes) in soft/loose soil, each not exc 0.5cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm complete all as specified and as directed.

Excavating in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth, for foundation etc. or for shafts, wells, cesspits ,manholes, pier holes etc not exceeding 10Sqm on plan and not exceeding 1.5m in depth and getting out soft/ loose soil complete all as specified and as directed.

Returning filling in including spreading levelling, watering and wall ramming in layers not exc 25cm complete all as specified and as directed.

Removing excavated material soil n.exc 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as directed.

M&L for cement concrete type D-2, 1:4:8 (using 40mm graded aggregate) in foundations, filling and mass concrete complete all as specified and as directed.

M&L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work vertical or to batter rough finished surfaces of concrete flat complete all as specified and as directed.

M&L for formwork to sides of pillars, posts, struts, piers, columns and stanchions rough finished surfaces of concrete square, rectangulr or polygonal complete all as specified and as directed.

M&L for formwork to soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs etc also splays between floors and beams etc. rough finished flat surfaces complete all as specified and as directed.

M&L for RCC (design mix) M-25 (using 20mm graded aggregates) in foundations, incl rafts ,footings, foundation beams, plinth beams, bases for columns etc. basement slabs ,under reamed piles and mass concrete complete all as specified and as directed.

M&L for RCC (design mix) M-25 (using 20mm graded aggregates) in Columns, pillars, piers, posts and struts complete all as specified and as directed.

M&L for RCC (design mix) M-25 (using 20mm graded aggregates) in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed.

M/L for brick work with subclass 'B' bricks, straight or curved on plan exceeding 6m mean radius built in cement mortar (1:4) complete all as specified and as directed.

M&L for DPC to horizontal or vertical surfaces including necessary formwork in cement concrete 1:2:4, type B-1, 40mm thick complete all as specified and as directed.

M&L for TMT bars 10 mm dia and over ,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and as directed.

M&L for TMT bars 5mm dia and over upto and incl 10mm dia in stirrups, spacers and binders,cut to length, bent to shape required, incl cranking, bending spirally for hooping for columns, hooking ends and binding with and incl mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and as directed.

M&L for glazed colour ceramic tiles in vertical surfaces 450x350x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over 10mm thick rendering in cement mortar (1:4) as a backing coat complete all as specified and as directed.

M&L for coloured non skid ceramic tile 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06sqm but not exceeding 0.11 sqm, in floors etc set & jointed in neat cement slurry and pointed in white or coloured cement to match,including 15mm thick screed bed in cement mortar (1:6) complete all as specified and as directed.

M&L for granite (of any type) work (table rubbled and polished) in steps, Jambs, Pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed

M&L for machine cut cudappa stone slab 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete including 15mm thick screed bed in cement mortar (1:6) complete all as specified and as directed.

S&F in repairs white vitreous china squatting pan orissa pattern of size 580mm x 440 mm, with integral foot rest and P or S trap connection to trap and to flushing pipe front or back inlet including, trap etc. complete all as specified and as directed.

S&F for 110mm PVC (SWR) WC connector with lip ring complete all as specified and as directed.

S&F for 10 litre capacity PVC valveless, syphonic action type flushing cistern, low level, white, with intel, ball valve, float and handle including brackets complete all as specified and as drected.

S&F in repairs towel rails 60 cm long brass chromium plated 20mm dia with brackets fixed to walls complete all as specified and as directed.

S&F for soap dish vitreous china coloured approximate size (160mmx160mmx90mm) complete all as specified and as directed.

S&F for stop valves, cast copper alloy 20mm bore screwed down high pressure with crutch or butter fly handle screwed both ends for iron pipe or for union and complete all as specified and as directed.

S&F for stop valves, fancy type chromium plated with long sunk and cup (concealed type) screwed down high pressure with crutch or butter fly handle screwed both ends for iron pipe or for union and complete all as specified and as directed.

S&F PVC connections 15mm size with PTMT nuts, 600mm long complete all as specified and as directed.

S&F for high density polythylene pipe (HDPE) of pressure rating 6 kgf/Sqcm fixed complete to walls ceiling or in floors etc bore of pipe 32mm complete all as specified and as directed.

S&F for bib taps cast copper alloy, fancy type CP with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferule and fixed of size 15mm bore complete all as specified and as directed.

S&F for 16mm of CPVC pipes SDR 11& Plain CPVC SDR 11 fittings in tranches complete all as specified and as directed.

S&F for 20mm of CPVC pipes SDR 11& Plain CPVC SDR 11 fittings in tranches complete all as specified and as directed.

S&F for 16mm dia CPVC brass thread elbow complete all as specified and as directed.

S&F for 16mm dia CPVC Brass thread Tee complete all as specified and as directed.

S&F 20 mm CPVC brass thread union complete all as specified and as directed.

S&F for 16 mm CPVC Brass thread union omplete all as specified and as directed.

S&F for 20mm dia CPVC Brass thread elbow omplete all as specified and as directed.

S&F for 20mm dia CPVC Brass thread Tee omplete all as specified and as directed.

S&F for 20mm CPVC Brass thread union complete all as specified and as directed.

M&L for compound girders and stanchions, lattice girders, aerial masts, staging for water tanks and the like including caps, bases, splices etc. built up from two or more beam or channel sections or angles with plates, including all lattice bars, stiffeners, gusset plates, etc Fe-290 (Gde E-165) complete all as specified and as directed.

S&F for rotational moulded polythylene 500 litre water storage tank (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part -I (2000 Ltrs) capacit complete all as specified and as directed.

M&L for rendering 15mm thick in cement mortar (1:6) on fair faces of stone or concrete surfaces etc, finished even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 15mm thick in cement mortar (1:4) on fair faces of stone or concrete surfaces etc, finished even and smooth without using extra cement complete all as specified and as directed.

M&L for preparation of new plastered surface of external walls and applying two coats of cement base paint over a coat of alkali resistant primer complete all as specified and as directed.

M&L for three coat of white wash and including preparation of surfaces of new wall complete all as specified and as directed.

S&F for PVC SWR floor trap plain with grating including jointing with solvent cement, dia of outer 75mm complete all as specified and as directed.

S&F for PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches ,in floors or wall of 110 mm dia as in sewage line complete all as specified and as directed.

S&F for 110mm PVC Vent cowl complete all as specified and as directed

S&F for 32mm Brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed complete all as specified and as directed.

M&L for cement concrete (1:3:6) type D-2 (using 40mm graded aggregate) as in bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested in for 110mm dia pipe complete all as specified and as directed.

S&F for 75mm bore PVC Pipes single socketed , in any length with rubber ring joints, fixed to walls complete all as specified and as directed.

S&F for 75mm PVC (SWR) bends any radius complete all as specified and as directed.

S&F for 110mm PVC (SWR) bends any radius complete all as specified and as directed.

S&F for 110 mm bore PVC (SWR) bends with access door any radius complete all as specified and as directed.

S&F for PVC (SWR) gully trap 125/110mm setting and jointing with solvent cement complete all as specified and as directed.

S&F for 15mm dia angle stop cock with wall flange complete all as specified and as directed. Make : Cat No. G1453A1 of Parryware/Jaquar/Cera.

S&F for wall mixer 2-in-1 complete all as specified and as directed. Make : Cat No. G1416A1 of Parryware/Jaquar/Cera.

S&F sqan neck pillar cock complete all as specified and as directed. Make : Cat No. G1468A1 of Parryware/Jaquar/Cera.

S&F Towel Ring complete all as specified and as directed. Make : Cat No. T-6502A1 of Parryware/Jaquar/Cera.

S&F Corner self complete all as specified and as directed. Make : Cat No. T6010A1 of Parryware/Jaquar/Cera.

S&F Cascade NXT below counter basin white complete all as specified and as directed. Make : Cat No. C0407 of Parryware/Jaquar/Cera.

S&F counter top basin size 550x445x200mm white colour complete all as specified and as directed. (Make: Cat No. C0431 of Parryware/Jaquar/Cera.

S&F for solid PVC door frames of size 50mm x 47 mm made out of 5 mm thick plain/printed coloured PVC sheet reinforced with MS square tube all as per specification & drg in SSR Pt II 2004 complete all as specified and as directed.

S&F for factory made solid panel PVC door shutter 30mm thick (styles) consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded plain colour PVC Channel having a PVC sheet strip of 20mm width stuck inside with solvent cementfor styles & plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitten in the MS frame welded/sealed to the styles & rails with suitable PVC sheet beading & jointed together with solvent cement, complete all as specified and shown in drgs in SSR Pt II 2004.

S&F aluminium anodised barrel tower bolts of extruded section 150 mm long complete all as specified and as directed.

S&F for 100mm butt hinges, heavy weight, cold rolled mild steel complete all as specified and as directed.

S&F for aluminium handle cast type, anodised 150mm long extruded fabricated type complete all as specified and as directed.

M&L for hangers 6 mm dia. G.I. (up to 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of galvanised iron flat 40x3mm size 60mm long, grid 605mmx605mm complete all as specified and as directed.

S&F for Anodised aluminium snap grid frame work for false ceiling complete all as specified and as directed.

M&L for 4mm thick Non asbestos fibre cement building boards fixed or laid/ inserted to timber/GI/Aluminium framework with screws complete all as specified and as directed.

M&L for three coat of white wash and including preparation of surfaces of ceiling complete all as specified and as directed.

S&F in repair 125mm size brass chromium plated shower rose with or without arm complete all as specified and as directed.

S&F for roof trusses (framed), trussed, purlins, crane, gantries, rails and fastenings and heavy bracket, framing, (beam, tee, angle, channel or flat sections, including distance pieces, cleats etc. Fe-290 (Gde E-165) complete all as specified and as directed.

S&F for pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F for pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

M&L for preparation of newely steel surfaces and applying two coat of synthetic enamel paint over one coat of red oxide zinc chrome surfaces of any descriptionh, over 10cm in widyh or girth not other wise described complete all as specified and as directed.

S&F for anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and as directed.

S&F for anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified and as directed.

S&F for sheet glass ordinary quality 3mm thick and glazed with oil putty or fixed with beads in square n.exc 0.5 Sqm in each pane complete all as specified and as directed.

S&F for galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tracks, or galvanised wire staples complete all as specified and as directed.

M&L for "Ricochet" squash court wooden flooring system 21mm Maple wood flooring 62.40Sqmt 10.19mm Mrubber 70*45mm Pine rubber including termite treatment of entire floor and wall of court complete all as specified and as directed.

S&F for vitreous china wash hand basin white flat back size 550x400mm excluding taps, waste chain and plug and porcelain stopper including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe complete all as specified and as directed.

S&F for pillar taps, chromium plated fancy type cast copper alloy, with capstan heads, screwed down high pressure, with or without lettered 'Hot' or cold with long screwed shanks and fly nuts screwed for iron pipe of bore 15mm complete all as specified and as directed.

S&F in repairs for vitreous china bowl urinal flat back, size of 465x355x265mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) but fixing plug bedding urinal against wall in cement mortar 1:2 securing urinal to plug with and including 60mm long brass screws pointing around urinal back in cement mortar including 15mm brass stop cock and waste coupling brass CP complete all as specified and as directed.

M&L for broken bricks hardcore of guage n exc. 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and as directed.

M&L for 100mm thick PCC (1:4:8) type D-2 (using 40mm graded stone aggregate) as in sub base for floor etc. complete all as specified and as directed.

M&L for 40mm thick PCC (1:2:4) type B-1 (using 20mm graded stone aggregate) as in floor etc. complete all as specified and as directed.

M&L for 38mm wide aluminium dividing strips, 1.5mm thick, inserted in position, confirm to design complete all as specified and as directed.

S&F for steel work in tubular truses including special shaped washer etc. complete using ERW or inductionbut welded tubes conforming to IS 1161-1979 grade St-240 complete all as specified and as directed.

S&F for mild steel screw bolts (Machine made) 11 to 15mm dia of neck, with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, not exc 5cm long complete all as specified and as directed.

M&L for concealed point wiring with 1.5 sq mm (nominal area) single core pvc insulated FR unsheathed multi-standared copper conductor cable (maintaining colour code), 1100 volt grade and including pvc conduitct (size as required site) concealed and sunken terminal boxes with 3 mm hylam sheet top cover of adequate size for mounting switches , sockets , regulators light fitting etc complete with all fitting and accessories fixed to wall /ceiling for one light /fan/call bell point concealed by one switch including one run 1.5 sq mm (nominal area) PVC insulated frame retardant unsheathed multistranded copper conductor cable green in colour for earth continuity conductor connected to common earth point duly completed all as specified and directed.

S&F for switch piano, flush type single pole, one way 5 Amp complete all as specified and as directed.

S&F for ceiling rose, 3 way PVC insulated body complete all as specified and as directed.

S&F for 18 W surface and wall mounted LED Batten with polycarbonate housing and intigrated. Make : Cat No. LUMILINEBS18WLED865SPCWH of Havells/ Philips/Bajaj/CG/Wipro.

M&L for lamp holder, PVC/polycarbonate type with black plate suitable for batten fittings complete all as specified and as directed.

S&F for LED Lamp 7 Watt complete all as specified and as directed. Make : Havells/Philips/Bajaj.

S&F for 25 W LED building security new generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminum housing with hight power LED as lighting source and lens imbedded PC Cover having TOP OPENING seperate driver cmpartment with IP 65 protection and inpact resistance of IK07 including with necessary clamps/pipe/nut bolts for holding the building security light complete all as specified and as directed. Make : Cat No. ENDURAPEARLSL25WLED757SASYTOPC of Havells/Philips/Bajaj/ CG/Wipro.

S&F for exhaust fans AC single phase 230/ 240 V of size 380 mm sweep 1 phase 1400 RPM including LOUVER SHUTTER of suitable size complete all as specified and as directed. Make : Cat No. EXHD380-4-1 Crompton Greaves/Bajaj/Havells.

S&F for sheet metal enclosure for MCB DB double door single pole and neutral 4 way, 240 V with common bus bar at incomming and complete all as specified and as directed.

S&F for MCB 'C' curve Single pole & Neutral 6 to 32 Amps with breaking capacity 10 kA complete all as specified and as directed. Make : Cat No. 408609-17 of Legrand/L&T/HPL.

S&F for MCB 'C' series SP 6 to 32 Amps, 240 volts, breaking capacity 10KA complete all as specified and as directed. Make: Cat No. 4086 09-17 of Legrand/L&T/HPL.

M&L for earthing complete with galvanized steel earth plate electrode 600x600x6 mm thick buried directly in ground (earth pit not less than 2.25 m deep below normal ground level) with top edge of the plate not less than 1.5 m below normal ground level connected to 4.0mm GI wire by means of bolts and nuts checknuts and washers of galvanized iron or steel all as specified and shown in electrical plate no 3 of SSR part I including necessary excavation and earth work in any type of soil PCC 1:3:6 type C1 chamber with RCC 1:2:4 type B1 40 mm thick cover with MS rod 8mm dia 150mm long reinforcement, watering funnel, 40 mm dia light grade for protection of earth electrode 20 mm dia for watering complete all as specified and as directed and tested on completion.

Supply and spreading clean dry sand in trenches for cushioning all as specified for cable protection complete as specified.

Supply and lay bricks of class 'B' type for protection of under ground cable in trends complete all as specified and as directed.

M&L for XLPE insulated, armoured heavy duty electric cable with aluminium conductor 1100 volts grade, cross section area 10Sqmm and 2 core complete all as specified and as directed.

S&F galvanized steel tubing light grade, with fittings and mild steel clamps nut, bolts etc of 32mm dia bore for cable protection on pole, road crossing or ground in pillar for fixing light etc complete all as specified and as directed.

Supply and laying and jointing galvanished steel water tubing of size 25 m bore medium grade including galvanised iron fititngs such as bends, tees, sockets, nipples and unions, flanges etc. and connecting complete all as specified and as directed.

S&F for 25mm gun metal gate valve with iron wheel head, screwed both ends for iron pipe complete all as specified and as directed.

Kaushik Enterprises

NChetia and Sons Trading

Bimal Trading Company

M/s GANDHESWAR PHUKAN

FREEZCON

STANDARD ELECTRIC WINDERS