SPECIAL REPAIRS TO P 22 P 23 P 24 OF ENROLLED PERSONS EPs MARRIED ACCN AT VIKRAM ENCLAVE AT HALDIA

Amount

Demolition of cement concrete (unreinforced) in ground floors and pavings n. exc 15 cm thickness (below or above ground level)and removing unserviceable material outside cantt area.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing unserviceble material out side cantt area.

Demolition of cement concrete in roofs,floors (other than ground floors),beams,staircases,landing,chajjas and removing unserviceable material out side cantt area.

Non skid ceramic coloured designer seamless tiles 7 to 8mm thick area of each tile exceeding 0.11 sqm but not exc 0.18 sqm,in floors etc.set and jointed in neat cement slurry and pointed in coloured cement to match the surface over and including 15mm thick screed bed in CM 1:4 complete all as specified and directed.

Non skid ceramic coloured designer seamless tiles 7 to 8mm thick area of each tile exceeding 0.18 sqm but not exc 0.38 sqm,in floors etc.set and jointed in neat cement slurry and pointed in coloured cement to match the surface over and including 15mm thick screed bed in CM 1:4 complete all as specified and directed.

25 mm thick PCC 1:2:4 type B-0 using (12.50 mm graded stone aggregates) as in floor finished even and rough.

Glazed ceramic coloured designer seamless tiles 300x450x7 to 8 mm thick on vertical surface as in skirting,dado set and jointed with neat cement slurry and pointed in coloured cement to match with the surface over and including 15mm thick screed in CM 1:4 complete all as specified and directed. .

Taking down chowkhat with shutter n exc 1.50sqm each (W/o taking off shutter from the frame) complete. (For window, ventilator & PVC door)

Solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, S&F in opening as per specifiecation & Drawing complete.

Factory made solid panel PVC door shutter 30 mm thick ( style ) consisting of frame work made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour P.V.C‘ C’ channel having a PVC sheet strip 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and as gap inserts for top rail; and bottom rail panelling of plain, colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles and rail with suitable PVC sheets beading and jointed together with solvent cement S&F in frame at site as per specification and drawing in SSR 2010 part-II.

75mm long but hinges, medium wt, cold rolled mild steel all as specified and as directed

Taking down shutter of any description exc 1 sqm and n exc 2 sqm each.

Taking down chowkhats or frames with shutters (W/O taking off shutters from the frames) exc 1.5 Sqm but n.exc 4 Sqm each & removing from site.

M&L 2nd claas hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and directed.

35mm thick factory made 2nd class HW plain, framed, panelled shutters (two panel) with lock rail and panel of 9mm B.W.P. commercial, ply or 12mm veneered particle board with commercial veneering on both face. The size of rail and style as per IS : 1003 (Part 1). complete all as specified and as directed.

35mm thick glazed skeleton shutters with 2nd class HW open rebated and prepared to recieve glass, gauze, etc (W/o sash bars), edges or framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass, etc size of member of shutters as specified and directed.

Stainless Steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.4 mm and fixed with stainless steel wire staples all as specified and directed.

Aluminium handle ,cast type,anodised size 150 mm long.

Aluminum, anodized, barrel towers bolt of extruded section and fixed 200 mm size.

Steel locking bolt with mild steel electrogalavnised plate and bright bolt not less than 10mm dia , 100 mm size.

Aluminum alloy 250 mm long, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminum alloy and fixed.

100mm long but hinges, medium wt, cold rolled mild steel all as specified and as directed

Applying two coats of synthetic enamel paint on wood/wooden based surfaces over one coat of pink primer including preparation of new surfaces over 10 cm width or girth.

Applying two coats of synthetic enamel paint on existing wood/wooden based surfaces including preparation of old surfaces of any description over 10 cm width or girth.

Taking down GI tubing of 15 mm dia and connections incl. cleaning for refixing or removing from site all as specified and directed.

Taking down GI tubing of 20 mm dia and connections incl. cleaning for refixing or removing from site all as specified and directed.

15 mm dia galvanised pipes' medium grade' with all fittings and fixed complete to wall and ceiling or laid in floors, incl cutting and chiseling.

Refixing only 15mm dia tubing and connections in new or old position including cleaning old tubing.

20 mm dia galvanised pipes 'medium grade' with all fittings and fixed complete to wall and ceiling or laid in floors.

Refixing only 20 mm dia tubing and connections in new or old position.

S&F anodised aluminium window/ ventilator shutters with frame, sliding type with styles, rails, sash bar, sliding frame etc. all are made from anodised aluminium section weighting 0.55 kgs/m including necessary joining cleats ,glazing clips, rubber packing with locking system anodised aluminium snap beading screws all as specified and directed.

PCC 1:3:6 type C1 (using 20mm graded stone agg) as in bed block for embeded hold fast for doors, window frames or chowkats including necessary form work complete all as specified.

Anodised aluminium grill, 10mm thick, diamond shape with apareture 75mm fixed to windows complete all as specified and as directed. Make - Deco Grill, model DG-104 or equivalent in / Jindal/ Hindal

5.5 mm thick sheet glass ordinary quality alongwith EPDM rubber all around the glass edges exc 0.50 sqm in each pane and fixed into aluminium frame work complete all as specified and as directed.

Granite 18 to 20 mm thick (PURE BLACK) (table rubbed and polished) as in steps, jambs, pillars, window cills cooking platforms and like in cement mortar 1:4 including pointing in white cement 1:2 using marble dust with admixture of pigment to match with shade of granite over & including 15mm thick screed bed in CM 1:4. Edges of slab to be rounded from all sides.

Taking down cement plaster of any description on brick or stone walls or from concrete surface incl raking out joints, hacking for key, scrubbing down with water etc all as specified,and removing unserviceable material outside cantt area.

Rendering 10 mm thick in CM 1:3 on fair face of concrete surfaces finished even and smooth without using extra cement as in ceiling etc. all as specified.

Rendering 15 mm thick in CM 1:4 on fair face of brick work surfaces finished even and smooth without using extra cement all as specified. ( incl all necessary scaffolding, lifting arrangement for external surfaces ) upto 4 story Bldg.

Rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6, finished even and smooth without using extra cement complete all as specified.

Repair to Chajjas/Facias n exc 1.0 sqm area upto 4 storey building including necessary formwork & scafolding, plaster on top, side and soffits of chajjas/facias wherever damaged, RCC 1:2:4 type B1 reinforced duly welded if required and necessary surface finished as per existing complete all as specified.

Repair to Chajjas/Facias exc 1.0 sqm area upto 4 storey building including necessary formwork & scafolding, plaster on top, side and soffits of chajjas/facias wherever damaged, RCC 1:2:4 type B1 reinforced duly welded if required and necessary surface finished as per existing complete all as specified.

Supply only Liquid water proofing compound.

Prepration of new surface of wall and Applying two coats of oil emulsion distemper including priming over a coat of 3mm thick wall putty complete all as specified and directed.

Prepration of old surface of wall and applying one coat of 3mm thick putty on wall complete all as specified.

Prepration of old surface of wall and applying two coats of oil emulsion with priming over a coat of 3mm thick wall putty complete all as specified.

Preparation of old plaster surface of wall and applying one coat of exterior emulsion paint (weather coat) complete all as specified.

Preparation of newly plaster surface of wall and applying two coat of exterior emulsion paint (weather coat) over a coat of alkali resistant primer complete all as specified.

Preparation of newly surface of ceiling & applying two coat of white wash complete all as specified.

Demolition of existing RCC of any description and any postion not otherwise (reinforcement cut as required to facilate demolition) all as specified and directed.

Rotational moulded polytehylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position of capacity 500 ltrs incl. making connections including 25 mm dia bore Ball Valve high pressure of PTMT with epoxy coated Aluminum rod and high density plastic ball screwed for iron pipe and fixed. (Minimum wt -455 gms) complete all as specified and directed.

50 mm thick PCC 1:3:6 type C-1 (20 mm graded stone agg) as in plinth protection finished even and fair complete all as specified and as directed.

Screed bed 15mm thick in CM 1:4 on surface or concrete surface finished even and rough for laying tiles complete all as specified.

Chequred cement concrete tiles 20 x 20 cm x25mm thick set jointed and pointed in neat cement slurry mixed with gray cement and pigment as in path all as specified and directed.

Vitreous china wash hand basin white ,Oval shape of size 550 x 400 mm dia including suitable size of CI brackets, brass chromium plated waste fitting 32 mm dia with long screw shank and fly nuts ,flange and vedded in red lead cement complete all as specified and directed.

Angle / Stop Valve cast copper alloy fancy type15 mm dia bore with capstan handle screwed down screwed for iron pipe or for brass ferrule with concealed fixed in repairs.

PVC low level flushing cistern valve less,syphonic action type of 10 ltrs capacity white with inlet, ball valve, float and handle incl. cast iron brackets, PVC flush pipe 32mm dia ,PVC connection (15x 450 mm) long, fancy type chromium plated angle valve of 15mm bore dia complete all as spfd.(Make:Parryware/Slimline/Hindware)

Vitreous china squatting pan 'Orissa' pattern ' size 580x440mm white, with integral foot rest 'P' or 'S' trap, front or back inlet including connection to trap and to flushing pipe,anti syphonage pipe, etc.incl. making good to floor as existing complete all as specified and directed by Engr-in-Charge.

Towel Rail 450mm long of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats ( Min. wt 170 gms.)

PTMT grating doom 125mm dia with waste hole including embedding in tiles with white cement complete all as specified.(Minimum weight 40 gms )

PTMT grating doom 100mm dia including embedding in tiles with white cement complete all as specified.(Minimum weight 25 gms ).

Stainless steel sink made of 1.00 mm thick sheet for kitchen or laboratory with plug,washers waste pipe including bedding in cement mortar to dwarf wall or including fixing cast iron cantilever brackets,connecting union to pipe, overall size 495mmx420mm, bowl size 410x330x160mm.

Bib tap cast copper alloy , chromium plated fancy type15mm dia with capstan handle screwed down screwed for iron pipe or for brass ferrule fixed in repairs.

15mm dia pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or w/o lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, scerwed for iron pipe and fixed complete all as specified.

Curtain rod 20 mm dia Aluminium fancy type complete with clamps, ring, ball shaped knobs at both end, all golden colour, complete all as directed by Engr-in-charge.

Removing existing treatment from roof surfaces,cleaning the surface of all foreign material such as fungus,moss,dust etc.by wire brushing and dusting,levelling the surface. (a) 10mm thick plastering in cement mortar 1:4 finifhed plastered surfaces even and smooth. The plastered surface shall be cured properly for seven days by ponding of water over roof. (b) Preparing and cleaning of fully dry cement plastered as per IS 3384, 1986 over the plastered surface and applying bitumen primer 85/25 grade @ 1.20 ltr/Sqm. (c) A layer of APP bases polymeric membrance, 3mm thick (min), weighing 3.5kg/Sqm reinforced with polyster non wovwn fabric (weighing n less than 160gms/sqm) shall be appllied over bituminous primer as specified above. Application of polymeric membrance shall be by torch application. The overlap shall be minimum 100mm on the transvers direction and 75mm on longitudinal direction. (d) Applying one coat of Aluminium paint @ 0.1 Ltr/Sqm over APP based polymeric membrance complete all as spd (NOTE:- The work shall be executed through authorised applicator approved by the manufacturers of membrane).MAKE:- TEXSA, LAFARGE, STP, BENGAL, AQUAFLUX.

Stop valves cast copper alloy 20 mm dia, screwed down, high pressure, with crutch and butterfly handle screwed both ends for iron pipes or for unions and fixed in repairs all as specified and directed.

Stop valves cast copper alloy 15 mm dia, screwed down, high pressure, with capstan handle screwed both ends for iron pipes or for unions and fixed all as specified and directed as in repairs.

Stop valves cast copper alloy 15 mm dia, fancy type,chromium plated with long shank and cup (concealed type) screwed down, high pressure, with capstan handle screwed both ends for iron pipes or for unions and fixed in repairs all as spfd .

Stainless steel plate rack of size 900mmx600mmx250mm made out of 1mm thick stainless steel sheet complete all as specified. Make:-Prestige / Devidayal

Soap dish, vitreous China white, approximate size 160 x 160 x 90 mm complete.

PVC connection 15mm size with PTMT nuts of length for 450mm complete.

Brass chromium plated shower rose 125 mm size fancy type, with CP neck 9 inch long with swivel joints, including fixing to steel pipe or union of 15 mm bore all as specified and directed.

Demolition & breaking up existing 150mm dia drain pipes(salt glazed stoneware, ac or reinforced concrete) pipe including PCC bed set in cement mortar & removing demolished material from site all as specified and as direted by Engr-in-charge.

PCC 1:3:6 type C2 (using 40 mm graded stone, aggregate) as in conncrete bed to drain pipes including packing under haunching against the sides of pipes after they are laid and tested for 150 mm dia SWG pipe all as specified and directed.

Salt glazed stoneware drain pipe 150 mm dia grade 'A' laid in trenches and jointed complete all as specified and directed.

MS TMT bars 10 mm dia and over, cut to length, bent to shape required including cranking, bending, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia as reinforcement complete all as specified & directed.

MS TMT bar 5 mm dia and over, upto and incl 10mm dia in stirrups , spacers and binder.

Demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed.

Brick work with sub class 'B' bricks straight or curved in plan exc 6 mtr mean radius built in CM (1:6) using old size bricks complete all as specified and as directed.

Brick work with sub class 'B' bricks straight or curved on plan to any radius in half brick thick wall built in CM 1:4 complete all as specified and directed.

Dismantling of 100 mm dia cast iron drain pipes, jointed in cement mortar and taking out old pipe complete all as specified and directed.

Cast iron (sand cast) soil, waste and vent pipe 100 mm bore in any length, with or without ears, with cement joints, fixed on walls complete all as specified and directed.

100 mm bore CI bends (any radius) with ducks foot / heel rest fitted with oval access door complete all as specified and directed.

RCC (nominal; mix), type B0 1:2:4 (using 12.5mm graded crushed stone aggregate) as in slab supported on wall, beams, columns, in floor, roof, landing, deck slab and in shelves and the like complete all as specified.

-ditto- All as per item No 85 but in chajja.

From work to Chullah hoods, chajjas troughs and similar items including edgs complete all as directed.

Welding in repairs exceeding 2.5 cm but not exceeding 5 cm in length, thickness excedding 9mm dia but not exceeding 20mm dia metal or bars.

Providing and applying bounding agent of approved brand coverage and specifications of manufactures (Mixed density : 1.48 kg/Ltr, Adhesive bond strength to be >2.50 Mpa) Epoxy bonding agent (In column & slab)

Machine cut kota stone slab flooring 20-25 mm thick over and including 15 mm thick cement screed bed 1 :4 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed

Kota stone slab 20-25 mm thick in riser of steps ,skirting ,dado and pillar laid over and including 10 mm thick in CM 1:4 screed and jointed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

Pre-cast reinforced cement concrete 1:2:4 type B1(using 20 mm graded crushed stone aggregate) as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces etc set in CM 1:6 including necessary forms, moulds etc complete all as directed.

Taking down carefully the existing copper point wiring of any size and capacity and type by disconnecting from the either terminals complete including fittings and fixtures such as switches, sockets,ceiling rose,fan regulators, lamp holders, call bell, bell pushes any type etc by unscrewing and taken away from site complete and make good the disturbed surface all as per existing. Note : Servicable Light fittings specified by Eng-in- charge shall be refixed.

Point wiring complete with PVC insulated and unsheathed cable 1.5 sq mm FRLS grade (nominal area) multi stranded copper counductor single core Conforming to IS : 694 including medium duty concealed unplasticised PVC conduit conforming to IS : 9537 ( Part-3) and ISI marked not less than 20 mm dia concealed in wall modular metal flush boxes as per manufacturer's design of reqd. size (factory made) including steel frame and modular cover plate made of polycorbonate with all accessories and all as specified including PVC insulated and unsheathed cable1.5 sqmm (nominal area) stranded copper counductor single core Conforming to IS : 694 of green colour as earth wire to common earth and connected to earth dolly drawn in same concealed conduit including cutting the chases and making good the surface by cement mortar(1:3) and for maching/finishing of new surface either by means of plaster of paris/putty or distamper/clour wash with same existing colour surface complete for following :-

One light /fan/exhaust fan point controlled by one switch

One 5 Amp socket outlet point on an independent board.

One 5 Amp socket outlet point on same board with other switches

One light point controlled by two switch single pole two way

One bell/buzzer point

Point wiring complete for one socket outlet 15 amps on an independent board with PVC insulated and unsheathed cable 4 sqmm (nominal area) FRLS grade stranded copper counductor single core conforming to IS : 694 including medium duty concealed unplasticised PVC conduit conforming to IS : 9537 ( Part-3) and ISI marked not less than 20 mm dia concealed in wall modular metal flush boxes as per manufacturer's design of reqd. size (factory made) including steel frame and modular cover plate made of polycorbonate with all accessories and all as specified including PVC insulated and unsheathed cable 2.5 sqmm (nominal area) stranded copper counductor single core Conforming to IS : 694 of green colour as earth wire to common earth and connected to earth dolly drawn in same concealed conduitincluding cutting the chases and making good the surface by cement mortar(1:3) and for maching/finishing of new surface either by means of plaster of paris/putty or distamper/clour wash with same existing colour surface complete all as specified and controlled by one 15 Amp switch.

Switch,modular type 6 amps single pole , one way conforming to IS : 3854 and ISI marked.

Socket modular 6 Amp ,2/3 pin flush type.

Switch, modular type 16 amps single pole , one way conforming to IS : 3854 and ISI marked.

Socket modular 6/16 Amp , 2/3 pin combined 2 module conforming to IS : 1293 and ISI marked.

Switch modular type 6 Amps single pole 2 way switch.

Bell push modular type 6 amps.

Bell, AC 230 Volts,single pole.

Ceiling rose , surface polycarbonate isolated body three terminals.

LED Wall / Surface mounted "Batton and tube rod integrated channel CRCA body, powder coated white regal batten type luminaire pre-wired for T8 LED tube light. 1x18W LED T8 6000K complete including taking down old one all as specified and as directed. Make Havells cat no.LUMILINEBS18WLED865SPCWH or euivalent of Phillips/Bajaj/CG.

LED fitting , wall mounted ,9 Watts, complete including taking down old one all as specified and as directed. Make : Havells cat no.LUMILINEBS9WLED865SPCWH or euivalent Phillips/Bajaj/CG.

Lamp Holder. PVC/Polycorbonate for LED lamp complete including taking down old one all as specified and as directed.

LED Bulb 9Watts complete including taking down old one all as specified and as directed.

Supply and Fixing the modular type stepped fan regulator , 120 Watts and connecting complete taking down old one all as specified

Sub main wiring concealed with 2 runs of 6 Sqmm PVC insulated HRFRLS Copper conductor cable including PVC conduit of 25mm dia along with one runs of 2.5 Sq.mm HRFRLS copper cable for earth continuity conductor as earth lead and connecting to common earth dolly complete including taking down old sub main wiring all as specified and as directed.Note: two runs 6 Sq.mm. cable, one runs of 2.5 Sq.mm cable and one run of PVC conduit will be measured as one unit.

Double door metallic sheet metal enclosure , TPN, 4 way,415 Volts (horizontal type)with 200 Amps rated bus bar , suitable for 32 Amps TPN MCB/ 4 pole Isolator(as incommer) fixed properly on in concealed position on wall and surface position on trusses and to provide required sizes of flexible conduit at any open surfaces near DBs for cables/wires complete all as specified and directed.

Distribution Board, SPN, 8 Way, Double door with 200 amps rated bus bar complete all including taking down old one DB as specified and directed.

Distribution Board, SPN, 4 Way, Double door with 200 amps rated bus bar complete including taking down old one all as specified and directed.

Isolator TPN, 415 volt 100 Amp ,10 KA capacity having C-curve characteristics connected with suitable lugs complete including taking down old one all as specicified and as directed.

MCB, SPN, 40 Amps 240 Volts C curve, 10KA breaking capacity complete Havells cat no DHMZCSPF040 or euivalent of Legrand/CG including taking down old one all as specified and as directed.

MCB, SP, 6-32A Amps 240 Volts C curve, 10KA breaking capacity complete Havells cat no DHMZCSPF006-032 or euivalent of Legrand/CG including taking down old one all as specified and as directed.

Taking down and refixing of Ceiling Fan/Exhaust/KWH meter fan in same position complete all as specified and directed.

Earthing complete with galvanized steel earth plate electrode 600x600x6 mm thick buried directly in ground (earth pit not less than 2.25 m deep below normal ground level) with top edge of the plate not less than 1.5 m below normal ground level connected to galvanized earth wire of 4 mm dia (up to 7.5 m in length from earth plate ) by means of bolts and nuts checknuts and washers of galvanized iron or steel all as specified and shown in electrical plate no.3 of SSR part I including necessary excavation and earth work in any type of soil PCC 1:3:6 type C1 chamber with RCC 1:2:4 type B1 40 mm thick cover with MS rod 8mm dia 150mm c/c reinforcement both ways, watering funnel, 20 mm dia light grade for protection of earth electrode 20 mm dia for watering complete including taking down old one all as specified and directed and tested on completion.

S&F hard drawn steel wire fabric cut to lengths, bent to shape required and tying with and including mild steel wire (annealed not less than 0.9mm in dia and fix in reinforcement wt per sqm n.exc 4 kg)

Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per sq.m of the vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc. complete

Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors

KAKOLI ENTERPRISE

BHARAT TRADING CORPORATION