PROVISION OF TOILETS AND BATHROOMS NEAR BLDG NO. T-561 AND, SPECIAL REPAIRS TO CHEQUERED TILE PATH FROM T-244 TO P-113 AT RONGLI AND PROVISION OF CERTAIN REVENUE WORKS AT RHENOCK AND RONGLI UNDER GE 867 EWS

Amount

Excavating in trenches, not exceeding 1.5m wide and not exceeding 1.5m in depth; for foundation, laying of pipe, cable etc., or for shafts, wells, cesspits, manholes, pier holes, etc., not exceeding 10 sqm on plan and getting out in soft/loose soil all as specified and directed by Engineer-in-charge.

M&L for Plain cement concrete 1:4:8 mix type D2 (using 40 mm graded stone aggregate) in foundations, filling and mass-concrete etc., all as specified and directed by Engineer-in-Charge.

M&L for factory made precast cement block masonry with solid blocks made of Plain cement concrete 1:3:6 mix type C1 (using 20 mm graded stone aggregate) exceeding 10cm width and setting in cement mortar 1:6 complete all as specified and directed by Engineer-in-charge. Make : Shankar Saw Mills/Sangam Prefeb Products or equivalent make as approved by GE.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm in soft/loose soil complete all as specified and directed by Engineer-in-charge.

Removing surplus excavated soil to a distance not exceeing 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed by Engineer-in-charge.

M&L for Hardcore with Broken stone/boulders of gauge not exceeding 63mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface all as specified and directed by Engineer-in-charge.

M&L for 75 mm thick Plain Cement Concrete 1:4:8, type D2 (using 40mm graded stone aggregate) as in sub base and finishing even and rough to receive toping layer complete all as specified and directed by Engineer-in-charge.

M&L for rendering 15 mm thick on brickwork or concrete surfaces in cement mortar 1:4 finished fair and even including waterproofing compound @ 3% by weight of cement as per manufacturer's instructions complete all as specified and directed by Engr-in-charge.

M&L for rendering 15 mm thick on brickwork or concrete surfaces in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and directed by Engr-in-charge.

M&L for preparing newly plastered surfaces of walls and applying three coats of white wash complete all as specified and directed by Engineer-in-charge. Make: LOVELYCEM/ SURYACEM/ JANATHACEM / LUCKYCEM or equivalent make as approved by GE.

M&L for preparation of new surfaces of walls and applying two coats of cement base paint over one coat of primer complete all as specified and as directed by Engineer-in-Charge. Make: INDOCEM/ SUPERSNOWCEM/ AQUACEM/ DURACEM

M&L for non skid ceramic coloured tiles 7 to 8 mm thick square/rectangular area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors etc., jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles laid on and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed by Engr-in-charge.

M&L for coloured glazed ceramic tiles of size 450x300x7mm thick on vertical surfaces such as skirting/dado, jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles laid on and including 10mm thick rendering in cement mortar 1:3 backing coat complete all as specified and directed by Engr-in-charge. Make for Item No 12&13: NITCO/ SOMANY/ ASIAN / JOHNSON/KAJARIA/ORIENT BELL

M&L for Mild steel deformed TMT bars 10mm dia and above as in reinforcement to concrete cut to length bent to shape required including cranking bending and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as directed by Engr-in-charge.

M&L for Mild steel deformed TMT bars 8mm dia as in reinforcement to concrete cut to length bent to shape required including cranking bending and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as directed by Engr-in-charge.

M&Lfor Mild steel deformed TMT bars 5mm dia and over up to and including 10 mm dia as in stirrups, spacers and binders , cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with and including mild steel wire (annealed) not less than 0.9mm dia all as specified.

M&L for reinforced cement concrete 1:2:4 mix, type B1 (using 20 mm graded stone aggregate) as in foundations, including rafts, footings, foundation beams, plinth beams etc., all as specified and directed by Engineer-in-Charge. Note: Formwork and reinforcement shall be measured and paid seperately.

M&L for reinforced cement concrete 1:2:4 mix, type B1 (using 20 mm graded stone aggregate) as in columns, pillars, piers, posts and struts etc., all as specified and directed by Engineer-in-Charge. Note: Formwork and reinforcement shall be measured and paid seperately.

M&L for reinforced cement concrete 1:2:4 mix, type B1 (using 20 mm graded stone aggregate) as in beams, cantilevers, bressummers, lintels exceeding 1.5 m span, bands etc., all as specified and directed by Engineer-in-Charge. Note: Formwork and reinforcement shall be measured and paid seperately.

M&L for reinforced cement concrete 1:2:4 mix, type B1 (using 20 mm graded stone aggregate) as in slabs supported on walls, colums, beams, etc., complete all as specified and directed by Engineer-in-Charge. Note: Formwork and reinforcement shall be measured and paid seperately.

Use and removal of steel formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for rough finished surfaces of concrete flat all as specified and directed by Engineer-in-Charge.

Use and removal of steel formwork to sides of square, rectangular or polygonal pillars, posts, struts, piers, columns and stanchions for rough finished surfaces of concrete all as specified and directed by Engineer-in-Charge.

Use and removal of steel formwork to sides and soffits of floor or roof beams, bands, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc., for rough finished surfaces of concrete flat all as specified and directed by Engineer-in-Charge.

Use and removal of steel formwork to soffits of slabs etc., for rough finished surfaces of concrete flat all as specified and directed by Engineer-in-Charge.

S&F factory made PVC Solid Door frame of size 50mmx47mm made out of 5mm plain coloured PVC sheet reinforced with MS Square tube, fixed in opening as per specification and dawings.

S&F Factory made Solid panel PVC Door Shutter of 30mm thick (Style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colourr PVC 'C' channel having a PVC sheet strip 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail ; Panelling of plain clour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beeding and jointed together with solvent cement as per specification and drawing. Make for Item No. 25&26: - SINTEX / RAJSHRI PLASTIWOOD/ NANDI/ UNIVERSAL

S&F 100 mm size mild steel cold rolled medium weight butt hinges complete all as specified and directed.

S&F 150 mm long Aluminium alloy handles cast type anodised all as specified and directed.

S&F 200 mm long Aluminium anodised barrel tower bolts of extruded aluminium section all as specified and directed. Make for Item No. 27 to 29: - CROWN/ CLASSIC/ JYOTHI/ AMIT/ MOWJEE/ARGENT/Bharat/Alans/Hettich/Everlite or any ISI marked make as approved by GE.

S&F steel ventilators with top hung shutters (glazed or wire mesh shutters) fitted with box type hinges with suitable MS handles, peg stays complete all as directed by Engr-in-charge. Make: M/s Madhu industries / M/s.SEN Harvick / M/s. Shiv Mular / M/s. AGEW. / M/s. Multiwyn Industries Corpn/ M/s Ganesh rolling shutters/M/s Venkateswara rolling shutters or equvalent make as approved by GE.

S & F 3mm thick figured glass pin head type fixed with oil putty and necessary clips/nut bolts area not exceeding 0.5Sqm in each pane complete all as directed by Engr-in-Charge. Make:- TRIVENI/ SAINT GOBAIN/ MODIGUARD/ATUL/ HINDUSTAN or equivalent as approved by GE.

S&F PVC (SWR) pipes 110mm bore single socket in any length with rubber ring joints fixed to wall or laid in floors complete all as directed by Engr-in-Charge.

S&F PVC (SWR) pipes 75mm bore single socket in any length with rubber ring joints fixed to wall or laid in floors complete all as directed by Engr-in-Charge.

S&F PVC (SWR) bends (any radius) suitable for 75mm bore pipe fitted with access door complete all as directed by Engr-in-charge.

S&F PVC (SWR) bends (any radius) suitable for 110mm bore pipe fitted with access door complete all as directed by Engr-in-charge.

M&L PVC (SWR) P trap 125/110mm plain including jointing with solvent cement complete all as specified and directed by Engr-in-Charge.

M&L PVC (SWR) floor trap 75mm plain with grating including jointing with solvent cement complete all as specified and directed by Engr-in-Charge. Make for item No. 31 to 37: PRINCE/ SUDHAKAR/ NANDI/ FINOLEX/ SWASTIK/SUPRIME

M&L 75 mm thick PCC 1:3:6, type C2 (using 40mm graded stone aggregate) in plinth protection/path laid in alternative bays finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

S&F 15mm bore GI water tubing medium grade with all fittings and fixed to wall, floor, ceiling complete all as specified and as directed by Engr-in-charge. Make: TATA/JINDAL/ZENITH

S&F 15mm bore GI water tubing medium grade with all fittings laid in trenches complete all as specified and as directed by Engr-in-charge. Make: TATA/JINDAL/ZENITH

S&F bib taps 15 mm bore, cast copper alloy chromium plated screwed down high pressure, with crown or capstan head, screwed for iron pipe all as specified and directed by Engr-in-Charge. Make: SEIKO/RYBO/SPECTRUM/ NMC/L&K

S&F Stop/angle valves 15 mm bore, cast copper alloy chromium plated screwed down high pressure, with crown or capstan head, screwed both ends for iron pipe or for unions all as specified and directed by Engr-in-Charge. Make: SEIKO/RYBO/SPECTRUM/ NMC/L&K

S&F towel rail 600mm long of PTMT fixed with and including chromium plated brass scres and wooden/plastic cleats (Minimum weight 190gms) complete all as directed by Engr-in-Charge. Make: PRAYAG/POLYTUFF or equivalent as approved by GE.

S&F PVC connection pipe 15mm dia, 450mm long with PTMT check nuts and washer on both ends complete all as directed by Engr-in-Charge. Make:- PRAYAG/POLYTUFF or equivalent as approved by GE.

S&F Orrissa pattern vitreous china squatting pan white colour of size 580x440mm with integral footrest (Excluding flushing cistern and flush pipes) but including cement concrete bedding and P or S trap as required including PVC pipe upto finished floor level to connect flush pipe, complete all as directed by Engineer-in-Charge. Make: HINDWARE / NEYCER/ PARRYWARE / CERA

S&F Vitreous china wash down water closet pan (pedestal pattern) white, excluding flushing cistern and flush pipe but including Plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device, complete all as specified and directed Engr-in-Charge. Make: HINDWARE / NEYCER/ PARRYWARE / CERA

S&F PVC valveless, symphonic action type, flushing cistern 10ltr capacity, low level, white with inlet ball valve float and handle along with suitable flush pipe/bend including brackets complete all as directed by Engr-in-Charge. Make: PARRY WARE (SLIMLINE)/ COMMANDER/ HINDWARE

S&F Vitreous China wash basin, white, flat back, of size 550x400 mm, excluding taps, waste chain and plug and porcelain stopper but including brackets and 40mm dia brass chromium plated waste fitting and 40mm dia 90cm long PVC waste pipe, all as specified and directed by Engr-in-Charge. Make: HINDWARE / NEYCER/ PARRYWARE / CERA

S&F Pillar taps fancy type 15 mm bore, cast copper alloy, chromium plated with crown or capstan head screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks & fly-nuts, screwed for iron pipe, all as specified and directed by Engr-in-Charge. Make: SEIKO/RYBO/SPECTRUM/ NMC/L&K

S&F vitreous china bowl urinal flat back,half stall type, white with grating and union for discharge pipe incl providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement complete all as directed by Engr-in-charge. Make: HINDWARE / NEYCER/ PARRYWARE / CERA

M&L for salt glazed stone ware drain pipes of 150 mm bore grade 'A' laid in trenches and jointed in cement mortar 1:1 including complete all as directed by Engineer - in -Charge. Make:- INDO PIPES/ KIRAN POTTERIES/ MANCHERIAL CERAMICS/NOVODAYA CERAMICS or equivalent make as approved by GE

M&L for salt glazed stone ware bends of 150 mm bore grade 'A' laid in trenches and jointed in cement mortar 1:1 complete all as directed by Engineer - in -Charge.

M&L for plain cement concrete bed 1:4:8, type C2 (using 40 mm graded stone aggregate) to drain pipe 150 mm bore including packing under and hunching against the sides of pipes after they laid and tested complete all as directed by Engineer-in-Charge.

S&F Swivel shower of PTMT any colour for fixing with 15mm pipe. (Minimum weight 40gms) suitable to fix for 15mm dia iron pipe all as specified and directed by Engr-in-Charge. Make: PRAYAG/POLYTUFF or equivalent as approved by GE.

S&F 105x60 mm size pressed steel door frame for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., including PCC 1:3:6 type C0 filling complete all as directed by Engr-in-Charge. Make: - DIWAN STEELS/Ajanta Ispat/AVA Steels or equivalent as approved by GE.

S & F 30 mm thick Second class hard wood Glazed and skeleton shutters for doors, open rebated and prepared to receive glass,gauze etc. without sash bars, edges of framing plain, chamferred or rounded, fitted with cut and mitred beads for securing glass, wire gauge etc. ; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) fitted to chowkats all as specified and directed. Timber:- Sal/Kalasiris/Chaplash/Hollock/Bijasal

S & F galvanised mild steel wire cloth, 0.63 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or galvanised wire staples or wooden beeds all as specified and directed.

S&F mild steel 375mm, ordinary rat tail rod pattern springscluding roller and roller plate complete. all as specified and directed.

M&L Preparing new or previously un treated surfases of wood and wood based surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer all as specified and directed. Make: ASIAN/ SHALIMAR/ BERGER/ JENSON&NICHOLSON/IEL/NEROLAC/IEL

M&L for preparation of new or previously un treated surfaces of steel and iron surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and directed. Make: ASIAN/ SHALIMAR/ BERGER/ JENSON&NICHOLSON/IEL/NEROLAC/IEL

M&L for second class hard wood clean sawn scantling, framed and fixed complete all as specified and as directed by Engineer-in-Charge. WOOD: Sal/Kalasiris/Chaplash/Hollock/Bijasal

M&L preparing new wooden surfaces of any description over 10 cm width or girth and applying two coats of creosote oil complete all as specified and directed by Engineer-in-Charge.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet (trepezium or tile pattern etc.) 0.50 mm thick (with 0.45 mm BMT) of any colour having tensile strength of 550 Mpa (pitch of corrugation shall be 200mm to 250mm and crest shall be 28mm to 32mm) as in roof covering/ cladding to wall fixed with self tapping screws complete all as specified and as directed by Engineer-in-charge. Make: TATA BLUESLOPPE/ LLYODS /JMBS/EVEREST INDUSTRIES LTD/CRIL or equivalent as approved by GE.

M&L for 100 mm thick Plain Cement Concrete 1:4:8, type D2 (using 40mm graded stone aggregate) as in sub base and finishing even and rough to receive toping layer complete all as specified and directed by Engineer-in-charge.

M&L for preparation of new plastered surfaces of walls and applying two coats of distemper oil emulsion over one coat of alkali resistant primer complete all as specified and as directed by Engineer-in-Charge. Make: ASIAN/SHALIMAR/BERGER/ JENSON & NICHOLSON

S&F GI frame work of size 605 x 605 mm, for seamless celing comprising of GI perimeter chanel 0.55mm thick with two unequal flanges of 20 and 30 mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/ intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre including 6mm dia GI hangers (upto1200mm length) adjusting level and providing 4 mm thick E Board (Everest) noncombustible moisture resistant plain building boards, fixed to GI frame work with screws as in ceiling and applying 3 coats of white wash complete all as specified and as directed by Engineer-in-charge.

M&L for Machine cut kota stone slab flooring 20-25mm thick as in floors laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing laid on and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed by Engr-in-charge.

M&L for Machine cut kota stone slab flooring 20-25mm thick as in skirting, dado or clading laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing laid on and including 10mm thickrendering in cement mortar 1:4 complete all as specified and directed by Engr-in-charge.

S&F 300mm long aluminium alloy anodised sliding door bolts with hasp & staple (bolt type) and fixing clip of sheet , cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy all as specified and directed. Make: - CROWN/ CLASSIC/ JYOTHI/ AMIT/ MOWJEE/ARGENT/Bharat/Alans/Hettich/Everlite or any ISI marked make as approved by GE.

S&F 40mm thick factory made flush shutters, solid core construction with block board core and plywood face panels, both faces are covered with decorative face vener with lipping/ frame to match complete all as specified and directed by Engineer-in-Charge. Make: - Green Ply/Archid Ply or equivalent as approved by GE.

S&F steel window with side hung shutters (glazed or wire mesh shutters) fitted with box type hinges with suitable MS handles, peg stays, with glazing bars complete all as specified and directed by Engr-in-charge. Make: M/s Madhu industries / M/s.SEN Harvick / M/s. Shiv Mular / M/s. AGEW. / M/s. Multiwyn Industries Corpn/ M/s Ganesh rolling shutters/AVA steels/Ajanta Ispat or equvalent make as approved by GE.

S & F 3 mm thick Sheet Glass, ordinary quality and glazing with oil putty in steel windows or fitted with wooden beadings in square n. exe 0.5 sqm each pane all as specified and directed. Make: TRIVENI /VALLBH/ATUL/ HINDUSTAN / PILKINGTON / MODIGUARD/SAINTGOBAIN

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc., laid bedded and pointedin any mortar and removing rubbish off the premises complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick square/rectangular area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, on vertical surfaces such as skirting/dado, jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles laid on and including 10mm thick rendering in cement mortar 1:4 backing coat complete all as specified and directed by Engr-in-charge. Make: NITCO/ SOMANY/ ASIAN / JOHNSON/KAJARIA/ORIENT BELL

M&L for cement concrete chequered tiles 250 x 250 x 22 mm thick with grey cement and pigment, set and jointed in neat cement slurry and pointed in grey cement to match the surfaces as in floors laid over and including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed. Make: NITCO/DECO/BHARAT or equivalent as approved by GE.

M&L for 75 mm thick Plain Cement Concrete 1:3:6, type C2 (using 40mm graded stone aggregate) as in sub base and finishing even and rough to receive toping layer including demolition of existing concrete and removing rubbish off the premises complete all as directed by Engr-in-charge.

M&L for factory made precast cement block masonry with solid blocks made of Plain cement concrete 1:3:6 mix type C1 (using 20 mm graded stone aggregate) exceeding 10cm width and setting in cement mortar 1:6 including demolition of existing block masonry complete all as specified and directed by Engineer-in-charge. Make : Shankar Saw Mills/Sangam Prefeb Products or equivalent make as approved by GE.

M&L for rendering 15 mm thick on brickwork or concrete surfaces in cement mortar 1:4 finished fair and even including taking down existing plaster and removing rubbish off the premises complete all as specified and directed by Engr-in-charge.

M&L for 75 mm thick Plain Cement Concrete 1:3:6, type C2 (using 40mm graded stone aggregate) as in sub base and finishing even and rough to receive toping layer complete all as directed by Engr-in-charge.

M&L for walling of random rubble masonry, uncoursed, well bonded, bedded and solidly hearted built in cement mortar 1:6 including necessary hammer dressing to face stones and dressing of face beds and joints complete all as specified and directed by Engineer-in-charge.

M&L for rendering 15 mm thick on stone masonry surfaces in cement mortar 1:4 finished fair and even complete all as specified and directed by Engr-in-charge.

Excavation in post holes (for similar holes) each n.exc 0.5cum, getting out, in soft/loose soil and removing surplus soil upto 50m complete all as specified and directed by Engineer-in-Charge.

M&L for plain cement concrete 1:3:6 mix, type C2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed by Engineer-in-Charge.

S&F Fe-290 Gde E-165 mild steel angle or other sections as in posts and struts in fencing etc., and similar work including cutting tops to shape as directed,drilling holes, notching for wire, including all necessary drilling holes for bolting or riveting, etc., complete all as specified and directed by Engineer-in-charge.

S&F MS galvanised chain link fencing fixed to any type of standards, rails, posts, straining bolts etc., including provision of binding wire including dismantling of old fencing wire mesh any type complete all as specified and directed by Engineer-in-charge.

S&F for galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacing and straining and fixing to any type of standard rails straining bolts, incl securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc., including dismantling old rusted barbed wire any type all as specified and directed.

S&F mild steel machine made screw bolts not exceeding 5cm long 11 to 15 mm (diameter of neck) with hexagonal or square heads at one end and screwed the other, screwed end fitted with washers and one hexagonal or square nut, not exceeding 5 cm long all as specified and directed.

M&L for preparation of new or previously un treated surfaces of steel and iron surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of black Japan paint all as specified and directed. Make: ASIAN/ SHALIMAR/ BERGER/ JENSON&NICHOLSON/IEL/NEROLAC/IEL

M&L for preparation of new or previously un treated surfaces of steel and iron surfaces of any description, not exceeding 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over one coat of red oxide primer all as specified and directed. Make: ASIAN/ SHALIMAR/ BERGER/ JENSON&NICHOLSON/IEL/NEROLAC/IEL

S&F Mild steel bar round bars 6 to 8 mm dia in fencing, cut to length, bent to shape required including cranking, bending, hooking ends and binding etc. conforming to grade I, IS-432 (Part I) all as specified and directed.

S&F Fe-290 Gde E-165 Rolled mild steel sections as in framed work for doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, doors etc. to be prepared for hanging or sliding with & including either hooks & hinges or steel hanging door fittings & hanging; also fastening & fixing complete all as specified and directed by Engineer-in-charge.

M&L for construction of Valve chamber of internal dimension/size 750 x 750 x 750 mm, with 200mm thick pre-cast PCC solid block masonry (made of PCC 1:3:6 type C-1 : using 20mm graded crushed stone aggregate) wall in cement mortar 1:6, with 1.6 mm thick MS sheet cover, fixed with 25x25x6 mm stiffner welded around, welded over angle iron frame of size 65 x 65 x 6 mm with locking arrangements including applying two coats of first grade synthetic enamel paint (of approved tint) over a coat of red oxide primer on steel surfaces, necessary earth work in soft/loose soil with and including 100 mm thick PCC (1:3:6) Type C-2 (using 40mm graded stone aggregete) as in foundation, 50 mm thick PCC (1:2:4),Type B-1 (using 20mm graded stone agregate) as in coping on top including rendering 10mm thick in cement mortar 1:6, finished even and fair and applying three coats of white wash on exposed surfaces, complete all as specified and directed by the Engineer-in-Charge. (The chamber shall be 150 mm above the ground level.)

S&F gun-metal, globe or gate valves of with iron wheel head, screwed both ends for iron pipe of 25 mm dia bore and fixed complete all as specified and directed by the Engineer-in-Charge.

All as per item No. 94 above but 20 mm dia bore. Make for Item No. 94&95:LEADER/NETA/ANCHOR/NMC/ DURGA/ZOLOTO or equivalent ISI marked make as approved by GE.

Supply and fixing Rotational moulded polyethylene water storage tank cylindrical vertical double layered, 1000 ltrs capacity with closed top hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed by Engineer-in-Charge. Make: SINTEX/ INFRA/ GP/ ROTEX/ ORIPLAST/ ASHISH/ POLYCON or equivalent ISI marked make as approved by GE.

S&F Symet ball valve 20 mm with high pressure of PTMT with epoxy coated aluminum rod & high density plastic ball screwed for iron pipe and fixed min weight for 20 mm 210 gms, including taking down existing unserviceable ball valve complete all as specified and directed by Engineer-in-Charge. Make:- PRAYAG/POLYTUFF or equivalent as approved by GE.

S&F 25 mm dia bore medium grade galvanised iron tubing with all fittings and fixtures complete laid in trenches or on ground complete all as specified and as directed by Engineer-in-Charge. NOTE: Excavation and earth work shall be measured and paid separately.

All as per item No. 98 above but 20 mm dia bore. Make for Item No. 98&99: TATA/ ZENITH / JINDAL

Cutting the existing steel pipe line of size 25 mm dia and taking the connection to proposed 25mm dia pipe including required accessories (such as insert, tee, reducer, socket and all other accessories) required as per site condition complete all as directed by Engr in charge.

Supply and spreading of dry sand in trenches for cable coushioning and punned down complete all as specified and directed by Engineer-in-Charge. Note:- Punned thickness only shall be measured for payment purpose.

M&L for common burnt bricks, sub class 'B', of size 250 x 125 x 75 mm laid in trenches for cable protection including taking out existing bricks complete all as specified and directed by Engineer-in-charge.

Supply and laying in trenches, fixed to wall or drawn through pipe etc., XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 sqmm 2 core and connecting with necessary lugs complete all as specified and directed by Engineer-in-Charge. Note:- Excavation, earth work, brick protection, protection pipe and sand coushioning shall be measured and paid separately. Make of cable shall be CCI / Gloster / ICC / Unistar / NICCO / Asian (RPG) / Havells / Polycab/PRG/Universal/Plaza/Crystal cables/Terracom/ Rallison/Mescab/Jeypore/KEI

Material and labour for 25 mm dia bore GI tubing Light grade, laid under roads/ floor, or fixed to wall or along the pole with suitable size M.S.flat iron clamps, nuts, bolts and washers for cable protection complete all as specified and directed by Egineer-in-Charge. Make: TATA/JINDAL/ZENITH

M&L for point wiring with 1.5 Sqmm (nominal area) PVC insulated un - sheathed single core stranded copper conductor FRLS cable 1100 volts grade (conforming to IS) drawn through and including rigid non metallic PVC conduit, medium grade of suitable size with all necessary fittings, concealed in walls/ceilings etc., including 1.5 Sq mm PVC insulated copper conductor FRLS cable for earth continuity conductor and connected to earth dolly and to be terminated in 1.6 mm thick pressed steel terminal boxes concealed type/surface type for mounting fittings like switch, socket, fan regulator etc. with 3 mm thick laminated bakelite sheet cover (Make: Hylem or equivalent ) for housing switches, socket outlet, regulator etc., for one light /fan point controlled by one switch/one bell / buzzer point controlled by one bell push/one 3 / 5 -pin switch socket outlet 5 amps on independent board including testing on completion complete all as specified and directed by Engineer-in-Charge.

M&L for point wiring with 2.5 Sqmm (nominal area) PVC insulated un - sheathed single core stranded copper conductor FRLS cable 1100 volts grade (conforming to IS) drawn through and including rigid non metallic PVC conduit, medium grade of suitable size with all necessary fittings, concealed in walls/ceilings etc., including 2.5 Sqmm PVC insulated copper conductor FRLS cable for earth continuity conductor and connected to earth dolly and to be terminated in 1.6 mm thick pressed steel terminal boxes concealed type/surface type for mounting fittings like switch, socket, fan regulator etc. with 3 mm thick laminated bakelite sheet cover (Make: Hylem or equivalent ) for housing switches, socket outlet, regulator etc., for one 5 / 6 -pin switch socket outlet 15 amps on independent board including testing on completion complete all as specified and directed by Engineer-in-Charge. Make for Item No. 105&106 Cable: (i) Finolex, (ii) Plaza, (iii) Havells, (iv) Polycab, (v) KEI, (vi) Anchor Conduit: (i) Kinjal, (ii) Alwyn (iii) Harsh, (iv) Finolex (v) Berlia (vi) Plaza

S&F switch piano, flush button, single pole, 5 amps, one way complete all as specified and as directed by Engineer-in-Charge.

S&F switch socket combination 2 – in – one 5 Pin , 5 amps flush type complete all as specified and as directed by Engineer-in-Charge.

S&F switch socket combination 2 – in – one 6 Pin , 5 / 15 amps flush type complete all as specified and as directed by Engineer-in-Charge.

S&F lamp holder, PVC/Polycarbonate insulated body with back plate including 10 W retto fit LED lamp for batten fittings complete all as specified and as directed by Engineer-in-Charge.

S&F ceiling rose 3 terminal PVC/Polycarbonate, insulated body complete all as specified and as directed by Engineer-in-Charge. Make for Item No. 107 to 111: (i) Anchor (ii) Plaza, (iii) Havells (Crabtree) (iv) ABB (v) Shalabh

S&F Energy efficient LED Tube light fitting, 1x18/20 watt, with LED tube rod 18/20 Watt with bipin holders, connector block etc., complete with all accessories internally prewired and including connecting up with three core pvc sheathed flexible copper conductor cable of size 1 sqmm complete all as specified and as directed by Engineer-in-Charge. Make: Cat part DMLN1LT8-16 of Fitting and LTT8-20 of rod of Crompton or HSN Code:8539 & MAS18W865 T8I-2100lm(PC body),20W865 T8INDI-2100 lm(rod) of Philips or Cat No. SUB118T8 LED(Body),SLETL-DSPC REFORM of Surya or LUMELINEBS 18WLED830SPCWH of Havells.

Supply and fixing Exhaust Fan AC Single Phase, 230/240 Volts, of size 300 mm sweep, Heavy duty, with & including louvers, mounting ring, MS rag bolts, nuts, washers etc and connected from ceiling rose/connector with & including suitable size flexible copper conductor PVC insulated sheathed cord, and testing on completion complete all as specified and as directed by the Engineer-in-Charge. Make: CG Model BRISK AIR or equivalent in Polar/ Havells/ Khaitan/Usha/Orient

Supply and fixing integrated LED bulk head luminaries comprises of pressure die cast housing with clear acrylic diffuser & frame and IP 65 protection including 10 W LED bulb and connecting up with existing cable complete all as specified and as directed by Engineer-in-Charge. MAKE: Cat part No. LBHE-10-CDL of Crompton or Philips Cat no. WT 202W LED 6S NW PSU S2 PC or equivalent in Havells/Bajaj.

S&F sheet metal enclosure DB SPN 8 way 240 V with 200 Amp rated bus bar, powder coated, double door all as specified and as directed by Engineer-in-Charge.

S&F sheet metal enclosure DB SPN 4 way 240 V with 200 Amp rated bus bar, powder coated, double door all as specified and as directed by Engineer-in-Charge.

Supply and Fixing of MCB SPN 6 to 32 Amps, 10 KA breaking capacity, 240 volts, 50 Hz complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing of MCB SP 6 to 32 Amps, 10 KA breaking capacity, 240 volts, 50 Hz complete all as specified and as directed by Engineer-in-Charge. Make for Item No. 115 to 118: Legrand/Siemens/Schneider

Earthing complete with galvanized steel earth plate electrode 600 x 600 x 6 mm buried directly in ground ( earth pit not less than 2.25 m deep bellow ground level ) with top edge of the plate not less than 1.5 m below normal ground level, connected to GI earth lead wire 4 mm dia. by means of galvanized iron or steel bolts , nuts , check nuts and washers, and connected to equipments as directed , including funnel with GI medium grade watering pipe 20 mm bore , wire mesh , charcoal or coke and common salt in alternate layers of 15 cm compacted thickness all around the earth electrode , with concrete pit in PCC 1:3:6 type C-1 , 50 mm thick pre cast RCC 1 : 2 : 4 type B-1 cover slab reinforced with 8 mm dia deformed bar 15 cm C/C and suitable handle of 10 mm dia round bar, 15 mm GI medium grade pipe for earth lead protection including necessary excavation earth work in soft/loose soil and disposal of spoil to a distance n.exc. 50 m and necessary testing complete all as shown on electrical plate No. 3 of MES SSR Part-I including taking out existing earth plate etc., complete all as specified and as directed by Engineer-in-Charge. NOTE: Rate quoted shall be deemed to include for earth lead and protection pipe upto 7.5m.

M&L for point wiring with 1.5 Sqmm (nominal area) PVC insulated un - sheathed single core stranded copper conductor FRLS cable 1100 volts grade (conforming to IS) drawn through and including rigid non metallic PVC casing and capping, medium grade of suitable size with all necessary fittings, fixed on walls/ceilings etc., including 1.5 Sq mm PVC insulated copper conductor FRLS cable for earth continuity conductor and connected to earth dolly and to be terminated in 1.6 mm thick pressed steel terminal boxes concealed type/surface type for mounting fittings like switch, socket, fan regulator etc. with 3 mm thick laminated bakelite sheet cover (Make: Hylem or equivalent ) for housing switches, socket outlet, regulator etc., for one light /fan point controlled by one switch/one bell / buzzer point controlled by one bell push/one 3 / 5 -pin switch socket outlet 5 amps on independent board including testing on completion complete all as specified and directed by Engineer-in-Charge.

M&L for point wiring with 2.5 Sqmm (nominal area) PVC insulated un - sheathed single core stranded copper conductor FRLS cable 1100 volts grade (conforming to IS) drawn through and including rigid non metallic PVC casing and capping, medium grade of suitable size with all necessary fittings, fixed on walls/ceilings etc., including 2.5 Sqmm PVC insulated copper conductor FRLS cable for earth continuity conductor and connected to earth dolly and to be terminated in 1.6 mm thick pressed steel terminal boxes concealed type/surface type for mounting fittings like switch, socket, fan regulator etc. with 3 mm thick laminated bakelite sheet cover (Make: Hylem or equivalent ) for housing switches, socket outlet, regulator etc., for one 5 / 6 -pin switch socket outlet 15 amps on independent board including testing on completion complete all as specified and directed by Engineer-in-Charge. Make for Item No. 120&121 Cable: (i) Finolex, (ii) Plaza, (iii) Havells, (iv) Polycab, (v) KEI, (vi) Anchor Casing&Caping: (i) Kinjal, (ii) Alwyn (iii) Harsh, (iv) Finolex (v) Berlia (vi) Plaza

M&L for sub main wiring complete with 2 runs of 4 Sqmm PVC insulated heavy duty and unsheathed cable with multistranded copper conductor and drawing through and including rigid PVC casing caping of 25 dia fixed on wall/ceiling and connecting terminal ends including provision of 1 run of 4 Sqmm insulated multistranded copper cable as earth continuity conductor and connecting to earth dolly complete all as directed by Engr-in-charge. Note: 2 runs of 4 Sqmm and one run of 4 Sqmm and one run of casing & Caping shall be measured as one unit length. Make Cable: (i) Finolex, (ii) Plaza, (iii) Havells, (iv) Polycab, (v) KEI, (vi) Anchor Casing & Caping: (i) Kinjal, (ii) Alwyn (iii) Harsh, (iv) Finolex (v) Berlia (vi) Plaza

M&L for point wiring with 1.5 Sqmm (nominal area) PVC insulated un - sheathed single core stranded copper conductor FRLS cable 1100 volts grade (conforming to IS) drawn through and including stove enamelled steel conduit of suitable size with all necessary fittings, concealed in walls/ceilings etc., including 1.5 Sq mm PVC insulated copper conductor FRLS cable for earth continuity conductor and connected to earth dolly and to be terminated in 1.6 mm thick pressed steel terminal boxes concealed type/surface type for mounting fittings like switch, socket, fan regulator etc. with 3 mm thick laminated bakelite sheet cover (Make: Hylem or equivalent ) for housing switches, socket outlet, regulator etc., for one light /fan point controlled by one switch/one bell / buzzer point controlled by one bell push/one 3 / 5 -pin switch socket outlet 5 amps on independent board including testing on completion complete all as specified and directed by Engineer-in-Charge.

All as per item No. 123 above but for One 3/5 pin switch socket outlet 5 amps on same board along with other switches complete all as specified and directed by Engineer-in-Charge. Make for Item No. 123&124 Cable: (i) Finolex, (ii) Plaza, (iii) Havells, (iv) Polycab, (v) KEI, (vi) Anchor

S&F Energy efficient LED Tube light fitting, 1x16/20 watt, CMRI certified Flameproof light fitting with tube light fixture, System lumins efficacy not less than 65lm/W, Housing Die cast aluminium, IP65 protection, Dimensions 1325x220x140mm with all accessories internally prewired and including connecting up with three core 0.50 sqmm FLSH copper conductor PVC sheathed cable complete all as specified and as directed by Engineer-in-Charge. Make:Crompton model "FIAMMA-II and Cat Part No. EXTN1LT8-16/20" or equivalent in Sudhir.

S&F sheet metal enclosure DB SPN 2 way 240 V with 100 Amp rated bus bar, powder coated, double door all as specified and as directed by Engineer-in-Charge. Make: Legrand/Siemens/Schneider

SANJAY SAW MILL

GARGO TRADERS

DEEP CHANDRA JOSHI

JAYSHREE CONCERN

RAMESH GURUNG

MS BRAHMA CONSTRUCTION

SANJAY MITTAL