REPAIR MAINTENANCE TO HARDSTANDING FLOORING ROOF JOINERIES AND PERIODICAL WORKS AT ZONE D AREA UNDER GE (EAST) MATHURA

Amount

Dismantling of Asbestos cement (corrugated or semi corrugated etc) sheets in roof covering including ridges, hips, valleys etc complete all as specified and as directed.

S&F Pre-painted galvalume aluminum zinc coating GI based semi-corrugated steel sheet 0.50mm thick (AZ-150) of red colour having tensile strength of 550 Mpa as per IS 15965: 2012 in roof covering/cladding to wall fixed with self tapping screws complete all as specified and as directed.

M&L Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick (AZ-150) of any colour having tensile strength of 550 Mpa as per IS 15965: 2012 as in ridges, hips, valley gutters etc fixed with self tapping screws and sealing the joints of sheet with epoxy complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed.

Dismantling timber scantlings (framed work) 40sqcm and over in section, in any position complete all as specified and as directed.

M&L for Mild steel work as in roof trusses (framed), trussed, purlines, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections, MS hollow pipe) including distance pieces, cleats etc conforming to Fe-410 (Gde-250) quality 'A' complete all as specified and as directed.

M&L for preparation of new steel surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamal paint over and including a coat of red oxide primer complete as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15cm thickness (below or above) ground level complete all as specified and as directed.

M&L 75mm thick cement concrete 1:4:8 type D2 (using 40 mm graded aggregate) as in sub floors, sub bases, floors and paving etc. complete all as specified and as directed.

M&L for 80 mm factory made chamfered edge precast concrete interlocking paver blocks any shape and size of best quality and confirming to IS 15658-2006 , M-30 Grade with grey cement and pigments with appproved colour design & pattern as in footpath, parks, lawan,or light traffic ways of required strength made by table vibratory method using PU mould laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, compacted and proper embedding /laying of inter locking paver block into the sand bedding layer through vibratory compaction by using plate vibrator filling the joints with fine sand and cutting of paver block as per required size and pattern finishing and sweeping extra sand complte grey cement and pigments complete all as specified and as directed.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement : 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and as directed.

Taking down Chowkhats or frames with shutter without taking off shutters from the frames exc. 1.5 sqm but not exc. 4 sqm each complete all as specified and as directed.

Taking down shutters of any description exceeding 1.0sqm and not exceeding 2.0sqm each complete all as specified and as directed.

Taking down shutters of any description exceeding 2.0sqm each complete all as specified and as directed.

S&F factory made single extruded WPC (Wood polymer Composite) solid door/window/ceosetory windows or other frames/chowkhats of size 65mmx100mm (single rebate) comprising of virgin PVC polymer of K value 58-60 (Suspension grade) calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum taxing Index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screw with full body threaded star headed SS screws with full body threaded star headed SS screws having minimum frame density of 750 kg/cum screw withdrawal stength of 2200N (face) & 1100 N (edges) minimum compressive strength of 58 N/mm2 modules of elasticity 900N/mm2 and resistance to spread of flame of class A category with property of being termite/borer roof water /moisture proof and fire retardant and fixed in position with MS hold fast /lugs /SS dash fasteners of required dia and length complete all as specified and as directed. Note : For PVC solid door/window frames, minus 5mm tolerance in dimension i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F factory made single extruded WPC (Wood polymer Composite) solid door/window/ceosetory windows or other frames/chowkhats of size 65mmx125 mm (Double rebate) comprising of virgin PVC polymer of K value 58-60 (Suspension grade) calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum taxing Index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screw with full body threaded star headed SS screws with full body threaded star headed SS screws having minimum frame density of 750 kg/cum screw withdrawal stength of 2200N (face) &1100 N (edges) minimum compressive strength of 58 N/mm2 modules of elasticity 900N/mm2 and resistance to spread of flame of class A category with property of being termite /borer proof, water/moisture proof and fire retardant and fixed in position with MS hold fast /lugs /SS dash fasteners of required dia and length complete all as specified and as directed. Note : For PVC solid door/window frames, minus 5mm tolerance in dimension i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F factory made single extruded WPC (Wood polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade) calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) and 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A catagory with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk stainless steel screws complete all as specified and as directed. Note : Stainless steel butt hinges shall be measured and paid separately under appropriate item(s) of this schedule.

M&L for factory made solid panel wire gauzed wood grain printed PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and wood grain printed PVC sheet for for top rail and bottom rail, wire gauzed i.e panel will be of wire gauze in lieu of wood grain printed PVC sheets panel. The wire gauze shall be wrapped on an additional square 8mm M.S. tubes, The wire gauge shall be stretched to tighten firm, supplying and fixing in the frame at site as per specification & drawing complete all as specified and as directed.

S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as spicified and as directed.

S&F But hinges 100 mm size of stainless steel (SS-203) medium weight, cold rolled complete all as specified and as directed.

S&F aluminium anodised handles of size 150mm, cast type complete all as specified and as directed.

S&F aluminium anodized barrel tower bolts of 200 mm size extruded section and fixed complete all as specified and as directed.

S&F Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts 250mm long of extruded sections or cast aluminium alloy and fixed complete all as specified and as directed.

S&F floor door stopper of aluminium alloy body and tongue anodised with hard drwan steel spring overall length of cover plate 150 mm complete all as specfied and as directed.

Repairing of existing aluminium door single leaf exc 1.00 sqm but not exceeding 2.50 sqm including oiling and greasing of floor springs and making the door and shutter serviceable complete all as specified and as directed. Note : Floor door springs where renewed shall be measured and paid separately under appropriate items of this schedule.

S&F powder coated (minimum thickness and powder coating 50 micron) Anodised aluminium frame for doors, windows, ventilators etc with one or more rebates including joining cleat for fixing etc. complete all as specified and as directed.

M&L for Powder coated aluminium frame (minimum thickness of powder coating 50 micron) work for shutter of doors, windows, ventilators including providing and fixing hinges/pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (fittings shall be paid for separately) with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gask etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/paneling, C.P. brass/stainless steel screws complete all as specified and as directed by Engineer-in-Charge.

M&L for Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around theopening, complete all as specified and as directed.

S&F Sheet glass 5.5mm thick, ordinary quality and glazing in square with aluminium beading exc 0.5 sqm in each pane complete all as specified and as directed.

S&F 100 mm size mortice lock of brass, vertical type,4 levers, complete all as specified and as directed.

S&F aluminium extruded section body Door closer hydraulically regulated, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80kg and fixed complete all as sepcified and as directed.

S&F in repair Aluminium Door seal of overall size 42 mm having nylon brush of 20 mm fixed on aluminium body strip of 22 mm, fixed with screw on Aluminium door, wooden shutters or PVC shutters complete all as sepcified and as directed.

S&F in repair double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and as directed.

S&F in repair aluminium extruded section body Door closer hydraulically regulated, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80kg and fixed complete all as sepcified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L Non skid ceramic ENDURA coloured tiles 10mm thick (square/rectangular) area of each exc 0.11 Sqm but n. exc. 0.18 Sqm as in floors set and jointed in neat cement slurry & pointed with coloured cement to match the colour of tiles laid over and including 15 mm thick screed bed in cement mortar 1:4 complete all as specified and as directed.

M&L for Vitrified ceramic light shade tiles 10mm thick (square/rectagular) polished, area of each tiles not exceeding 0.36 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15 mm thick screed bed in cement motar 1:4 complete all as specified and as directed.

All as per item serial No 37.00 here-in-before but as on vertical surfaces laid over and including 10 mm thick rendering in cement motar 1:3 complete all as specified and as directed.

Dismantling of stone slab of any description and thickness in floors & aprons etc, laid bedded and pointed in any mortar complete all as specified and as directed.

M&L for Machine cut kota stone slab flooring 20-25 mm thick laid over and including 20mm thick screed bed in cement mortar 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

M&L for Kota stone slab 20-25mm thick as in riser of steps, skirting, dado and pillar etc jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete laid over and including 10mm thick rendering in cement mortar 1:3 complete all as specified and as directed.

M&L for 75mm thick cement concrete type C-2 1:3:6 (using 40 mm graded stone aggregate) as in plinth protection, finishing cement concrete surface even and smooth (without using extra cement) compete all as specified and as directed.

M&L for complete removal of existing old treatment from plastered surface of walls and preparation of old plastered surface of walls and applying two coats of weather proof acrylic exterior paint over and including a coat of alkali resistant primer including scaffolding, trestles, ladders, cradles and necessary safety measures for multy storey buildings complete all as specified and as directed.

M&L for complete removal of existing old treatment from plastered surface of walls and applying two coats of distemper oil emulsion, white or tinted over and including 1 mm thick wall care putty complete all as specified and as directed.

M&L for preparation of old plastered surfaces of ceiling and applying one coat of white wash complete all as specified and directed.

M&L for preparation of old plaster surfaces of walls and applying one coat of oil bound distemper complete all as specified and as directed.

M&L for preparation of old painted wooden surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

M&L for preparation of old painted steel surface of any description not otherwise described over 10 cm in width or girth and applying one coat of synthetic enamel paint all as specified and as directed

Taking down cement plaster on brick walls and concrete surface including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and as directed.

M&L for rendering 15 mm thick on other than fair faces of brick work or concrete surface in cement mortar 1:4 finished even & fair complete all as specified and as directed.

M&L for rendering 10 mm thick on fair faces of brick work or concrete surface in cement mortar 1:6 finished even & smooth without using extra cement complete all as specified and as directed.

M&L for rendering 5mm thick on fair faces of concrete surface as in ceiling in cement mortar 1:3 finished even & smooth without using extra cement complete all as specified and as directed.

M&L for prepration of newly plastered surface of walls providing 1mm thick wall care putty to achieve smooth surface and applying two coat of distemper oil emulsion paint over and including a coat of alklai resitant primer complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

M&L for prepration of newly plastered or unplastered surface of walls including cornices, pilars etc and applying two coat of weather proof acrylic exterior paint including scaffolding, trestles, ladders, cradles and necessary safety measures for multy storey buildings complete complete all as specified and as directed.

S&F MS Framed work such as grills gratings, door and cooler stand, etc. with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, railings, framework of water tanks and similar work confirming to Fe.290.Gde-E-165 complete all as specified and as directed.

S&F welded steel wire fabric of weight n exc 4 kg/sqm supplied and fixed complete to wood or steel members complete all as specified and as directed.

Dismantling wall paneling and ceiling boards (fiber, pulp, insulation, etc) or insulation board/slabs/blankets, any thickness, including cover fillets complete all as specified and as directed .

S&F Anodised aluminium snap grid of size 605 x 605mm frame work for false ceiling including Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long for false ceiling and 4mm thick non-asbestos fibre cement building board fixed on aluminium frame work with screws including dismantling of ceiling boards and frame complete all as specified and as directed.

S&F for PVC wall panelling in repair with panel of 300mm x 6mm hollow section of Sintex pattern SPUF-146 or equivalent fixed with PVC plug and screw and inserted to next panel groove, edges and corners of all door/window/openings etc to be covered with PVC angle fixed with solvent cement as per manufacturer's instructions complete all as specified and as directed.

M/S ANIL KUMAR (BID ID -3193136)

JWALA ELECTRIC CONTRACTORS (BID ID -3196021)

DEVI DAYAL CONSTRUCTION CO (BID ID -3197602)

M/S PREETI CONSTRUCTION (BID ID -3197220)

M/s Orient Traders (BID ID -3194198)

B S ENTERPRISES (BID ID -3196959)

Deepak Saxena (BID ID -3197172)

BHARDWAJ CONSTRUCTIONS (BID ID -3195857)