Providing CAMC AMC for HVAC VRV, Fire Alarm and PA, CCTV, EPABX, Electrical, IT, AV etc. items for IREDA office, IBC, EKN, 7th floor, Tower-2

CAMC/AMC ESTIMATE FOR HVAC/VRV, FIRE ALARM & PA, CCTV, EPABX, ELECTRICAL, IT, AV etc. ITEMS FOR IREDA OFFICE, IBC,

EKN, 7th FLOOR, TOWER-2

Amount (Rs) Amount (Rs) Amount (Rs)

Consumable Items

Note: Consumable items shall be executed as per the requirement of the

11 client/site, subject to prior approval from IREDA/EIC. It is also to be noted that

the bidder shall claim rates only from the latest DSR for items that are

Note:- S.no 2 pertains to LV And from S.No. 3-9 pertains to ELV works as per similar work in the NIT

Digitally signed by AMIT

CAMC/AMC ESTIMATE FOR HVAC/VRV, FIRE ALARM & PA, CCTV, EPABX, ELECTRICAL, IT, AV etc. ITEMS FOR IREDA OFFICE, IBC, EKN, 7th FLOOR, TOWER-2

Executed No. of

A CAMC of HVAC/VRV:

Modular type Variable Refrigerant Flow/Variable Refrigerant Volume air cooled Outdoor units suitable for

cooling and heating, having all hermetically sealed inverter type Scroll Compressor(s), minimum two

compressors for above 14 HP modules, microprocessor based Controller, top discharge type condensing

unit(s), with R 410 A Refrigerant, vibration isolators, with suitable foundation etc. complete as required. The

1 unit shall deliver the rated capacity at AHRI Conditions and work even at 50°C ambient temperature without per HP 40.00

tripping. The unit shall be suitable to work on 400V +/- 10%, 3 Phase, 50Hz AC power supply. The unit shall

be filled with first charge of the refrigerant and ready for use as required. The COP at AHRI conditions shall

not be less than 3.1 and IEER not less than 6.5 .

4-way flow VRV/VRF Cassette Type Indoor ceiling mounted unit equipped with synthetic washable media pre-

filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX

Copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration

isolation, cord less remote control etc., suitable for operation on single phase 230 V ± 10%, 50Hz AC supply,

2 complete, as required. The unit shall have automatic force shut down provision in case of fire on receiving

signal from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB

and 19 Degree C

WB temperature.

Inverter type High Wall Indoor Unit with Stablizer, 3 star, including cost of copper piping (upyo 15

mtr, drain pipe wire and remote)

3 High Wall - 2 Tr (Inverter Compressor with stablizer) Nos 2

VAV BOX (WITH INTEGRAL SOUND ATTENUATOR)

Pressure independent rectangular VAV unit with integral sound attenuator made of 22G GI sheet

casing length 900mm consisting of 25mm thick 48kg/m3 density fiber glass wool covered with

4 tissue paper ,elliptical volume control damper , calibrated differential pressure sensor (DPT

sensors) at inlet complete with digital Thermostat.( All VAV shall be factory calibrated ).

Digitally signed by AMIT

Executed No. of

Variable Frequency Drive (VFD)

380-400 VAC, IP-54 Chassis, RFI class A1 (C2), No brake chopper.

B CAMC of Electrical:

The following sheet steel cubicle type panels fabricated from 1.6mm thick CRCA sheet, dust and vermin

proof, indoor type TPN Panels with hinged lockable doors fabricated from 2mm thick CRCA sheet, suitable

for 415V, 3 phase 4 wire 50Hz AC supply with rear access for cable alley and with segregated bus-bar

1 chamber with tinned aluminium bus bar and including supplying and fixing following switchgears, meters Each 1 2,741.00 12.00 32,892.00

and accessories, inter-connections, bonding to earth, powder coated painting and marking as specified.

Switch boards complete as per schematic diagram:

Type of construction: Form 3

IP classification: 42

The LT PANEL shall be electrically inter-locked as shown in Schematic diagram and as detailed in the

Colour: Gray Powder Coated, as per approved sample.

1 nos, 250 Amps. 4 pole MCCB , i.e four pole Moulded Case Circuit Breaker of fault breaking capacity 25 KA

(ICS=ICU up to 433 V) complete in all respect

TPN aluminum bus bars of minimum of 320 Amps capacity with heat shrinkable colored sleeves and I/C

DMC/SMC bus bars supports at required intervals complete for cross section, size supports & their spacing

etc. for withstanding fault level of 25 MVA for 1 Sec.

(a) 63 Amps, TPN, MCB -6 Nos.

(b) 40 Amps, TPN, MCB - 6 nos

(c ) 125 Amps TPN MCB - 4 nos

Panel complete as above

The following sheet steel cubicle type panels fabricated from 1.6mm thick CRCA sheet, dust and vermin

proof, indoor type TPN Panels with hinged lockable doors fabricated from 2mm thick CRCA sheet, suitable

for 415V, 3 phase 4 wire 50Hz AC supply with rear access for cable alley and with segregated bus-bar

2 chamber with tinned aluminium bus bar and including supplying and fixing following switchgears, meters Each 1 2,330.00 12.00 27,960.00

and accessories, inter-connections, bonding to earth, powder coated painting and marking as specified.

Switch boards complete as per schematic diagram:

Type of construction: Form 3

IP classification: 42

The LT PANEL shall be electrically inter-locked as shown in Schematic diagram and as detailed in the

Digitally signed by AMIT

Executed No. of

Colour: Gray Powder Coated, as per approved sample.

Two (2) nos, 125 Amps. 4 pole MCCB , i.e four pole Moulded Case Circuit Breaker of fault breaking capacity

25 KA (ICS=ICU up to 433 V) complete in all respect

TPN aluminum bus bars of minimum of 400 Amps capacity with heat shrinkable colored sleeves and I/C

DMC/SMC bus bars supports at required intervals complete for cross section, size supports & their spacing

etc. for withstanding fault level of 25 MVA for 1 Sec.

1 Nos. 250A, 4P, MCCB (25kA) with phase indicating lamp protected with 2A, SP, MCB's along with E/M

(a) 63 Amps, TPN, MCB - 2 nos

(b ) 40 Amps, TPN MCB - 6 nos

Panel complete as above

High Efficient 60kVA/60 KW Model IGBT Rectifier & IGBT Inverter, Modular Fault Tolerant designFailure in

any one of the module the others keeps supplying to the load without interruption. Approved Make, 12V

VRLA Batteries, 65 AH or saiuitable for 30 minutes backup. Exide (40 nos on each bank) Make Exide,

3 Accessories ( Cabling between UPS and the Battery upto 10 Mtr distance for each UPS considering cable NO. 2 41,376.00 12.00 4,96,512.00

Routing,Battery Rack and Battery Interlinks, lugs etc ) DC MCCB between UPS and Battery complete in all

respect as per the directions of engineer in charge. UPS shall produce 30 minutes backup.

C CAMC of IT Active Works:

24-Port Layer 3 Stackable Managed Gigabit Switch, 20 x 10/100/1000BASE-T ports With 4 x Combo

10/100/1000BASE-T/SFP ports, 4 x 10G SFP+ ports, Switch Resource Management (SRM) for flexible

1 management of system resources, Redundant Power Supply (RPS) support, MPLS L2VPM/L3 VPN support, Nos. 1.00

Full L3 routing protocol support including OSPF, BGP, and ISIS for IPv4/IPv6. As Approved by NSL Incharge.

Access Switch of 48 x 1G POE+, 4 x SFP+ , 370W PoE, Switching Capacity of switch is of 176 Gbps having

Forwarding performance (64-byte packet size): 130 Mpps, Secure Shell (SSH), RADIUS, TACACS + DRAM 2GB

2 , Flash 2GB , 10K IPv4 Routes ,1K multicast Routes ,16K MAC address , 16K flow entries L3 Protcols like OSPF , Nos. 6.00

PBR, MACsec, PIM , QOS from day-1 , As Approved by NSL Incharge.

48 port 10/100/1000 Base T Switch with 4 x 10G SFP+ ports,The Switch should have 16K MAC address,

Should have RJ-45 console port should support MSTP and DUAL configuration, Should support Static 75,503.00 12.00 9,06,036.00

Route Entry: IPv4 124; IPv6 50 , Should support IP-MAC- Port Binding strictly management network devices

3 preventing illegal access and the Man-in- the-middle attack, Should support Asymmetric VLAN, Auto Voice Nos. 6.00

VLAN, Should support Cable diagnostics, Time-based PoE: PoE ports can be turned on/off by port or

system through schedule, Operating Temperature -5 to 50°C (23 to 122°F). As Approved by NSL Incharge.

Digitally signed by AMIT

Executed No. of

Wi-Fi standard, IEEE’s new 802.11ac Wave 2 specification, and meets the growing requirements of wireless

networks by delivering a better user experience. The 1830 Series extends support to a new generation of Wi-

4 Fi clients, such as smartphones, tablets, and high-performance laptops that have integrated 802.11ac Wave Nos. 30.00

1 or Wave 2 support.

5 Modules 10G - 30 Nos. & LC- LC multimode OFC type patch cord - 10 Nos. Lot 1.00

C.1 AMC of Passive Works:

Annual Maintenance Contract of Passive Components System having Following Equipments:

UTP Components for Data - 1 Lot

UTP Components for Voice - 1 Lot

200 Pair MDF Box -1 Lot

UTP Components for Wifi - 1 Lot

UTP Components for CCTV and Access Control - 1 Lot

D CAMC of AV Works:

98" smart 4K LED Display,Native Resolution 3840 x 2160 (UHD), Brightness Minimum 490cd/m2,

Inputs HDMI-3,USB(3.0)-3,USB-(2,0)-2,OPS Slot-1,RGB-1, LAN-1,SPDIF-1 or Higher, Output

Audio-1( Audio out to connect additional Speakers if required) , Built in Touch type IR spread /P

Cap/Incell/Inglass, Touch Accuracy ±1.5mm or less, Operating System Support Windows

7/8/10/Windows XP/Linux/Mac/Android (Windows XP/Linux/Mac Support one point touch) ,

Multi touch point Min 20 Points or Higher, White Board ,Writing, Pen, Palm Eraser ,Save, Screen

1 Capture, Storage, Tool Bar, Air Class etc , Android 9.0 or better , Internal Memory (32GB),(Hisi Nos. 2

811, Dual core A73+Dual core A53), DDR(4GB), Wi-Fi, Power Indicator, or higher, Screen

Share/Mira cast to Connect TAB/Mobile, Web Browser , 100-240V~, 50/60Hz, 32W(16W x 2) or

higher , ISO9001, ISO14001,ISO45001,

The display should be a smart screen and touch enabled alongwith stylus/pen. The display should

also have provision for OPS PC.

Digitally signed by AMIT

Executed No. of

55" smart 4K LED Display,Native Resolution 3840 x 2160, Brightness Minimum 390cd/m2, Inputs

HDMI-3,USB(3.0)-3,USB-(2,0)-2,OPS Slot-1,RGB-1, LAN-1,SPDIF-1 or Higher, Output Audio-1(

Audio out to connect additional Speakers if required) , Built in Touch type IR spread /P

Cap/Incell/Inglass, Touch Accuracy ±1.5mm or less, Operating System Support Windows

7/8/10/Windows XP/Linux/Mac/Android (Windows XP/Linux/Mac Support one point touch) ,

Multi touch point Min 20 Points or Higher, White Board ,Writing, Pen, Palm Eraser ,Save, Screen

55" main Capture, Storage, Tool Bar, Air Class etc , Android 9.0 or better , Internal Memory (32GB),(Hisi

2 LED 811, Dual core A73+Dual core A53), DDR(4GB), Wi-Fi, Power Indicator, or higher, Screen Nos. 4

display Share/Mira cast to Connect TAB/Mobile, Web Browser , 100-240V~, 50/60Hz, 20W(10W x 2) or

higher , ISO9001, ISO14001,ISO45001,

The display should be a smart screen and touch enabled alongwith stylus/pen. The display should

also have provision for OPS PC.

Portable USB Video Confrencing camera,PTZ Camera, 20X Optical Zoom, Digital Zoom: Up to 12X

USB Wide Viewing Angle up to 72.5 Degrees, RJ-45 Port, Quiet Motor with Servo Algorithm for PTZ

3 Control, Full HD 1080p signal output format with a high frame rate of 60 fps, HDMI, and USB 3.0 Nos. 1

synchronous video outputs

Wireless digital boundary layer Microphone with 18 or more channel, RF output 80mW or more,

Cardioid pickup pattern, Frequency range : 1880 to 1930 MHz, Connectivity : RJ-45, 256-bit AES

4 MICS Encryption (specifications includes single microphone set of transmitter and receiver) etc and Nos. 14

complete as required.

wireless digital microphone charger, charging capacity : 2 or more simultaneously with lighting

Charger indication, Qi charging, Should be from same OEM as of wireless mic etc and complet required as

base per specifications.

Digital signal processor with minimum 14no. Or more Mic / line input with phantom power and

AEC and 8 or more line output, at least 2 channel of USB input and output for software Video

Conferencing,, Should have sampline rate of 48kHz or better, Should be expandable for port

6 DSP expansion. 64x64 or more Dante Input for Digital audio transfer as per need,should support Set 1

Control with App via iOS and Android devices, or any third-party control system, Shall have Built-

in filters, feedback suppression, AGC etc complete as required as per specifications

6.5" two-way coaxial thin edge ceiling loudspeaker, 100V transformer power taps : 24,12,6, watts,

Ceiling Conical dispersion : 145° or more, impedance : 8, low impedance RMS continous power : 30watts,

7 frequency range : 50 Hz - 20 kHz or better, frequency response : 60Hz - 20KHz or better etc Nos. 12

complete required as per specifications.

Digitally signed by AMIT

Executed No. of

Quad channel Amplifier, 4 X 120watt or more, THD+N (@ 1 kHz) : < 0.3%, Technology : Class-D,

Common mode rejection ratio : 70dB or better, Temperature controlled FAN, Switching mode

8 power supply, should have Protection features like : DC Short circuit & Over heating & Over load & 1

Signal limiting etc, Built-in high pass filter and gain adjustment option etc complete required as per

specifications.

This HDMI Switcher/ Splitter 8x4 can connect 2HD signal sources with 8HD display terminals. It can

easily split 2-way HD signal sources to 8 HDTVs or projectors which support HD. It also can amplify

the HDMI signal. The two input HD signal sources can be switched freely. The HDMI Switch/Splitter

2x8 can support highest video resolution 3840x2160/30hz,Compatible with fully HDMI 1.3/1.4

Specification compliant. buffer HDMI signals at the same time, HDMI or DVI to HDMI cables used

for inputs and outputs. Included IR remote adapter for operational flexibility and easy control, no

manual clicking the select button needed. Support single high definition display and multiple

output HD signal sources, such as DVD Players, A/V receiversand Set Top Boxes, 360 Sky Box

Freesat Virgin Bluray Player DVD HDTV Projector Camcorder HTPC Laptop

65" smart 4K LED Display,Native Resolution 3840 x 2160, Brightness Minimum 390cd/m2, Inputs

HDMI-3,USB(3.0)-3,USB-(2,0)-2,OPS Slot-1,RGB-1, LAN-1,SPDIF-1 or Higher, Output Audio-1(

Audio out to connect additional Speakers if required) , Built in Touch type IR spread /P

Cap/Incell/Inglass, Touch Accuracy ±1.5mm or less, Operating System Support Windows

65" main 7/8/10/Windows XP/Linux/Mac/Android (Windows XP/Linux/Mac Support one point touch) ,

11 LED Multi touch point Min 20 Points or Higher, White Board ,Writing, Pen, Palm Eraser ,Save, Screen Nos. 1

display Capture, Storage, Tool Bar, Air Class etc , Android 9.0 or better , Internal Memory (32GB),(Hisi

811, Dual core A73+Dual core A53), DDR(4GB), Wi-Fi, Power Indicator, or higher, Screen

Share/Mira cast to Connect TAB/Mobile, Web Browser , 100-240V~, 50/60Hz, 20W(10W x 2) or

higher , ISO9001, ISO14001,ISO45001.

Portable USB Video Confrencing camera,PTZ Camera, 20X Optical Zoom, Digital Zoom: Up to 12X

USB Wide Viewing Angle up to 72.5 Degrees, RJ-45 Port, Quiet Motor with Servo Algorithm for PTZ

12 Control, Full HD 1080p signal output format with a high frame rate of 60 fps, HDMI, and USB 3.0 Nos. 2

synchronous video outputs

Digitally signed by AMIT

Executed No. of

USB: 2.0 (micro-B to Type A) ▪ Bluetooth 5.0, Class 1 (HFP/HSP/A2DP) ▪ NFC for easy pairin, Audio

Specifications ▪ OmniSound ® HD voice ▪ Speaker:

╶ Frequency response: 100Hz to 20,000Hz ╶ Volume: 90dB (SPL 0.5m) ▪ Microphones: ╶ 4 MEMS

microphones: 100Hz to 7,000Hz ╶ Pickup range: 20ft/6m

▪ Audio expansion: daisy chain connection (future release). ▪ Full Duplex▪ Acoustic Echo

Wireless Cancellation and Noise Suppression, Touch buttons: ╶ Answer call / Power

▪ LED Status Indicators ╶ Power status╶ Call status

╶ Bluetooth status ╶ Battery status ▪ Upgradable Software ▪ Upgradable Software, Integrated

Lithium Polymer Battery ╶ Call time up to 14 hour, Temperature range: 5°- 40°C ▪ Relative

humidity: 20 – 80% condensation-free

Active speaker pair of 35 watt, Transducers: LF: 135 mm (5.25 in) low frequency loudspeaker HF:

19 mm (.75 in) Polycarbonate dome tweeter Frequency Range: 80 Hz - 20 kHz Amplifier Power: 35

Watts per channel Maximum SPL Per Pair: 115 dB Crossover Frequency: 4.2 kHz

Input Sensitivity: +4 dBu XLR 1/4"; 0 dBu RCA

Signal Input Connectors (x2): Balanced Neutrik* Combo XLR 1/4" TRS; Unbalanced RCA Power

Requirements: 19 VDC / 3.42 A - use only supplied power supply

Headphone Jack: 3.5 mm (1/8") Dimensions: 235 x 159 x 143 mm (9.3 x 6.3 x 5.6 in). tudio quality

transducers for accuracy, and rich bass response: 80 Hz - 20 Khz

Active 35 watt per-channel power amplifier and high sensitivity drivers produce exceptional output: 115

14 DB max SPL per pair Balanced XLR, ¼”, and unbalanced RCA inputs allow connection to a range of Pair 2

signal sources Stereo headphone jack allows monitoring using headphones Ergonomic, side-

mounted volume control - simultaneously controls left and right speakers High frequency adjust

control - allows the user to contour HF response to application requirements

Magnetically-shielded transducers for use near CRT monitors and magnetically sensitive

equipment Internal peak limiter and overload protection circuit - protects the system from

damage caused by continuous over-driving

Wall-mount capable using optional MTC-2P mounting kit

Included snap-on pedestals optimize listening angle

for desktop applications including cabling etc as per instruction of Engineer In charge

Meeting Room 07 PAX (2 Nos)

Digitally signed by AMIT

Executed No. of

75" smart 4K LED Display,Native Resolution 3840 x 2160 (UHD), Brightness Minimum 390cd/m2,

Inputs HDMI-3,USB(3.0)-3,USB-(2,0)-2,OPS Slot-1,RGB-1, LAN-1,SPDIF-1 or Higher, Output

Audio-1( Audio out to connect additional Speakers if required) , Built in Touch type IR spread /P

Cap/Incell/Inglass, Touch Accuracy ±1.5mm or less, Operating System Support Windows

75" main 7/8/10/Windows XP/Linux/Mac/Android (Windows XP/Linux/Mac Support one point touch) ,

15 LED Multi touch point Min 20 Points or Higher, White Board ,Writing, Pen, Palm Eraser ,Save, Screen Nos. 2

display Capture, Storage, Tool Bar, Air Class etc , Android 9.0 or better , Internal Memory (32GB),(Hisi

811, Dual core A73+Dual core A53), DDR(4GB), Wi-Fi, Power Indicator, or higher, Screen

Share/Mira cast to Connect TAB/Mobile, Web Browser , 100-240V~, 50/60Hz, 20W(10W x 2) or

higher , ISO9001, ISO14001,ISO45001.

Portable USB Video Confrencing camera,PTZ Camera, 20X Optical Zoom, Digital Zoom: Up to 12X

Wide Viewing Angle up to 72.5 Degrees, RJ-45 Port, Quiet Motor with Servo Algorithm for PTZ

USB Control, Full HD 1080p signal output format with a high frame rate of 60 fps, HDMI, and USB 3.0

Camera synchronous video outputs

USB: 2.0 (micro-B to Type A) ▪ Bluetooth 5.0, Class 1 (HFP/HSP/A2DP) ▪ NFC for easy pairin, Audio

Specifications ▪ OmniSound ® HD voice ▪ Speaker:

╶ Frequency response: 100Hz to 20,000Hz ╶ Volume: 90dB (SPL 0.5m) ▪ Microphones: ╶ 4 MEMS

microphones: 100Hz to 7,000Hz ╶ Pickup range: 20ft/6m

▪ Audio expansion: daisy chain connection (future release). ▪ Full Duplex▪ Acoustic Echo

Wireless Cancellation and Noise Suppression, Touch buttons: ╶ Answer call / Power

Mic ╶ End Call ╶ Bluetooth ╶ Volume Up / Down ╶ Mute

▪ LED Status Indicators ╶ Power status╶ Call status

╶ Bluetooth status ╶ Battery status ▪ Upgradable Software ▪ Upgradable Software, Integrated

Lithium Polymer Battery ╶ Call time up to 14 hour, Temperature range: 5°- 40°C ▪ Relative

humidity: 20 – 80% condensation-free

Digitally signed by AMIT

Executed No. of

Active speaker pair of 35 watt, Transducers: LF: 135 mm (5.25 in) low frequency loudspeaker HF:

19 mm (.75 in) Polycarbonate dome tweeter Frequency Range: 80 Hz - 20 kHz Amplifier Power: 35

Watts per channel Maximum SPL Per Pair: 115 dB Crossover Frequency: 4.2 kHz

Input Sensitivity: +4 dBu XLR 1/4"; 0 dBu RCA

Signal Input Connectors (x2): Balanced Neutrik* Combo XLR 1/4" TRS; Unbalanced RCA Power

Requirements: 19 VDC / 3.42 A - use only supplied power supply

Headphone Jack: 3.5 mm (1/8") Dimensions: 235 x 159 x 143 mm (9.3 x 6.3 x 5.6 in). tudio quality

transducers for accuracy, and rich bass response: 80 Hz - 20 Khz

35 watt per-channel power amplifier and high sensitivity drivers produce exceptional output: 115

DB max SPL per pair Balanced XLR, ¼”, and unbalanced RCA inputs allow connection to a range of

signal sources Stereo headphone jack allows monitoring using headphones Ergonomic, side-

18 mounted volume control - simultaneously controls left and right speakers High frequency adjust Pair 1

control - allows the user to contour HF response to application requirements

Magnetically-shielded transducers for use near CRT monitors and magnetically sensitive

equipment Internal peak limiter and overload protection circuit - protects the system from

damage caused by continuous over-driving

Wall-mount capable using optional MTC-2P mounting kit

Included snap-on pedestals optimize listening angle

for desktop applications including cabling etc as per instruction of Engineer In charge

19 Meeting Room 06 PAX x 2 Nos

65" smart 4K LED Display,Native Resolution 3840 x 2160, Brightness Minimum 390cd/m2, Inputs

HDMI-3,USB(3.0)-3,USB-(2,0)-2,OPS Slot-1,RGB-1, LAN-1,SPDIF-1 or Higher, Output Audio-1(

Audio out to connect additional Speakers if required) , Built in Touch type IR spread /P

Cap/Incell/Inglass, Touch Accuracy ±1.5mm or less, Operating System Support Windows 2,19,415.00 12.00 26,32,980.00

7/8/10/Windows XP/Linux/Mac/Android (Windows XP/Linux/Mac Support one point touch) ,

Multi touch point Min 20 Points or Higher, White Board ,Writing, Pen, Palm Eraser ,Save, Screen

Capture, Storage, Tool Bar, Air Class etc , Android 9.0 or better , Internal Memory (32GB),(Hisi

811, Dual core A73+Dual core A53), DDR(4GB), Wi-Fi, Power Indicator, or higher, Screen

Share/Mira cast to Connect TAB/Mobile, Web Browser , 100-240V~, 50/60Hz, 20W(10W x 2) or

higher , ISO9001, ISO14001,ISO45001,

Portable USB Video Confrencing camera,PTZ Camera, 20X Optical Zoom, Digital Zoom: Up to 12X

Wide Viewing Angle up to 72.5 Degrees, RJ-45 Port, Quiet Motor with Servo Algorithm for PTZ

21 Control, Full HD 1080p signal output format with a high frame rate of 60 fps, HDMI, and USB 3.0 Nos. 2

synchronous video outputs

Digitally signed by AMIT

Executed No. of

USB: 2.0 (micro-B to Type A) ▪ Bluetooth 5.0, Class 1 (HFP/HSP/A2DP) ▪ NFC for easy pairin, Audio

Specifications ▪ OmniSound ® HD voice ▪ Speaker:

╶ Frequency response: 100Hz to 20,000Hz ╶ Volume: 90dB (SPL 0.5m) ▪ Microphones: ╶ 4 MEMS

microphones: 100Hz to 7,000Hz ╶ Pickup range: 20ft/6m

▪ Audio expansion: daisy chain connection (future release). ▪ Full Duplex▪ Acoustic Echo

Wireless Cancellation and Noise Suppression, Touch buttons: ╶ Answer call / Power

Mic ╶ End Call ╶ Bluetooth ╶ Volume Up / Down ╶ Mute

▪ LED Status Indicators ╶ Power status╶ Call status

╶ Bluetooth status ╶ Battery status ▪ Upgradable Software ▪ Upgradable Software, Integrated

Lithium Polymer Battery ╶ Call time up to 14 hour, Temperature range: 5°- 40°C ▪ Relative

humidity: 20 – 80% condensation-free

Active speaker pair of 35 watt, Transducers: LF: 135 mm (5.25 in) low frequency loudspeaker HF:

19 mm (.75 in) Polycarbonate dome tweeter Frequency Range: 80 Hz - 20 kHz Amplifier Power: 35

Watts per channel Maximum SPL Per Pair: 115 dB Crossover Frequency: 4.2 kHz Input Sensitivity:

+4 dBu XLR 1/4"; 0 dBu RCA Signal Input Connectors (x2): Balanced Neutrik* Combo XLR 1/4" TRS;

Unbalanced RCA Power Requirements: 19 VDC / 3.42 A - use only supplied power supply

Headphone Jack: 3.5 mm (1/8") Dimensions: 235 x 159 x 143 mm (9.3 x 6.3 x 5.6 in). tudio quality

transducers for accuracy, and rich bass response: 80 Hz - 20 Khz 35 watt per-channel power

amplifier and high sensitivity drivers produce exceptional output: 115 DB max SPL per pair

Active Balanced XLR, ¼”, and unbalanced RCA inputs allow connection to a range of signal sources Stereo

23 headphone jack allows monitoring using headphones Ergonomic, side-mounted volume control - Pair 2

simultaneously controls left and right speakers High frequency adjust control - allows the user to

contour HF response to application requirements Magnetically-shielded transducers for use near

CRT monitors and magnetically sensitive equipment Internal peak limiter and overload protection

circuit - protects the system from damage caused by continuous over-driving Wall-mount capable

using optional MTC-2P mounting kit Included snap-on pedestals optimize listening angle for

desktop applications including cabling etc as per instruction of Engineer In charge

Conference Room 9 Pax

Digitally signed by AMIT

Executed No. of

75" smart 4K LED Display,Native Resolution 3840 x 2160 (UHD), Brightness Minimum 390cd/m2,

Inputs HDMI-3,USB(3.0)-3,USB-(2,0)-2,OPS Slot-1,RGB-1, LAN-1,SPDIF-1 or Higher, Output

Audio-1( Audio out to connect additional Speakers if required) , Built in Touch type IR spread /P

Cap/Incell/Inglass, Touch Accuracy ±1.5mm or less, Operating System Support Windows

7/8/10/Windows XP/Linux/Mac/Android (Windows XP/Linux/Mac Support one point touch) ,

Multi touch point Min 20 Points or Higher, White Board ,Writing, Pen, Palm Eraser ,Save, Screen

Capture, Storage, Tool Bar, Air Class etc , Android 9.0 or better , Internal Memory (32GB),(Hisi

811, Dual core A73+Dual core A53), DDR(4GB), Wi-Fi, Power Indicator, or higher, Screen

Share/Mira cast to Connect TAB/Mobile, Web Browser , 100-240V~, 50/60Hz, 20W(10W x 2) or

higher , ISO9001, ISO14001,ISO45001,

Portable USB Video Confrencing camera,PTZ Camera, 20X Optical Zoom, Digital Zoom: Up to 12X

USB Wide Viewing Angle up to 72.5 Degrees, RJ-45 Port, Quiet Motor with Servo Algorithm for PTZ

Camera Control, Full HD 1080p signal output format with a high frame rate of 60 fps, HDMI, and USB 3.0

synchronous video outputs

USB: 2.0 (micro-B to Type A) ▪ Bluetooth 5.0, Class 1 (HFP/HSP/A2DP) ▪ NFC for easy pairin, Audio

Specifications ▪ OmniSound ® HD voice ▪ Speaker: ╶ Frequency response: 100Hz to 20,000Hz ╶

Volume: 90dB (SPL 0.5m) ▪ Microphones: ╶ 4 MEMS microphones: 100Hz to 7,000Hz ╶ Pickup

range: 20ft/6m ▪ Audio expansion: daisy chain connection (future release). ▪ Full Duplex▪ Acoustic

Wireless Echo Cancellation and Noise Suppression, Touch buttons: ╶ Answer call / Power╶ End Call ╶

26 Bluetooth ╶ Volume Up / Down ╶ Mute ▪ LED Status Indicators ╶ Power status╶ Call status ╶ Nos. 1

Bluetooth status ╶ Battery status ▪ Upgradable Software ▪ Upgradable Software, Integrated

Lithium Polymer Battery ╶ Call time up to 14 hour, Temperature range: 5°- 40°C ▪ Relative

humidity: 20 – 80% condensation-free

Digitally signed by AMIT

Executed No. of

Active speaker pair of 35 watt, Transducers: LF: 135 mm (5.25 in) low frequency loudspeaker HF:

19 mm (.75 in) Polycarbonate dome tweeter Frequency Range: 80 Hz - 20 kHz Amplifier Power: 35

Watts per channel Maximum SPL Per Pair: 115 dB Crossover Frequency: 4.2 kHz

Input Sensitivity: +4 dBu XLR 1/4"; 0 dBu RCA

Signal Input Connectors (x2): Balanced Neutrik* Combo XLR 1/4" TRS; Unbalanced RCA Power

Requirements: 19 VDC / 3.42 A - use only supplied power supply

Headphone Jack: 3.5 mm (1/8") Dimensions: 235 x 159 x 143 mm (9.3 x 6.3 x 5.6 in). tudio quality

transducers for accuracy, and rich bass response: 80 Hz - 20 Khz

Active 35 watt per-channel power amplifier and high sensitivity drivers produce exceptional output: 115

27 DB max SPL per pair Balanced XLR, ¼”, and unbalanced RCA inputs allow connection to a range of Pair 1

signal sources Stereo headphone jack allows monitoring using headphones Ergonomic, side-

mounted volume control - simultaneously controls left and right speakers High frequency adjust

control - allows the user to contour HF response to application requirements

Magnetically-shielded transducers for use near CRT monitors and magnetically sensitive

equipment Internal peak limiter and overload protection circuit - protects the system from

damage caused by continuous over-driving

Wall-mount capable using optional MTC-2P mounting kit

Included snap-on pedestals optimize listening angle

for desktop applications including cabling etc as per instruction of Engineer In charge

55" smart 4K LED Display,Native Resolution 3840 x 2160, Brightness Minimum 390cd/m2, Inputs

HDMI-3,USB(3.0)-3,USB-(2,0)-2,OPS Slot-1,RGB-1, LAN-1,SPDIF-1 or Higher, Output Audio-1(

Audio out to connect additional Speakers if required) , Built in Touch type IR spread /P

Cap/Incell/Inglass, Touch Accuracy ±1.5mm or less, Operating System Support Windows

7/8/10/Windows XP/Linux/Mac/Android (Windows XP/Linux/Mac Support one point touch) ,

Multi touch point Min 20 Points or Higher, White Board ,Writing, Pen, Palm Eraser ,Save, Screen

Capture, Storage, Tool Bar, Air Class etc , Android 9.0 or better , Internal Memory (32GB),(Hisi

811, Dual core A73+Dual core A53), DDR(4GB), Wi-Fi, Power Indicator, or higher, Screen

Share/Mira cast to Connect TAB/Mobile, Web Browser , 100-240V~, 50/60Hz, 20W(10W x 2) or

higher , ISO9001, ISO14001,ISO45001,

Digitally signed by AMIT

Executed No. of

55" smart 4K LED Display,Native Resolution 3840 x 2160, Brightness Minimum 390cd/m2, Inputs

HDMI-3,USB(3.0)-3,USB-(2,0)-2,OPS Slot-1,RGB-1, LAN-1,SPDIF-1 or Higher, Output Audio-1(

Audio out to connect additional Speakers if required) , Built in Touch type IR spread /P

Cap/Incell/Inglass, Touch Accuracy ±1.5mm or less, Operating System Support Windows

7/8/10/Windows XP/Linux/Mac/Android (Windows XP/Linux/Mac Support one point touch) ,

29 55" Multi touch point Min 20 Points or Higher, White Board ,Writing, Pen, Palm Eraser ,Save, Screen Nos. 4

Capture, Storage, Tool Bar, Air Class etc , Android 9.0 or better , Internal Memory (32GB),(Hisi

811, Dual core A73+Dual core A53), DDR(4GB), Wi-Fi, Power Indicator, or higher, Screen

Share/Mira cast to Connect TAB/Mobile, Web Browser , 100-240V~, 50/60Hz, 20W(10W x 2) or

higher , ISO9001, ISO14001,ISO45001

Portable USB Video Confrencing camera,PTZ Camera, 20X Optical Zoom, Digital Zoom: Up to 12X

Wide Viewing Angle up to 72.5 Degrees, RJ-45 Port, Quiet Motor with Servo Algorithm for PTZ

30 Control, Full HD 1080p signal output format with a high frame rate of 60 fps, HDMI, and USB 3.0 Nos. 4

synchronous video outputs

USB: 2.0 (micro-B to Type A) ▪ Bluetooth 5.0, Class 1 (HFP/HSP/A2DP) ▪ NFC for easy pairin, Audio

Specifications ▪ OmniSound ® HD voice ▪ Speaker:

╶ Frequency response: 100Hz to 20,000Hz ╶ Volume: 90dB (SPL 0.5m) ▪ Microphones: ╶ 4 MEMS

microphones: 100Hz to 7,000Hz ╶ Pickup range: 20ft/6m

▪ Audio expansion: daisy chain connection (future release). ▪ Full Duplex▪ Acoustic Echo

Wireless Cancellation and Noise Suppression, Touch buttons: ╶ Answer call / Power

▪ LED Status Indicators ╶ Power status╶ Call status

╶ Bluetooth status ╶ Battery status ▪ Upgradable Software ▪ Upgradable Software, Integrated

Lithium Polymer Battery ╶ Call time up to 14 hour, Temperature range: 5°- 40°C ▪ Relative

humidity: 20 – 80% condensation-free

Digitally signed by AMIT

Executed No. of

Active speaker pair of 35 watt, Transducers: LF: 135 mm (5.25 in) low frequency loudspeaker HF:

19 mm (.75 in) Polycarbonate dome tweeter Frequency Range: 80 Hz - 20 kHz Amplifier Power: 35

Watts per channel Maximum SPL Per Pair: 115 dB Crossover Frequency: 4.2 kHz

Input Sensitivity: +4 dBu XLR 1/4"; 0 dBu RCA

Signal Input Connectors (x2): Balanced Neutrik* Combo XLR 1/4" TRS; Unbalanced RCA Power

Requirements: 19 VDC / 3.42 A - use only supplied power supply

Headphone Jack: 3.5 mm (1/8") Dimensions: 235 x 159 x 143 mm (9.3 x 6.3 x 5.6 in). tudio quality

transducers for accuracy, and rich bass response: 80 Hz - 20 Khz

Active 35 watt per-channel power amplifier and high sensitivity drivers produce exceptional output: 115

32 DB max SPL per pair Balanced XLR, ¼”, and unbalanced RCA inputs allow connection to a range of Pair 4

signal sources Stereo headphone jack allows monitoring using headphones Ergonomic, side-

mounted volume control - simultaneously controls left and right speakers High frequency adjust

control - allows the user to contour HF response to application requirements

Magnetically-shielded transducers for use near CRT monitors and magnetically sensitive

equipment Internal peak limiter and overload protection circuit - protects the system from

damage caused by continuous over-driving

Wall-mount capable using optional MTC-2P mounting kit

Included snap-on pedestals optimize listening angle

for desktop applications including cabling etc as per instruction of Engineer In charge

55" smart 4K LED Display,Native Resolution 3840 x 2160, Brightness Minimum 390cd/m2, Inputs

HDMI-3,USB(3.0)-3,USB-(2,0)-2,OPS Slot-1,RGB-1, LAN-1,SPDIF-1 or Higher, Output Audio-1(

Audio out to connect additional Speakers if required) , Built in Touch type IR spread /P

Cap/Incell/Inglass, Touch Accuracy ±1.5mm or less, Operating System Support Windows

7/8/10/Windows XP/Linux/Mac/Android (Windows XP/Linux/Mac Support one point touch) ,

33 55" Multi touch point Min 20 Points or Higher, White Board ,Writing, Pen, Palm Eraser ,Save, Screen Nos 5

Capture, Storage, Tool Bar, Air Class etc , Android 9.0 or better , Internal Memory (32GB),(Hisi

811, Dual core A73+Dual core A53), DDR(4GB), Wi-Fi, Power Indicator, or higher, Screen

Share/Mira cast to Connect TAB/Mobile, Web Browser , 100-240V~, 50/60Hz, 20W(10W x 2) or

higher , ISO9001, ISO14001,ISO45001,

VC for ED Room cabins:

34 Portable USB Video Confrencing, PTZ Camera, 12x auto focus zoom lens, 360 continuous Nos 5

rotation, high-speed pan and tilt operations.

Active Speakers for ED Room:

Active speaker pair of

Frequency Range: 80 Hz - 20 kHz

Amplifier Power: 35 Watts per channel Maximum

SPL Per Pair: 115 dB Crossover Frequency: 4.2 kHz

Digitally signed by AMIT

Executed No. of

Open Pluggable Specification(OPS):

Intel Core i5 11th Generation, 8GB RAM, 256GB SSD, 1000 mbps gigaLAN, 450 mbps WI-FI,

bluetooth Windows 10 Pro License Pre-Loaded, HDMI 2.0, Mini DP, USB 2.0 x 2 USB 3.0 x

2, USB C TYPE X1, Audio In, Audio Out

E CAMC of Gass Supression, FF & PA Works:

Gas Suppression System

having following Equipments:

Seamless Novec 1230 Cylinder and Valve Assembly, 34

Ltrs. Capacity - 2 Nos.

FM 200 - 60 Kgs

Electrical Actuator for Master Cylinder - 2 Nos.

Discharge Hose - 2 Nos.

Cylinder Low Pressure Switch - 2 Nos.

Nozzles, 360 Deg / 180 Deg Throw - 4 Nos.

Suppression System Piping - 1 Lot

Gas Release Switch/Module - 2 Nos.

Abort Switch - 2 Nos.

Gas Release Panel - 2 Nos.

Make: Ravel/ADN (Including Refilling of Gas per the requirement of complete operation of system)

Fire Fighting System

CAMC of Fire Fighting System having Following Equipments:

Hydrants - 1 Lot

Sprinklers - 1 Lot

Fire Piping and Accessories - 1 Lot

b) Mechanical Foam gas cartridge type. 9 Kg capacity (IS:15683).

c) ABC dry powder stored pressure type 6 kg capacity (IS:15683).

(Including Refilling of cylinders as per the requirement of complete operation of system)

Fire Alarm and PA System

Digitally signed by AMIT

Executed No. of

CAMC of Fire Alarm and PA System having Following Equipments:

Intelligent analog addressable photothermal detector - 150 Nos.

Response Indicator - 19 Nos.

Addressable fire control module - 4 Nos.

Addressable horn cum strobe - 4 Nos.

Addressable manual call point - 4 Nos.

1.5/3/6W ceiling speaker - 86 Nos.

Digital audio amplifier 75 Watt - 3 Nos.

Voice command keypad 6 zone - 1 No.

Loop Card capacity of 159 detectors For BMS Fire integration - 1 No.

Interface Card for BMS fire integration - 1 No.

Repeater panel - 1 No.

F CAMC of Smart Rack:

1 i-CSR Two smart Racks Solution with 10kW Cooling & 10kW UPS (N+N) Set 1

Server / Network Rack - 800W x 2000H (42U) x 1200D, 100H Base Plinth with A.V pad, Front Glass

Door, Rear Split Plain Door, High Density Vertical Cable Manager & Accessories. 2 nos;

1U Horizontal Cable Manager with PVC channel type 4

Copper Earth Rail 15x5 with screws and insulators 2

Vertical PDU - BASIC & UPS DBBasic Vertical PDU, 30A, 1Ф, 250 VAC, Vertical Rack PDU with “C”

curve 32A single pole MCB with safety guard, power indicator, 16nos of IEC-320-C13 Sockets, 6nos

of IEC-320-C19 Sockets, 2nos of EMO-71-1 6/13Amp Universal Sockets, 6 sq.mm 3 core 4.5 meter 4

cable with NEMA Twist Lock Plug (30A ENP-LD6-30) & Mounting brackets hardware for vertical

UPS DB, 1Phase 32A PDU, with NEMA socket 1 no. & C13 socket 2 nos.,with 32A MCB & PG-16

cable gland,Colour:RAL 9005

In-Rack Cooling System - 10kW (N+N)-

Cooling Unit Module (DX Type, Digital Scroll) - 10kW with Redundancy (N+N)

- Indoor Unit Module with EC Fans

Low Side Works for Air-Condition System (15 mtrs dist b/n indoor & outdoor for each 10kW

Environmental Monitoring & Security System

Digitally signed by AMIT

Executed No. of

Environmental Monitoring System with water leaks detection system, temperature & humidity

sensor, Somke Sensor, door sensor & alarm beacon

Biometric Access Control System for Front Rack Door with EM Locks, cabling, bkts etc. 2

Standalone Ultrasonic Rodent Repeller 2

Automatic Door Opening system (For Front Doors) 2

Rack Based Fire Detection & Extinguishing System with FITECH 1230 / FK-5-1-12 Suppression

(2 Rack System)

Electrical Distribution Boards & Cabling Works

Raw Power DB : 19" Rack Mountable Raw Power Distribution Panel with TVSS, Incomer breaker,

Outgoing breakers for Cooling Units, UPS Units, Rodent Repellant, etc.

Cable Trough of size : 300W x 50H mm with Cover Lid & necessary accessories for fixing. 20 mtr

UPS with Battery Bank & STS

10 KVA /10 KW Rack Mount UPS with 1 Phase Input and 1 Phase Output Online UPS ( Model :

External Battery Rack with 15min back-up on full load with all accessories & cables. 2

16A Rack Mountable (1U) STS 16 (Source Transfer Switch) 1

as approved by EIC. Make- Rittal

2 STATIC SWITCH MODULE

Static switch module with microprocessor based control and suitable for linear and non linear load

at particulars distribution board of critical load in event of short circuit overload or any other fatal

condition with built-in Technical Protections like short circuit, Overload, High/Low Voltage cutoff

protection of load from source inclusive of Bypass facility Static Bypass Module is activated during

malfunctioning conditions of load like :-

• Short Circuit

• Bypassing of particular load if required

• Resulting in non tripping of main UPS unit • Input Voltage (320-460VAC) 3 phase

• Input frequency 50Hz Indication & Monitoring

• UPS Supply on/source I

• Load on UPS supply/source I

• Main supply on/source II

• Load on mains supply/Bypass

Digitally signed by AMIT

Executed No. of

• Bypass Switch on

• Bypass Switch off

complete as required and as per specifications.

Capacity: 63A 3 Phase

G CAMC of CCTV:

5MP IR IP H.265 Vandal Proof Dome camera with 2.8 to 12mm Motorized Lens,Smart IR, up to 30M IR

distance,Up to 120 dB WDR (Wide Dynamic Range),3D DNR (Digital Noise Reduction),H.265+, H.265, H.264,

MJPEG,Corridor mode, Triple streams,3-Axis, IP67, IK10 Vandal Resistant,Colour: 0.005Lux (F1.4, AGC ON), 0

Lux with IR,Video Compression H.265+, H.265, H.264, MJPEG,Behavior Detection Intrusion, Crossing line,

1 Motion detection, Object left, Missing object,Intelligent Identification Face detection, Defocus, Scene Nos 19.00

Change,PoE (IEEE802.3 af) Power consumption: Max 7.2W,Edge Storage Micro SD Card, Up to 256GB, ANR

Support,Working Environment -40°C ~ +60°C, Humidity ≤ 90% RH(Non-condensing),Compatible Integration

ONVIF (Profile S/G), API.

16Ch Embedded Network Video Recorder with 4 Sata Supports 1 × RJ45 1000M ,4K Cameras, HDMI, VGA,

RAID, Redundant power supply, Smart Analytics and ONVIF

SSD Hard Disk Drive 8TB, 24/7 surveillance category Only complete etc as required.etc.all complete. 11,088.00 12.00 1,33,056.00

55" Flat Screen HD led (24X7) with Interfaces include HDMI, DVI, D-sub, Component and Composite input as

4 well as RS-232C and RJ45 for extensive connectivity, remote control and wall mount unit / floor stand Nos 1.00

complete with making connections etc complete as reqd.

4Ch Embedded Network Video Recorder with 2 Sata Supports 1 × RJ45 1000M ,4K Cameras, HDMI, VGA,

5 RAID, Redundant power supply, Smart Analytics, Nos 1.00

32" Flat Screen HD led (24X7) with Interfaces include HDMI, DVI, D-sub, Component and Composite input as

6 well as RS-232C and RJ45 for extensive connectivity, remote control and wall mount unit / floor stand Nos 1.00

complete with making connections etc complete as reqd.

H CAMC of EPABX

Digitally signed by AMIT

Executed No. of

Server based Communication System with all the required Software licenses and Hardware

- IP-PBX/IP Telephony Communications Server: The IP Telephony Solution shall support the

following Services - Voice, Video, IM, Presence and Audio Conference The Solution should

be built on Active-Active Redundant Servers The IP Telephony Solution should support

H.323 and SIP The Solution should support the following Trunks - FXO, E1 PRI and SIP The

IP Telephony solution should incorporate all licenses for the Phones and Trunks Solution

1 should support 80 Extensions from Day 1 with future scalabilityupto 5000 users. Licenses Nos 1

for all Phones supplied should be provisioned on Day1 Solution should support Hard IP

Phones, Softphones, Video Phones, 50 Analog Extensions with necessary Licenses, Rack

mount architecture, complete as required and as per technical specifications.

Executive Level IP Phone with Color display – 3.7 inches x 2.1 inches (9.5 cm x 5.4 cm)-

Diagonal width: 4.3 inches (11 cm), Touch Screen display, 4-position adjustable tilt display,

Permanently-labeled feature buttons:, speaker, mute, headset, contacts, home, history,

message, phone, forwarding, volume (separate volume levels in handset, speaker, ringer,

and headset), Red LEDs on speaker, mute, headset, message and history, 24 administrative

buttons, Wideband speakerphone 0-5 Softkeys, Ergonomic hearing aid compatible,

handset supporting TTD acoustic coupler, Bluetooth and DECT headset support with

2 adapter, Message waiting indicator, Ethernet (10/100/1000) line interface, Secondary Nos 32

Ethernet (10/100/1000)line interface, Optional IEEE PoE 802.3af adapter registers as class

2 device, SIP protocol, H.323 protocol support, Standards-based codec support: G.711,

G.726, G.729A/B, G722 , Supports the following languages: Arabic, Brazilian Portuguese, 34,523.00 12.00 4,14,276.00

Simplified, Chinese, Dutch, English, Canadian,French, Parisian French, German,Hebrew,

Italian, Japanese (Kanji,Hiragana and Katakana), Korean, Latin American Spanish, Castilian

Spanish, and Russian. Includ Licence.

Digitally signed by AMIT

Executed No. of

2.8” (diagonal) color display—320 x 240 pixels, Multiple line phone with four red / green

line / feature indicators around display, 4 Context sensitive soft keys, Hard buttons for

phone, messages, contacts, history, home, navigation cluster, headset, speaker, volume,

mute, LEDs for speaker, mute, headset, essage, history, Wideband audio in handset and

wired headset, Full duplex speakerphone & handset, Ergonomic hearing aid compatible

handset supports TTD acoustic coupler, Message waiting indicator, Mute key with optional

mute alerting, IC call alerting with 360-degree visibility, Dual-position stand, optional wall-

mount stand, Gigabit Ethernet (10 / 100 / 1000) line interface, Second Ethernet interface

3 10 / 100 / 1000 Mbps, PoE Class (IEEE 802.3af) registers as class 1 device and supports Nos 53

802.3az, Optional AC to 5 volt power supply • SIP protocol support, Standards-based codec

support: G.722, Opus, Configurable via Web interface, Support for HTTPS, TLS and SRTP for

encryption, Recent Call Log (100 entries), Zero touch deployment via Device Enrollment

Services Support, Supports the following languages: Dutch, English (UK & US), French,

(Canada), French (France), German, Italian, Japanese, Portuguese (Brazil), Simplified

Chinese, Spanish (Latin America), Spanish (Spain),Traditional Chinese, Includ Licence.

Additional Items:

CAMC of Biometric Attendance system with software:

Supported by rugged fingerprint sensors, This time attendance machine qualifies IP65

2 standards, Report generation on employee attendance, Centralized Data Collection, Nos 1

Personnel-wise attendance tracking and monitoring.

Power Charger (7.2 Kw x 1 No)

Ziptron (3 Nos)

Wall Mounting Unit 7.2 KW

Digitally signed by AMIT

CAMC/AMC ESTIMATE FOR HVAC/VRV, FIRE ALARM & PA, CCTV, EPABX, ELECTRICAL, IT, AV etc. ITEMS FOR IREDA OFFICE, IBC, EKN, 7th FLOOR, TOWER-2

Executed No. of

A CAMC of HVAC/VRV:

Modular type Variable Refrigerant Flow/Variable Refrigerant Volume air cooled Outdoor units suitable for

cooling and heating, having all hermetically sealed inverter type Scroll Compressor(s), minimum two

compressors for above 14 HP modules, microprocessor based Controller, top discharge type condensing

unit(s), with R 410 A Refrigerant, vibration isolators, with suitable foundation etc. complete as required. The

unit shall deliver the rated capacity at AHRI Conditions and work even at 50°C ambient temperature without

1 tripping. The unit shall be suitable to work on 400V +/- 10%, 3 Phase, 50Hz AC power supply. The unit shall per HP 40.00

be filled with first charge of the refrigerant and ready for use as required. The COP at AHRI conditions shall

not be less than 3.1 and IEER not less than 6.5 .

4-way flow VRV/VRF Cassette Type Indoor ceiling mounted unit equipped with synthetic washable media pre-

filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX

Copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration

isolation, cord less remote control etc., suitable for operation on single phase 230 V ± 10%, 50Hz AC supply,

complete, as required. The unit shall have automatic force shut down provision in case of fire on receiving

signal from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB

and 19 Degree C

WB temperature.

Inverter type High Wall Indoor Unit with Stablizer, 3 star, including cost of copper piping (upyo 15

mtr, drain pipe wire and remote)

3 High Wall - 2 Tr (Inverter Compressor with stablizer) Nos 2

VAV BOX (WITH INTEGRAL SOUND ATTENUATOR)

Pressure independent rectangular VAV unit with integral sound attenuator made of 22G GI sheet

casing length 900mm consisting of 25mm thick 48kg/m3 density fiber glass wool covered with

4 tissue paper ,elliptical volume control damper , calibrated differential pressure sensor (DPT

sensors) at inlet complete with digital Thermostat.( All VAV shall be factory calibrated ).

Variable Frequency Drive (VFD)

380-400 VAC, IP-54 Chassis, RFI class A1 (C2), No brake chopper.

Digitally signed by AMIT

Executed No. of

B CAMC of Electrical:

The following sheet steel cubicle type panels fabricated from 1.6mm thick CRCA sheet, dust and vermin

proof, indoor type TPN Panels with hinged lockable doors fabricated from 2mm thick CRCA sheet, suitable

for 415V, 3 phase 4 wire 50Hz AC supply with rear access for cable alley and with segregated bus-bar

1 chamber with tinned aluminium bus bar and including supplying and fixing following switchgears, meters Each 1 3,015.10 12.00 36,181.20

and accessories, inter-connections, bonding to earth, powder coated painting and marking as specified.

Switch boards complete as per schematic diagram:

Type of construction: Form 3

IP classification: 42

The LT PANEL shall be electrically inter-locked as shown in Schematic diagram and as detailed in the

Colour: Gray Powder Coated, as per approved sample.

1 nos, 250 Amps. 4 pole MCCB , i.e four pole Moulded Case Circuit Breaker of fault breaking capacity 25 KA

(ICS=ICU up to 433 V) complete in all respect

TPN aluminum bus bars of minimum of 320 Amps capacity with heat shrinkable colored sleeves and I/C

DMC/SMC bus bars supports at required intervals complete for cross section, size supports & their spacing

etc. for withstanding fault level of 25 MVA for 1 Sec.

(a) 63 Amps, TPN, MCB -6 Nos.

(b) 40 Amps, TPN, MCB - 6 nos

(c ) 125 Amps TPN MCB - 4 nos

Panel complete as above

The following sheet steel cubicle type panels fabricated from 1.6mm thick CRCA sheet, dust and vermin

proof, indoor type TPN Panels with hinged lockable doors fabricated from 2mm thick CRCA sheet, suitable

for 415V, 3 phase 4 wire 50Hz AC supply with rear access for cable alley and with segregated bus-bar

2 chamber with tinned aluminium bus bar and including supplying and fixing following switchgears, meters Each 1 2,563.00 12.00 30,756.00

and accessories, inter-connections, bonding to earth, powder coated painting and marking as specified.

Switch boards complete as per schematic diagram:

Type of construction: Form 3

IP classification: 42

The LT PANEL shall be electrically inter-locked as shown in Schematic diagram and as detailed in the

Colour: Gray Powder Coated, as per approved sample.

Two (2) nos, 125 Amps. 4 pole MCCB , i.e four pole Moulded Case Circuit Breaker of fault breaking capacity

25 KA (ICS=ICU up to 433 V) complete in all respect

TPN aluminum bus bars of minimum of 400 Amps capacity with heat shrinkable colored sleeves and I/C

DMC/SMC bus bars supports at required intervals complete for cross section, size supports & their spacing

etc. for withstanding fault level of 25 MVA for 1 Sec.

Digitally signed by AMIT

Executed No. of

1 Nos. 250A, 4P, MCCB (25kA) with phase indicating lamp protected with 2A, SP, MCB's along with E/M

(a) 63 Amps, TPN, MCB - 2 nos

(b ) 40 Amps, TPN MCB - 6 nos

Panel complete as above

High Efficient 60kVA/60 KW Model IGBT Rectifier & IGBT Inverter, Modular Fault Tolerant designFailure in

any one of the module the others keeps supplying to the load without interruption. Approved Make, 12V

VRLA Batteries, 65 AH or saiuitable for 30 minutes backup. Exide (40 nos on each bank) Make Exide,

3 Accessories ( Cabling between UPS and the Battery upto 10 Mtr distance for each UPS considering cable NO. 2 45,513.60 12.00 5,46,163.20

Routing,Battery Rack and Battery Interlinks, lugs etc ) DC MCCB between UPS and Battery complete in all

respect as per the directions of engineer in charge. UPS shall produce 30 minutes backup.

C CAMC of IT Active Works:

24-Port Layer 3 Stackable Managed Gigabit Switch, 20 x 10/100/1000BASE-T ports With 4 x Combo

10/100/1000BASE-T/SFP ports, 4 x 10G SFP+ ports, Switch Resource Management (SRM) for flexible

management of system resources, Redundant Power Supply (RPS) support, MPLS L2VPM/L3 VPN support,

Full L3 routing protocol support including OSPF, BGP, and ISIS for IPv4/IPv6. As Approved by NSL Incharge.

Access Switch of 48 x 1G POE+, 4 x SFP+ , 370W PoE, Switching Capacity of switch is of 176 Gbps having

Forwarding performance (64-byte packet size): 130 Mpps, Secure Shell (SSH), RADIUS, TACACS + DRAM 2GB

, Flash 2GB , 10K IPv4 Routes ,1K multicast Routes ,16K MAC address , 16K flow entries L3 Protcols like OSPF ,

PBR, MACsec, PIM , QOS from day-1 , As Approved by NSL Incharge.

48 port 10/100/1000 Base T Switch with 4 x 10G SFP+ ports,The Switch should have 16K MAC address,

Should have RJ-45 console port should support MSTP and DUAL configuration, Should support Static 83,053.30 12.00 9,96,639.60

Route Entry: IPv4 124; IPv6 50 , Should support IP-MAC- Port Binding strictly management network devices

3 preventing illegal access and the Man-in- the-middle attack, Should support Asymmetric VLAN, Auto Voice Nos. 6.00

VLAN, Should support Cable diagnostics, Time-based PoE: PoE ports can be turned on/off by port or

system through schedule, Operating Temperature -5 to 50°C (23 to 122°F). As Approved by NSL Incharge.

Wi-Fi standard, IEEE’s new 802.11ac Wave 2 specification, and meets the growing requirements of wireless

networks by delivering a better user experience. The 1830 Series extends support to a new generation of Wi-

4 Fi clients, such as smartphones, tablets, and high-performance laptops that have integrated 802.11ac Wave Nos. 30.00

1 or Wave 2 support.

Modules 10G - 30 Nos. & LC- LC multimode OFC type patch cord - 10 Nos.

C.1 AMC of Passive Works:

Annual Maintenance Contract of Passive Components System having Following Equipments:

UTP Components for Data - 1 Lot

200 Pair MDF Box -1 Lot

UTP Components for Wifi - 1 Lot

UTP Components for CCTV and Access Control - 1 Lot

Digitally signed by AMIT

Executed No. of

D CAMC of AV Works:

98" smart 4K LED Display,Native Resolution 3840 x 2160 (UHD), Brightness Minimum 490cd/m2,

Inputs HDMI-3,USB(3.0)-3,USB-(2,0)-2,OPS Slot-1,RGB-1, LAN-1,SPDIF-1 or Higher, Output

Audio-1( Audio out to connect additional Speakers if required) , Built in Touch type IR spread /P

Cap/Incell/Inglass, Touch Accuracy ±1.5mm or less, Operating System Support Windows

98" main 7/8/10/Windows XP/Linux/Mac/Android (Windows XP/Linux/Mac Support one point touch) , Multi

LED touch point Min 20 Points or Higher, White Board ,Writing, Pen, Palm Eraser ,Save, Screen

display Capture, Storage, Tool Bar, Air Class etc , Android 9.0 or better , Internal Memory (32GB),(Hisi

(1-CMD 811, Dual core A73+Dual core A53), DDR(4GB), Wi-Fi, Power Indicator, or higher, Screen

1-Board Share/Mira cast to Connect TAB/Mobile, Web Browser , 100-240V~, 50/60Hz, 32W(16W x 2) or

Room) higher , ISO9001, ISO14001,ISO45001,

The display should be a smart screen and touch enabled alongwith stylus/pen. The display should

also have provision for OPS PC.

55" smart 4K LED Display,Native Resolution 3840 x 2160, Brightness Minimum 390cd/m2, Inputs

HDMI-3,USB(3.0)-3,USB-(2,0)-2,OPS Slot-1,RGB-1, LAN-1,SPDIF-1 or Higher, Output Audio-1(

Audio out to connect additional Speakers if required) , Built in Touch type IR spread /P

Cap/Incell/Inglass, Touch Accuracy ±1.5mm or less, Operating System Support Windows

7/8/10/Windows XP/Linux/Mac/Android (Windows XP/Linux/Mac Support one point touch) , Multi

touch point Min 20 Points or Higher, White Board ,Writing, Pen, Palm Eraser ,Save, Screen

Capture, Storage, Tool Bar, Air Class etc , Android 9.0 or better , Internal Memory (32GB),(Hisi

811, Dual core A73+Dual core A53), DDR(4GB), Wi-Fi, Power Indicator, or higher, Screen

Share/Mira cast to Connect TAB/Mobile, Web Browser , 100-240V~, 50/60Hz, 20W(10W x 2) or

higher , ISO9001, ISO14001,ISO45001,

The display should be a smart screen and touch enabled alongwith stylus/pen. The display should

also have provision for OPS PC.

Portable USB Video Confrencing camera,PTZ Camera, 20X Optical Zoom, Digital Zoom: Up to 12X

Wide Viewing Angle up to 72.5 Degrees, RJ-45 Port, Quiet Motor with Servo Algorithm for PTZ

USB Control, Full HD 1080p signal output format with a high frame rate of 60 fps, HDMI, and USB 3.0

Camera synchronous video outputs

Wireless digital boundary layer Microphone with 18 or more channel, RF output 80mW or more,

Cardioid pickup pattern, Frequency range : 1880 to 1930 MHz, Connectivity : RJ-45, 256-bit AES

4 MICS Encryption (specifications includes single microphone set of transmitter and receiver) etc and Nos. 14

complete as required.

wireless digital microphone charger, charging capacity : 2 or more simultaneously with lighting

Charger indication, Qi charging, Should be from same OEM as of wireless mic etc and complet required as

base per specifications.

Digitally signed by AMIT

Executed No. of

Digital signal processor with minimum 14no. Or more Mic / line input with phantom power and

AEC and 8 or more line output, at least 2 channel of USB input and output for software Video

Conferencing,, Should have sampline rate of 48kHz or better, Should be expandable for port

expansion. 64x64 or more Dante Input for Digital audio transfer as per need,should support

Control with App via iOS and Android devices, or any third-party control system, Shall have Built-

in filters, feedback suppression, AGC etc complete as required as per specifications

6.5" two-way coaxial thin edge ceiling loudspeaker, 100V transformer power taps : 24,12,6, watts,

Ceiling Conical dispersion : 145° or more, impedance : 8, low impedance RMS continous power : 30watts,

speakers frequency range : 50 Hz - 20 kHz or better, frequency response : 60Hz - 20KHz or better etc

complete required as per specifications.

Quad channel Amplifier, 4 X 120watt or more, THD+N (@ 1 kHz) : < 0.3%, Technology : Class-D,

Common mode rejection ratio : 70dB or better, Temperature controlled FAN, Switching mode

8 Amplifier power supply, should have Protection features like : DC Short circuit & Over heating & Over load & Nos. 1

Signal limiting etc, Built-in high pass filter and gain adjustment option etc complete required as per

specifications.

This HDMI Switcher/ Splitter 8x4 can connect 2HD signal sources with 8HD display terminals. It can

easily split 2-way HD signal sources to 8 HDTVs or projectors which support HD. It also can amplify

the HDMI signal. The two input HD signal sources can be switched freely. The HDMI Switch/Splitter

2x8 can support highest video resolution 3840x2160/30hz,Compatible with fully HDMI 1.3/1.4

Specification compliant. buffer HDMI signals at the same time, HDMI or DVI to HDMI cables used

9 Switcher for inputs and outputs. Included IR remote adapter for operational flexibility and easy control, no Nos. 1

manual clicking the select button needed. Support single high definition display and multiple

output HD signal sources, such as DVD Players, A/V receiversand Set Top Boxes, 360 Sky Box

Freesat Virgin Bluray Player DVD HDTV Projector Camcorder HTPC Laptop

65" smart 4K LED Display,Native Resolution 3840 x 2160, Brightness Minimum 390cd/m2, Inputs

HDMI-3,USB(3.0)-3,USB-(2,0)-2,OPS Slot-1,RGB-1, LAN-1,SPDIF-1 or Higher, Output Audio-1(

Audio out to connect additional Speakers if required) , Built in Touch type IR spread /P

Cap/Incell/Inglass, Touch Accuracy ±1.5mm or less, Operating System Support Windows

65" main 7/8/10/Windows XP/Linux/Mac/Android (Windows XP/Linux/Mac Support one point touch) , Multi

11 LED touch point Min 20 Points or Higher, White Board ,Writing, Pen, Palm Eraser ,Save, Screen Nos. 1

display Capture, Storage, Tool Bar, Air Class etc , Android 9.0 or better , Internal Memory (32GB),(Hisi

811, Dual core A73+Dual core A53), DDR(4GB), Wi-Fi, Power Indicator, or higher, Screen

Share/Mira cast to Connect TAB/Mobile, Web Browser , 100-240V~, 50/60Hz, 20W(10W x 2) or

higher , ISO9001, ISO14001,ISO45001.

Digitally signed by AMIT

Executed No. of

Portable USB Video Confrencing camera,PTZ Camera, 20X Optical Zoom, Digital Zoom: Up to 12X

Wide Viewing Angle up to 72.5 Degrees, RJ-45 Port, Quiet Motor with Servo Algorithm for PTZ

12 Control, Full HD 1080p signal output format with a high frame rate of 60 fps, HDMI, and USB 3.0 Nos. 2

synchronous video outputs

USB: 2.0 (micro-B to Type A) ▪ Bluetooth 5.0, Class 1 (HFP/HSP/A2DP) ▪ NFC for easy pairin, Audio

Specifications ▪ OmniSound ® HD voice ▪ Speaker:

╶ Frequency response: 100Hz to 20,000Hz ╶ Volume: 90dB (SPL 0.5m) ▪ Microphones: ╶ 4 MEMS

microphones: 100Hz to 7,000Hz ╶ Pickup range: 20ft/6m

▪ Audio expansion: daisy chain connection (future release). ▪ Full Duplex▪ Acoustic Echo

Wireless Cancellation and Noise Suppression, Touch buttons: ╶ Answer call / Power

Mic ╶ End Call ╶ Bluetooth ╶ Volume Up / Down ╶ Mute

▪ LED Status Indicators ╶ Power status╶ Call status

╶ Bluetooth status ╶ Battery status ▪ Upgradable Software ▪ Upgradable Software, Integrated

Lithium Polymer Battery ╶ Call time up to 14 hour, Temperature range: 5°- 40°C ▪ Relative

humidity: 20 – 80% condensation-free

Active speaker pair of 35 watt, Transducers: LF: 135 mm (5.25 in) low frequency loudspeaker HF:

19 mm (.75 in) Polycarbonate dome tweeter Frequency Range: 80 Hz - 20 kHz Amplifier Power: 35

Watts per channel Maximum SPL Per Pair: 115 dB Crossover Frequency: 4.2 kHz

Input Sensitivity: +4 dBu XLR 1/4"; 0 dBu RCA

Signal Input Connectors (x2): Balanced Neutrik* Combo XLR 1/4" TRS; Unbalanced RCA Power

Requirements: 19 VDC / 3.42 A - use only supplied power supply

Headphone Jack: 3.5 mm (1/8") Dimensions: 235 x 159 x 143 mm (9.3 x 6.3 x 5.6 in). tudio quality

transducers for accuracy, and rich bass response: 80 Hz - 20 Khz

35 watt per-channel power amplifier and high sensitivity drivers produce exceptional output: 115

DB max SPL per pair Balanced XLR, ¼”, and unbalanced RCA inputs allow connection to a range of

Active signal sources Stereo headphone jack allows monitoring using headphones Ergonomic, side-

speakers mounted volume control - simultaneously controls left and right speakers High frequency adjust

control - allows the user to contour HF response to application requirements

Magnetically-shielded transducers for use near CRT monitors and magnetically sensitive

equipment Internal peak limiter and overload protection circuit - protects the system from

damage caused by continuous over-driving

Wall-mount capable using optional MTC-2P mounting kit

Included snap-on pedestals optimize listening angle

for desktop applications including cabling etc as per instruction of Engineer In charge

Meeting Room 07 PAX (2 Nos)

Digitally signed by AMIT

Executed No. of

75" smart 4K LED Display,Native Resolution 3840 x 2160 (UHD), Brightness Minimum 390cd/m2,

Inputs HDMI-3,USB(3.0)-3,USB-(2,0)-2,OPS Slot-1,RGB-1, LAN-1,SPDIF-1 or Higher, Output

Audio-1( Audio out to connect additional Speakers if required) , Built in Touch type IR spread /P

Cap/Incell/Inglass, Touch Accuracy ±1.5mm or less, Operating System Support Windows

7/8/10/Windows XP/Linux/Mac/Android (Windows XP/Linux/Mac Support one point touch) , Multi

touch point Min 20 Points or Higher, White Board ,Writing, Pen, Palm Eraser ,Save, Screen

Capture, Storage, Tool Bar, Air Class etc , Android 9.0 or better , Internal Memory (32GB),(Hisi

811, Dual core A73+Dual core A53), DDR(4GB), Wi-Fi, Power Indicator, or higher, Screen

Share/Mira cast to Connect TAB/Mobile, Web Browser , 100-240V~, 50/60Hz, 20W(10W x 2) or

higher , ISO9001, ISO14001,ISO45001.

Portable USB Video Confrencing camera,PTZ Camera, 20X Optical Zoom, Digital Zoom: Up to 12X

Wide Viewing Angle up to 72.5 Degrees, RJ-45 Port, Quiet Motor with Servo Algorithm for PTZ

16 Control, Full HD 1080p signal output format with a high frame rate of 60 fps, HDMI, and USB 3.0 Nos. 1

synchronous video outputs

USB: 2.0 (micro-B to Type A) ▪ Bluetooth 5.0, Class 1 (HFP/HSP/A2DP) ▪ NFC for easy pairin, Audio

Specifications ▪ OmniSound ® HD voice ▪ Speaker:

╶ Frequency response: 100Hz to 20,000Hz ╶ Volume: 90dB (SPL 0.5m) ▪ Microphones: ╶ 4 MEMS

microphones: 100Hz to 7,000Hz ╶ Pickup range: 20ft/6m

▪ Audio expansion: daisy chain connection (future release). ▪ Full Duplex▪ Acoustic Echo

Wireless Cancellation and Noise Suppression, Touch buttons: ╶ Answer call / Power

Mic ╶ End Call ╶ Bluetooth ╶ Volume Up / Down ╶ Mute

▪ LED Status Indicators ╶ Power status╶ Call status

╶ Bluetooth status ╶ Battery status ▪ Upgradable Software ▪ Upgradable Software, Integrated

Lithium Polymer Battery ╶ Call time up to 14 hour, Temperature range: 5°- 40°C ▪ Relative

humidity: 20 – 80% condensation-free

Digitally signed by AMIT

Executed No. of

Active speaker pair of 35 watt, Transducers: LF: 135 mm (5.25 in) low frequency loudspeaker HF:

19 mm (.75 in) Polycarbonate dome tweeter Frequency Range: 80 Hz - 20 kHz Amplifier Power: 35

Watts per channel Maximum SPL Per Pair: 115 dB Crossover Frequency: 4.2 kHz

Input Sensitivity: +4 dBu XLR 1/4"; 0 dBu RCA

Signal Input Connectors (x2): Balanced Neutrik* Combo XLR 1/4" TRS; Unbalanced RCA Power

Requirements: 19 VDC / 3.42 A - use only supplied power supply

Headphone Jack: 3.5 mm (1/8") Dimensions: 235 x 159 x 143 mm (9.3 x 6.3 x 5.6 in). tudio quality

transducers for accuracy, and rich bass response: 80 Hz - 20 Khz

35 watt per-channel power amplifier and high sensitivity drivers produce exceptional output: 115

DB max SPL per pair Balanced XLR, ¼”, and unbalanced RCA inputs allow connection to a range of

Active signal sources Stereo headphone jack allows monitoring using headphones Ergonomic, side-

speakers mounted volume control - simultaneously controls left and right speakers High frequency adjust

control - allows the user to contour HF response to application requirements

Magnetically-shielded transducers for use near CRT monitors and magnetically sensitive

equipment Internal peak limiter and overload protection circuit - protects the system from

damage caused by continuous over-driving

Wall-mount capable using optional MTC-2P mounting kit

Included snap-on pedestals optimize listening angle

for desktop applications including cabling etc as per instruction of Engineer In charge

19 Meeting Room 06 PAX x 2 Nos

65" smart 4K LED Display,Native Resolution 3840 x 2160, Brightness Minimum 390cd/m2, Inputs

HDMI-3,USB(3.0)-3,USB-(2,0)-2,OPS Slot-1,RGB-1, LAN-1,SPDIF-1 or Higher, Output Audio-1(

Audio out to connect additional Speakers if required) , Built in Touch type IR spread /P

Cap/Incell/Inglass, Touch Accuracy ±1.5mm or less, Operating System Support Windows

7/8/10/Windows XP/Linux/Mac/Android (Windows XP/Linux/Mac Support one point touch) , Multi

touch point Min 20 Points or Higher, White Board ,Writing, Pen, Palm Eraser ,Save, Screen

Capture, Storage, Tool Bar, Air Class etc , Android 9.0 or better , Internal Memory (32GB),(Hisi 2,41,356.50 12.00 28,96,278.00

811, Dual core A73+Dual core A53), DDR(4GB), Wi-Fi, Power Indicator, or higher, Screen

Share/Mira cast to Connect TAB/Mobile, Web Browser , 100-240V~, 50/60Hz, 20W(10W x 2) or

higher , ISO9001, ISO14001,ISO45001,

Portable USB Video Confrencing camera,PTZ Camera, 20X Optical Zoom, Digital Zoom: Up to 12X

USB Wide Viewing Angle up to 72.5 Degrees, RJ-45 Port, Quiet Motor with Servo Algorithm for PTZ

Camera Control, Full HD 1080p signal output format with a high frame rate of 60 fps, HDMI, and USB 3.0

synchronous video outputs

Digitally signed by AMIT

Executed No. of

USB: 2.0 (micro-B to Type A) ▪ Bluetooth 5.0, Class 1 (HFP/HSP/A2DP) ▪ NFC for easy pairin, Audio

Specifications ▪ OmniSound ® HD voice ▪ Speaker:

╶ Frequency response: 100Hz to 20,000Hz ╶ Volume: 90dB (SPL 0.5m) ▪ Microphones: ╶ 4 MEMS

microphones: 100Hz to 7,000Hz ╶ Pickup range: 20ft/6m

▪ Audio expansion: daisy chain connection (future release). ▪ Full Duplex▪ Acoustic Echo

Wireless Cancellation and Noise Suppression, Touch buttons: ╶ Answer call / Power

▪ LED Status Indicators ╶ Power status╶ Call status

╶ Bluetooth status ╶ Battery status ▪ Upgradable Software ▪ Upgradable Software, Integrated

Lithium Polymer Battery ╶ Call time up to 14 hour, Temperature range: 5°- 40°C ▪ Relative

humidity: 20 – 80% condensation-free

Active speaker pair of 35 watt, Transducers: LF: 135 mm (5.25 in) low frequency loudspeaker HF:

19 mm (.75 in) Polycarbonate dome tweeter Frequency Range: 80 Hz - 20 kHz Amplifier Power: 35

Watts per channel Maximum SPL Per Pair: 115 dB Crossover Frequency: 4.2 kHz Input Sensitivity:

+4 dBu XLR 1/4"; 0 dBu RCA Signal Input Connectors (x2): Balanced Neutrik* Combo XLR 1/4" TRS;

Unbalanced RCA Power Requirements: 19 VDC / 3.42 A - use only supplied power supply

Headphone Jack: 3.5 mm (1/8") Dimensions: 235 x 159 x 143 mm (9.3 x 6.3 x 5.6 in). tudio quality

transducers for accuracy, and rich bass response: 80 Hz - 20 Khz 35 watt per-channel power

amplifier and high sensitivity drivers produce exceptional output: 115 DB max SPL per pair

Balanced XLR, ¼”, and unbalanced RCA inputs allow connection to a range of signal sources Stereo

23 headphone jack allows monitoring using headphones Ergonomic, side-mounted volume control - Pair 2

simultaneously controls left and right speakers High frequency adjust control - allows the user to

contour HF response to application requirements Magnetically-shielded transducers for use near

CRT monitors and magnetically sensitive equipment Internal peak limiter and overload protection

circuit - protects the system from damage caused by continuous over-driving Wall-mount capable

using optional MTC-2P mounting kit Included snap-on pedestals optimize listening angle for

desktop applications including cabling etc as per instruction of Engineer In charge

Conference Room 9 Pax

75" smart 4K LED Display,Native Resolution 3840 x 2160 (UHD), Brightness Minimum 390cd/m2,

Inputs HDMI-3,USB(3.0)-3,USB-(2,0)-2,OPS Slot-1,RGB-1, LAN-1,SPDIF-1 or Higher, Output

Audio-1( Audio out to connect additional Speakers if required) , Built in Touch type IR spread /P

Cap/Incell/Inglass, Touch Accuracy ±1.5mm or less, Operating System Support Windows

7/8/10/Windows XP/Linux/Mac/Android (Windows XP/Linux/Mac Support one point touch) , Multi

touch point Min 20 Points or Higher, White Board ,Writing, Pen, Palm Eraser ,Save, Screen

Capture, Storage, Tool Bar, Air Class etc , Android 9.0 or better , Internal Memory (32GB),(Hisi

811, Dual core A73+Dual core A53), DDR(4GB), Wi-Fi, Power Indicator, or higher, Screen

Share/Mira cast to Connect TAB/Mobile, Web Browser , 100-240V~, 50/60Hz, 20W(10W x 2) or

higher , ISO9001, ISO14001,ISO45001,

Digitally signed by AMIT

Executed No. of

Portable USB Video Confrencing camera,PTZ Camera, 20X Optical Zoom, Digital Zoom: Up to 12X

USB Wide Viewing Angle up to 72.5 Degrees, RJ-45 Port, Quiet Motor with Servo Algorithm for PTZ

Camera Control, Full HD 1080p signal output format with a high frame rate of 60 fps, HDMI, and USB 3.0

synchronous video outputs

USB: 2.0 (micro-B to Type A) ▪ Bluetooth 5.0, Class 1 (HFP/HSP/A2DP) ▪ NFC for easy pairin, Audio

Specifications ▪ OmniSound ® HD voice ▪ Speaker: ╶ Frequency response: 100Hz to 20,000Hz ╶

Volume: 90dB (SPL 0.5m) ▪ Microphones: ╶ 4 MEMS microphones: 100Hz to 7,000Hz ╶ Pickup

range: 20ft/6m ▪ Audio expansion: daisy chain connection (future release). ▪ Full Duplex▪ Acoustic

Wireless Echo Cancellation and Noise Suppression, Touch buttons: ╶ Answer call / Power╶ End Call ╶

Mic Bluetooth ╶ Volume Up / Down ╶ Mute ▪ LED Status Indicators ╶ Power status╶ Call status ╶

Bluetooth status ╶ Battery status ▪ Upgradable Software ▪ Upgradable Software, Integrated

Lithium Polymer Battery ╶ Call time up to 14 hour, Temperature range: 5°- 40°C ▪ Relative

humidity: 20 – 80% condensation-free

Active speaker pair of 35 watt, Transducers: LF: 135 mm (5.25 in) low frequency loudspeaker HF:

19 mm (.75 in) Polycarbonate dome tweeter Frequency Range: 80 Hz - 20 kHz Amplifier Power: 35

Watts per channel Maximum SPL Per Pair: 115 dB Crossover Frequency: 4.2 kHz

Input Sensitivity: +4 dBu XLR 1/4"; 0 dBu RCA

Signal Input Connectors (x2): Balanced Neutrik* Combo XLR 1/4" TRS; Unbalanced RCA Power

Requirements: 19 VDC / 3.42 A - use only supplied power supply

Headphone Jack: 3.5 mm (1/8") Dimensions: 235 x 159 x 143 mm (9.3 x 6.3 x 5.6 in). tudio quality

transducers for accuracy, and rich bass response: 80 Hz - 20 Khz

35 watt per-channel power amplifier and high sensitivity drivers produce exceptional output: 115

DB max SPL per pair Balanced XLR, ¼”, and unbalanced RCA inputs allow connection to a range of

27 signal sources Stereo headphone jack allows monitoring using headphones Ergonomic, side- Pair 1

mounted volume control - simultaneously controls left and right speakers High frequency adjust

control - allows the user to contour HF response to application requirements

Magnetically-shielded transducers for use near CRT monitors and magnetically sensitive

equipment Internal peak limiter and overload protection circuit - protects the system from

damage caused by continuous over-driving

Wall-mount capable using optional MTC-2P mounting kit

Included snap-on pedestals optimize listening angle

for desktop applications including cabling etc as per instruction of Engineer In charge

Digitally signed by AMIT

Executed No. of

55" smart 4K LED Display,Native Resolution 3840 x 2160, Brightness Minimum 390cd/m2, Inputs

HDMI-3,USB(3.0)-3,USB-(2,0)-2,OPS Slot-1,RGB-1, LAN-1,SPDIF-1 or Higher, Output Audio-1(

Audio out to connect additional Speakers if required) , Built in Touch type IR spread /P

Cap/Incell/Inglass, Touch Accuracy ±1.5mm or less, Operating System Support Windows

7/8/10/Windows XP/Linux/Mac/Android (Windows XP/Linux/Mac Support one point touch) , Multi

touch point Min 20 Points or Higher, White Board ,Writing, Pen, Palm Eraser ,Save, Screen

Capture, Storage, Tool Bar, Air Class etc , Android 9.0 or better , Internal Memory (32GB),(Hisi

811, Dual core A73+Dual core A53), DDR(4GB), Wi-Fi, Power Indicator, or higher, Screen

Share/Mira cast to Connect TAB/Mobile, Web Browser , 100-240V~, 50/60Hz, 20W(10W x 2) or

higher , ISO9001, ISO14001,ISO45001,

55" smart 4K LED Display,Native Resolution 3840 x 2160, Brightness Minimum 390cd/m2, Inputs

HDMI-3,USB(3.0)-3,USB-(2,0)-2,OPS Slot-1,RGB-1, LAN-1,SPDIF-1 or Higher, Output Audio-1(

Audio out to connect additional Speakers if required) , Built in Touch type IR spread /P

Cap/Incell/Inglass, Touch Accuracy ±1.5mm or less, Operating System Support Windows

7/8/10/Windows XP/Linux/Mac/Android (Windows XP/Linux/Mac Support one point touch) , Multi

touch point Min 20 Points or Higher, White Board ,Writing, Pen, Palm Eraser ,Save, Screen

Capture, Storage, Tool Bar, Air Class etc , Android 9.0 or better , Internal Memory (32GB),(Hisi

811, Dual core A73+Dual core A53), DDR(4GB), Wi-Fi, Power Indicator, or higher, Screen

Share/Mira cast to Connect TAB/Mobile, Web Browser , 100-240V~, 50/60Hz, 20W(10W x 2) or

higher , ISO9001, ISO14001,ISO45001

Portable USB Video Confrencing camera,PTZ Camera, 20X Optical Zoom, Digital Zoom: Up to 12X

Wide Viewing Angle up to 72.5 Degrees, RJ-45 Port, Quiet Motor with Servo Algorithm for PTZ

30 Control, Full HD 1080p signal output format with a high frame rate of 60 fps, HDMI, and USB 3.0 Nos. 4

synchronous video outputs

USB: 2.0 (micro-B to Type A) ▪ Bluetooth 5.0, Class 1 (HFP/HSP/A2DP) ▪ NFC for easy pairin, Audio

Specifications ▪ OmniSound ® HD voice ▪ Speaker:

╶ Frequency response: 100Hz to 20,000Hz ╶ Volume: 90dB (SPL 0.5m) ▪ Microphones: ╶ 4 MEMS

microphones: 100Hz to 7,000Hz ╶ Pickup range: 20ft/6m

▪ Audio expansion: daisy chain connection (future release). ▪ Full Duplex▪ Acoustic Echo

Wireless Cancellation and Noise Suppression, Touch buttons: ╶ Answer call / Power

▪ LED Status Indicators ╶ Power status╶ Call status

╶ Bluetooth status ╶ Battery status ▪ Upgradable Software ▪ Upgradable Software, Integrated

Lithium Polymer Battery ╶ Call time up to 14 hour, Temperature range: 5°- 40°C ▪ Relative

humidity: 20 – 80% condensation-free

Digitally signed by AMIT

Executed No. of

Active speaker pair of 35 watt, Transducers: LF: 135 mm (5.25 in) low frequency loudspeaker HF:

19 mm (.75 in) Polycarbonate dome tweeter Frequency Range: 80 Hz - 20 kHz Amplifier Power: 35

Watts per channel Maximum SPL Per Pair: 115 dB Crossover Frequency: 4.2 kHz

Input Sensitivity: +4 dBu XLR 1/4"; 0 dBu RCA

Signal Input Connectors (x2): Balanced Neutrik* Combo XLR 1/4" TRS; Unbalanced RCA Power

Requirements: 19 VDC / 3.42 A - use only supplied power supply

Headphone Jack: 3.5 mm (1/8") Dimensions: 235 x 159 x 143 mm (9.3 x 6.3 x 5.6 in). tudio quality

transducers for accuracy, and rich bass response: 80 Hz - 20 Khz

35 watt per-channel power amplifier and high sensitivity drivers produce exceptional output: 115

DB max SPL per pair Balanced XLR, ¼”, and unbalanced RCA inputs allow connection to a range of

32 signal sources Stereo headphone jack allows monitoring using headphones Ergonomic, side- Pair 4

mounted volume control - simultaneously controls left and right speakers High frequency adjust

control - allows the user to contour HF response to application requirements

Magnetically-shielded transducers for use near CRT monitors and magnetically sensitive

equipment Internal peak limiter and overload protection circuit - protects the system from

damage caused by continuous over-driving

Wall-mount capable using optional MTC-2P mounting kit

Included snap-on pedestals optimize listening angle

for desktop applications including cabling etc as per instruction of Engineer In charge

55" smart 4K LED Display,Native Resolution 3840 x 2160, Brightness Minimum 390cd/m2, Inputs

HDMI-3,USB(3.0)-3,USB-(2,0)-2,OPS Slot-1,RGB-1, LAN-1,SPDIF-1 or Higher, Output Audio-1(

Audio out to connect additional Speakers if required) , Built in Touch type IR spread /P

Cap/Incell/Inglass, Touch Accuracy ±1.5mm or less, Operating System Support Windows

7/8/10/Windows XP/Linux/Mac/Android (Windows XP/Linux/Mac Support one point touch) , Multi

touch point Min 20 Points or Higher, White Board ,Writing, Pen, Palm Eraser ,Save, Screen

Capture, Storage, Tool Bar, Air Class etc , Android 9.0 or better , Internal Memory (32GB),(Hisi

811, Dual core A73+Dual core A53), DDR(4GB), Wi-Fi, Power Indicator, or higher, Screen

Share/Mira cast to Connect TAB/Mobile, Web Browser , 100-240V~, 50/60Hz, 20W(10W x 2) or

higher , ISO9001, ISO14001,ISO45001,

VC for ED Room cabins:

34 Portable USB Video Confrencing, PTZ Camera, 12x auto focus zoom lens, 360 continuous Nos 5

rotation, high-speed pan and tilt operations.

Digitally signed by AMIT

Executed No. of

Active Speakers for ED Room:

Active speaker pair of

Frequency Range: 80 Hz - 20 kHz

Amplifier Power: 35 Watts per channel Maximum

SPL Per Pair: 115 dB Crossover Frequency: 4.2 kHz

Open Pluggable Specification(OPS):

Intel Core i5 11th Generation, 8GB RAM, 256GB SSD, 1000 mbps gigaLAN, 450 mbps WI-FI,

bluetooth Windows 10 Pro License Pre-Loaded, HDMI 2.0, Mini DP, USB 2.0 x 2 USB 3.0 x 2,

USB C TYPE X1, Audio In, Audio Out

E CAMC of Gass Supression, FF & PA Works:

Gas Suppression System

having following Equipments:

Seamless Novec 1230 Cylinder and Valve Assembly, 34

Ltrs. Capacity - 2 Nos.

FM 200 - 60 Kgs

Electrical Actuator for Master Cylinder - 2 Nos.

Discharge Hose - 2 Nos.

Cylinder Low Pressure Switch - 2 Nos.

Nozzles, 360 Deg / 180 Deg Throw - 4 Nos.

Suppression System Piping - 1 Lot

Gas Release Switch/Module - 2 Nos.

Abort Switch - 2 Nos.

Gas Release Panel - 2 Nos.

Make: Ravel/ADN (Including Refilling of Gas per the requirement of complete operation of system)

Fire Fighting System

CAMC of Fire Fighting System having Following Equipments:

Hydrants - 1 Lot

Sprinklers - 1 Lot

Fire Piping and Accessories - 1 Lot

b) Mechanical Foam gas cartridge type. 9 Kg capacity (IS:15683).

c) ABC dry powder stored pressure type 6 kg capacity (IS:15683).

(Including Refilling of cylinders as per the requirement of complete operation of system)

Fire Alarm and PA System

Digitally signed by AMIT

Executed No. of

CAMC of Fire Alarm and PA System having Following Equipments:

Intelligent analog addressable photothermal detector - 150 Nos.

Response Indicator - 19 Nos.

Addressable fire control module - 4 Nos.

Addressable horn cum strobe - 4 Nos.

Addressable manual call point - 4 Nos.

1.5/3/6W ceiling speaker - 86 Nos.

Digital audio amplifier 75 Watt - 3 Nos.

Voice command keypad 6 zone - 1 No.

Loop Card capacity of 159 detectors For BMS Fire integration - 1 No.

Interface Card for BMS fire integration - 1 No.

Repeater panel - 1 No.

F CAMC of Smart Rack:

1 i-CSR Two smart Racks Solution with 10kW Cooling & 10kW UPS (N+N) Set 1

Server / Network Rack - 800W x 2000H (42U) x 1200D, 100H Base Plinth with A.V pad, Front Glass

Door, Rear Split Plain Door, High Density Vertical Cable Manager & Accessories. 2 nos;

1U Horizontal Cable Manager with PVC channel type 4

Copper Earth Rail 15x5 with screws and insulators 2

Vertical PDU - BASIC & UPS DBBasic Vertical PDU, 30A, 1Ф, 250 VAC, Vertical Rack PDU with “C”

curve 32A single pole MCB with safety guard, power indicator, 16nos of IEC-320-C13 Sockets, 6nos

of IEC-320-C19 Sockets, 2nos of EMO-71-1 6/13Amp Universal Sockets, 6 sq.mm 3 core 4.5 meter 4

cable with NEMA Twist Lock Plug (30A ENP-LD6-30) & Mounting brackets hardware for vertical

UPS DB, 1Phase 32A PDU, with NEMA socket 1 no. & C13 socket 2 nos.,with 32A MCB & PG-16

cable gland,Colour:RAL 9005

In-Rack Cooling System - 10kW (N+N)-

Cooling Unit Module (DX Type, Digital Scroll) - 10kW with Redundancy (N+N)

- Indoor Unit Module with EC Fans

Low Side Works for Air-Condition System (15 mtrs dist b/n indoor & outdoor for each 10kW

Environmental Monitoring System with water leaks detection system, temperature & humidity

sensor, Somke Sensor, door sensor & alarm beacon

Biometric Access Control System for Front Rack Door with EM Locks, cabling, bkts etc. 2

Standalone Ultrasonic Rodent Repeller 2

Automatic Door Opening system (For Front Doors) 2

Digitally signed by AMIT

Executed No. of

Rack Based Fire Detection & Extinguishing System with FITECH 1230 / FK-5-1-12 Suppression

(2 Rack System)

Electrical Distribution Boards & Cabling Works

Raw Power DB : 19" Rack Mountable Raw Power Distribution Panel with TVSS, Incomer breaker,

Outgoing breakers for Cooling Units, UPS Units, Rodent Repellant, etc.

Cable Trough of size : 300W x 50H mm with Cover Lid & necessary accessories for fixing. 20 mtr

UPS with Battery Bank & STS

10 KVA /10 KW Rack Mount UPS with 1 Phase Input and 1 Phase Output Online UPS ( Model :

External Battery Rack with 15min back-up on full load with all accessories & cables. 2

16A Rack Mountable (1U) STS 16 (Source Transfer Switch) 1

as approved by EIC. Make- Rittal

2 STATIC SWITCH MODULE

Static switch module with microprocessor based control and suitable for linear and non linear load

at particulars distribution board of critical load in event of short circuit overload or any other fatal

condition with built-in Technical Protections like short circuit, Overload, High/Low Voltage cutoff

protection of load from source inclusive of Bypass facility Static Bypass Module is activated during

malfunctioning conditions of load like :-

• Short Circuit

• Bypassing of particular load if required

• Resulting in non tripping of main UPS unit • Input Voltage (320-460VAC) 3 phase

• Input frequency 50Hz Indication & Monitoring

• UPS Supply on/source I

• Load on UPS supply/source I

• Main supply on/source II

• Load on mains supply/Bypass

• Bypass Switch on

• Bypass Switch off

complete as required and as per specifications.

Capacity: 63A 3 Phase

G CAMC of CCTV:

Digitally signed by AMIT

Executed No. of

5MP IR IP H.265 Vandal Proof Dome camera with 2.8 to 12mm Motorized Lens,Smart IR, up to 30M IR

distance,Up to 120 dB WDR (Wide Dynamic Range),3D DNR (Digital Noise Reduction),H.265+, H.265, H.264,

MJPEG,Corridor mode, Triple streams,3-Axis, IP67, IK10 Vandal Resistant,Colour: 0.005Lux (F1.4, AGC ON), 0

Lux with IR,Video Compression H.265+, H.265, H.264, MJPEG,Behavior Detection Intrusion, Crossing line,

1 Motion detection, Object left, Missing object,Intelligent Identification Face detection, Defocus, Scene Nos 19.00

Change,PoE (IEEE802.3 af) Power consumption: Max 7.2W,Edge Storage Micro SD Card, Up to 256GB, ANR

Support,Working Environment -40°C ~ +60°C, Humidity ≤ 90% RH(Non-condensing),Compatible Integration

ONVIF (Profile S/G), API.

16Ch Embedded Network Video Recorder with 4 Sata Supports 1 × RJ45 1000M ,4K Cameras, HDMI, VGA,

RAID, Redundant power supply, Smart Analytics and ONVIF

SSD Hard Disk Drive 8TB, 24/7 surveillance category Only complete etc as required.etc.all complete.

55" Flat Screen HD led (24X7) with Interfaces include HDMI, DVI, D-sub, Component and Composite input as

4 well as RS-232C and RJ45 for extensive connectivity, remote control and wall mount unit / floor stand Nos 1.00

complete with making connections etc complete as reqd.

4Ch Embedded Network Video Recorder with 2 Sata Supports 1 × RJ45 1000M ,4K Cameras, HDMI, VGA,

RAID, Redundant power supply, Smart Analytics,

32" Flat Screen HD led (24X7) with Interfaces include HDMI, DVI, D-sub, Component and Composite input as

6 well as RS-232C and RJ45 for extensive connectivity, remote control and wall mount unit / floor stand Nos 1.00

complete with making connections etc complete as reqd.

H CAMC of EPABX

Server based Communication System with all the required Software licenses and

Hardware - IP-PBX/IP Telephony Communications Server: The IP Telephony Solution shall

support the following Services - Voice, Video, IM, Presence and Audio Conference The

Solution should be built on Active-Active Redundant Servers The IP Telephony Solution

should support H.323 and SIP The Solution should support the following Trunks - FXO, E1

PRI and SIP The IP Telephony solution should incorporate all licenses for the Phones and

1 Trunks Solution should support 80 Extensions from Day 1 with future scalabilityupto 5000 Nos 1

users. Licenses for all Phones supplied should be provisioned on Day1 Solution should

support Hard IP Phones, Softphones, Video Phones, 50 Analog Extensions with necessary

Licenses, Rack mount architecture, complete as required and as per technical

specifications.

Digitally signed by AMIT

Executed No. of

Executive Level IP Phone with Color display – 3.7 inches x 2.1 inches (9.5 cm x 5.4 cm)-

Diagonal width: 4.3 inches (11 cm), Touch Screen display, 4-position adjustable tilt

display, Permanently-labeled feature buttons:, speaker, mute, headset, contacts, home,

history, message, phone, forwarding, volume (separate volume levels in handset, speaker,

ringer, and headset), Red LEDs on speaker, mute, headset, message and history, 24

administrative buttons, Wideband speakerphone 0-5 Softkeys, Ergonomic hearing aid

compatible, handset supporting TTD acoustic coupler, Bluetooth and DECT headset

2 support with adapter, Message waiting indicator, Ethernet (10/100/1000) line interface, Nos 32

Secondary Ethernet (10/100/1000)line interface, Optional IEEE PoE 802.3af adapter

registers as class 2 device, SIP protocol, H.323 protocol support, Standards-based codec

Brazilian Portuguese, Simplified, Chinese, Dutch, English, Canadian,French, Parisian

French, German,Hebrew, Italian, Japanese (Kanji,Hiragana and Katakana), Korean, Latin

American Spanish, Castilian Spanish, and Russian. Includ Licence.

2.8” (diagonal) color display—320 x 240 pixels, Multiple line phone with four red / green

line / feature indicators around display, 4 Context sensitive soft keys, Hard buttons for

phone, messages, contacts, history, home, navigation cluster, headset, speaker, volume,

mute, LEDs for speaker, mute, headset, essage, history, Wideband audio in handset and

wired headset, Full duplex speakerphone & handset, Ergonomic hearing aid compatible

handset supports TTD acoustic coupler, Message waiting indicator, Mute key with optional

mute alerting, IC call alerting with 360-degree visibility, Dual-position stand, optional wall-

mount stand, Gigabit Ethernet (10 / 100 / 1000) line interface, Second Ethernet interface

3 10 / 100 / 1000 Mbps, PoE Class (IEEE 802.3af) registers as class 1 device and supports Nos 53

802.3az, Optional AC to 5 volt power supply • SIP protocol support, Standards-based codec

support: G.722, Opus, Configurable via Web interface, Support for HTTPS, TLS and SRTP for

encryption, Recent Call Log (100 entries), Zero touch deployment via Device Enrollment

Services Support, Supports the following languages: Dutch, English (UK & US), French,

(Canada), French (France), German, Italian, Japanese, Portuguese (Brazil), Simplified

Chinese, Spanish (Latin America), Spanish (Spain),Traditional Chinese, Includ Licence.

Additional Items:

CAMC of Biometric Attendance system with software:

Supported by rugged fingerprint sensors, This time attendance machine qualifies IP65

2 standards, Report generation on employee attendance, Centralized Data Collection, Nos 1

Personnel-wise attendance tracking and monitoring.

Power Charger (7.2 Kw x 1 No)

Digitally signed by AMIT

Executed No. of

Ziptron (3 Nos)

Wall Mounting Unit 7.2 KW

Digitally signed by AMIT

CAMC/AMC ESTIMATE FOR HVAC/VRV, FIRE ALARM & PA, CCTV, EPABX, ELECTRICAL, IT, AV etc. ITEMS FOR IREDA OFFICE, IBC, EKN, 7th FLOOR, TOWER-2

Executed Rate Per No. of

Qty Month Months

A CAMC of HVAC/VRV:

Modular type Variable Refrigerant Flow/Variable Refrigerant Volume air cooled Outdoor units suitable for

cooling and heating, having all hermetically sealed inverter type Scroll Compressor(s), minimum two

compressors for above 14 HP modules, microprocessor based Controller, top discharge type condensing

unit(s), with R 410 A Refrigerant, vibration isolators, with suitable foundation etc. complete as required. The

1 unit shall deliver the rated capacity at AHRI Conditions and work even at 50°C ambient temperature without per HP 40.00

tripping. The unit shall be suitable to work on 400V +/- 10%, 3 Phase, 50Hz AC power supply. The unit shall

be filled with first charge of the refrigerant and ready for use as required. The COP at AHRI conditions shall

not be less than 3.1 and IEER not less than 6.5 .

4-way flow VRV/VRF Cassette Type Indoor ceiling mounted unit equipped with synthetic washable media pre-

filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX

Copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration

isolation, cord less remote control etc., suitable for operation on single phase 230 V ± 10%, 50Hz AC supply,

2 complete, as required. The unit shall have automatic force shut down provision in case of fire on receiving

signal from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB

and 19 Degree C

WB temperature.

Inverter type High Wall Indoor Unit with Stablizer, 3 star, including cost of copper piping (upyo 15

mtr, drain pipe wire and remote)

3 High Wall - 2 Tr (Inverter Compressor with stablizer) Nos 2

VAV BOX (WITH INTEGRAL SOUND ATTENUATOR)

Pressure independent rectangular VAV unit with integral sound attenuator made of 22G GI sheet

casing length 900mm consisting of 25mm thick 48kg/m3 density fiber glass wool covered with

4 tissue paper ,elliptical volume control damper , calibrated differential pressure sensor (DPT

sensors) at inlet complete with digital Thermostat.( All VAV shall be factory calibrated ).

Digitally signed by AMIT

Executed Rate Per No. of

Qty Month Months

Variable Frequency Drive (VFD)

380-400 VAC, IP-54 Chassis, RFI class A1 (C2), No brake chopper.

B CAMC of Electrical:

The following sheet steel cubicle type panels fabricated from 1.6mm thick CRCA sheet, dust and vermin

proof, indoor type TPN Panels with hinged lockable doors fabricated from 2mm thick CRCA sheet, suitable

for 415V, 3 phase 4 wire 50Hz AC supply with rear access for cable alley and with segregated bus-bar

1 chamber with tinned aluminium bus bar and including supplying and fixing following switchgears, meters Each 1 3,316.61 12.00 39,799.32

and accessories, inter-connections, bonding to earth, powder coated painting and marking as specified.

Switch boards complete as per schematic diagram:

Type of construction: Form 3

IP classification: 42

The LT PANEL shall be electrically inter-locked as shown in Schematic diagram and as detailed in the

Colour: Gray Powder Coated, as per approved sample.

1 nos, 250 Amps. 4 pole MCCB , i.e four pole Moulded Case Circuit Breaker of fault breaking capacity 25 KA

(ICS=ICU up to 433 V) complete in all respect

TPN aluminum bus bars of minimum of 320 Amps capacity with heat shrinkable colored sleeves and I/C

DMC/SMC bus bars supports at required intervals complete for cross section, size supports & their spacing

etc. for withstanding fault level of 25 MVA for 1 Sec.

(a) 63 Amps, TPN, MCB -6 Nos.

(b) 40 Amps, TPN, MCB - 6 nos

(c ) 125 Amps TPN MCB - 4 nos

Panel complete as above

The following sheet steel cubicle type panels fabricated from 1.6mm thick CRCA sheet, dust and vermin

proof, indoor type TPN Panels with hinged lockable doors fabricated from 2mm thick CRCA sheet, suitable

for 415V, 3 phase 4 wire 50Hz AC supply with rear access for cable alley and with segregated bus-bar

2 chamber with tinned aluminium bus bar and including supplying and fixing following switchgears, meters Each 1 2,819.30 12.00 33,831.60

and accessories, inter-connections, bonding to earth, powder coated painting and marking as specified.

Switch boards complete as per schematic diagram:

Digitally signed by AMIT

Executed Rate Per No. of

Qty Month Months

Type of construction: Form 3

IP classification: 42

The LT PANEL shall be electrically inter-locked as shown in Schematic diagram and as detailed in the

Colour: Gray Powder Coated, as per approved sample.

Two (2) nos, 125 Amps. 4 pole MCCB , i.e four pole Moulded Case Circuit Breaker of fault breaking capacity

25 KA (ICS=ICU up to 433 V) complete in all respect

TPN aluminum bus bars of minimum of 400 Amps capacity with heat shrinkable colored sleeves and I/C

DMC/SMC bus bars supports at required intervals complete for cross section, size supports & their spacing

etc. for withstanding fault level of 25 MVA for 1 Sec.

1 Nos. 250A, 4P, MCCB (25kA) with phase indicating lamp protected with 2A, SP, MCB's along with E/M

(a) 63 Amps, TPN, MCB - 2 nos

(b ) 40 Amps, TPN MCB - 6 nos

Panel complete as above

High Efficient 60kVA/60 KW Model IGBT Rectifier & IGBT Inverter, Modular Fault Tolerant designFailure in

any one of the module the others keeps supplying to the load without interruption. Approved Make, 12V

VRLA Batteries, 65 AH or saiuitable for 30 minutes backup. Exide (40 nos on each bank) Make Exide,

3 Accessories ( Cabling between UPS and the Battery upto 10 Mtr distance for each UPS considering cable NO. 2 50,064.96 12.00 6,00,779.52

Routing,Battery Rack and Battery Interlinks, lugs etc ) DC MCCB between UPS and Battery complete in all

respect as per the directions of engineer in charge. UPS shall produce 30 minutes backup.

C CAMC of IT Active Works:

24-Port Layer 3 Stackable Managed Gigabit Switch, 20 x 10/100/1000BASE-T ports With 4 x Combo

10/100/1000BASE-T/SFP ports, 4 x 10G SFP+ ports, Switch Resource Management (SRM) for flexible

1 management of system resources, Redundant Power Supply (RPS) support, MPLS L2VPM/L3 VPN support, Nos. 1.00

Full L3 routing protocol support including OSPF, BGP, and ISIS for IPv4/IPv6. As Approved by NSL Incharge.

Access Switch of 48 x 1G POE+, 4 x SFP+ , 370W PoE, Switching Capacity of switch is of 176 Gbps having

Forwarding performance (64-byte packet size): 130 Mpps, Secure Shell (SSH), RADIUS, TACACS + DRAM 2GB

2 , Flash 2GB , 10K IPv4 Routes ,1K multicast Routes ,16K MAC address , 16K flow entries L3 Protcols like OSPF , Nos. 6.00

PBR, MACsec, PIM , QOS from day-1 , As Approved by NSL Incharge.

Digitally signed by AMIT

Executed Rate Per No. of

Qty Month Months

48 port 10/100/1000 Base T Switch with 4 x 10G SFP+ ports,The Switch should have 16K MAC address,

Should have RJ-45 console port should support MSTP and DUAL configuration, Should support Static 91,358.63 12.00 10,96,303.56

Route Entry: IPv4 124; IPv6 50 , Should support IP-MAC- Port Binding strictly management network devices

3 preventing illegal access and the Man-in- the-middle attack, Should support Asymmetric VLAN, Auto Voice Nos. 6.00

VLAN, Should support Cable diagnostics, Time-based PoE: PoE ports can be turned on/off by port or

system through schedule, Operating Temperature -5 to 50°C (23 to 122°F). As Approved by NSL Incharge.

Wi-Fi standard, IEEE’s new 802.11ac Wave 2 specification, and meets the growing requirements of wireless

networks by delivering a better user experience. The 1830 Series extends support to a new generation of Wi-

4 Fi clients, such as smartphones, tablets, and high-performance laptops that have integrated 802.11ac Wave Nos. 30.00

1 or Wave 2 support.

Modules 10G - 30 Nos. & LC- LC multimode OFC type patch cord - 10 Nos.

C.1 AMC of Passive Works:

Annual Maintenance Contract of Passive Components System having Following Equipments:

UTP Components for Data - 1 Lot

200 Pair MDF Box -1 Lot

UTP Components for Wifi - 1 Lot

UTP Components for CCTV and Access Control - 1 Lot

D CAMC of AV Works:

98" smart 4K LED Display,Native Resolution 3840 x 2160 (UHD), Brightness Minimum 490cd/m2,

Inputs HDMI-3,USB(3.0)-3,USB-(2,0)-2,OPS Slot-1,RGB-1, LAN-1,SPDIF-1 or Higher, Output

Audio-1( Audio out to connect additional Speakers if required) , Built in Touch type IR spread /P

Cap/Incell/Inglass, Touch Accuracy ±1.5mm or less, Operating System Support Windows

98" main 7/8/10/Windows XP/Linux/Mac/Android (Windows XP/Linux/Mac Support one point touch) , Multi

LED touch point Min 20 Points or Higher, White Board ,Writing, Pen, Palm Eraser ,Save, Screen

display Capture, Storage, Tool Bar, Air Class etc , Android 9.0 or better , Internal Memory (32GB),(Hisi 811,

(1-CMD Dual core A73+Dual core A53), DDR(4GB), Wi-Fi, Power Indicator, or higher, Screen Share/Mira

1-Board cast to Connect TAB/Mobile, Web Browser , 100-240V~, 50/60Hz, 32W(16W x 2) or higher ,

Room) ISO9001, ISO14001,ISO45001,

The display should be a smart screen and touch enabled alongwith stylus/pen. The display should

also have provision for OPS PC.

Digitally signed by AMIT

Executed Rate Per No. of

Qty Month Months

55" smart 4K LED Display,Native Resolution 3840 x 2160, Brightness Minimum 390cd/m2, Inputs

HDMI-3,USB(3.0)-3,USB-(2,0)-2,OPS Slot-1,RGB-1, LAN-1,SPDIF-1 or Higher, Output Audio-1(

Audio out to connect additional Speakers if required) , Built in Touch type IR spread /P

Cap/Incell/Inglass, Touch Accuracy ±1.5mm or less, Operating System Support Windows

7/8/10/Windows XP/Linux/Mac/Android (Windows XP/Linux/Mac Support one point touch) , Multi

touch point Min 20 Points or Higher, White Board ,Writing, Pen, Palm Eraser ,Save, Screen

55" main Capture, Storage, Tool Bar, Air Class etc , Android 9.0 or better , Internal Memory (32GB),(Hisi 811,

2 LED Dual core A73+Dual core A53), DDR(4GB), Wi-Fi, Power Indicator, or higher, Screen Share/Mira Nos. 4

display cast to Connect TAB/Mobile, Web Browser , 100-240V~, 50/60Hz, 20W(10W x 2) or higher ,

ISO9001, ISO14001,ISO45001,

The display should be a smart screen and touch enabled alongwith stylus/pen. The display should

also have provision for OPS PC.

Portable USB Video Confrencing camera,PTZ Camera, 20X Optical Zoom, Digital Zoom: Up to 12X

USB Wide Viewing Angle up to 72.5 Degrees, RJ-45 Port, Quiet Motor with Servo Algorithm for PTZ

Camera Control, Full HD 1080p signal output format with a high frame rate of 60 fps, HDMI, and USB 3.0

synchronous video outputs

Wireless digital boundary layer Microphone with 18 or more channel, RF output 80mW or more,

Cardioid pickup pattern, Frequency range : 1880 to 1930 MHz, Connectivity : RJ-45, 256-bit AES

4 MICS Encryption (specifications includes single microphone set of transmitter and receiver) etc and Nos. 14

complete as required.

wireless digital microphone charger, charging capacity : 2 or more simultaneously with lighting

Charger indication, Qi charging, Should be from same OEM as of wireless mic etc and complet required as

base per specifications.

Digital signal processor with minimum 14no. Or more Mic / line input with phantom power and

AEC and 8 or more line output, at least 2 channel of USB input and output for software Video

Conferencing,, Should have sampline rate of 48kHz or better, Should be expandable for port

expansion. 64x64 or more Dante Input for Digital audio transfer as per need,should support

Control with App via iOS and Android devices, or any third-party control system, Shall have Built-

in filters, feedback suppression, AGC etc complete as required as per specifications

Digitally signed by AMIT

Executed Rate Per No. of

Qty Month Months

6.5" two-way coaxial thin edge ceiling loudspeaker, 100V transformer power taps : 24,12,6, watts,

Conical dispersion : 145° or more, impedance : 8, low impedance RMS continous power : 30watts,

7 frequency range : 50 Hz - 20 kHz or better, frequency response : 60Hz - 20KHz or better etc Nos. 12

complete required as per specifications.

Quad channel Amplifier, 4 X 120watt or more, THD+N (@ 1 kHz) : < 0.3%, Technology : Class-D,

Common mode rejection ratio : 70dB or better, Temperature controlled FAN, Switching mode

power supply, should have Protection features like : DC Short circuit & Over heating & Over load &

Signal limiting etc, Built-in high pass filter and gain adjustment option etc complete required as per

specifications.

This HDMI Switcher/ Splitter 8x4 can connect 2HD signal sources with 8HD display terminals. It can

easily split 2-way HD signal sources to 8 HDTVs or projectors which support HD. It also can amplify

the HDMI signal. The two input HD signal sources can be switched freely. The HDMI Switch/Splitter

2x8 can support highest video resolution 3840x2160/30hz,Compatible with fully HDMI 1.3/1.4

Specification compliant. buffer HDMI signals at the same time, HDMI or DVI to HDMI cables used

9 Switcher for inputs and outputs. Included IR remote adapter for operational flexibility and easy control, no Nos. 1

manual clicking the select button needed. Support single high definition display and multiple

output HD signal sources, such as DVD Players, A/V receiversand Set Top Boxes, 360 Sky Box

Freesat Virgin Bluray Player DVD HDTV Projector Camcorder HTPC Laptop

65" smart 4K LED Display,Native Resolution 3840 x 2160, Brightness Minimum 390cd/m2, Inputs

HDMI-3,USB(3.0)-3,USB-(2,0)-2,OPS Slot-1,RGB-1, LAN-1,SPDIF-1 or Higher, Output Audio-1(

Audio out to connect additional Speakers if required) , Built in Touch type IR spread /P

Cap/Incell/Inglass, Touch Accuracy ±1.5mm or less, Operating System Support Windows

65" main 7/8/10/Windows XP/Linux/Mac/Android (Windows XP/Linux/Mac Support one point touch) , Multi

11 LED touch point Min 20 Points or Higher, White Board ,Writing, Pen, Palm Eraser ,Save, Screen Nos. 1

display Capture, Storage, Tool Bar, Air Class etc , Android 9.0 or better , Internal Memory (32GB),(Hisi 811,

Dual core A73+Dual core A53), DDR(4GB), Wi-Fi, Power Indicator, or higher, Screen Share/Mira

cast to Connect TAB/Mobile, Web Browser , 100-240V~, 50/60Hz, 20W(10W x 2) or higher ,

ISO9001, ISO14001,ISO45001.

Digitally signed by AMIT

Executed Rate Per No. of

Qty Month Months

Portable USB Video Confrencing camera,PTZ Camera, 20X Optical Zoom, Digital Zoom: Up to 12X

Wide Viewing Angle up to 72.5 Degrees, RJ-45 Port, Quiet Motor with Servo Algorithm for PTZ

12 Control, Full HD 1080p signal output format with a high frame rate of 60 fps, HDMI, and USB 3.0 Nos. 2

synchronous video outputs

USB: 2.0 (micro-B to Type A) ▪ Bluetooth 5.0, Class 1 (HFP/HSP/A2DP) ▪ NFC for easy pairin, Audio

Specifications ▪ OmniSound ® HD voice ▪ Speaker:

╶ Frequency response: 100Hz to 20,000Hz ╶ Volume: 90dB (SPL 0.5m) ▪ Microphones: ╶ 4 MEMS

microphones: 100Hz to 7,000Hz ╶ Pickup range: 20ft/6m

▪ Audio expansion: daisy chain connection (future release). ▪ Full Duplex▪ Acoustic Echo

Wireless Cancellation and Noise Suppression, Touch buttons: ╶ Answer call / Power

Mic ╶ End Call ╶ Bluetooth ╶ Volume Up / Down ╶ Mute

▪ LED Status Indicators ╶ Power status╶ Call status

╶ Bluetooth status ╶ Battery status ▪ Upgradable Software ▪ Upgradable Software, Integrated

Lithium Polymer Battery ╶ Call time up to 14 hour, Temperature range: 5°- 40°C ▪ Relative

humidity: 20 – 80% condensation-free

Digitally signed by AMIT

Executed Rate Per No. of

Qty Month Months

Active speaker pair of 35 watt, Transducers: LF: 135 mm (5.25 in) low frequency loudspeaker HF:

19 mm (.75 in) Polycarbonate dome tweeter Frequency Range: 80 Hz - 20 kHz Amplifier Power: 35

Watts per channel Maximum SPL Per Pair: 115 dB Crossover Frequency: 4.2 kHz

Input Sensitivity: +4 dBu XLR 1/4"; 0 dBu RCA

Signal Input Connectors (x2): Balanced Neutrik* Combo XLR 1/4" TRS; Unbalanced RCA Power

Requirements: 19 VDC / 3.42 A - use only supplied power supply

Headphone Jack: 3.5 mm (1/8") Dimensions: 235 x 159 x 143 mm (9.3 x 6.3 x 5.6 in). tudio quality

transducers for accuracy, and rich bass response: 80 Hz - 20 Khz

35 watt per-channel power amplifier and high sensitivity drivers produce exceptional output: 115

DB max SPL per pair Balanced XLR, ¼”, and unbalanced RCA inputs allow connection to a range of

14 signal sources Stereo headphone jack allows monitoring using headphones Ergonomic, side- Pair 2

mounted volume control - simultaneously controls left and right speakers High frequency adjust

control - allows the user to contour HF response to application requirements

Magnetically-shielded transducers for use near CRT monitors and magnetically sensitive

equipment Internal peak limiter and overload protection circuit - protects the system from damage

caused by continuous over-driving

Wall-mount capable using optional MTC-2P mounting kit

Included snap-on pedestals optimize listening angle

for desktop applications including cabling etc as per instruction of Engineer In charge

Meeting Room 07 PAX (2 Nos)

75" smart 4K LED Display,Native Resolution 3840 x 2160 (UHD), Brightness Minimum 390cd/m2,

Inputs HDMI-3,USB(3.0)-3,USB-(2,0)-2,OPS Slot-1,RGB-1, LAN-1,SPDIF-1 or Higher, Output

Audio-1( Audio out to connect additional Speakers if required) , Built in Touch type IR spread /P

Cap/Incell/Inglass, Touch Accuracy ±1.5mm or less, Operating System Support Windows

75" main 7/8/10/Windows XP/Linux/Mac/Android (Windows XP/Linux/Mac Support one point touch) , Multi

15 LED touch point Min 20 Points or Higher, White Board ,Writing, Pen, Palm Eraser ,Save, Screen Nos. 2

display Capture, Storage, Tool Bar, Air Class etc , Android 9.0 or better , Internal Memory (32GB),(Hisi 811,

Dual core A73+Dual core A53), DDR(4GB), Wi-Fi, Power Indicator, or higher, Screen Share/Mira

cast to Connect TAB/Mobile, Web Browser , 100-240V~, 50/60Hz, 20W(10W x 2) or higher ,

ISO9001, ISO14001,ISO45001.

Digitally signed by AMIT

Executed Rate Per No. of

Qty Month Months

Portable USB Video Confrencing camera,PTZ Camera, 20X Optical Zoom, Digital Zoom: Up to 12X

USB Wide Viewing Angle up to 72.5 Degrees, RJ-45 Port, Quiet Motor with Servo Algorithm for PTZ

Camera Control, Full HD 1080p signal output format with a high frame rate of 60 fps, HDMI, and USB 3.0

synchronous video outputs

USB: 2.0 (micro-B to Type A) ▪ Bluetooth 5.0, Class 1 (HFP/HSP/A2DP) ▪ NFC for easy pairin, Audio

Specifications ▪ OmniSound ® HD voice ▪ Speaker:

╶ Frequency response: 100Hz to 20,000Hz ╶ Volume: 90dB (SPL 0.5m) ▪ Microphones: ╶ 4 MEMS

microphones: 100Hz to 7,000Hz ╶ Pickup range: 20ft/6m

▪ Audio expansion: daisy chain connection (future release). ▪ Full Duplex▪ Acoustic Echo

17 Cancellation and Noise Suppression, Touch buttons: ╶ Answer call / Power Nos. 2

╶ End Call ╶ Bluetooth ╶ Volume Up / Down ╶ Mute

▪ LED Status Indicators ╶ Power status╶ Call status

╶ Bluetooth status ╶ Battery status ▪ Upgradable Software ▪ Upgradable Software, Integrated

Lithium Polymer Battery ╶ Call time up to 14 hour, Temperature range: 5°- 40°C ▪ Relative

humidity: 20 – 80% condensation-free

Active speaker pair of 35 watt, Transducers: LF: 135 mm (5.25 in) low frequency loudspeaker HF:

19 mm (.75 in) Polycarbonate dome tweeter Frequency Range: 80 Hz - 20 kHz Amplifier Power: 35

Watts per channel Maximum SPL Per Pair: 115 dB Crossover Frequency: 4.2 kHz

Input Sensitivity: +4 dBu XLR 1/4"; 0 dBu RCA

Signal Input Connectors (x2): Balanced Neutrik* Combo XLR 1/4" TRS; Unbalanced RCA Power

Requirements: 19 VDC / 3.42 A - use only supplied power supply

Headphone Jack: 3.5 mm (1/8") Dimensions: 235 x 159 x 143 mm (9.3 x 6.3 x 5.6 in). tudio quality

transducers for accuracy, and rich bass response: 80 Hz - 20 Khz

35 watt per-channel power amplifier and high sensitivity drivers produce exceptional output: 115

DB max SPL per pair Balanced XLR, ¼”, and unbalanced RCA inputs allow connection to a range of

18 signal sources Stereo headphone jack allows monitoring using headphones Ergonomic, side- Pair 1

mounted volume control - simultaneously controls left and right speakers High frequency adjust

control - allows the user to contour HF response to application requirements

Magnetically-shielded transducers for use near CRT monitors and magnetically sensitive

equipment Internal peak limiter and overload protection circuit - protects the system from damage

caused by continuous over-driving

Wall-mount capable using optional MTC-2P mounting kit

Included snap-on pedestals optimize listening angle

for desktop applications including cabling etc as per instruction of Engineer In charge

Digitally signed by AMIT

Executed Rate Per No. of

Qty Month Months

19 Meeting Room 06 PAX x 2 Nos

65" smart 4K LED Display,Native Resolution 3840 x 2160, Brightness Minimum 390cd/m2, Inputs

HDMI-3,USB(3.0)-3,USB-(2,0)-2,OPS Slot-1,RGB-1, LAN-1,SPDIF-1 or Higher, Output Audio-1(

Audio out to connect additional Speakers if required) , Built in Touch type IR spread /P

Cap/Incell/Inglass, Touch Accuracy ±1.5mm or less, Operating System Support Windows

7/8/10/Windows XP/Linux/Mac/Android (Windows XP/Linux/Mac Support one point touch) , Multi

touch point Min 20 Points or Higher, White Board ,Writing, Pen, Palm Eraser ,Save, Screen

Capture, Storage, Tool Bar, Air Class etc , Android 9.0 or better , Internal Memory (32GB),(Hisi 811,

Dual core A73+Dual core A53), DDR(4GB), Wi-Fi, Power Indicator, or higher, Screen Share/Mira

ISO9001, ISO14001,ISO45001,

Portable USB Video Confrencing camera,PTZ Camera, 20X Optical Zoom, Digital Zoom: Up to 12X

USB Wide Viewing Angle up to 72.5 Degrees, RJ-45 Port, Quiet Motor with Servo Algorithm for PTZ

Camera Control, Full HD 1080p signal output format with a high frame rate of 60 fps, HDMI, and USB 3.0

synchronous video outputs

USB: 2.0 (micro-B to Type A) ▪ Bluetooth 5.0, Class 1 (HFP/HSP/A2DP) ▪ NFC for easy pairin, Audio

Specifications ▪ OmniSound ® HD voice ▪ Speaker:

╶ Frequency response: 100Hz to 20,000Hz ╶ Volume: 90dB (SPL 0.5m) ▪ Microphones: ╶ 4 MEMS

microphones: 100Hz to 7,000Hz ╶ Pickup range: 20ft/6m

▪ Audio expansion: daisy chain connection (future release). ▪ Full Duplex▪ Acoustic Echo

Wireless Cancellation and Noise Suppression, Touch buttons: ╶ Answer call / Power

▪ LED Status Indicators ╶ Power status╶ Call status

╶ Bluetooth status ╶ Battery status ▪ Upgradable Software ▪ Upgradable Software, Integrated

Lithium Polymer Battery ╶ Call time up to 14 hour, Temperature range: 5°- 40°C ▪ Relative

humidity: 20 – 80% condensation-free

Digitally signed by AMIT

Executed Rate Per No. of

Qty Month Months

Active speaker pair of 35 watt, Transducers: LF: 135 mm (5.25 in) low frequency loudspeaker HF:

19 mm (.75 in) Polycarbonate dome tweeter Frequency Range: 80 Hz - 20 kHz Amplifier Power: 35

Watts per channel Maximum SPL Per Pair: 115 dB Crossover Frequency: 4.2 kHz Input Sensitivity:

+4 dBu XLR 1/4"; 0 dBu RCA Signal Input Connectors (x2): Balanced Neutrik* Combo XLR 1/4" TRS;

Unbalanced RCA Power Requirements: 19 VDC / 3.42 A - use only supplied power supply

Headphone Jack: 3.5 mm (1/8") Dimensions: 235 x 159 x 143 mm (9.3 x 6.3 x 5.6 in). tudio quality

transducers for accuracy, and rich bass response: 80 Hz - 20 Khz 35 watt per-channel power

amplifier and high sensitivity drivers produce exceptional output: 115 DB max SPL per pair

Balanced XLR, ¼”, and unbalanced RCA inputs allow connection to a range of signal sources Stereo

23 headphone jack allows monitoring using headphones Ergonomic, side-mounted volume control - Pair 2

simultaneously controls left and right speakers High frequency adjust control - allows the user to

contour HF response to application requirements Magnetically-shielded transducers for use near

CRT monitors and magnetically sensitive equipment Internal peak limiter and overload protection

circuit - protects the system from damage caused by continuous over-driving Wall-mount capable

using optional MTC-2P mounting kit Included snap-on pedestals optimize listening angle for

desktop applications including cabling etc as per instruction of Engineer In charge

Conference Room 9 Pax

75" smart 4K LED Display,Native Resolution 3840 x 2160 (UHD), Brightness Minimum 390cd/m2,

Inputs HDMI-3,USB(3.0)-3,USB-(2,0)-2,OPS Slot-1,RGB-1, LAN-1,SPDIF-1 or Higher, Output

Audio-1( Audio out to connect additional Speakers if required) , Built in Touch type IR spread /P

Cap/Incell/Inglass, Touch Accuracy ±1.5mm or less, Operating System Support Windows

7/8/10/Windows XP/Linux/Mac/Android (Windows XP/Linux/Mac Support one point touch) , Multi

touch point Min 20 Points or Higher, White Board ,Writing, Pen, Palm Eraser ,Save, Screen

Capture, Storage, Tool Bar, Air Class etc , Android 9.0 or better , Internal Memory (32GB),(Hisi 811,

Dual core A73+Dual core A53), DDR(4GB), Wi-Fi, Power Indicator, or higher, Screen Share/Mira

cast to Connect TAB/Mobile, Web Browser , 100-240V~, 50/60Hz, 20W(10W x 2) or higher ,

ISO9001, ISO14001,ISO45001,

Portable USB Video Confrencing camera,PTZ Camera, 20X Optical Zoom, Digital Zoom: Up to 12X

USB Wide Viewing Angle up to 72.5 Degrees, RJ-45 Port, Quiet Motor with Servo Algorithm for PTZ

Camera Control, Full HD 1080p signal output format with a high frame rate of 60 fps, HDMI, and USB 3.0

synchronous video outputs

Digitally signed by AMIT

Executed Rate Per No. of

Qty Month Months

USB: 2.0 (micro-B to Type A) ▪ Bluetooth 5.0, Class 1 (HFP/HSP/A2DP) ▪ NFC for easy pairin, Audio

Specifications ▪ OmniSound ® HD voice ▪ Speaker: ╶ Frequency response: 100Hz to 20,000Hz ╶

Volume: 90dB (SPL 0.5m) ▪ Microphones: ╶ 4 MEMS microphones: 100Hz to 7,000Hz ╶ Pickup

range: 20ft/6m ▪ Audio expansion: daisy chain connection (future release). ▪ Full Duplex▪ Acoustic

Wireless Echo Cancellation and Noise Suppression, Touch buttons: ╶ Answer call / Power╶ End Call ╶

Mic Bluetooth ╶ Volume Up / Down ╶ Mute ▪ LED Status Indicators ╶ Power status╶ Call status ╶

Bluetooth status ╶ Battery status ▪ Upgradable Software ▪ Upgradable Software, Integrated Lithium

Polymer Battery ╶ Call time up to 14 hour, Temperature range: 5°- 40°C ▪ Relative humidity: 20 –

80% condensation-free

Active speaker pair of 35 watt, Transducers: LF: 135 mm (5.25 in) low frequency loudspeaker HF:

19 mm (.75 in) Polycarbonate dome tweeter Frequency Range: 80 Hz - 20 kHz Amplifier Power: 35

Watts per channel Maximum SPL Per Pair: 115 dB Crossover Frequency: 4.2 kHz

Input Sensitivity: +4 dBu XLR 1/4"; 0 dBu RCA

Signal Input Connectors (x2): Balanced Neutrik* Combo XLR 1/4" TRS; Unbalanced RCA Power

Requirements: 19 VDC / 3.42 A - use only supplied power supply

Headphone Jack: 3.5 mm (1/8") Dimensions: 235 x 159 x 143 mm (9.3 x 6.3 x 5.6 in). tudio quality

transducers for accuracy, and rich bass response: 80 Hz - 20 Khz

35 watt per-channel power amplifier and high sensitivity drivers produce exceptional output: 115

DB max SPL per pair Balanced XLR, ¼”, and unbalanced RCA inputs allow connection to a range of

27 signal sources Stereo headphone jack allows monitoring using headphones Ergonomic, side- Pair 1

mounted volume control - simultaneously controls left and right speakers High frequency adjust

control - allows the user to contour HF response to application requirements

Magnetically-shielded transducers for use near CRT monitors and magnetically sensitive

equipment Internal peak limiter and overload protection circuit - protects the system from damage

caused by continuous over-driving

Wall-mount capable using optional MTC-2P mounting kit

Included snap-on pedestals optimize listening angle

for desktop applications including cabling etc as per instruction of Engineer In charge

Digitally signed by AMIT

Executed Rate Per No. of

Qty Month Months

55" smart 4K LED Display,Native Resolution 3840 x 2160, Brightness Minimum 390cd/m2, Inputs

HDMI-3,USB(3.0)-3,USB-(2,0)-2,OPS Slot-1,RGB-1, LAN-1,SPDIF-1 or Higher, Output Audio-1(

Audio out to connect additional Speakers if required) , Built in Touch type IR spread /P

Cap/Incell/Inglass, Touch Accuracy ±1.5mm or less, Operating System Support Windows

7/8/10/Windows XP/Linux/Mac/Android (Windows XP/Linux/Mac Support one point touch) , Multi

touch point Min 20 Points or Higher, White Board ,Writing, Pen, Palm Eraser ,Save, Screen

Capture, Storage, Tool Bar, Air Class etc , Android 9.0 or better , Internal Memory (32GB),(Hisi 811,

Dual core A73+Dual core A53), DDR(4GB), Wi-Fi, Power Indicator, or higher, Screen Share/Mira

cast to Connect TAB/Mobile, Web Browser , 100-240V~, 50/60Hz, 20W(10W x 2) or higher ,

ISO9001, ISO14001,ISO45001,

55" smart 4K LED Display,Native Resolution 3840 x 2160, Brightness Minimum 390cd/m2, Inputs

HDMI-3,USB(3.0)-3,USB-(2,0)-2,OPS Slot-1,RGB-1, LAN-1,SPDIF-1 or Higher, Output Audio-1(

Audio out to connect additional Speakers if required) , Built in Touch type IR spread /P

Cap/Incell/Inglass, Touch Accuracy ±1.5mm or less, Operating System Support Windows

7/8/10/Windows XP/Linux/Mac/Android (Windows XP/Linux/Mac Support one point touch) , Multi

touch point Min 20 Points or Higher, White Board ,Writing, Pen, Palm Eraser ,Save, Screen

Capture, Storage, Tool Bar, Air Class etc , Android 9.0 or better , Internal Memory (32GB),(Hisi 811,

Dual core A73+Dual core A53), DDR(4GB), Wi-Fi, Power Indicator, or higher, Screen Share/Mira

cast to Connect TAB/Mobile, Web Browser , 100-240V~, 50/60Hz, 20W(10W x 2) or higher ,

ISO9001, ISO14001,ISO45001

Portable USB Video Confrencing camera,PTZ Camera, 20X Optical Zoom, Digital Zoom: Up to 12X

Wide Viewing Angle up to 72.5 Degrees, RJ-45 Port, Quiet Motor with Servo Algorithm for PTZ

USB Control, Full HD 1080p signal output format with a high frame rate of 60 fps, HDMI, and USB 3.0

Camera synchronous video outputs

Digitally signed by AMIT

Executed Rate Per No. of

Qty Month Months

USB: 2.0 (micro-B to Type A) ▪ Bluetooth 5.0, Class 1 (HFP/HSP/A2DP) ▪ NFC for easy pairin, Audio

Specifications ▪ OmniSound ® HD voice ▪ Speaker:

╶ Frequency response: 100Hz to 20,000Hz ╶ Volume: 90dB (SPL 0.5m) ▪ Microphones: ╶ 4 MEMS

microphones: 100Hz to 7,000Hz ╶ Pickup range: 20ft/6m

▪ Audio expansion: daisy chain connection (future release). ▪ Full Duplex▪ Acoustic Echo

Cancellation and Noise Suppression, Touch buttons: ╶ Answer call / Power

▪ LED Status Indicators ╶ Power status╶ Call status

╶ Bluetooth status ╶ Battery status ▪ Upgradable Software ▪ Upgradable Software, Integrated

Lithium Polymer Battery ╶ Call time up to 14 hour, Temperature range: 5°- 40°C ▪ Relative

humidity: 20 – 80% condensation-free

Active speaker pair of 35 watt, Transducers: LF: 135 mm (5.25 in) low frequency loudspeaker HF:

19 mm (.75 in) Polycarbonate dome tweeter Frequency Range: 80 Hz - 20 kHz Amplifier Power: 35

Watts per channel Maximum SPL Per Pair: 115 dB Crossover Frequency: 4.2 kHz

Input Sensitivity: +4 dBu XLR 1/4"; 0 dBu RCA

Signal Input Connectors (x2): Balanced Neutrik* Combo XLR 1/4" TRS; Unbalanced RCA Power

Requirements: 19 VDC / 3.42 A - use only supplied power supply

Headphone Jack: 3.5 mm (1/8") Dimensions: 235 x 159 x 143 mm (9.3 x 6.3 x 5.6 in). tudio quality

transducers for accuracy, and rich bass response: 80 Hz - 20 Khz

35 watt per-channel power amplifier and high sensitivity drivers produce exceptional output: 115

DB max SPL per pair Balanced XLR, ¼”, and unbalanced RCA inputs allow connection to a range of

32 signal sources Stereo headphone jack allows monitoring using headphones Ergonomic, side- Pair 4

mounted volume control - simultaneously controls left and right speakers High frequency adjust

control - allows the user to contour HF response to application requirements

Magnetically-shielded transducers for use near CRT monitors and magnetically sensitive

equipment Internal peak limiter and overload protection circuit - protects the system from damage

caused by continuous over-driving

Wall-mount capable using optional MTC-2P mounting kit

Included snap-on pedestals optimize listening angle

for desktop applications including cabling etc as per instruction of Engineer In charge

Digitally signed by AMIT

Executed Rate Per No. of

Qty Month Months

55" smart 4K LED Display,Native Resolution 3840 x 2160, Brightness Minimum 390cd/m2, Inputs

HDMI-3,USB(3.0)-3,USB-(2,0)-2,OPS Slot-1,RGB-1, LAN-1,SPDIF-1 or Higher, Output Audio-1(

Audio out to connect additional Speakers if required) , Built in Touch type IR spread /P

Cap/Incell/Inglass, Touch Accuracy ±1.5mm or less, Operating System Support Windows

7/8/10/Windows XP/Linux/Mac/Android (Windows XP/Linux/Mac Support one point touch) , Multi

touch point Min 20 Points or Higher, White Board ,Writing, Pen, Palm Eraser ,Save, Screen

Capture, Storage, Tool Bar, Air Class etc , Android 9.0 or better , Internal Memory (32GB),(Hisi 811,

Dual core A73+Dual core A53), DDR(4GB), Wi-Fi, Power Indicator, or higher, Screen Share/Mira

cast to Connect TAB/Mobile, Web Browser , 100-240V~, 50/60Hz, 20W(10W x 2) or higher ,

ISO9001, ISO14001,ISO45001,

VC for ED Room cabins:

34 Portable USB Video Confrencing, PTZ Camera, 12x auto focus zoom lens, 360 continuous Nos 5

rotation, high-speed pan and tilt operations.

Active Speakers for ED Room:

Active speaker pair of

Power wattage: 35 watt,

Frequency Range: 80 Hz - 20 kHz

Amplifier Power: 35 Watts per channel Maximum

SPL Per Pair: 115 dB Crossover Frequency: 4.2 kHz

Open Pluggable Specification(OPS):

Intel Core i5 11th Generation, 8GB RAM, 256GB SSD, 1000 mbps gigaLAN, 450 mbps WI-FI,

bluetooth Windows 10 Pro License Pre-Loaded, HDMI 2.0, Mini DP, USB 2.0 x 2 USB 3.0 x 2,

USB C TYPE X1, Audio In, Audio Out

E CAMC of Gass Supression, FF & PA Works:

Digitally signed by AMIT

Executed Rate Per No. of

Qty Month Months

Gas Suppression System

having following Equipments:

Seamless Novec 1230 Cylinder and Valve Assembly, 34

Ltrs. Capacity - 2 Nos.

FM 200 - 60 Kgs

Electrical Actuator for Master Cylinder - 2 Nos.

Discharge Hose - 2 Nos.

Cylinder Low Pressure Switch - 2 Nos.

Nozzles, 360 Deg / 180 Deg Throw - 4 Nos.

Suppression System Piping - 1 Lot

Gas Release Switch/Module - 2 Nos.

Abort Switch - 2 Nos.

Gas Release Panel - 2 Nos.

Make: Ravel/ADN (Including Refilling of Gas per the requirement of complete operation of system)

Fire Fighting System

CAMC of Fire Fighting System having Following Equipments:

Hydrants - 1 Lot

Sprinklers - 1 Lot

Fire Piping and Accessories - 1 Lot

b) Mechanical Foam gas cartridge type. 9 Kg capacity (IS:15683).

c) ABC dry powder stored pressure type 6 kg capacity (IS:15683).

(Including Refilling of cylinders as per the requirement of complete operation of system)

Fire Alarm and PA System

Digitally signed by AMIT

Executed Rate Per No. of

Qty Month Months

CAMC of Fire Alarm and PA System having Following Equipments:

Intelligent analog addressable photothermal detector - 150 Nos.

Response Indicator - 19 Nos.

Addressable fire control module - 4 Nos.

Addressable horn cum strobe - 4 Nos.

Addressable manual call point - 4 Nos.

1.5/3/6W ceiling speaker - 86 Nos.

Digital audio amplifier 75 Watt - 3 Nos.

Voice command keypad 6 zone - 1 No.

Loop Card capacity of 159 detectors For BMS Fire integration - 1 No.

Interface Card for BMS fire integration - 1 No.

Repeater panel - 1 No.

F CAMC of Smart Rack:

1 i-CSR Two smart Racks Solution with 10kW Cooling & 10kW UPS (N+N) Set 1

Server / Network Rack - 800W x 2000H (42U) x 1200D, 100H Base Plinth with A.V pad, Front Glass

Door, Rear Split Plain Door, High Density Vertical Cable Manager & Accessories. 2 nos;

1U Horizontal Cable Manager with PVC channel type 4

Copper Earth Rail 15x5 with screws and insulators 2

Vertical PDU - BASIC & UPS DBBasic Vertical PDU, 30A, 1Ф, 250 VAC, Vertical Rack PDU with “C”

curve 32A single pole MCB with safety guard, power indicator, 16nos of IEC-320-C13 Sockets, 6nos

of IEC-320-C19 Sockets, 2nos of EMO-71-1 6/13Amp Universal Sockets, 6 sq.mm 3 core 4.5 meter 4

cable with NEMA Twist Lock Plug (30A ENP-LD6-30) & Mounting brackets hardware for vertical

UPS DB, 1Phase 32A PDU, with NEMA socket 1 no. & C13 socket 2 nos.,with 32A MCB & PG-16

cable gland,Colour:RAL 9005

In-Rack Cooling System - 10kW (N+N)-

Cooling Unit Module (DX Type, Digital Scroll) - 10kW with Redundancy (N+N)

- Indoor Unit Module with EC Fans

Digitally signed by AMIT

Executed Rate Per No. of

Qty Month Months

Low Side Works for Air-Condition System (15 mtrs dist b/n indoor & outdoor for each 10kW

Environmental Monitoring System with water leaks detection system, temperature & humidity

sensor, Somke Sensor, door sensor & alarm beacon

Biometric Access Control System for Front Rack Door with EM Locks, cabling, bkts etc. 2

Standalone Ultrasonic Rodent Repeller 2

Automatic Door Opening system (For Front Doors) 2

Rack Based Fire Detection & Extinguishing System with FITECH 1230 / FK-5-1-12 Suppression

(2 Rack System)

Electrical Distribution Boards & Cabling Works

Raw Power DB : 19" Rack Mountable Raw Power Distribution Panel with TVSS, Incomer breaker,

Outgoing breakers for Cooling Units, UPS Units, Rodent Repellant, etc.

Cable Trough of size : 300W x 50H mm with Cover Lid & necessary accessories for fixing. 20 mtr

UPS with Battery Bank & STS

10 KVA /10 KW Rack Mount UPS with 1 Phase Input and 1 Phase Output Online UPS ( Model :

External Battery Rack with 15min back-up on full load with all accessories & cables. 2

16A Rack Mountable (1U) STS 16 (Source Transfer Switch) 1

as approved by EIC. Make- Rittal

2 STATIC SWITCH MODULE

Static switch module with microprocessor based control and suitable for linear and non linear load

at particulars distribution board of critical load in event of short circuit overload or any other fatal

condition with built-in Technical Protections like short circuit, Overload, High/Low Voltage cutoff

protection of load from source inclusive of Bypass facility Static Bypass Module is activated during

malfunctioning conditions of load like :-

• Short Circuit

• Bypassing of particular load if required

Digitally signed by AMIT

Executed Rate Per No. of

Qty Month Months

• Resulting in non tripping of main UPS unit • Input Voltage (320-460VAC) 3 phase

• Input frequency 50Hz Indication & Monitoring

• UPS Supply on/source I

• Load on UPS supply/source I

• Main supply on/source II

• Load on mains supply/Bypass

• Bypass Switch on

• Bypass Switch off

complete as required and as per specifications.

Capacity: 63A 3 Phase

G CAMC of CCTV:

5MP IR IP H.265 Vandal Proof Dome camera with 2.8 to 12mm Motorized Lens,Smart IR, up to 30M IR

distance,Up to 120 dB WDR (Wide Dynamic Range),3D DNR (Digital Noise Reduction),H.265+, H.265, H.264,

MJPEG,Corridor mode, Triple streams,3-Axis, IP67, IK10 Vandal Resistant,Colour: 0.005Lux (F1.4, AGC ON), 0

Lux with IR,Video Compression H.265+, H.265, H.264, MJPEG,Behavior Detection Intrusion, Crossing line,

1 Motion detection, Object left, Missing object,Intelligent Identification Face detection, Defocus, Scene Nos 19.00

Change,PoE (IEEE802.3 af) Power consumption: Max 7.2W,Edge Storage Micro SD Card, Up to 256GB, ANR

Support,Working Environment -40°C ~ +60°C, Humidity ≤ 90% RH(Non-condensing),Compatible Integration

ONVIF (Profile S/G), API.

16Ch Embedded Network Video Recorder with 4 Sata Supports 1 × RJ45 1000M ,4K Cameras, HDMI, VGA,

SSD Hard Disk Drive 8TB, 24/7 surveillance category Only complete etc as required.etc.all complete.

55" Flat Screen HD led (24X7) with Interfaces include HDMI, DVI, D-sub, Component and Composite input as

4 well as RS-232C and RJ45 for extensive connectivity, remote control and wall mount unit / floor stand Nos 1.00

complete with making connections etc complete as reqd.

4Ch Embedded Network Video Recorder with 2 Sata Supports 1 × RJ45 1000M ,4K Cameras, HDMI, VGA,

RAID, Redundant power supply, Smart Analytics,

32" Flat Screen HD led (24X7) with Interfaces include HDMI, DVI, D-sub, Component and Composite input as

6 well as RS-232C and RJ45 for extensive connectivity, remote control and wall mount unit / floor stand Nos 1.00

complete with making connections etc complete as reqd.

H CAMC of EPABX

Digitally signed by AMIT