SPECIAL REPAIR TO BLDG NO P 50 AND P 51 SINGLE JCOs ACCN AND CERTAIN REV AND MINOR WORK AND DEMOLITION OF BLDG NO T 07 TO T 11 T 15 AND T 16 AT AKHNOOR UNDER GE NORTH AKHNOOR

Amount

Demolition of brickwork or stone boulder masonary built in cement mortar including all quoins, arches, pillars etc complete all as specified and as directed by Engineer -in-Charge

Demolition of cement concrete (un-reinforced) in ground floors and paving not exceeding 15 cm thickness (below or above ground level ) complete all as specified.

Taking down old unserviceable flushing cistern of any description complete all as specified.

Taking down old unserviceable bath fitting i.e. Bibcock/stop cook/Angle valve etc complete all as specified.

Dismantlling asbestos cement sheets in roof covering including ridges complete as as specified.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) not exc 1.5 Sqm each complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames)exc 1.5 sqm not exc 4.0 Sqm each complete all as specified and directed.

Dismantling mild steel work of any description complete all as specified and directed.

Dismantling water tank of capacity exceeding 500 litres but not exceeding 1000 ltrs and removing to stores, all as specified .

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in any type of soil as directed by Engineer-in-Charge.

Excavation in post holes (or similar holes ) each n. exc 0.5 Cum, getting out, returning, filling in and ramming earth or broken rubble mixed with erath around in layer n.exc 25cm, watering and removing surplus soil to a distance n. exc 50M and making good surfaces in any type of soil complete all as specified.

Plain cement concrete type B-0 1:2:4 (Using 20mm graded crushed stone aggregate) as in bed block plinth courses, apex stones etc complete all as specified.

Structural steel work as in roof trusses (framed) trussed purlins, crane gratries rails and fastening and heavy brackets (Beam, tee, angle or channel section) including distance pieces cleats all as specified.

Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

Ditto all as per item No. 14 here in before but plain.

100mm thick plain cement concrete type D-2 1:4:8 (Using 40mm graded aggregate) as in sub-base of floors path/hardstandings etc finished even and rough to receive topping layer complete all as specified.

100mm thick plain cement concrete type B-2 1:2:4 (Using 40mm graded aggregate) as in sub-base of floors paving & hardstandings etc laid in alternate pannel finished even and smooth without using extra cement complete all as specified.

Taking down cement plaster of any description including raking out joints, hackisng for key, scrubbing down with water etc all as specified and as directed by Engineer -in-Charge.

Rendering 10 mm thick in cement and sand mortar 1:6 on fair faces of brick work or cement concrete surfaces including finishing the surface even and smooth without using extra cement complete all as specified.

Rendering 15mm thick in cement mortar 1:4 finished fair and even without using extra cement complete all as specified and as directed.

Rendering 5 mm thick in cement and sand mortar 1:4 on concrete surfaces of ceiling including finishing the surface even and smooth without using extra cement complete all as specified and as directed.

Complete removal of existing treatment on walls all as specified.

Applying 1mm thick wall care putty of JK/Birla white all as specified and as directed.

Preparation of newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified and as directed.

Preparation of newly plastered surfaces of walls and applying two coats of cement base paint complete all as specified and as directed.

Preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer complete all as specified and as directed.

Preparation of old painted surfaces by washing, rubbing down and stopping of distempered and painted walls and applying one coats of oil bound distemper complete all as specified and as directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust , etc all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing rubbish off premises complete all as specified

Fixing 20mm dia PVC nozzles and injection grouting using Dr Fix IT URP 301 of M/s Pidilite Industries or equivlent as in sunken floor/ceiling all as specified and directed.

Applying two coats of Dr Fix IT fast flex 113 of M/s Pidilite Industries or equivlent.

25 mm thick PCC 1:2:4 type B-1, using 20 mm graded stone aggregate, including finishing surface of concrete topping even and rough as in screed bed complete all as specified.

Non skid ceramic tiles 7 to 8mm thick (Square/ reactangular) area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set and jounted neat cement slurry and pointed in white or coloured cement to match Screed bed or bedding layer of mortar 15 mm thick for laying floor finishes in CM 1:6 complete all as specified.

Non skid coloured ceramic joint free tiles 7 to 8mm thick (Square/rectangular) area of each tiles exc 0.06 Sqm but n.exc 0.11 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over the layer of screed bed 15 mm thick CM 1:6 complete all as specified.

Glazed ceramic tile 350 x 250 x 7mm/450x350x7mm thick (coloured) on vertical surfaces such as skirting, dados etc set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles over and including 10 mm thick screed bed in cement and sand mortar 1:4 complete all as specified.

20 mm thick makrana white marble as in border/cooking platform etc, bedded and jointed in cement mortar 1:6 of 20mm thick including pointing in white cement 1:2 using marble dust including cutting and polishing complete all as specified.

Vitreous china wash down water closet pan (pedestal pattern), white ( excluding flushing cistern and pipe) complete fixed in repair, all as specified and as directed.

PVC low level flushing cistern, valveless, syphonic action type, 10 litres capacity with inlet, ball valve float and handle with and including brackets & PVC bend pipe 90 cm long etc, supplied and fixed in repairs, complete all as specified.

Vitreous china wash basin, white, flat back, size 550x400mm including pillar tap, waste fitting chromium plated brass, chromium plated steel chain and rubber plug, porcelain stopper, a pair of CI brackets, waste pipe and pillar tap etc., fixed in repairs complete all as specified.

Tubular towel rail aluminium anodised 20 mm dia, D-type 60 cm long between flanges, including brackets and fixed to walls, complete all as specified.

PVC connection 15 mm size, of length 450 mm, with PTMT nuts supplied and fixed in repairs complete all as specified and as directed by Engineer-in-Charge.

Stainless steel gratings 100mm bore size fixed with cement motar.

Taking up or down steel tubing and connections, 15 mm bore fixed on walls, floors or ceiling etc complete all as specified.

Ditto- all as per item No. 44 here- in- before but 20 mm bore.

15mm bore tubes, medium grade, galvanised with and including all fittings fixed to walls, floors, or ceiling or laid in floors etc complete all as specified.

Ditto- all as per item No.46 here in before but 20mm bore.

Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for unions, for bore dia of pipe 15 mm, supplied and fixed in repairs complete all as specified.

Ditto- all as per item No. 48 here- in- before but 20 mm bore.

Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule, for bore dia of pipe 15mm, supplied and fixed in repairs complete all as specified.

Pillar taps cast copper alloy, fancy type with capstan head, CP, screwed down high pressure with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nut, screwed for iron pipe 15 mm bore, supplied and fixed in repairs, complete all as specified.

Ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe 20 mm dia (minimum weight 210 gms) complete all as specified.

Rotational moulded polyethylene water storage tanks of 1000 Litres capacity, (cylindrical vertical tanks with closed top) hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe etc including taking down existing tank complete all as specified.

Refixing the shutters area exceeding 1.00 sqm and n.exc 2.00 Sqm each in the same opening complete all as specified.

Hacking out old broken glass (any thickness, size, quality or description) from metal frames including punching or drilling out old glazing pins/spring clips and providing and fixing new ones glazed with oil putty fixed with beads complete all as specified.

03 mm thick sheet glass, ordinary quality and glazing with oil putty/wooden beads in square not exceeding 0.5 square metre in each pane complete all as specified.

Preparation of old painted surfaces by washing, rubbing down and stopping of distempered and painted walls and applying one coats of cement base paint complete all as specified and as directed.

Preparation of old painted steel surfaces of any description exc 10 cm width or girth, and applying one coats of synthetic enamel paint complete all as specified and directed.

Preparation of old painted wooden surfaces of any description exc 10 cm width or girth, and applying one coats of synthetic enamel paint complete all as specified and directed.

Preparation of old treated surfaces of walls (plastered or unplastered) and applying two coats of Apex emulsion paint with primer as in roof projection/chajjas incld removal of existing treatment complete all as specified and directed.

Preparation of old plastered surfaces of ceiling and applying two coats of white wash complete all as specified and as directed.

Precast cement concrete 1:2:4 (nominal mix), type B-1 using 20mm graded crushed stone aggregate as in landings, cover slabs (for manhole etc.), and similar articals with plain faces, set in cement mortar 1:4 complete all as specified & directed.

TMT bars 6 to 8mm dia, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, conforming to grade Fe-500, complete all as specified & directed.

Taking down carefully, copper / aluminium conductor unserviceable / perished point wiring (any type) for light/ fan/ light socket or power socket etc complete with fittings such as switches, sockets, ceiling roses, pendant holders, bracket holder, light fittings, regulators etc, including making good to disturbed surfaces of wall/floor etc, complete, all as specified & directed.

Taking down main switches, distribution boards etc of any type and capacity along with the existing boards, and removing the same from site and making good the disturbed surfaces/portion of walls etc. all as directed.

Taking down carefully existing sub main wiring with aluminium conductor/copper conductor cable of any size with GI earth wire including wooden batten etc and making good disturbed surface of walls etc, complete all as specified & directed.

Sub main wiring with two runs of 4.0 Sqmm single core FRLS PVC insulated unsheathed cable upto and including 1100 volts grade with multistranded copper conductor drawn into and including PVC concealed conduit 'ISI marked' of 20mm dia medium grade as required, fixed in concealed surface of wall/ceiling including cutting chases as required with all fittings and fixing accessories & one run of 4.00 Sqmm FRLS PVC insulated copper conductor for earth continuity wire in green color, complete all as specified & directed. Note:- Two runs of copper conductor 4.0 sqmm and one run of 4.00 Sqmm copper earth wire including PVC conduit will be measured and paid as one unit only.

Point wiring with multi stranded FRLS PVC insulated unsheathed copper conductor cable single core of 1.5 Sqmm drawn into and including PVC concealed conduit 'ISI marked' of 20mm dia medium grade as required, fixed in concealed surface of wall/ceiling including cutting chases as required, terminated in MS sunken box suitable for housing of switches, socket, regulator etc, covered with 3mm thick bakelite 'hylam' laminated sheet cover complete with all accessories including single core FRLS PVC insulated unsheathed multi stranded copper conductor cable of 1.5 sqmm for earth continuity conductor (green colour) and connected to earth dolly for one light/fan point controlled by one way switch, complete all as specified & directed.

All as per Srl item No. 68 here-in-before but for one 3/5 pin 5 Amps socket outlet on independent board.

Point wiring with multi stranded FRLS PVC insulated unsheathed copper conductor cable single core of 2.5 Sqmm drawn drawn into and including PVC concealed conduit 'ISI marked' of 20mm dia medium grade as required, fixed in concealed surface of wall/ceiling including cutting chases as required, terminated in MS sunken box suitable for housing of switches, socket, regulator etc, covered with 3mm thick bakelite 'hylam' laminated sheet cover complete with all accessories including single core FRLS PVC insulated unsheathed multi stranded copper conductor cable of 2.5 sqmm for earth continuity conductor (green colour) and connected to earth dolly for one 3/5 pin socket outlet 15 Amps independent, complete all as specified & directed. Notes for Srl Item No. 68 to 70 (i) Unit rate includes for cutting chases whereever required and sinking for boxes, making good to walls / floors etc., complete, including white wash / colour wash as directed. (ii) Uniform coding of wiring i.e red / yellow / blue for phase black for neutral and green for earth is to be maintained.

Switch socket combination, two in one, 6 pin type, 5 & 15 Amp, flush type universal, complete all as specified & directed.

Ceiling rose surface type, bakelite 65mmx50mm, 3 terminals, complete all as specified & directed.

Switch piano flush type 5 Amps 240 Volt, single pole one way, complete all as specified & directed.

Switch socket combination, two in one, 5 pin type, 5 Amp, flush type universal, complete all as specified & directed.

Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings, complete all as specified & directed.

LED lamp in white colour of 10 watt, base Cap B-22, complete all as specified & directed. Make : Philips/ Crompton/ Bajaj/ Wipro/ Syska Led/ GE Lighting/ Surya/ Havells

Sheet metal enclosure for flush/surface mounting distribution board, factory made and tested complete protection class IP-36, suitable for mounting MCBs, single pole & neutral, 240 volts with 200 amps rated copper bus bar & neutral link earthing stud, 2 way, complete all as specified & directed.

MCB, single pole & neutral, 6 to 32 Amp, AC, 10 KA repturing capacity, 240 Volt, 'C' series, complete all as specified & directed.

MCB, single pole, 6 to 32 Amp, AC, 10 KA repturing capacity, 240 Volt, 'B' series, complete all as specified & directed.

Surface & wall mounted, LED tube light fitting, 20W, glare free, smooth light distribution, 230v, box type, epoxy powder coated CRCA sheet housing with reflector cover channel, aesthetic looking end cap and HPF LED driver with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable of suitable size, complete all as specified & directed. Make. Havells, Cat Part No. ENDURALINEARNEOBS20WLED865SPCWH or equivalent in Philips/ Crompton/ Bajaj/ Wipro/ Syska Led/ GE Lighting/ Surya

Excavation in trenches not exc. 1.5m wide and not exc. 1.5m deep in any type of soil for laying of underground cable, foundation of poles & stays etc., and getting out, complete all as specified & directed.

Returning, filling in (soil), including spreading, leveling, watering and well ramming in layers not exc. 25cm, complete all as specifed & directed.

Removing excavated material to a distance not exc. 50m and depositing where directed at a level not exc. 1.5m above the starting point, complete all as specified & directed.

Sand cushioning to under ground cable, laid in trenches 8cm thick below the cable and 15cm thick above the cable after laying and stretching the cable complete punned to 18cm, complete all as specified and directed. Note:- Punned thickness of sand will be measured and paid.

Brick well burnt locally available sub class 'B' laid over sand cushioning for mechanical cable protection in trenches with width of brick perpendicular to the length of cable, complete all as specified & directed.

XLPE insulated, armoured heavy duty electric cable (heavy duty) with aluminium conductor, 1100 volts grade, cross-sectional area 16 Sqmm 2 core connected with suitable cable gland and aluminium lugs, laid in trenches or passing through pipes including testing, complete all as specified and directed. (Earth work, brick protection and sand cushioning shall be measured and paid for separately)

Junction Box made of mild steel 1.6mm thick of size 250mm x200mmx150mm including 02 Nos aluminium bus barof 2mm thick duly fitted on suitable insulator with fixing arrangement and including SP MCB 6 Amps clamped with pole complete all as specified.

Rigid non-metallic PVC conduit of 20mm dia with fixing accessories for fixing on the pole, complete all as specified & directed.

LED street light bracket made out of 40mm bore light grade pipe of 1.50m length, bent to required shape for fixing on PCC/Steel pole with 02 Nos. clamps of flat iron (40 x 6mm), nuts, bolts and washers including painting with two coats of aluminium paint over a coat of red oxide zinc chrome primer, complete all as specified and directed.

LED street light luminaries 45W LED 6000K, 230 volts, new generation energy saving & environmental friendly long life versatile pressure die-cast aluminium roadway luminaire, IP66 protection with high power LEDs as light source with toughened glass cover and all accessories, mounted on GI bracket, complete all as specified & directed. Make : Philips/ Crompton/ Bajaj/ Wipro/ Syska/ GE Lighting/ Surya

Flexible aluminium conductor PVC insulated and sheathed flat cable 1100 volts of 2.5 Sqmm twin core.

PCC 1:4:8 type D-2 using 40mm graded crushed stone aggregate as in foundation of poles etc including necessary form work, finished exposed surface even and fair without using extra cement, complete all as specified & directed.

Steel tubular swaged poles in vertical position/as strut poles swaged type 410-SP-22, 8.5 Mtr long, ISI marked complete with MS base plate of size 300x300x6mm continuously welded to pole, finial taper plug, bolts, nuts washers and screws as required duly painted with two coats of aluminium paint over a coat of red oxide primer above ground level including painting below GL (externally) with two coats of bituminous paint, numbering of poles with cut stencil lettering in size 6mm thick and 50mm high and yellow and black strips of size 30cm width each with synthetic elamel paint upto 1.5m above coping etc, complete all as specified and directed. Note:- 1. Earth work and PCC will be measured and paid seperately under appropriate items.

25mm 3-layer PP-R Polypropylene random copolymer pipes SDR 7.4 & SDR 11 UV stablised and antimicrobial welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceiling all as specified.

Ditto all as per item No. 94 here in before but size 20mm. Note : Rate are inclusive cutting chasesand making good disturbed surfaces.

Cutting in position existing GI pe both side for taking branch connection, supply and insertion of required fitting of required size fittings & fixtures for making the joint leak proof complete all as specified and directed.

5 star rated Geyser 25 ltr Cap vertical type with termostat safety valve temp change regulator and mounting on wall by grouting nuts, bolts etc and making good disturbed surfaces complete including connecting outlet/inlet pipe lones vent pipe etc all other accessories all as specified and directed by Eng-in-Charge.

1100 volts grade heavy duty electric cable PVC ivsulated aluminium conductor served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 meter apart including 4mm suspended wire one twin core cable flat or circular of cross section 6 Sqmm.

M/S Rajesh Kumar Contractor

M/s Sekinder Paul Sharma

M/S KARAN SINGH CONTRACTOR