REPAIR OF FALSE CEILING AND ROOFS AT JAK LI RTC DHANSAL UNDER GE ARMY DHAR ROAD

Amount

Dismantling of existing water proofing treatment (unreinforced cement concrete polymeric water proofing membrane and cement mortar) not exceeding 15 cm thickness above the ground level complete all as specified and directed.

25mm thick plain cement concrete 1:2:4 type B1 using 20mm graded stone aggregate and finishing the surface even and smooth as in padding concrete/roof slab including mixing of Water proofing compound complete all as specified and directed.

Rendering 10mm thick on fair faces of brick work or concrete surfaces finished even and fair on walls in cement mortar(1:4) , using water proofing compound complete all as specified and directed. (Note : WPC will be measured and paid for separately)

Supply only integral water proofing compound, ISI marked, complete all as specified and directed.

M & L for applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per square metre including cleaning surfaces complete all as specified and directed.

M & L for fixing APP based polymeric membrane minimum weighing not less than 3kg/sqm and minimum 3mm thick reinforced with polyester non-woven fabric (weight not less than 150 gm/Sqm) laid on primed surface of roofs using butane torch, and sealing all joints after and including applying bituminous primer @ 0.40 litre per square metre over clean RCC roof surfaces, complete all as specified and directed.

Disconnecting existing tanks exc 250 and not exc 500 ltrs, including cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes etc and setting aside (or lowering if required) for repairs, cleaning etc., and hoisting if required reconnecting and refixing in position complete all as specified and directed.

Disconnecting existing tanks exc 500 and not exc 1000 ltrs, including cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes etc and setting aside (or lowering if required) for repairs, cleaning etc., and hoisting if required reconnecting and refixing in position complete all as specified and directed.

Taking up or down steel tubing and connections, 15 mm bore fixed on walls, floors or ceiling etc including cleaning for refixing or removal complete all as specified and directed.

Taking up or down steel tubing and connections, 20 mm bore fixed on walls, floors or ceiling etc including cleaning for refixing or removal complete all as specified and directed.

S&F 15mm bore tubes, medium grade, galvanised with and including all fittings fixed to walls, floors, or ceiling or laid in floors etc complete all as specified and directed.

S&F 20mm bore tubes, medium grade, galvanised with and including all fittings fixed to walls, floors, or ceiling or laid in floors etc complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not other wise provided for.

Dismantling of plain & corrugated steel sheeting any gauge, thickness including Nanital or similar pattern roof covering like ridges, hips, valleys and flashings etc complete all as specified.

Rolled mild steel work in tubular trusses including special shaped washer etc. complete using ERW or incl butt welded tubes conforming to IS 1161-1998 grade St-240 and painted one shop coat of zinc chromate promer paint (incl preparation of surface) at contractor's workshop before fabrication complete all as specifed and directed.

Mild steel rolled section as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastening and heavy bracket framing (Beam, tee, angle, channel or flat sections) incl distance pieces, cleats etc. confirming to grade Fe-290. Gde- E-165. complete all as specifed and directed.

S&F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour tensile strength of 550mpa as in roof covering/cladding to wall, fixed with self tapping screws as a specified.

S&F pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550mpa as in roof covering/cladding to wall, fixed with self tapping screws as a specified.

Demolition of brickwork or stone boulder masonary built in cement mortar including all quoins, arches, pillars etc complete all as specified.

Brickwork with sub class ‘B’ (old size) bricks, straight or curved on plan exceeding 6 metre mean radius built in cement sand mortar 1:6 complete all as specified.

Brickwork with sub class ‘B’ (except bricks) bricks, straight or curved on plan exceeding 6 metre mean radius built in cement sand mortar 1:6 complete all as specified.

Taking down cement plaster of any description including raking out joints, hacking for key, scrubbing down with water etc all as specified.

Rendering 15 mm thick in cement and sand mortar 1:4 on fair faces of brick work or cement concrete surfaces with using integral waterproofing compound including finishing the surface even and smooth without using extra cement complete all as specified. (supply only of W P C shall be measured and paid separately).

Rendering 10 mm thick in cement and sand mortar 1:6 on other than fair faces of brick work or cement concrete surfaces including finishing the surface even and smooth without using extra cement complete all as specified and as directed

Rendering 5 mm thick in cement and sand mortar 1:4 on concrete surfaces of ceiling including finishing the surface even and smooth without using extra cement complete all as specified and as directed.

Preparation of newly plastered surfaces of walls and applying two coats of cement base paint complete all as specified.

Preparation of newly plastered surfaces of ceiling and applying two coats of white wash complete all as specified.

Preparation of newly plastered surfaces of walls and applying two coats of distemper oil emulsion complete all as specified.

M & L for preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a priming coat of red oxide zinc chrome primer complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, gypsum, POP, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and directed.

Providing and fixing of designer ceiling board of size 600 x 600x4mm thick pre-painted ceiling board tiles of approved texture at all height laid on hot dipped galvanised iron imposed grid system with 24mm wide T-section exposed flanges which shall be powder coated white. The frame work shall comprise of main runner made from 0.33mm thick GS sheet and of size 24x32x3000mm and spaced at 1200mm centres securely fixed to the structural soffits by approved hangers at 1200mm maxiumum centres. Hangers of GI wire 4mm dia to be fixed by approved rawl plug, level and justers and screws etc. The last hanger at the end of feach main runner shall not be greater than 450mm from adjacent wall. Flush fitting of 1200 mm long cross tee (with double stitching) to be interlocked between main renders at 600mm to be supoorted independently. 600x600mm modules to be formed by fitting 600mm long cross tee centrally between the 1200mm cross tee. Tee, Permimeter wall angle shall be of 0.45mm thick GS sheet, complete all as specified and directed. (Make : Saint Gobain, Everest)

S&F 5mm thick PVC Sheet fillet of width 35mm for wall panelling inclusive of fixing on to wall to make PVC frame as per specification and drawing complete all as specified and directed.

S&F Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications complete all as specified and directed.

Demolition of cement concrete ( reinforced) other than ground floors, beams stair cases, landings, chajjas and similar suspended work not exc. 15 cm thick (reinforcement cut as required to facilitate demolition) complete, all as specified.

Use and waste form work to sides and soffits of floor or roof beams, beams haunching, girders, bressummers, lintels, cantilevers, shelves including supports, over hangs, etc. also splays between floors and beams etc for flat rough finished surfaces of concrete complete all as specified and directed.

Use of formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete walls, floor and roofs not exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10 cm but not exc 20 cm wide for rough finished surfaces of concrete complete all as specified and directed

M & L mild steel TMT bars 10mm dia and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M & L mild steel TMT bars 6 mm to 8 mm dia and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M & L for providing RCC 1 : 2 : 4 Type B1 (20 mm graded aggregate) for slabs supported on walls, beams and column in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed

M/S SANJAY STEEL WORKS

MandeepConstructionCo

NARESH KUMAR KHAJURIA

MAHADEV ENTERPRISES

devraj chalotra