3D Museum - Cuddalore

Amount

Wall Paneling Providing and fixing Acoustic wall Panelling (equivalent ot Armstrong) in channelled wood works perforated panels of width 192mm, thickness of 15mm and length of 2400mm or as per required by the Departmental Engineer made of a high density fibre board with minimum 725 kg./m3 density substrate with a laminated facing as per the approved shade and finish and a melamine balancing layer on the reverse side. The boards shall have a special peforation pattern where the visible surface has a "Helmholtz"fluted perforation of 3mm width and 21mm of visible panel each. The edges of the panels shall be "tongue" and grooved" to receive special clips for installation. The back of the perforated panel shall have sound absorbing not woven acoustical fleese having NRC of 0.52. The panels shall be mounted on special aluminium splines using clips provided by Armstrong and approved by the Engineer-in-Charge...............

Installation: Install aluminium box section (provided by others) of section 50mm x 25mm or as approved by the Engineer-in-Charge on the solid wall horizontally using screws and plugs at spacing of 600mm centre to centre. Screw the aluminium extruded keel for channelled wood works provided by Armstrong over the lowest and second aluminium section at an on centre distane of 600mm. Place the inside clip on the groove end of ht epanel along the aluminium keel and then place the tongue end of the next panel. Continue installing rows of panels by inserting the tongue into groove of the earlier inserted panel and progeressively installing inside clips into the next keel till the actual height in achieved. Finish off the edges using wooden moulding of matching colour (provided by others) Installation to be carried out by Armstrong Trained Installation Team and installation should be carried out as per Armstrong Recommended Procedure

Display Showcase Supplying and Fixing of Arrangement of a Display Showcase at the Size of 8 feet height, 3 feet length, and 1 feet width. Using Materials 18mm, 12mm thick Marine Plywood 1mm Laminated 8mm thick colourless toughened glass with Anti- Reflection coat. As per the following Specification. Provide a bottom box at the size of up to 2.5' in height from the floor finished level 2.5 feet width,3 feet in length. Provide a top box 9 inches in height. all exposed surfaces are covered with 1mm laminate. 8mm thick colourless toughened glass with an anti-reflection coat. provided with an openable door with necessary fittings like hinges, and locks.Provide Slate in 12mm thick colourless toughened glass with Anti- Reflection coat The Rate includes materials, labour, and transportation, etc., as per design. Size — 8 Feet height x 2 feet Length x 12 Inch width - 16' x 5 NO

Pin Board Supplying and Fixing Pin Board at the Size given below. Using materials are 60mm x 40mm x 2mm thick Hollow Aluminum box section, 12mm Cork Board Covered with Fabric Cloth. Back side Covered with 12mm Marine Plywood. The Rate included Transportation, Fixing and Labor Charge Ext., Complete

Pin Board (Size= 6' x 3' )

Pin Board(Size = 5' x 3' )'

Supplying and Fixing the Stage at the size of 20 feet in length, 8 feet in width, and 2 feet in height. As per the following Specification. The materials are 19mm thick marine waterproof Plywood, 50mm 50 mm 2mm thick metal Square tube. Provide structure in 50mm 50 mm 2mm thick metal Square tube at 6m length, 8 feet width, 600mm height to weld it for outer frame. All over are covered with 19mm thick marine waterproof Plywood self thread screw in metal Fabrication.Provide cross bracings in 50mm 50mm 2mm metal Square tube with spacing of 600mm for a length of 2.4m and 50mm 50mm 2mm metal Square tube with spacing of 800mm for a length of 6m. Provide the left and right sides with 2 steps of 3 feet in length and 8 inches in height. The rate Includes Materials, fabricator Labour Charge, Carpenter Labour Charge, and Transportation. Size - 20' x 8' x 2'

Supplying the Handicraft solid wood arm chair cushion. The top is a premium piece of furniture made from genuine Sheesham wood, featuring a durable walnut finish. Water-resitant and fungus-proo. The rate includes transporation

Supply, Installation & Providing of Tip-up recliner chair of center to center 533mm,1020mm height, Plywood (hardwood) with induction heating and high pressure pressed. ABS moulded housing for seat & back cushions,armrest made of PP/PPCP/ABS or semi rigid PU foam. Polyurethane injection moulded flexible foam seat and back density 50 – 55 kg/m3, Fabric to be 100% polyester synthetic fabric with 4 mm polyurethane foam lamination.Fire retardant standard ISO3795, FMVVSS302, Water repellent - Standard -AATCC193. Torsion spring/spring steel IS:4454 1981 Grade III. HRCA/CRCA Sheet metal IS:1079 1994, Electrostatic epoxy powder coating thickness:70 - 80 microns. Seat numbering at side of the chair with LED lights on sides along with aisles.The chairs should be installed to the flooring with the anchor fasteners 12mmx100mm pin type. Fabric colour to customer choice etc., complete

Designing, Printing, and Fixing museum labeling. Provided in Eco Solvent Print Mounted on 3mm Foam Board with Matt Lamination. The Rate including designing charge, Fixing Labour, and Transportation.Ext., complete

Supplying and Fixing of Island Display Showcase at the size of 7 feet Length, 4 feet width, 4.5 feet height. Using Materials 18mm Marina Plywood 1mm Laminate, 8mm thick colourless tough- ened glass with an anti-reflection coat. 2.5 Feet in height from the floor finished level 4 feet width, 7 feet in length. all over four side areas Pasted 1mm laminate. The top cap is Provided with 2 feet height of 8mm thick colourless toughened glass with an anti-reflection coat. Stainless Steel Glass to Glass Bracket is used to connect the two glass. The Rate included Material, Transportation, Fixing, and Labor Charge Ext., Complete.

Supplying and installation of Window Curtain and pelmet, sizes are given as per the following specification. The Materials used are 18mm plwood and 1mm Laminated. Provide a Pelmet in 18mm plywood, all exposed areas are pasted with 1mm laminate, at the size of 4 feet in length, 4 inches in height, and 5 inches in width. provide window curtains in premium Polyester fabric. Tailored- made with pleat drapes. provide Clip Rings with Hooks and Stainless steel pipe. The Rate included Material, Transportation, Fixing charge ext., Complete.

Making up Clay models of Pichavaram Landscape. The mold is taken in Plaster of Praise Material over the formed Figer. The place where the mold is taken is filled with 2-layer fiberglass material and then the model is made with a thickness of 4mm. The model will be Rubbed with Fine Sand Paper. The model is Clean washed with Soap oil, and Painted with 1 Coat of Duco Primer. The Model is Painted with an Acrylic multi-color paint finish with a spray gun and the Artist's Manual work. Water Effect provide in Epoxy Resin Materials. 3-D printing technique shall be used as required in the model. Make a Leaves in Fabric Cloth Materials by Manual and Stencil Cut. Provide Fabric Dye Colours in Leaves, and Acrylic multi-paint finish with a spray gun. Leaves are arranged by Manual Work.The Rate included Material, Model Maker Charges, Transportation, Fixing, and Labor Charge Ext., Complete.Size - 7' x 4' x 12 Inch height

Making up Clay models of Chidambaram temple Gopuram, Statues, and Pillars. The mold is taken in Plaster of Praise Material over the formed Figer. The place where the mold is taken is filled with 2-layer fiberglass material and then the model is made with a thickness of 4mm. The model will be Rubbed with Fine Sand Paper. The model is Clean washed with Soap oil, and Painted with 1 Coat of Duco Primer. The Model is Painted with an Acrylic multi-color paint finish with a spray gun and the Artist's Manual work. The water Effect is provided in Epoxy Resin Materials. 3-D printing techniques shall be used as required in the model. Other materials including metal, wooden plastic boards, foam boards, acrylic sheets, cardboard, sponges, etc. shall be used as needed for the model. Provide LED Lights in the Model. The Rate included Material, Model Maker Charges, Transportation, Fixing, and Labor Charge Ext., Complete. Size - 7' x 4' x 12 Inch height

New 3D Mural Panel to Display Museum Artifacts in Cuddalore District. Making up Clay models. The mold is taken in Plaster of Praise Material over the formed Figer. The place where the mold is taken is filled with 2-layer fiberglass material and then the model is made with a thickness of 4mm. The embossed figure is approximately 8 inches. The model will be Rubbed with Fine Sand Paper. The model is Clean washed with Soap oil, and Painted with 1 Coat of Duco Primer. The Model is Painted with an Acrylic multi-color paint finish with a spray gun and the Artist's Manual work. Provide All over 4 side 3-inch Carnish Boarder in the Panel. Bakside the panel Provide 12mm plywood. The Rate included Material, Model Maker Charges, Transportation, Fixing, and Labor Charge Ext., Complete. Size — 6’ x 3' - 18' x 2 NO

Display Arrangement with Suitable Materials to display objects Metal Rod, Acrylic Bar, Acrylic Sheet, and Some other Hanking Technical Display Materials

Size - 12” x 8” - 3mm Acrylic L Shape Stand

Size - 8” x 6” - 3mm Acrylic L Shape Stand

Size - 7” x 5” - 3mm Acrylic L Shape Stand

Size - 4” x 4” - 2 Inch Acrylic Bar

Size - 4” Inch Dia x 4 inch height - 3mm Acrylic Cylinder

Supplying and Installation the Seating Riser Platform at a size of 24 feet in length, 20 feet in width, and 18 inches in height. As per the following Specification. The materials are 70mm x 40mm x 3mm thick MS Rectangular Hollow Section for Frame Leg for 3 different height 6 inches, 12 inches and 18 inches.The platform is built in 3 different height of size 20' x 8'x 6", 20'x8'x12" and 20'x8'x18" and weld together. 50mm x 50mm 2.5mm thick MS Square Hollow Section for outer frame and inner cross bracings, and 19mm thick waterproof Marine Plywood. Make a Frame in 70mm x 40mm x 3mm thick MS Rectangular Hollow Section as Leg, 50mm x 50mm 2.5mm thick MS Square Hollow Section for outer frame and inner cross bracing with spacing of 600mm along the 2.4m length and 800mm spacing along the 6m length.The 1st frame is set 6 inches above the ground level, the 2nd frame is set 18 inches above the ground level and the 3rd frame is set 18 inches above the ground level and to weld together. All weld areas are rubbed with a grinding machine to have a flat surface. Apply 1 coat of Metal Primar and 2 coats of enamel paint all over the metal Frame. The Metal Frame top and Side are covered with 19mm thick Water Proof Marine Plywood with Silicone Paste and Self thread Screw. The Rate Includes Materials, fabricator Charge, Carpenter Charge, and Transportation. Size 20' feet Length x 24' feet width x 1.5' feet height

S.R.CONSTRUCTION (BID ID -1423543)

SS Associates (BID ID -1423627)