Upgradation of Lighting at Parks in Akhnoor Bhalwal Brahmana.

Approx. weight of Pole 147 Kgs. Base Plate 600 x 600 x 8mm Tensile Test - Tensile Strength 540 Mpa (55 Kgf/Sq.mm). And with Technical Parameters as Physical Requirement The material when tested in accordance with IS: 1894:1972 shall have minimum tensile strength of 42 Kgf/mm and confirming IS 1894: 1972. Protection Against Corrosion. The poles shall be coated with black bituminous paint confirm to IS 158-1968 throughout internally and externally upto the level i.e 1/6 of the total length which goes inside the earth. Tolerance. Outside diameter of poles as nearly circular as possible and their diameter shal l not vay by more than 1%. Earthing. Nut 10 mm dia shall welded on pole at the height of 400 mm from planting depth. The job including provided & fixing of 3C x 2.5 sq. mm copper cable also.

Steel should be of good quality of weight 7.85 g/cum factor of safety on cripplilating load 2 and factor of safety on breaking load is 2.5 size of the base plate duly welded at bottom. The mast shall have 4 No 32 mm dia wholes at 2.54 above the base plate suitable to accommodates 6 to 8 Nos. of 3 core x 2.5 sq.mm Cu conductor cables from control panel to luminaries dia of adjustable ring = 1800mm dia of the steel pipe of the ring =50 mm 4Nos. of support of 50mm dia pipe duly welded between inner periphery of the ring and the cap. The pole is to be errected in c. concretc in the ratio of 1:2:4 mix. The fondation is to be continued upto 2' above groung level in square/round shape. The length and diameter of the cap of the adjustable ring is such that showed be well fixed in top of the mast and give an overall aesthetic look to the mast. The cap of the ring shall have 6 Nos. holes welded suitably with 6 Nos. nuts to facilitate tightening of the top of the mast.

Supplying, Installation, Testing & Commissioning of 150 watt Flood Light, powder coated pressure die cast aluminium body with built in or separate driver as per the requirement with Driver efficiency >85%, Input voltage: Input voltage: 140-270 Volt AC, frequency 50/60 hz, Operating temp range -5 0C to 50 0C, internal surge protection of 5 KV L,N,E as per IEC 61000-4-5, Driver efficiency >85%,THD < 10% as per IEC 61000-3-2, P. F.≥0.95, IP-66,IK-10, CRI >70, under voltage and over voltage protection, EMI-EMC as per CISPR -15, lenses for beam angle 30 deg-120deg as per the application and the project requirement., suitable tilt able fitting, life time (LED, Driver & electrical circuitry) of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report, CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin) , SDCM(Standard Deviation Color Matching) <5, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard complete in all respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥105 <120 lm/Watt output .LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted.. Shape sizeand CCT shall be as approved by Engineer-inCharge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C).

Supplying, installation, Testing & Commissioning of 90 watt Street light LED fixture powder coated pressure die cast aluminium body with driver as per the requirement with Driver efficiency >85%, Input voltage: 140-270 Volt AC, frequency 50/60 hz, Operating temp range -5 0C to 50 0C, internal surge protection of 5 KV L,N,E as per IEC 61000-4-5, Driver efficiency >85%,THD < 10% as per IEC 61000-3-2, P. F.≥0.95, IP-66,IK-10, CRI >70, under voltage and over voltage protection, EMIEMC As per CISPR 15 , lenses for beam angle as per IESNA type I/II/III as per the width of the road and the project requirement., suitable to fit in up to 65mm dia pipe, life time (LED, Driver & electrical circuitry) of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report, CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin), SDCM(Standard Deviation Colour Matching) <5, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard complete in all respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥120 <135 lm/Watt output . LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C).

Design, Supplying, installation ,testing and commissioning of feeder pillar panel (outdoor type) made up of 2mm thick sheet steel, compartmentalized complete with incomer MCCB- FP-40 Amp & out going 10/16 Amp MCB SP 16 Nos., Aluminum bus bar of the required rating, specifications, contactor and timer of suitable rating of reputed make and 3 KVA servo voltage stabilizer complete with UV, OV, Surge Protector single phase tripping, Neutral loss projection and Timer Switch a) Timer Switch = 1 No. b) MCB 6 amp to 32 amp = 8 Nos. c) 1 x 1.5 sq. mm = 10 Mtrs. all other protections & complete as required.

16 sq. mm 4 core

35 sq. mm 3.5 core

Supply, installation, testing & commissioning of maintenance free copper earthing system with 3 mtrs. Electrode 40 mm dia with minium 2mm thick and does not require manual additional of water. The electrode shall be pre-filled with hygroscopic powder and provided with suitable breathing and leaching ports at the ends. the electrode shall be surrounded by suitable powdered form of BEE MOIST so as to provide maximum contact between the electrode and the compund. The compound should be eco-friendly The earthing pit should be covered with PVC cover.