Lifting Cutting Flushing Lowering and repairing of submersible pump including repairing of pipe line network and misc. Works at Pouni II Expansion OCM under Pouni Sub Area

Amount

Lifting of Submersible pump with motor & GI Column pipe etc including all arrangement like wich tripod , chain pully and other necessary arrangement for lifting the same as per direction of Engineer incharge.

Lowering of Submersible pump with motor & GI Column pipe etc including all arrangement like wich tripod , chain pully and other necessary arrangement for lowering the same as per direction of Engineer incharge.

Repairing and Rewinding of Submersible pump & Motor 5.00 HP including bushing , oil seal , ball bearing , bush impeller etc with all miscellaneious GI fitting and labour charges etc complete as per instruction of Engineer Incharge

Repairing and Rewinding of Submersible pump & Motor 3.00 HP including bushing , oil seal , ball bearing , bush impeller etc with all miscellaneious GI fitting and labour charges etc complete as per instruction of Engineer Incharge

Cutting, flushing and repair of Bore well 150 mm to 200 mm dia i/c with cutting machine , labour , etc complete

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.

Filling available excavated earth (excluding rock) in trenches, plinth. sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited ayer by ramming and watering, lead up to 50 m and for all lift

Clearing grass and removal of the rubbish up to a distance of 50 m outside the periphery of the area cleared.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

Brick work with Fly ash cement bricks in foundation and plinth : Cement mortar 1:6 (1 cement : 6 coarse sand)

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 80 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 50 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work . 25 mm dia nominal bore

Providing ISI MarK G.I. pipe of following class and dia excluding GST levied by GOI & GOM in all respect , inspection charges , transportation to stores etc complete as per IS -1239 /2004 NOTE : one coupler shall be provided with each full length of pipe cost of which is included in rates below.Heavy 50 mm ( 6.24 Kg/ M )

Lowering , laying and jointing G.I. pipe and specials of following class and diameter including conveyance from store to site of work , all labour etc complete either underground or in verticle position as directed by Engineer incharge. Heavy 50 mm dia (6.24 Kg/M)

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on wall 25 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on wall 15 mm dia nominal bore

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work . 25 mm nominal dia Pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in harge. External work 20 mm nominal dia Pipes.

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 50 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 25 mm nominal bore

Providing and fixing G.I. Reducer 50mm x 40 mm dia etc complete

Providing and fixing G.I. Nippal 40 mm dia with 75 mm length etc complete

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 25 mm nominal bore

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.15 mm nominal bore

Providing and fixing PTMT bib cock of approved quality and colour. 15mm nominal bore, 86 mm long, weighing not less than 88 gms

Providing and fixing PTMT pillar cock of approved quality and colour. 15 mm nominal bore, 107 mm long, weighing not less than 110 gms

Providing and fixing white vitreous china pedestal type water closet(European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Flat back wash basin size 550x400 mm with single 15 mm C.P. brass pillar tap

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern,with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS :2556, C.I. trap with outlet grating and other couplings in C.P. brass,including painting of fittings and cutting and making good the walls and floors wherever required : Single half stall urinal with 5 litre P.V.C. automatic flushing cistern

Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete. 10 litre capacity - White

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Semi rigid pipe 32 mm dia

Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour. 15 mm nominal bore with 45 cm length

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing and supplying in standard lengths Polyethelene Pipes, confirming to IS 4984 / 14151 / 12786 / 13488 with nesessary jointing material like mechanical connector i. e. thread / insert joint / quick release coupler joint / compression fitting joint or flanged joint excluding coupler/specials, including transportation and freight charges, inspection charges, loading / unloading charges, conveyance to the departmental stores & stacking the same in closed shade duly protecting from sunrays & rains, excluding GST levied by GI & GOM in all respect etc. complete PE-100,8 Kg/Sq.cm 63 mm

Lowering,Laying,and Jointing H.D.P.E./M. D. P. E. pipes in proper position including all specials by compression fitting/electrofusion and butt fusion jointing procedure as per relevent IS Code complete with all materials for jointing procedure like Electrofusion machine, Electric heater/butt fusion welding machine with hydraulic jack, top loading clamp etc. and all labours as directed by engineer in charge as per IS-7634 Part II For all classes. 63 mm

Providing and supplying ISI mark CI D/F reflux valves (non-return valves ) of following dia including railway freight, inspection charges, unloading from railway wagon, loading into truck, transportation upto departmental stores, unloading, stacking excluding GST levied by GOI&GOM in all respect etc.complete. Reflux valves as per I.S.5312 Part (1984). With out by pass arrangement -PN-1 80 mm

Providing double flange sluice valve confirming for IS- 14846 including worn gear arrangements as per test pressure, stainless steel spindle, caps, including inspection charges, transportation upto departmental store, unloading, stacking excluding GST levied by GOI & GOM in all respect etc. complete. Without by pass arrangement-PN-1 80 mm

Providing double flange sluice valve confirming for IS- 14846 including worn gear arrangements as per test pressure, stainless steel spindle, caps, including inspection charges, transportation upto departmental store, unloading, stacking excluding GST levied by GOI & GOM in all respect etc. complete. Without by pass arrangement-PN-1 50 mm

Lowering, laying and jointing in position following C.I.D/F Reflex valves, Butterfly valves and Sluice valves including cost of all labour jointing material, including nut bolts and giving satisfactory hydraulic testing etc. complete.(Rate for all class of valves.) 80 mm

Lowering, laying and jointing in position following C.I.D/F Reflex valves, Butterfly valves and Sluice valves including cost of all labour jointing material, including nut bolts and giving satisfactory hydraulic testing etc. complete.(Rate for all class of valves.) 50 mm

Making connection of G.I. distribution branch with G.I main of following sizes by providing and fixing tee,including cutting and threading the pipe etc. complete: 50 to 80 mm nominal bore

Making connection of G.I. distribution branch with G.I main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete: 25 to 40 mm nominal bore

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing 100 mm dia stabiliser pipe/P.V.C.soil vent/waste pipe and with necessary fixture sand fitting such as bends,tees,single junctions,slotted vent,clamps etc. complete.

Providing and fixing 10 cm PVC nahani trap with grating etc. complete

Supplying, erecting, testing and commissioning of flat flexible 3 core 6 sq.mm PVC sheathed submersible type copper cable suitably clamped at fixed intervals with column pipe assembly complete.

Providing and fixing G.I. 50 mm dia Flange joint with a pair of flange including Nut bolt and rubber packing etc complete as per instruction of engineer incharge.

Providing and fixing G.I. 80 mm dia Flange joint with a pair of flange including Nut bolt and rubber packing etc complete as per instruction of engineer incharge.

Providing and fixing ISI mark rain gun 1.5 " ( 40 mm ) dia inlet connection with both full and part arrangement adjustable jet breaker to provide uniform raingun capable of delivered / descharge 1.03 lps to 5.18 lps with radius of coverage 16.2 -30 meter including all cost complete .

Providing erecting main suspension by nylone rope of 22 mm dia. Having terminal in provided eye bolts etc. complete.

Cutting of 50 mm dia Exist GI Pipe & threding of pipe & P/F 50 mm dia G.I. coupler Heavy

Total impact of GST for the purpose of CTC

P S Salve (BID ID -1147446)