Aaugumentation of Water Supply to the Kattamanikuppam OHT in Muthialpet, Puducherry Municipality and Rainbow Nagar OHT in Oulgaret Municipality, Puducherry 2nd call

Amount

Earthwork in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5m, including getting out the excavated soil and disposal of surplus excavated soil as directed , within a lead of 50m - all kinds of soil

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m - all kinds of soil - pipes,cables etc , exceeding 80mm dia but not exceeding 300 mm dia

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50m and lift upto 1.5m

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plith level - 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plith level - 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plith level - 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40mm nominal size)

Centering and shuttering including strutting , propping etc and removal of form for - foundations, footings, bases of columns etc for mass concrete

Brick work with common burnt clay F.P.S. (non modular ) bricks of class designation 35 in foundation and plinth in - cement mortar 1:6 (1 cement : 6 coarse sand)

Steel work welded in built up sections / framed work , including cutting,hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required - in gratings, frames, guard bar, ladder, railings, brackets,gates and similar works

12mm cement plaster of mix -1:4 ( 1 cement : 4 fine sand)

Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead - nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Demolishing cement concrete manually/by mechanical means including disposal of material within 50 metres lead - nominal concrete 1:4:8 or leaner mix (including equivalent design mix)

Dismantling manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead - bituminous road

Supply of Quarry rubbish including stacking to department gauge for premeasurement and spreading required thickness

Providing flanged joints to double flanged C.I./D.I. pipes and specials including necessary bolts, nuts, rubber insertion and testing of joints etc.,complete - 150mm diameter pipe.

Providing flanged joints to double flanged C.I./D.I. pipes and specials including necessary bolts, nuts, rubber insertion and testing of joints etc.,complete - 300mm diameter pipe.

Providing and fixing C.I. Double air valve with bolts, nuts, rubber insertion etc.,complete (the tail pieces if required will be paid separately) - 200 mm dia.

Providing and fixing C.I. Ball type non return valve (PN 1) conforming to IS 318 & IS 1363, with bolts, nuts, rubber insertion etc.,complete (the tail pieces if required will be paid separately) - 100 mm dia.

Providing and laying Ductile Iron socket and spigot pipes of class K9 (Electro steel/Sripipes/Jindal/Electrotherm / Jai Balaji / TATA Metaliks Kubota) conforming to IS specification 8329/2000 and ISI marked suitable for tyton /push on joints in good condition including transportation of D.I.pipe from production centre/company to the site at UT of Puducherry, lowering to the trenches, laying to proper grade and alignment, testing of joints with required testing equipment etc.,complete all as per IS 12288 and CPWD specification. (earth work and jointing of pipes with rubber gasket will be paid separately) -150mm dia.

Providing and laying Ductile Iron socket and spigot pipes of class K9 (Electro steel/Sripipes/Jindal/Electrotherm / Jai Balaji / TATA Metaliks Kubota) conforming to IS specification 8329/2000 and ISI marked suitable for tyton /push on joints in good condition including transportation of D.I.pipe from production centre/company to the site at UT of Puducherry, lowering to the trenches, laying to proper grade and alignment, testing of joints with required testing equipment etc.,complete all as per IS 12288 and CPWD specification. (earth work and jointing of pipes with rubber gasket will be paid separately) -200mm dia.

Providing and laying Ductile Iron socket and spigot pipes of class K9 (Electro steel/Sripipes/Jindal/Electrotherm / Jai Balaji / TATA Metaliks Kubota) conforming to IS specification 8329/2000 and ISI marked suitable for tyton /push on joints in good condition including transportation of D.I.pipe from production centre/company to the site at UT of Puducherry, lowering to the trenches, laying to proper grade and alignment, testing of joints with required testing equipment etc.,complete all as per IS 12288 and CPWD specification. (earth work and jointing of pipes with rubber gasket will be paid separately) -300mm dia.

Providing and laying Ductile Iron Double flanged pipes of class K9 (Electro steel/Sripipes/Jindal/Electrotherm) conforming to IS specification 8329/2000 and ISI marked suitable for flanged joints in good condition including transportation of D.I.pipe from production centre/company to the site at UT of Puducherry, lowering to the trenches(or fixing in over head tanks above ground level) laying to proper grade and alignment, testing of joints with required testing equipment etc.,complete all as per IS12288 and CPWD specification . (earth work and jointing of pipes with rubber insertion will be paid separately) -150mm dia.

Providing and laying Ductile Iron Double flanged pipes of class K9 (Electro steel/Sripipes/Jindal/Electrotherm) conforming to IS specification 8329/2000 and ISI marked suitable for flanged joints in good condition including transportation of D.I.pipe from production centre/company to the site at UT of Puducherry, lowering to the trenches(or fixing in over head tanks above ground level) laying to proper grade and alignment, testing of joints with required testing equipment etc.,complete all as per IS12288 and CPWD specification . (earth work and jointing of pipes with rubber insertion will be paid separately) -300mm dia.

Providing and fixing in position S&S standard D.I. specials (Electro steel/Sripipes/Jindal/Kiswok) such as tees, bends, collors, tapers, caps etc.conforming to IS specification 9523/2000 and ISI marked - 100 to 300mm dia.

Providing and fixing in position flanged standard D.I. specials (Electro steel/Sripipes/Jindal/Kiswok) such as tees, bends, collors, tapers, caps etc.conforming to IS specification 9523/2000 and ISI marked - 100 to 300mm dia.

Providing and jointing cast iron / D.I. (S&S) pipe joints with rubber gasket (Tyton joints) conforming to IS 5382 & 12820 of SBR quality including the cost of fixing,testing the joints etc.,complete -150mm dia.

Providing and jointing cast iron / D.I. (S&S) pipe joints with rubber gasket (Tyton joints) conforming to IS 5382 & 12820 of SBR quality including the cost of fixing,testing the joints etc.,complete -200mm dia.

Providing and jointing cast iron / D.I. (S&S) pipe joints with rubber gasket (Tyton joints) conforming to IS 5382 & 12820 of SBR quality including the cost of fixing,testing the joints etc.,complete -250mm dia.

Supplying of electrically operated wet type submersible motor and pumpset (Texmo/KSB/Taro/Kirloskar make), AC 3 phase, 415 volts, 50 Hz, 2900-3000 RPM. The pump shall have brass impeller, high grade steel shaft with sufficient stages having outlet size of 2"/2.5"/3" dia. to suit the borewell (150 / 200mm dia.), complete. The rate includes, all taxes, freight, etc., FOR at site in UT of Puducherry. The pumpset shall be guaranteed for a period of one year from the date of commissioning.(15 HP Submersible motor and pumpset).

Supplying and fixing C.T. metering panel board as per Electricity Department Specification (Drawing enclosed). Panel board of size 1800mm x 900mm x 300mm made of 18 gauge CRMS sheet painted with two coats of enamel paint over Zinc chromate primer with necessary MS base channel. The panel board shall include power mat, copper busbar, 8mm thick Hylan sheet of size 84 x 54cm.

Supplying and fixing of 10KVAR power capacitor (CG/L&T/Siemens make) for 17.5/20 HP motor complete.

Supplying and fixing of fully automatic air break star-delta starter range for 13A to 25A F.A.S.D. (Bharat Culter Hammer/L&T/Siemens make) with suitable M.S. angle frame etc., complete.- 20HP to 25HP pumpsets -(ML-1.5)

Supplying and fixing of 1x3x6 sqmm (single run) PVC insulated copper submersible flat flexible cable of Finolex make complete.-12.5HP to 20HP pumpset

Supplying of 3.5/ 4x25 sqmm underground cable (Paragon/suncab/Empire) complete.-upto 25HP pumpset.

Supplying of 3.5/4x50 sqmm underground cable (Paragon/suncab/Empire) complete.-suitable for (30HP to 40HP pumpset)/(upto 40KVA Genset).

Laying of UG cable and providing termination of cable joint with suitable cable gland,cable socket etc., complete - 3.5/4 x 25 sqmm cable.

Laying of UG cable and providing termination of cable joint with suitable cable gland,cable socket etc., complete - 3.5/4 x 50 / 3.5/4 x 70 sqmm cable.

Supplying and fixing of meter board of size 600mmx900mmx150mm on suitable angle frame with suitable water proof plywood 12mm thick for receiving ED supply. The board frame shall be painted and covered on all sides by 16 gauge M.S. sheet and fixed with 3 Nos. of 100 Amps fuse carrier (Havells/Standard/Anchor make) with screws etc., complete.

Supplying and fixing of teak wood aerial board with 100 Amps HRC fuse base and fuse link and suitable post clamp to hold the G.I. Pipe with electric post including bolts and nuts etc., complete.

Making earth pit of G.I. pipe for earthing in earth pit with 40mm dia. G.I. pipe medium class of length 3.05m perforated with 46 Nos of 12mm dia. holes, pipe lowered in bore holes of 150mm dia. and filled in with charcoal and salt in alternative layer of 300mm, the top of G.I. pipe shall be clamped. Earth pit shall be provided with 60cm dia precast ring with 60cm depth alround,covered with R.C.C. precast slab etc. as per I.E. standards.

Providing and fixing 50 mm dia GI pipe (Class B) conforming to IS 1239 (Part 1:1990) with GI fittings including trenching, refilling etc., complete for UG cable duct.

Supplying and fixing of pole clamp to hold the G.I. Pipe with electric post.

Supplying and fixing of copper flat (25 x 3mm) for earthing arrangements including bolts and nuts etc.

Supplying,fixing and lowering into the borewell high tensile threaded PVC column pipes which are to be connected to the submersible pump,including labour charges,jointing materials etc.,complete.-100 mm dia

Supplying and fixing of C.I. adopter which is to be connected to submersible pump delivery pipe.-75/80 mm dia

Supplying and laying of 16mm dia nylon rope for holding of motors.

Supplying and laying of 40mm dia. PVC pipe (Class 3 - PN 0.6 Mpa) conforming to IS 4985 : 2000 for inserting submersible cable from borewell to starter.

Supply and fixing of 80/100mm dia. M.S. erection clamps of size 80mmx12mm with bolts, nuts, washer etc., complete.

Erection, testing and commissioning of motor and pumpset complete.The rate includes obtaining electricity service connection from Electricity Department also.

Supplying of 3 phase, 415 volts, 50 cycles, 0.8 power factor for electric starting diesel generator comprising the following units:- (Kirloskar/Leyland/Ruston/Greaves Cotton/Cummins make) air cooled and shall be of multi stroke, multi cylinders, cold starting, developing not less than 56 BHP under normal temperature and pressure. The engine shall conform to I.S. 10002 with latest amendments. It shall be capable of taking 10% over load for one hour in every 12 hours of continous operation including 6 Nos. of anti vibration pads.The engine shall be complete with the following accessories:Electrical starting provision, engine cooling fan, fuel and lubricating oil filters, oil bath, air filter, lub oil pressure gauge 90 litres capacity fuel tank mounted with engine, hour meter with exhaust manifold, flexible pipe, 12 /24 volts electric starting equipment complete with starter, alternator and one 12 volts with 19 plates battery of make AMCO/STANDARD/EXIDE/DAGANITE (with Guarantee cards) of adequate capacity and low lubricating oil pressure/high temperature varying engine shut down devices.The Acoustic enclosure shall have the following: Acoustic enclosure shall be powder coated and fabricated out of 16 SWG CRCA MS sheet. The silent canopy shall be of nut bolt type construction. Powder coating is done after seven tank surface preparation process of sheet

metal. Canopy panel and doors shall have inside lining of FIRE-RETARDANT foam/Rock Wool as acoustic material. Four hinged doors shall be provided to canopy, one door shall have glass window for control panel.Base frame is fabricated either in ISMC channel or in sheet metal. The base frame is rugged in construction and designed for mounting engine and alternator, with cross members mounted on AVM. The base frame shall have provision for mounting of acoustic enclosure and it is having provision of lifting hook for convenient lifting of complete set, i.e. along with canopy, engine and alternator.Fuel tank shall be fabricated out of 14 SWG CRCA MS sheet and is part of base frame. It is duly painted and fitted with inlet and outlet connections of suitable capacity.The Acoustic enclosure shall be Type test approved as per CPCB norms. The average sound level, when measure in green field condition (ISO m3744 OR 8528 PT 10) at 1-meter distance from all four sides shall be less than 75-dBA average or as per CPCB norms. The average stabilized hot air temperature rise with in the canopy is maintained with in 10 C over and above ambient temperature.Acoustic enclosure is suitable for Outdoor / Indoor installation. Lockable doors shall be provided. Lockable fuel filling arrangement to be provided external to the canopy. Residential Silencer is housed in the

canopy. The exhaust gasses shall be taken out through a suitable flexible pipe to prevent any back pressure on the engine.Base frame sturdy, fabricated welded construction, channel iron / sheet metal base frame for mounting the above engine and alternator.Standard Tools and Spares:Double ended spanners complete set (small and big size sets) - 12 Nos. (TAPARIA/GEDORGE/EVEREST make)Screw driver (30cm long) Taparia make .Screw driver (45cm long) Taparia make .Cutting plyer.Diesel filter with elements - 2 Nos.Oil filter with elements - 1 No.All the above accessories with complete set.AlternatorThe alternator shall be of Crompton/Kirloskar/ Stamford/ELGI make, self excited, self regulated, screen protected, drip proof alternator with static excitation system capable of developing 40KVA at 0.8 power factor 415 volts, 3 phase, 50 cycles, generally conforming to I.S.4722 under normal condition, the voltage regulation will be plus or minus 5% of rated voltage. It shall be with end shield/ball roller bearings complete.Control PanelA wall/pedestal mounting (cubical type) fabricated sheet steel construction suitable for manual operation, rated for system output incorporating the following devices/instruments. The panel is made of 1.6mm sheet with one/two hinged front door, bolted back totally enclosed and vermine proof. It shall be with all

Providing and fixing of suitable M.S.exhaust pipe including 2 Nos. of M.S. bends (long), 7 Nos. of M.S. flanges, M.S. pipe Class B - 5 Rm as flexible exhaust pipe. The rate is inclusive of transportation charges for shifting of welding machine and gas cutting set to site, consumption of welding rod 10 SWG and cutting gas, providing fasterners of 10mm bolts / nuts / washers and flange gaskets including labour charges etc. as per IE standard.-65 mm dia exhaust pipe (upto 40 KVA)

Providing and laying of aluminium cladding with 50 mm thick glass wool slab with chicken mesh and covered with 24 SWG aluminium sheet (the rate includes double calculation for flanges & bends) as per I.E. standards.

Providing and fixing of fire safety equipments comprising 1 No. of 4.5 kg of CO2 fire extinquisher 1m x 2m x6mm thick rubber mat shock proof of superior quality with two numbers of 10 litres capacity fire buckets (red colour) with M.S. stand arrangements etc.

Providing and fixing of 4 pole change over switch of STANDARD/HAVELLS/KUNDAN/ GEM make including M.S. frame as per I.E. standard.-100 Amps (upto 50 KVA)

Charges for transporting, erection, testing and commissioning of generator set excluding foundation,but including mechanical and other unskilled wages for installation of equipment, wiring from generator set to panel board and change over switches, handling charges, purchase of spares if any required for the installation and commissioning, the cost of fuel and other materials for a trial run of 6 hours. This rate also includes for testing and commissioning of generator set as specified, obtaining approval of Central Electricity Authority (CEA), payment for CEA inspection/Licence fees or any other charges and fulfilling other requirements and conditions laid down by CEA-From 30 KVA to 50 KVA

Supply and installation of DI D/F Gate Valves (Soft seated ) Resilient seated soft sealing gate valves (Sluice valves ) (Make VAG,AVK,Fouress) with body bonnet of ductile iron of grade GGG 40, wedge fully rubber lined EPDM of good quality W720 , replaceable spindle nut, without gland packing and with 3 O-ring protection on the shaft and seals of NBR and the valves should be vacuum tight and 100% leak proof with face to face dimensions as per BSS 163-89/ISI 4846 - 2000/DIN3202 F4. All the valves should be Electrostatic powder coated both inside outside with pocket less straight thro body passage. All the valves shall be compatible for burried application without chambers, with pressure rating PN 10/16 - dia 150mm

Drilling of borewell any where in Pondicherry including tranportation in alluvial soil, sedimentary strata of clay, sand stone, shale, pebbles, boulders etc. by first taking a pilot bore of 140mm / 150mm / 200mm and then enlarging to required dia by direct or reverse rotary mud circulation method,including fuel, labour for drilling, bentonite mud, water required for drilling at the site, contruction of mud pit (water available within a lead of 1.5Km) using rotary rig. -Upto 60 mts depth ending below ground level.

Drilling of borewell any where in Pondicherry including tranportation in alluvial soil, sedimentary strata of clay,sand stone, shale, pebbles, boulders etc. by first taking a pilot bore of 140mm / 150mm / 200mm and then enlarging to required dia by direct or reverse rotary mud circulation method,including fuel, labour for drilling, bentonite mud, water required for drilling at the site, contruction of mud pit (water available within a lead of 1.5Km) using rotary rig. - From 60mts and upto 90 mts. depth ending below ground level.

Drilling of borewell any where in Pondicherry including tranportation in alluvial soil, sedimentary strata of clay,sand stone, shale, pebbles, boulders etc. by first taking a pilot bore of 140mm / 150mm / 200mm and then enlarging to required dia by direct or reverse rotary mud circulation method,including fuel, labour for drilling, bentonite mud, water required for drilling at the site, contruction of mud pit (water available within a lead of 1.5Km) using rotary rig. - From 90mts and upto 120 mts. depth ending below ground level.

Reaming from 200 mm dia pilot bore to 350mm dia bore. Upto 60 mts depth ending below ground level

Reaming from 200mm dia pilot bore to 350mm dia bore. From 60 mts and upto 90 mts depth ending below ground level

Reaming from 200mm dia pilot bore to 350mm dia bore. From 90 mts and upto 120 mts depth ending below ground level

Reaming from 300 mm dia pilot bore to 400/450mm dia. Upto 60 mts depth ending below ground level.

Reaming from 300mm dia pilot bore to 400/450mm dia bore. From 60 mts and upto 90 mts depth ending below ground level

Reaming from 300mm dia pilot bore to 400/450mm dia bore. From 90 mts and upto 120 mts depth ending below ground level

Charges for developing the borewells with air compressor of 600 CFM capacity (minimum 8 hours) including transportation labour and fuel charges for compressor and conducting yield test by "V" Notch methods.

Supplying of UPVC plain casing pipe for borewells (Finolex /Jain / Supreme / True bore / Nandi) conforming to I.S. 12818 -1992 with relevent amendments with class designation 'CM' and with minimum wall thickness 10mm including transportation and stocking at site -200mm dia

Supplying of UPVC ribbed screen slotted pipe for borewells (Finolex /Jain / Supreme / True bore / Nandi) conforming to IS 12818 -1992 with relevent amendments with class designation 'RS' and with minimum wall thickness 10mm including transportation and stocking at site - 200mm dia

Lowering of UPVC plain casing pipe / ribbed screen slotted pipes into the borewell including cost of cleaning material, fixing of M.S centering guide size of 25mm x 3mm thick suitable for 200mm dia UPVC pipe, including cost of labour for positioning of assembly for lowering purpose using rig.

Supplying transportation and packing of 8mm size down gauge graded pebbles including filling the annular space gradually complete. The pebbles disintegrated pieces. should be free from any disintegrated pieces.

Supplying,transporting and packing of clay balls including filling the annular space gradually complete. The clay balls should be free from any sand particles.

Providing and fixing M.S. top cover suitable for UPVC pipes including the cost of materials and labour etc.

Supplying and fixing electronic type battery charger unit for energizing the genset incuding charging indicator lamp,AC&DC fuses,AC supply ON&OFF control,DC output MCB, automaticfloat/booster charger rating 12V-15Amps capacity etc.,complete.

Providing and fixing of UPVC End Cap embedded in M.S. Cone suitable for UPVC casing pipe including the cost of materials and labour for jointing.

Foundation brickwork in CM 1 : 4 will be constructed in 23 cm wall for a height of 60 cm over foundation concrete PCC 1:5:10 for a width of 60 cm and 15 cm thick.The inside pump shed flooring will be laid in PCC 1:2:4 in 50 mm thick over a red earth filling of 15 cm thick and PCC 1:5:10 of 10 cm thick the outside area will be plastered in cement mortar 1:4, 12 mm thick etc. Complete as instructed by the Engineer-in-charge

Supply and providing of farbricated steel Kiosk of internal dimension, 2.20 x 1.90m with front and rear height of 2.40m and 2.10m respectively. The fabrication of the Kiosk is to as per the details below: The corner pillar of the Kiosk shall be of single equal M.S. angle 50x50x6mm tied up at the top, bottom and middle with 40x40x6mm angle, intermediate support of M.S. angles (2 Nos.) of 40x40x6mm in all 4 sides and stiffner in vertical with 40x6 mm flats and shall not exceed 0.50m C/C. For roof 2 Nos. of 40x40x6mm angles to a length of 1.90m each with 3 Nos. of 40x6mm flat for a length of 2.20m shall be provided.For front door portion an extra angle of 40x40x6mm of 2.40m as vertical and as horizontal lintel of 0.65m of the same angle are to be provided. The door shall be of 0.60m x 1.85m with 40x40x6mm angle on all the four sides with 1 No. of intermediate horizontal angle of 40x40x6mm with cross stiffener of 40x6mm flats for the doors shutters. The sides of the Kiosk shall be of 18SWG GI corrugated sheet and roof shall be colour coated galvalume sheet of 550 M.P.A.yield of AZ 150 strength formed as per patterned steel rib profile with the depth of 31mm pitch of 250mm and overall width of 1060mm and thickness 0.5mm with required J or C hook

bolts & nuts 8mm dia. The rate shall included the cost of all materials, labour, fabrication charges including providing of locking arrangements for the door painting cost with steel primer and paint charges for the angles, painting two coats of enamel paint both side and outside the Kiosk, transportation to newly erected borewell site in villages in Puducherry region etc. and erected on platform as directed by the Engineer-in-charge.

Excavation for roadwork in soil with hydraulic excavator of 0.9cum bucket capacity including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections and transporting to the embankment location with all lifts and lead upto 1000m.

Providing , laying , spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the material with water at OMC in mechanical mix plant carriage of mixed material by tipper to site , laying in uniform layer by manual means in sub-base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density - Using vibratory roller

Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth 3 wheeld steel roller 8-10 tonnes in stages to proper grade and camber, applying and brooming requisitecrushable type such as moorum or gravel for screening and gravel for binding to fill up the interstices of coarase aggregate, watering and compacting to the required density by manual means - water bound macadam Gr-II with moorum or gravel screening (as per MoRTH specification, 4th Revision)

Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth 3 wheeled steel roller 8-10 tonnes in stages to proper grade and camber, applying and brooming requisite type B screening and binding materials to fill up the interstices of coarse aggregate, watering and compacting to the required density - by manual means - Water bound macadam Gr-III with moorum or gravel screening. (As per MoRTH specification, 4th Revision)

Providing and applying primer coat with bitumen emulsion on prepared surface of granular base including clearing of road surface and spraying primer at the rate of 0.60 kg/sqm using mechanical means. (As per MoRTH specification, 4th Revision

Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 kg. Per sqm. on the prepared bituminous / granular surface cleaned with mechanical broom. (As per MoRTH specification, 4th Revision)

Providing and laying bituminous macadam with hot mix plant of capacity not less than 40 -60 TPH using crushed aggregates of specified grading premixed with bituminous binder, transported to site, laid over a previously prepared surface with paver finisher to the required grade, level and alignment and rolled as per clauses 501.6 and 507.7 of MoRTH specification, 4th Revision, to achieve the desired compaction. - using grade II metal and bitumen 60/70 grade.

Providing and laying bituminous concrete with HMP of capacity not less than 40 to 60 TPH using crushed aggregates of specified grading, premixed with bituminous binder @ 5.4 to 5.6 percent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per clause 509 of MoRTH specification, 4th Revision, complete in all respects - Using grade-II material.-Bitumen 60/70

Venkadesan R

MKM Constructions

Kavipriya Contractors