Improvements to Type III, J-block 6Units at Government Servant Quarters Lawspet, Puducherry.

Amount

Earthwork in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5m, including getting out the excavated soil and disposal of surplus excavated soil as directed , within a lead of 50m - all kinds of soil

Supplying chemical emulsion in sealed containers including delivery as specified - Chlorpyriphos / lindane emulsifiable concentrate of 20%

Diluting and injecting chemical emulsion for POST - CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) - along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. - with chlorpyriphosl lindane E.C.20% with 1% concentration.

Diluting and injecting chemical emulsion for POST - CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) - tratment of soil under existing flooors using chemical emulsion @ one litre per hole, 300mm apart including drilling 12mm diametre holes and plugging with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floor - with Chlorpyriphos / lindane E.C. 20% with 1% concentration -

Diluting and injecting chemical emulsion for POST - CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) - Treatment of existing masonry using chemical emulsion @ one litre per hole at 300mm interval including drilling holes at 45 degree and plugging them with cement mortar 1:2 ( 1 cement : 2 coarse sand) to the full depth of the hole - with chlorpyriphos / lindane E.C. 20% with 1% concentration

Diluting and injecting chemical emulsion for POST - CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) - treatment at points of contact of wood work by chemical emulsion Chlorpyriphos / Lindane ( in oil or kerosene based solution) @ 0.5 litres per hole by drilling 6mm dia holes at downward angle of 45 degree at 150mm centre to centre and sealing the same

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plith level - 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40mm nominal size)

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns,piers, abutments, pillars, posts,struts, buttresses, string or lacing courses, parapets, coping,bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc. upto floor five level, excluding the cost of centering ,shuttering and finishing - 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)

Providing and fixing upto floor five level precast cement concrete string or lacing courses , copings, bed plates, anchor blocks, plain window sills, shelves , louvers, steps, stair cases, etc. including hoisting and setting in position with cement mortar 1:3 (1 cement : 3 coarse sand), cost of required centering , shuttering complete - 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size)

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement :2 coarse sand : 4 graded stone aggregate 20mm nominal size)

Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacture's specification.

Steel reinforcement for R.C.C.work including straightening , cutting , bending, placing in position and binding all complete upto plinth level - Thermo -Mechanically treated bars (ISI BRAND OF APPROVED MAKE) Fe- 415 or more

Reinforced cement concrete work in beams, suspended floors , roofs having slope up to 15degree landings , balconies , shelves , chajjas , lintels , bands , plain window sills , staircases and spiral stair cases upto floor five level excluing the cost of centering ,shuttering, finishing and reinforcement , with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)

Centering and shuttering including strutting , propping etc and removal of form for -Weather shade , Chajjas, corbels etc., including edges

Brick work with common burnt clay F.P.S. (non modular ) bricks of class designation 3.5 in foundation and plinth in - cement mortar 1:4 (1 cement : 4 coarse sand)

Brick work with common burnt clay F.P.S (non modular ) bricks of class designation 3.5 in superstructure above plinth level upto floor five level in all shapes and sizes in - cement mortar 1:6 ( 1 cement : 6 coarse sand)

Providing wood work in frames of doors ,windows, clerestory windows and other frames , wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately) -Vengai wood

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part 1) non - decorative type, core of block board construction with frame of 1 st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters - 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Extra for providing lipping with teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured)

Extra for cutting rebate in flush door shutters (Total area of the shutter to be measured)

Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc.complete - 100 x 58 x 1.90 mm

Providing and fixing aluminium sliding door bolts , ISI marked , anodised ( anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade , with nuts and screws etc complete - 300 X 16 mm

Providing and fixing aluminium tower bolts , ISI marked , anodised (anodic coating not less than grade AC 10 as per IS :1868) , transparent or dyed to required colour or shade , with necessary screws etc. complete - 300 x10 mm

Providing and fixing aluminium handles , ISI marked , anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade,with necessary screws etc, complete - 125 mm

Providing and fixing aluminium hanging floor door stopper , ISI marked , anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc complete - Twin rubber stopper

Providing and fixing bright finished brass 100 mm mortice latch and lock , ISI marked , with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) aluminium lever handles of approved quality with necessary screws etc complete

Providing and fixing magnetic catcher of approved quality in cupboard / ward robe shutters , including fixing with necessary screws etc complete - Triple strip vertical type

Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance +_ 1mm ), with wall thickness 2.0 mm (+-0.2mm) , corners of the door frame to be jointed with galvanized brackets and stainless steel screws , joints mitred and plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S.tube of size 19 x 19 mm and 1mm (+-0.1mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer's specification - Extruded section profile size 42 x 50 mm

Providing and fixing to existing door frames - 24 mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section of size 59 x 24 mm and wall thickness 2 mm (+- 0.2 mm) with inbuilt edging on both sides . The styles and rails mitred and joint at the corners by means of M.S. galvanised / plastic brackets of size 75 x 220 mm having wall thickness 1.0 mm and stainless steel screws . The styles of the shutter reinforced by inserting galvanised M.S.tube of size 20x20 mm and 1mm (+- 0.1mm) wall thickness . The lock rail made up of 'H' section , a uPVC hollow section of size 100 x 24 mm and 2 mm (+-0.2 mm) wall thickness , fixed to the shutter styles by means of plastic / galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multichambered single panel of size not less than 620 mm, having overall thickness of 20 mm and 1 mm (+_ 0.1mm) wall thickness . They panels filled vertcally and tie bar at two places by inserting horizontally 6 mm galvanised M.S.rod and fastened with nuts and washers , complete as per manufacturer's specification (For W.C. and bathroom door shutter)

Providing and fixing PVC rigid foam sheet 1 mm thick on existing door shutters (bathroom and W.C . Doors) using synthetic rubber based adhesive

Providing and fixing cup board shutters with 25 mm thick veneered particle board IS : 3097 marked , exterior grade (Grade 1) , of approved make including teak wood lipping of 25 mm wide x 12 mm thick with necessary screws and bright finished stainless steel piano hinges , complete - with decorative veneering on one side and commercial veneering on other side

Providing and fixing factory made uPVC white colour fixed glazed windows / ventilators comprising of uPVC multi - chambered frame and mullion (where ever required ) extruded profiles duly reinforced with 1.6 + or - 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension , EPDM gasket, G.I.fastners 100 x 8 mm size for fixing frame to finished wall , plastic packers , plastic caps and necessary stainless steel screws etc.Profile of frame shall be mitred cut and fusion welded at all corners , mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality , all complete as per approved drawing. (Single / double glass panes and silicon sealant shall be paid separately) - Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 + or - 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm) - Fixed window size - 1.20x0.50 m

Steel work welded in built up sections /framed work , including cutting,hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required - in gratings, frames, guard bar, ladder, railings, brackets,gates and similar works

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc .complete - 40mm thick with 20mm nominal size stone aggregate

Providing and laying pressed clay tiles (as per approved pattern 18mm nominal thickness of approved size) on roofs jointed with cement mortar 1:4 (1 cement : 4 coarse sand) mixed with 2% integral water proofing compound , laid over a bed of 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) and finished neat complete

Making khurras 45x45cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20mm nominal size) over P.V.C. sheet 1m x1m x 400 micron , finished with 12 mm cement plaster 1:3 ( 1cement : 3 coarse sand) and a coat of neat cement , rounding the edges, making and finishing the outlet complete.

Providing and fixing on wall face unplasticised rigid PVC rain water pipes conforming to IS: 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10mm gap for thermal expansion, (i) Single socketed pipes - 110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings / accessories for unplasticised rigid PVC rain water pipes conforming to IS:13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10mm gap for thermal expansion - Single tee with door - 110x110x110mm

Providing and fixing on wall face unplasticised - PVC moulded fittings / accessories for unplasticised rigid PVC rain water pipes conforming to IS:13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10mm gap for thermal expansion - shoe (plain) - 110mm shoe

Providing and fixing unplasticised - PVC pipe clips of approved design to unplasticised- PVC rain water pipes by means of 50x50x50mm hard wood plugs , screwed with M.S. screws of required length, including cutting brickwork and fixing in cement mortar 1:4 ( 1 cement : 4 coarse sand) and making good the wall etc., complete - 110mm

15mm cement plaster on the rough side of single or half brick wall of mix - 1:6 (1cement : 6 fine sand)

6mm cement plaster of mix 1:3 (1 cement : 3 fine sand)

Applying one coat of water thinnable cement primer of approved brand and manufacturer on wall surface - water thinnable cement primer

Finishing with deluxe multi surface paint system for interiors and exteriors using primer as per manufacture's specification - Two or more coats applied on walls @1.25 ltr / 10 sqm over and including one coat of special primer applied @ 0.75 ltr / 10 sqm

Painting with synthetic enamel paint of approved brand and manufacutre to give an even shade - Two or more coats on new work

French spirit polishing - Two or more coats on new works including a coat of wood filler

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scrarches etc.complete

Finishing walls with premium acrylic smooth exterior paint with silicon additives of required shade - old work (two or more coats applied @ 1.43 ltr / 10 sqm) over existing cement paint surface

Providing and fixing double scaffolding system (cup lock type) on the exterior side, upto seven story hight made with 40 mm dia .M.S.tube 1.5m centre to centre , horizontal & vertical tubes joining with cup & lock system with M.S.tubes, M.S.tube challies, M.S.clamps and M.S.staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after. The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required locations with essential safety features for the workmen etc.complete as approved. The elevational area of the scaffolding shall be measured for payment purpose. The payment will be made once irrespective of duration of scaffolding. (Note: This item to be used for maintenance work judicically, necessary deduction for scaffolding in the existing item to be done.)

Demolishing lime concrete manually / by mechanical means and disposal of material within 50 metres

Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead - nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Demolishing brick work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead - in cement mortar

Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead - of area 3 sqm and below

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead - for thickness of tiles above 25 mm and upto 40 mm

Providing and laying 60mm thick factory made cement concrete interlocking paver block of M-30 grade made by block making machine with strong vibratory compaction and of approved size and design / shape laid in required colour and pattern over and including 50mm thick compacted bed of course sand , filling the joints with coarse sand etc. all complte

Providing and fixing G.I.chain link fabric fencing of required width in mesh size 50 x50 mm including strengthening with 2mm dia wire or nuts , bolts and washers as required complete - Made of G.I.wire of dia 4mm , PVC coated to achieve outer dia not less than 5mm in required colour and shade

Acid cleaning for the existing Mosaic floors , glazed tiles work and removing the stains and decays to give a glassy look etc complte (The Acid used shall be 32% concentrated hydrochloric acid after taking on the precautionary measures)

Supply and fixing of sliding windows at all levels made out from Unplasticised Poly vinyl chloride frame (UPVC) of natural colour (PRISTINE WHITE) with outer frame of size 40 x 56x40mm / 102 x 56x 40mm and for shutter frame of size 53 x 38 x37 mm for two track / three track sliding widows , with wall thickness of 1.8mm (+/-0.3mm). The section should be single glazing using (flush catch) single point locking. The gasket should be made of EPDM (Ethylene propylene dimonomer) and applying silicon sealents (GE make or wacker make) outside and acrylic sealent inside including single glazing of 5mm thick clear float glass . The sections should be reinforced with GI sheet of 1.5 mm thick with suitable drainage grouting

Providing and fixing wash basin with C.I. brackets, 15mm C.P. brass pillar taps ,32mm C.P.brass waste of standard pattern ,including painting of fittings and brackets ,cutting and making good the walls wherever required - white vitreous china flat back wash basin size 450x300 mm with single 15mm C.P. brass pillar tap

Providing and fixing P.V.C. waste pipe for sink or wash basin including PVC waste fittings complete - flexiple pipe - 40mm dia

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6mm thick hard board backing - rectangular shape 453 x 357 mm

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour - 600 mm long towel rail with total length of645 mm, 78 mm wide and effective height of 88mm, weighing not less than 190 gms

Providing and fixing ASTM pipes including all ASTM plain& brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing . This includes jointing of pipes & fitting with one step ASTM solvent cement and testing of joints complete (Internal work exposed on wall ) - 20mm nominal outer dia pipes

Providing and fixing ASTM pipes including all ASTM plain& brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing . This includes jointing of pipes & fitting with one step ASTM solvent cement and testing of joints complete (Internal work exposed on wall ) - 25mm nominal outer dia pipes

Providing and fixing ASTM pipes including all ASTM plain& brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing . This includes jointing of pipes & fitting with one step ASTM solvent cement and testing of joints complete (Internal work exposed on wall ) - 32mm nominal outer dia pipes

Providing and fixing ASTM pipes including all ASTM plain& brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing . This includes jointing of pipes & fitting with one step ASTM solvent cement and testing of joints complete (Internal work exposed on wall ) - 40mm nominal outer dia pipes

Providing and fixing ASTM pipes including all ASTM plain & brass threaded fittings this included jointing of pipes & fittings with one step ASTM solvent cement , trenching refilling & testing of joints complete (External work) - 32 mm nominal outer dia pipes

Providing and fixing gun metal gate valve with C.I.wheel of approved quality (Screwed end) - 25mm nominal bore

Providing and fixing gun metal gate valve with C.I.wheel of approved quality (screwed end) - 20 mm nominal bore

Providing and fixing ball valve (brass) of approved quality , high or low pressure , with plastic floats complete - 25mm nominal bore

Providing and fixing unplasticised PVC connection pipe with brass unions - 45 cm length - 15mm nominal bore

Providing and fixing C.P.brass angle valve for basin mixer and geyser points of approved quality conforming to IS: 8931- 15 mm nominal bore

Providing and fixing PTMT bib cock of approved quality and colour - 15mm nominal bore, 90 mm long , weighing not less than 93 gms

Providing and fixing PTMT grating of approved quality and colour - circular type - 100mm nominal dia

Providing and fixing PTMT swivelling shower, 15mm nominal bore, weighing not less than 40 gms

Providing, laying and jointing UPVC pipes(Finolex / jain / Supreme / Truebore / Nandi) (0.4 Mpa)conforming to IS specification 4985 and ISI marked including transportation to the site , lowering to the trenches, laying to proper grade and alignment, testing of joints with required testing equipment,including cost of solvent cement,UPVC specials such as bends,tees, threaded pieces,couplers,reducer,endcaps etc.,complete all as per IS and CPWD specification. - 75mm dia.

Providing, laying and jointing UPVC pipes(Finolex / jain / Supreme / Truebore / Nandi) (0.4 Mpa)conforming to IS specification 4985 and ISI marked including transportation to the site , lowering to the trenches, laying to proper grade and alignment, testing of joints with required testing equipment,including cost of solvent cement,excluding UPVC specials such as bends,tees, threaded pieces,couplers,reducer, endcaps etc.,complete all as per IS and CPWD specification. - 110mm dia.

Providing and fixing in position UPVC moulded elbow (Finolex / jain)(1 Mpa) conforming to IS 7834 part II and ISI marked,including labour charges for jointing, jointing materials etc,complete - 110mm dia

Providing and fixing in position UPVC moulded elbow (Finolex / jain)(1 Mpa) conforming to IS 7834 part II and ISI marked,including labour charges for jointing, jointing materials etc,complete - 75mm dia

Providing and fixing 150 x 100 mm nickel Box Door lock with pair of keys of approved quality with necessary screws and bolts etc., complete as directed by the Engineer-in-charges .The rate is inclusive of all taxes

Providing and fixing PVC trap with PVC grating with or without vent arm complete including providing necessary lubricant and slip ring for fittings, cost of cutting and making good the walls and floors-110 mm inlet and 110 mm outlet as directed by the Engineer-in-charge

Providing a layer of trowel applied cementitious water proofing membrance of 5 mm thick nosminal SETSEAL TANKING-A pre packed water proofing / single part system over the SETSEAL APPLIED primer surface after wetting the surface includig all complete.

SETSEAL A-A pro packed water proofing two part system coating over the rough plastered surface after wetting the surface including all complete.

Chipping the worn out wall and concrete portion using proper tools and removing the loose particles and preparing the surface for treatment with wire brush etc., complete until to reach sound good surface as per the specification of M/s. DON construction chemicals India Ltd and removing the debris and disposal of the debris etc complete as directed by the Engineer-in-Charge with all leads and lifts upto floor five level.

Removing the loose particles /rust/mill scale deposits completely duly cleaning it with wire brush/crush sheet etc., and removing the dust over the old concrete surface and supplying a polymer based anticorrosive coating material CHMPATCH R of DON product (Two pack material with a powder and liquid component) and mixing mechanically until it is homogeneous and applying the same as one rich coat on prepared steel surface 0.50 kg/sqm of steel area as per the specification of M/s DON Construction Chemicals India Ltd. with all lead and lift etc., complete as directed by the Engineer-in charge. (Measurement as per the total area of treatment).

Providing high strength micro concrete CEMPATCH HM @ 27.75 Kg/sqm, a DON product over the Quickmast 108 applied area on columns, slabs, beams etc., upto floor five level. (aggregates of 6 mm to 12 mm chips may be added )Measurement has to be taken considering 15 mm thickness of repaired surface). For thick streatment precise quantity of water ie., 0.15 water powered ratio will be maintained for good mortar consistenance per the specification of M/s. DON construction Chemicals India Ltd. etc., complete as directed by the Engineer -in-charge.

Providing High strength polymer modified cementitious repair mortar CEMPATCH N @ 20.74 Kg/sqm, a DON product over the primer applied surface of 15 mm average thickness to make the surface smooth by trowel ling and finishing the surface neat as per the specification of M/s DON Construction Chemicals India Ltd. including all lead and lift Upto floor five level ete, complete as directed by the Engineer-in-charge.

Plastering the wall surface with Cement mortar of mix 1:4 (one part of cement :4 fine sand) mixed with polymer SETCRETE SBR at the rate of one Kg. for one bag of cement including applying a priming coat with SETCRETE SBR @ 0.27 Kg. Per Sqm of treatment area as per the specification of M/s DON Construction Chemicals India Ltd including all lead and lift etc., complete as directed by the Engineer-in- Charge.

Providng one coat of curing compound SETCTRETE 8 @ 0.20 litres / sqm a DON product over the plastered surface completely after deshuttering of concrete surface as final finishing of plastered surface as per the specification of M/s DON Construction Chemicals India Ltd including all lead and lift etc., complete as directed by the Engineer-in- Charge.

Disposal of building rubbish and unserviceable dismantled materials up to 5 kms-radius. The rate include incidental charges transportation by mechanical means, loading and unloading etc.,

E Gengadaran