REPAIRS TO JOINERY FLOORING FALSE CEILING SANITARY FITTINGS AND CLEANING OF WATER TANKS FOR CERTAIN OTM ACCN OF NO 2 ATC SOUTH UNDER GE CENTRAL BANGALORE

Amount

Taking down cement plaster of any description including racking out joints, hacking for key scrubbing down with water etcand removal of entire debris as ordered outside MD land complete all as directed.

Demolition of cement concrete (un-reinforced) in ground floor and paving not exc 15 cm thick above or below ground level and removal of entire debris as ordered outside MD land complete all as directed.

Dismantling floor, hearth or wall tiling inluding cement mortar bedding (but not backing), stacking serviceable tiles at site and removal of entire debris as ordered outside MD land complete all as directed.

Demolition of stone slabs and tiles of any description or thickness in floors, platform, aprons etc., laid, bedded and pointed in any mortar including stacking serviceable slabs at site and removal of entire debris as ordered outside MD land complete all as directed.

Taking down chowkats or frames not exc 1.5 sqm each with shutters (without taking off shutters from frame) and stacking at site where directed.

All as per item 5 here-in-above but exceeding 1.5 Sqm but not exceeding 4 Sqm each

Taking down shutter of any description area not exc 1.00 sqm Sqm each and refixing in the same opening after cutting , easing and adjustmentas with old ll types of builders hardware complete all as directed.

Taking down shutter of any description n.exc 1 Sqm each and stacking at site where directed.

Re-screwing or easing & adjusting without taking down shutter of any description exc 1Sqm & n.exc 2 Sqm.

M & L for PCC 1:5:10, type E2 using 40 mm graded crushed stone aggregate as in mass concrete filling sunken floor or other description as ordered complete all as specified and directed

Supply only Integral Water Proofing Compound (ISI Marked) of Make : CICO , Acco Proof , Impermo , Aqua flex as approved.

S &F 35 mm thick second class hard wood factory made glazed and skeleton shutter open rebated and prepared to receive glass, guage etc edge of framing plain chamfered or rounded fitted with cut and mitred beads for securing guage etc size of members of shutter as specified in SSR Part I Section 8 clause 8.24 (a) supplied and fitted to chowkats.

S&F 35mm thick Flush shutters, veneered solid core construction, with block coard core & plywood face panels commercial type on both side conforming to IS 2202 (Part- I) -1999, including internal liping beading all round fixed as in Door Shutter,Cup board shutter & Kitchen rack all as specified.

S&F factory made pressed steel frames of size 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, mild steel sheet of 1.25 mm thickness, complete as specified & as directed

S&F factory made pressed steel frames of size 105x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, mild steel sheet of 1.25 mm thickness, complete as specified & as directed

S&F solid PVC door frame of size 50X47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube supplying and fixing in opening as per specification all as directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with plain colour single piece extruded PVC profile ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour single piece extruded PVC profile for top rail lock rail bottom rail on either side and as gap insert for Top rail and bottom rail paneling of plain colour PVC sheet to fitted on the MS frame welded/sealed to the styles and rails with suitable PVC sheet beading and joined together with solvent cement complete all as specified and as directed..

S & F 150 mm long aluminium, anodised , barrel tower bolt (ISI marked) of extruded section and fixed.

S & F in repair 150 mm long aluminium, anodised , barrel tower bolt (ISI marked) of extruded section and fixed.

S&F100 mm size butt hinges, medium weight cold rolled mild steel and fixed .

S&F in repair 100 mm size butt hinges, medium weight cold rolled mild steel and fixed .

S&F in repair aluminium alloy handles 150 mm long (ISI Marked)cast type anodised and fixed.

S&F aluminium alloy handles 150 mm long (ISI Marked) cast type anodised and fixed.

S&F 300 mm long aluminium alloy, anodised sliding door bolt (ISI Marked) with hasp, staple (bolt type) and fixing clip of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed.

S&F in repair 300 mm long aluminium alloy, anodised sliding door bolt (ISI Marked) with hasp, staple (bolt type) and fixing clip of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed.

S&F in repair 300 mm long aluminium alloy, anodised sliding door bolt (ISI Marked) with hasp, staple (bolt type) and fixing clip of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed.

S&F in repair aluminium die cast body door closed hydraulically regulated designation No. 2 universal type (ISI Make) suitable for door shutters of weight between 36 to 60 Kg complete all as specified. Make :- Everest/Prabhat/or equivlent

S&F 150 mm long aluminium anodized floor door stopper double legged with rubber shoe/boot, fixed to bottom rail of door shutter complete all as specified & as directed.

S&F in repairs 150mm long aluminium anodized floor door stopper double legged with rubber shoe, fixed to bottom rail of door as directed. Note :- Door stopper shall be conforming to the sample kept in GE’s office.

S&F in repairs powder coated mild steel drapery rod of 25 mm inner dia (in lengths as directed) of approved colour with & including decorative finial at both ends and pair of powder coated mild steel brackets fixed at both ends with PVC rawl plug & steel screws on walls/beam, including PVC curtain rings of matching colour @ 10cm C/C all as specified & as directed

S&F in repairs stainless steel wire cloth, 0.24mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples including supply & fix second class hard wooden fillet, wrought, cross sectional area exceeding 3 Sqcm but n.exc 6 Sqcm fixed with nails complete all as directed.

S&F stainless steel wire cloth, 0.24mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples including supply & fix second class hard wooden fillet, wrought, cross sectional area exceeding 3 Sqcm but n.exc 6 Sqcm fixed with nails complete all as directed.

S&F Powder coated Aluminium windows sliding windows with frame jointing cleat for fixing ect. and aluminium anodised skeleton windows & shutter fixed with glass or gauge sliding type (Three track frame section exc 0.98kg/m) without using sash bars using standard aluminium section ( shutter section weight not less than 0.45 Kg/Rm ) jointing cleats, glazing clips, rubber packing, anodised aluminium snap, beading screws, anodised aluminium fittings such as handles stainless steel adjustable friction stay hinges etc complete all as directed. Note:- The unit rate quoted shall be inclusive of cost of rubber beading fitting such as handles SS friction stav hinges.

S&F Powder coated Aluminium ventilators/ louvers with frame jointing cleat for fixing etc and aluminium section jointing cleat for fixing etc and aluminium anodised fixed with glass or gauge without using sash bars using satndard aluminium section jointing cleats, glazing clips, rubber packing, anodised aluminium snap, beading screws, etc complete all as directed. Note:- The unit rate quoted shall be inclusive of cost of rubber beading and neccessary fittings

S&F anodized aluminium frame for doors, windows, ventilators, partitions, powder coated of any colour as approved (Thickness or powder coating not less than 50 micron) with one or more rebates including joining cleat for fixing etc. complete all as specified & as directed

S&F anodized aluminium door shutters, aluminium section weighing 0.55 kg/m, powder coated of any colour as approved (Thickness or powder coating not less than 50 micron) including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodized aluminum snap beading screws etc. complete all as specified & as directed

Dismantling of any type of false ceiling including any thickness of ceiling board & Supply and fix anodized aluminium snap grid of size 605mm x 605mm frame work for false ceiling & provide 12mm thick non asbestos fibre cement building board board/tiles of size 600mm x 600mm in size, fixed with staples on snap grid complete all as directed.

M&L for applying evenly two coats of blown type bitumen at the rate of 1.50 Kg per sqm and blinding with clean dry sand @ 0.005 cum per sqm complete all as specified & as directed

M & L for 75 mm thick plain cement conctere 1: 3 : 6 type C2 using 40 mm graded crushed stone aggregate as in plinth protection finished the surface fair and even complete all as directed.

M&L for rendering 15 mm thick in CM 1:6 on brick work/ stone work or concrete surface work finished even and smooth without using extra cement complete all as specified.

All as per item No 40 here-in-above but 10mm thick in CM 1:3 on ceiling,chajja,roof projection etc.

M & L for rendering 15 mm thick in cement mortar 1:4 on fair faces of brick work/ stone work or concrete surfaces mixed with WPC as per manufacturer instruction , and finished the surface fair and even complete all as specified and directed.

M & L non-skid coloured joint free non-skid ceramic tiles 7 to 8 mm thick (square/ rectangular), area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with tiles laid over and including 10 mm thick screed bed in cement mortar 1:4 complete all directed and specified.

M&L glazed ceramic designer tiles any shade or pattern as approved of size 450x350x7 mm thick, on verticals surfaces, set and jointed in neat cement slurry including 10 mm thick back coat in CM 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all directed. (Note for item Nos 43 & 44 : i) Quoted rate is deemed to be inclusive of cement screed. ii) Shade / pattern / Colour of tiles shall be got appproved before procurement).

M&L for 18-20mm thick Sadherhali stone slab flooring, steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granit laid over and including 15 mm thick screed bedding in cement mortar 1 : 4including Rounding to edges complete.

All same as per item No 45 here - in - above but as in dado & skirting with 10 mm thick 1 : 3 cement mortar screed - do -(Note for item No 44 to 45 : i) Quoted rate is deemed to be inclusive of cement screed.)

Three coats of white wash on newly plastered surface of ceiling after necessary preparation of surface complete all as directed

M&L preparing of newly plastered wall surface and & applying two coats of cement base paint over a coat of alkaline resistant primer complete all as directecd.

M&L preparing new plastered wall surfaces and applying two coats of oil bound distemper over a coat of alkali resistant primer over a coat of 3 mm thick white cement based wall care putty as ordered complete all as specified.

Hacking out old broken glass (any thickness) and size from wooden frame glazed with putty or fixed with wooden beads and removal of debris to a distance n.exc 50 mtr and depositing where directed.

S&F sheet glass 4mm thick glazing with oil putty or wooden beads not exceeding 0.5 Sqm in each pane complete all as directed.

S&Fin repair sheet glass 4mm thick figured glass, pin headed type and glazing with oil putty or wooden beads not exceeding 0.5 Sqm in each pane complete all as directed.

M & L Two coats of 1st quality synthetic enamel paint over a coat of pink primer on new wooden surface of any description over 10 cm in width or girth including necessary preparation of new wooden surface complete all as directed.

M & L Two coats of 1st quality synthetic enemal paint over a coat of zinc chromate primer over any description of new steel surface over 10 cm in width or girth including necessary preparation of new steel surface complete all as directed.

Taking down old 20 mm bore GI tubing and connection including cleaning for re fixing stacking at site where directed.

All as per item No 55 here-in-above but 25 mm bore of pipe -do-

S&F CPVC pipe SDR II having outer dia 20 mm pipe with plain CPVC SDR II fitting such as bends, elbows, unions and end pieces to receive the fittings and fixed with solvent cement in walls/ceilings (concealed/surface) or laying in floors complete all as specified

All as per Item No.57 here-in-above, but 25 mm outer dia pipe.

S&F in repairs 15 mm bore bib taps of PTMT white colour , screwed down high pressure with crutch or butterfly handle , screwed for iron pipe or for unions and fixed complete all as directed. Make: Prayag or equvalent make approved by GE.

S&F in repairs 15 mm bore bib taps, fancy type long body with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as directed. Make: Prayag 6509 or equvalent make approved by GE.

S&F in repairs 15mm bore pillar tap, cast copper alloy with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks & fly nuts, screwed for iron pipes complete all as specified & as directed.

S&F in repairs Gun metal gate or gate valves with iron wheel head screwed box and both ends for iron pipe for 20 mm bore of pipe or union complete all as directed.

S&F in repairs Gun metal gate or gate valves with iron wheel head screwed box and both ends for iron pipe for 25 mm bore of pipe or union complete all as directed.

S&F in repairs brass spindle suitable for 15 mm bore stop cock concealed type make & type as per existing one or as ordered .

S&F in repairs 15 mm bore stop valve fancy type, cast copper alloy, chromium plated, with long shank and cup (concealed type) screwed down high pressure with cruntch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified. Make: Prayag Cat No. 6518 or equivalent in approved make.

S&F in repairs stop valves for 15 mm bore of pipe cast copper alloy, screwed down, high pre-ssure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified.

S&F in repairs 15mm bore Angle stop valve, fancy type with long shank and cup (concealed type) of cast copper alloy chromium plated, screwed down, high pressure with capstan heads, screwed both ends for iron pipe or for union complete all as specified & as directed.

S&F in repairs brass chromium plated shower rose 125 mm dia with or wihout swivel joint, any size, including fixing to steel pipe or union.Make : Prayag or equivalent as approved.

S&F new sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or cutting and fixing into granite platform including fixing cantilever brackets and connecting union to pipe overall size 915 x 460 mm bowl size 410mm x 330mm x 150mm complete all as directed

Supply and fixing in repair 32mm dia waste fittings brass CP fixed to WHB complete all as spd and directed by Engg-in-Charge

All same as per item No 70 here-in-above but 40mm dia suitable for sink etc

S&F in repair PVC syphon with knob for PVC flushing cistern of 10 Ltr of capacity all as specified

Supply and fixing repair stainless steel grating 125mm dia as suitable to existing trap as per requirement all as spd and directed by Engg-in-Charge

S&F in repairs Grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40gms).

Taking out damaged pipe any dia & type after necessary excavation & S & F 110 mm bore PVC (SWR) pipes single socketed in any length with rubber rings joints laid in excavated trenches & testing on completion complete all as directed.

All same as per item No 76 here-in-above but 75 mm bore of pipe -do- (Note for item No 73 & 74 : Quoted rated is deemed to be inclusive of earthwork & excavation)

S & F 110 mm bore PVC (SWR) pipes single socketed in any length with rubber rings joints fixed to wall in repars complete all as directed.

All same as per item No 78 here-in-above but 75 mm bore of pipe -do-

S&F 110 mm bore size PVC (SWR) junction single(single T) equal or unequal with access door including jointing the same with solvent cement complete all as directed.

All as per item No 80 here -in -above but 75mm bore.

S&F PVC (SWR) Vent cowl 75 mm bore size fixed complete all as directed.

S&F PVC (SWR) Vent cowl 110 mm bore size fixed complete all as directed.

S&F 550 mm X 400 mm size white flat back vitreous china wash hand basin including chromium plated pillar tap (Make: Prayag Cat No. 6502) cap stain head suitable for 15 mm bore of pipe , PVC connection 15 mm dia 45 cm long with chromium plated nuts and bolts and suitable washers, PVC waste 32 bore CP waste coupling chain and plug , porcelain stopper including CI bracket fixed in repair complete all as diirected.

S & F in repairs Vitreous china squatting pan "Orissa pattern" long pan of size 580 x 440 mm white with integral foot rest, with ‘P’ or ‘S’ trap, front or back inlet but (excluding flushing cistern and flush pipe ) including connection etc including setting the trap and pan in lime concrete ( 1 lime 2 sand or surki as ordered and 5 aggregrate ) , min. 150 mm thick alround and finished just below level of rim of pan to floor finish complete all as directed.

S & F in repairs PVC seat cover for EWC white colour complete with MS Hinged cromium plated make as per existing all as specified and as directed

S & F in repairs, vitreous China wash down water closet pan (pedestal pattern), white, including connection to outgoing drain and 32mm dia flush pipe,flushing pipe, anti syphonic pipe with and including white PVC seat and cover closed pattern with flat bottom and MS chromium plated hinging device including provision of 10 ltr capacity low level PVC Flushing cistern, PVC connection pipe, 15 mm dia, 600 mm long complete including making good damaged/disturbed surfaces complete all as specified and directed. Make of Pan CERA Cat No S1053101/S1053102 and of cistern B1010109 or equivelent of Parryware/Hindware/Prayag

S&F in repairs 10 liters capacity PVC valveless, syphonic action type, flushing cistern, low level, white with inlet ball valve, float and handle including brackets and flush pipe of polyetylene of low or high density or 32 mm dia PVC connection pipe complete all as directed.

S&F in repairs ball brass valves high pressure with PVC float and fly nut complete screwed for iron pipe or brass ferrule and fixed with 20mm dia

S&F in repairs PVC connection 15mm bore and 45cm long with two Nos of PTMT check nuts and washers complete all as directed. Make : RRAYAG or equivalent as approved

S&F in repairs PVC connection 15mm bore and 60cm long with two Nos of PTMT check nuts and washers complete all as directed. Make : RRAYAG or equivalent as approved

M & L for Cleaning & removing all dirt and scale from water storage tank of capacity exe 250 ltr and n.exe 500 ltr hoisted & fixed in any description & height and also from mouth of pipe of tank comple to satiisfaction of Engiineer-in-chharge .

All same as per item No 92 here-in-above but tank of size exc 500 lts but not exc 1000 lts -do-

All same as per item No 92 here-in-above but tank of size exc 1000 lts but not exc 2000 lts -do-

Dismantling of existing any type & any capacity water storage tank fixed in any description and stacking at site and S&F new 500 litres capacity (white colour) rotational moulded polythene water storage tank, (cylindrical vertical with close top) triple layer colour white both inside and outside with top cover including PVC float valve high pressure suitable for 20 mm bore of pipe with polythene float, fixture hoisted and fixed in position where ordered and making necessary connection and testing complete all as directed.

Dismantling of existing any type & any capacity water storage tank fixed in any description and stacking at site and S&F new 1000 litres capacity (white colour) rotational moulded polythene water storage tank, (cylindrical vertical with close top) triple layer colour white both inside and outside with top cover including PVC float valve high pressure suitable for 25 mm bore of pipe with polythene float, fixture hoisted and fixed in position where ordered and making necessary connection and testing complete all as directed.

Removing complete shrubs/ vegetation upto root grown in any description such as grown in wall / beam / roof /chajja etc in height up to three storey building including filling the holes where the shurbs removed with cement concrete 1:2:4 type B-0 (12.5mm graded stone aggregate) of minimum size 15cm x15cm x 15cm or as required and making good the distured surface as per its original specification to the satisfaction Engineer-in-charge& removal of the taken out shurbs out of MD land and disposed complete all as directed.

docileworx (BID ID -3092301)