Construction of Govt. Upper Primary Girls Residential School, Pan under Mengio Block in Papum Pare District, AP.

Amount

SH: SITE DEVELOPMENT SH : EARTH WORK

Excavation in Soil by Mechanical Means. Excavation in soil in Hilly Area by Mechanical Means including cutting and trimming of side slopes and disposing of excavated earth with all lift and lead upto 1000 metres

Excavation in Ordinary Rock by Mechanical Means not requiring Blasting Excavation in hilly area in Ordinary Rock not requiring blasting by Mechanical Means including cutting and trimming of side slopes and disposing of excavated earth with all lift and lead upto 1000 metres

SH: SCHOOL BUILDING SH: EARTH WORK

Earth work in excavation in foundation and trenches in soils containing 50% or more of shingle or small size boulders upto 30 cm size, lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers when required, into plinth, sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated soil as directed within a lead of 50m.

Re-filling excavated earth in foundations and plinth etc. in 15 cm layer including ramming and watering etc. complete.

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete.

SH: CONCRETE WORK

Providing and laying in foundations and plinth cement concrete 1 : 4 : 8 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering.

Providing and laying cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 graded stone shingle 20 mm nominal size) excluding the cost of centring and shuttering in : a) Foundations and plinth

Providing and laying damp proof course 38 mm thick with cement concrete 1 : 2 : 4 (1 cement : 2 coarse sand : 4 stone aggregate 12.5 mm nominal size).

SH: RCC WORK

Reinforcement of RCC work including bending, binding and placing in position complete.

a) Cold twisted bars.

Reinforced concrete work in foundations, footings, bases of columns etc. and mass concrete excluding cost of centring, shuttering and reinforcement in : a) M 20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforcement cement concrete work in columns, pillars, piers, abutments, post and struts etc up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but exluding cost of centring, shuttering and reinforcement. a) M 20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centering, shuttering and reinforcement. a) M 20 (1 cement : 1.5 coarse sand : 3 stone shingle 20 mm nominal size).

Reinforced cement concrete in suspended floors, roofs, landings and balconies upto floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring and shuttering and reinforcement with M 20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete in chajjas exceeding 15mm in thickness upto floor two level including centring and shuttering complete but excluding the cost of reinforcement with M20( 1 cement: 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete work in stair cases (excluding landing) except spiral cases including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface, preparing of the top surface and finishing, nosing upto floor two level but excluding the cost of centring, shuttering and reinforcement with M 20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Centring and shuttering including strutting, propping etc and removal of form work for :

a)Foundation, footings, bases of columns etc. and mass concrete.

b)Column, pillars, posts and struts etc.

c)Lintels, beams, girders, bressumers and cantilevers etc.

d)Suspended floors, roofs, landings shelves and their supports, balconies and chajjas (3.5 m height).

e)Stairs (excluding landings) except spiral stair cases.

SH: BRICK WORK

Brick work with best available local bricks in foundations and plinth in cement mortar 1:4 (1 cement : 4 fine sand).

Extra for brick work with best available local bricks in super structure above plinth level up to floor two level.

Half brick masonry with best available local bricks in cement mortar 1:4 (1 cement:4 coarse sand) in foundation and plinth

Extra for brick masonry in superstructure above plinth level up to floor two level.

SH: WOOD WORK

Providing approved best available local wood (Class - B II) work in frames of doors, windows clerestory windows and other frames, wrought framed and fixed in position.

Supplying and fixing factory made panelled shutters made out of best available hard wood for doors including panelling with panels 12 mm thick commercial veneered teak wood particle boards (Phenyle Bonded) 3 layers flat pressed including applying one coat of approved wood primer. a) 40 mm thick including anodized aluminum butt hinges with necessary screws.

Providing and fixing panelled, glazed or panelled and glazed shutters for doors, windows and clerestory windows including aluminium butt hinges with necessary screws. a) 38mm thick best available local wood class - B I

Providing and fixing MS grills of required pattern in wooden frames of windows etc with MS flat, square or round bars with round headed bolts and nuts or by screws. a) Plain grill.

Providing and fixing aluminum sliding door bolts anodised transparent or dyed to required color or shade with nuts and screws etc complete. a) 300 x 16 mm

Providing and fixing aluminum Tower bolts anodized or transparent or dyed to required color or shade with necessary screws etc complete. a) 250 x 10 mm

Providing and fixing aluminum Handles anodised transparent or dyed to required color or shade with necessary screws etc complete.

Providing and fixing MS Hooks and Eyes. d) 150 mm

Providing and fixing 12 mm thick and 100 mm wide pelmet with 25 mm dia wooden curtain rod and brackets including fixing with 25 x 3 mm MS flat 10 cm long and plugs etc complete. a) Timber class - A IV

SH: STEEL WORK

Providing and fixing MS fan clamp type I of 16 mm dia MS bar bent to shape with hooked ends in RCC slabs during lying including painting the exposed portion of loop all as per standard design complete.

Providing and fixing MS round holding down bolts with nuts and washer plates etc complete.

Providing and fixing stainless steel railing made of hollow tubes, channels, plates etc. Including welding, grinding, buffing, polishing and making curvature and fitting the same with necessary stainless steel nuts and bolts complete i/c fixing of railing with necessary accessories and stainless steel dash fasteners, stainless sttel bolts etc of required size, on the top of the floor or side of waist slab with suitable arrangement as per approval of engineer-in-charge.

SH: FLOORING

Providing and Laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and confirming to IS: 15622 of approved make, in all colours and shades laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with white cement and matching pigments etc complete.

c) Size of Tile 600 x 600 mm

White glazed tiles 5mm.thick in flooring, skirting, risers of step and dado in 12 mm thick cement plaster 1 : 3(1 cement: 3 coarse sand) painted with white cement slurry.

SH: ROOFING

Providing and fixing on wall face C.I. rain water pipe including filling the joints with spun yarn soaked in neat cement slurry and cement mortar 1 : 2 ( 1 cement : 2 fine sand). b) 100 mm diameter pipe

Providing and fixing M.S. Holder bat clamps of approved design of C.I. or S.C.I. pipes embedded in and including cement concrete block 10 cm x 10 cm x 10 cm of 1 : 2 : 4 mix (1 cement : 2 coarse sand: 4 stone aggregate 20mm nominal size) including cost of cutting holes and making good the wall etc. (a)100 mm diameter

Providing and fixing on wall face C.I. accessories for rain water pipes including filling the joints with spun yarn soaked in neat cement slurry and cement mortar 1 : 2 ( 1 cement: 2 fine sand).

(A) CI Plain bend (a)100 mm diameter

(B) CI head flat or corner type bend : (a) 100 mm diameter

SH: FINISHING

15 mm cement plaster 1 : 4 (1 cement : 4 fine sand) on the rough side of single or half brick wall.

12 mm cement plaster 1 : 4 (1 cement : 4 fine sand).

6 mm cement plaster to ceiling 1 : 3 (1 cement : 3 fine sand).

Neat cement punning.

Distempering (two or more coats) with oil bound washable distemper of approved brand and manufacture and of required shade on new work over and including a priming coat with distemper primer of approved brand and manufacture to give an even shade.

Applying one coat of distemper primer of approved brand and manufacture on wall surface.

Applying priming coat with ready mixed pink primer of approved brand and manufacture on wood work complete.

Painting two coats with oil type wood preservative of approved brand and manufacture on new work.

Applying priming coat with ready mixed primer of approved brand and manufacture on steel work.

Painting two or more coats (excluding priming coat) with superior ready mixed paint for steel work of approved brand and manufacture in all shades on new work to give an even shade.

SH: MISCELLANIOUS

Making plinth protection 50 mm thick of cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 stone aggregate using 20 mm nominal size) over 75 mm bed of stone ballast 40 mm nominal size well rammed and consolidated and grouted with fine sand including finsihing the top smooth.

SH: DRAINAGE

Construction of cement concrete drain 30 cm wide and 23 cm deep in cement concrete 1 : 3 : 6 (1 cement : 3 sand : 6 hard graded stone chips/shingle 40 mm and down gauge) 8 cm thick on sides and bottom and plastering on all exposed surfaces with 12 mm thick cement mortar1 : 3 (1 cement : 3 fine sand) including shuttering complete.

Providing and laying cement concrete 1 : 5 : 10 (1 cement : 5 lime sand : 10 graded stone aggregate 40 mm nominal size) all around SW Pipe including bed concrete 15 cm thick as per standard design. a) 100 mm dia SW pipes

Constructing brick masonry manhole with 2nd class bricks in cement mortar 1 : 5 (1 cement :5 fine sand) RCC top slab with 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 stone single 20 mm nominal size), foundation concrete 1 : 4 : 8 mix (1 cement : 4 coarse sand : 8 stone aggregate 40 mm nominal size) inside plastering 12 mm thick with cement mortar 1 : 3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size) neatly finished complete as per standard design.

a) Inside size 90 x 80 cm and 45 cm deep including CI cover with frame (light duty) 455 x 610 mm internal dimensions total weight of cover and frame to be not less than 38 Kg (weight of cover and frame to be not less than 38 kg, (weight of cover 23 Kg and weight of frame 15 Kg).

Making soak pit 2.50 M dia 3.00 M deep with 45x45 cm dry brick honeycomp shaft and SW drain pipe 100 mm dia and 1.20 M long complete as per standard design.

SH: WATER SUPPLY

Providing and fixing GI pipes complete with GI fittings and clamps including cutting and making good the walls (internal work).

a) 15 mm nominal bore

b) 20 mm nominal bore

Providing and fixing GI pipes complete with GI fittings including trenching and refilling etc. (external work). b) 20 mm nominal bore

Providing and fixing brass bib cock of approved quality.

a) 15 mm nominal bore

b) 20 mm nominal bore

Providing and fixing brass stop cock of approved quality.

a) 15 mm nominal bore

b) 20 mm nominal bore

Providing and fixing PVC connection pipe with brass union. A) 30 cm length a) 15 mm nominal bore

SH: SANITARY INSTALLATION

Providing and fixing white vitreous china water closet squating pan (Indian type WC pan) size 580 mm with 100 mm and sand cast iron P or S trap, 12.5 Litre high level CI flushing cistern (of approved make) with fittings RS or CI brackets, 32 mm dia galvanized steel telescopic flush pipe with fittings and clamps 20 mm GI over flow pipe with specials and mosquito proof coupling of approved municipal design and GI chain and pull complete including painting of cistern and fittings, cutting and making good the walls and floors where required. a) Long Pan patten WC Pan

Providing and fixing white vitreous china type water closet pedestal (European type WC pan) with seat and lid CP brass hinges and rubber buffers, 12.5 Litres high level CI flushing cistern with fittings RS or CI brackets, galvanized steel telescopic flush pipe with fittings and clamps, 20 GI overflow pipe with specials and mosquito proof coupling of approved municipal design and GI chain and pull complete including painting of cistern and fittings, cutting making good the walls and floors where required. a) WC pan with white plastic seat and lid.

Providing and fixing white vitreous china wash basin with RS or CI brackets painted white 15 mm CP brass pillar taps and CP brass chain with rubber plug 32 mm CP brass waste of standard pattern, 32 mm dia CP brass trap and MI unions complete, including cutting and making good the walls where required. a) Flat back wash basin size 550x400 mm with a pair of 15 mm CP brass pillar taps of heavy quality.

Providing and fixing a pair of white vitreous china foot rest of standard pattern for squatting pan WC. b) 250 x 125 x 25 mm

Providing and fixing kitchen sink including making all connection excluding cost of fittings. a) White glazed fire clay sink size 600x450x150 mm

Providing and fixing 100 mm sand cast iron grating for gulley, floors or nahni trap.

Providing and fixing 600x450 mm bevelled edge mirror or superior glass (of approved quality) complete with 6 mm thick asbestos sheet ground fixed to wooden cleadt with CP brass screws and washers.

Providing and fixing 600 x 120 mm glass shelf with CP brass brackets and guard rail complete, fixed to wooden cleadts with CP brass screws.

Providing and fixing CP brass towel rail complete with CP brass brackets fixed to wooden cleadt with CP brass screws (heavy quality). a) 750 x 20 mm size

Providing and fixing toilet paper holder. a) CP Brass

Providing and fixing CP brass waste for wash basins and sinks. a) 32 mm dia

Providing and fixing sand cast iron/ cast iron (spun) soil, waste and vent pipes.

a) 100 mm dia

b) 75 mm dia

Providing and fixing sand cast iron heel rest sanitary bend.

a) 100 mm dia

b) 75 mm dia

Providing and fixing sand cast iron trap of self cleadnsing design with sand cast iron screwed down or hinged grating with or without vent arm complete including cost of cutting and making good the walls and floors. a) 100 mm inlet and 100 mm outlet

Providing and fixing CP brass shower rose with 15 mm or 20 mm dia inlet. a) 100 mm dia

SH: SEPTIC TANK FOR 100 USERS

Earth work in excavation in foundation and trenches in soils containing 50% or more of shingle or small size boulders upto 30 cm size, lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers when required, into plinth, sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated soil as directed within a lead of 50m.

Providing and laying cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) excluding the cost of centring and shuttering in : (a) Foundations and plinth

Brick work with best available local bricks in foundations and plinth in cement mortar 1:4 (1 cement : 4 fine sand).

Reinforcement of RCC work including bending, binding and placing in position complete (b) Cold twisted bars.

Providing, hoisting and fixing up to floor two level pre-cast reinforced cement concrete in vertical and horizontal fins individually or forming box louvers and bands including finishing and plastering with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm on exposed surface to give a smooth and even surface, centering and shuttering and shetting in position with cement mortar 1 : 2 (1 cement : 2 fine sand) etc but excluding cost of reinforcement with 1 : 2 : 4 (1 cement : 2 coarse sand : 4 stone shingle 20 mm nominal size).

6 mm cement plaster to ceiling 1 : 3 (1 cement : 3 fine sand).

Neat cement punning.

12 mm cement plaster 1:3 (1 cement : 3 fine sand).

Providing and fixing on wall face asbestos cement soil, waste and vent pipes including jointing with spun yarn soaked in bitumen and cement mortar 1 : 2 (1 cement : 2 coarse sand) complete. (a) 100 mm dia

Providing and fixing sand cast iron trap of self cleadnsing design with sand cast iron screwed down or hinged grating with or without vent arm complete including cost of cutting and making good the walls and floors. (a) 100 mm inlet and 100 mm outlet

SH: HOSTEL BUILDING (GIRLS) SH: EARTH WORK

Earth work in excavation in foundation and trenches in soils containing 50% or more of shingle or small size boulders upto 30 cm size, lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers when required, into plinth, sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated soil as directed within a lead of 50m.

Re-filling excavated earth in foundations and plinth etc. in 15 cm layer including ramming and watering etc. complete.

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete.

SH: CONCRETE WORK

Providing and laying in foundations and plinth cement concrete 1 : 4 : 8 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering.

Providing and laying cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 graded stone shingle 20 mm nominal size) excluding the cost of centring and shuttering in : a) Foundations and plinth

Providing and laying damp proof course 38 mm thick with cement concrete 1 : 2 : 4 (1 cement : 2 coarse sand : 4 stone aggregate 12.5 mm nominal size).

SH: RCC WORK

Reinforcement of RCC work including bending, binding and placing in position complete. a) Cold Twisted Bars.

Reinforced concrete work in foundations, footings, bases of columns etc. and mass concrete excluding cost of centring, shuttering and reinforcement in : a) M 20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforcement cement concrete work in columns, pillars, piers, abutments, post and struts etc up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but exluding cost of centring, shuttering and reinforcement. a) M 20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centering, shuttering and reinforcement. a) M 20 (1 cement : 1.5 coarse sand : 3 stone shingle 20 mm nominal size).

Reinforced cement concrete in suspended floors, roofs, landings and balconies upto floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring and shuttering and reinforcement with M 20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete work in stair cases (excluding landing) except spiral cases including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface, preparing of the top surface and finishing, nosing upto floor two level but excluding the cost of centring, shuttering and reinforcement with M 20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Centring and shuttering including strutting, propping etc and removal of form work for :

a)Foundation, footings, bases of columns etc. and mass concrete.

b)Column, pillars, posts and struts etc.

c)Lintels, beams, girders, bressumers and cantilevers etc.

d)Suspended floors, roofs, landings shelves and their supports, balconies and chajjas (3.5 m height).

e)Stairs (excluding landings) except spiral stair cases.

SH: BRICK WORK

Brick work with best available local bricks in foundations and plinth in cement mortar 1:4 (1 cement : 4 fine sand).

Extra for brick work with best available local bricks in super structure above plinth level up to floor two level.

Half brick masonry with best available local bricks in cement mortar 1:4 (1 cement:4 coarse sand) in foundation and plinth

Extra for brick masonry in superstructure above plinth level up to floor two level.

SH: WOOD WORK

Providing approved best available local wood (Class - B II) work in frames of doors, windows clerestory windows and other frames, wrought framed and fixed in position.

Supplying and fixing factory made panelled shutters made out of best available hard wood for doors including panelling with panels 12 mm thick commercial veneered teak wood particle boards (Phenyle Bonded) 3 layers flat pressed including applying one coat of approved wood primer. a) 40 mm thick including anodized aluminum butt hinges with necessary screws.

Providing and fixing panelled, glazed or panelled and glazed shutters for doors, windows and clerestory windows including aluminium butt hinges with necessary screws. a) 38mm thick best available local wood class - B I

Providing and fixing MS grills of required pattern in wooden frames of windows etc with MS flat, square or round bars with round headed bolts and nuts or by screws. a) Plain grill.

Providing and fixing aluminum sliding door bolts anodised transparent or dyed to required color or shade with nuts and screws etc complete. a) 300 x 16 mm

Providing and fixing aluminum Tower bolts anodized or transparent or dyed to required color or shade with necessary screws etc complete. a) 250 x 10 mm

Providing and fixing aluminum Handles anodised transparent or dyed to required color or shade with necessary screws etc complete.

Providing and fixing MS Hooks and Eyes. d) 150 mm

Providing and fixing 12 mm thick and 100 mm wide pelmet with 25 mm dia wooden curtain rod and brackets including fixing with 25 x 3 mm MS flat 10 cm long and plugs etc complete. a) Timber class - A IV

SH: STEEL WORK

Providing and fixing MS fan clamp type I of 16 mm dia MS bar bent to shape with hooked ends in RCC slabs during lying including painting the exposed portion of loop all as per standard design complete.

Providing and fixing MS round holding down bolts with nuts and washer plates etc complete.

Providing and fixing stainless steel railing made of hollow tubes, channels, plates etc. Including welding, grinding, buffing, polishing and making curvature and fitting the same with necessary stainless steel nuts and bolts complete i/c fixing of railing with necessary accessories and stainless steel dash fasteners, stainless sttel bolts etc of required size, on the top of the floor or side of waist slab with suitable arrangement as per approval of engineer-in-charge.

SH: FLOORING

Cement concrete flooring 1 : 2 : 4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement. 40 mm thick

Providing and Laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and confirming to IS: 15622 of approved make, in all colours and shades laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with white cement and matching pigments etc complete. c) Size of Tile 600 x 600 mm

White glazed tiles 5mm.thick in flooring, skirting, risers of step and dado in 12 mm thick cement plaster 1 : 3(1 cement: 3 coarse sand) painted with white cement slurry.

SH: ROOFING

Providing and fixing on wall face C.I. rain water pipe including filling the joints with spun yarn soaked in neat cement slurry and cement mortar 1 : 2 ( 1 cement : 2 fine sand). b) 100 mm diameter pipe

Providing and fixing M.S. Holder bat clamps of approved design of C.I. or S.C.I. pipes embedded in and including cement concrete block 10 cm x 10 cm x 10 cm of 1 : 2 : 4 mix (1 cement : 2 coarse sand: 4 stone aggregate 20mm nominal size) including cost of cutting holes and making good the wall etc. (a)100 mm diameter

Providing and fixing on wall face C.I. accessories for rain water pipes including filling the joints with spun yarn soaked in neat cement slurry and cement mortar 1 : 2 ( 1 cement: 2 fine sand). (A) CI Plain bend (a)100 mm diameter

(B) CI head flat or corner type bend : (a) 100 mm diameter

SH: FINISHING

15 mm cement plaster 1 : 4 (1 cement : 4 fine sand) on the rough side of single or half brick wall.

12 mm cement plaster 1 : 4 (1 cement : 4 fine sand).

Neat cement punning.

Distempering (two or more coats) with oil bound washable distemper of approved brand and manufacture and of required shade on new work over and including a priming coat with distemper primer of approved brand and manufacture to give an even shade.

Applying one coat of distemper primer of approved brand and manufacture on wall surface.

Applying priming coat with ready mixed pink primer of approved brand and manufacture on wood work complete.

Painting two coats with oil type wood preservative of approved brand and manufacture on new work.

Applying priming coat with ready mixed primer of approved brand and manufacture on steel work.

Painting two or more coats (excluding priming coat) with superior ready mixed paint for steel work of approved brand and manufacture in all shades on new work to give an even shade.

SH: MISCELLANIOUS

Making plinth protection 50 mm thick of cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 stone aggregate using 20 mm nominal size) over 75 mm bed of stone ballast 40 mm nominal size well rammed and consolidated and grouted with fine sand including finsihing the top smooth.

SH: DRAINAGE

Construction of cement concrete drain 30 cm wide and 23 cm deep in cement concrete 1 : 3 : 6 (1 cement : 3 sand : 6 hard graded stone chips/shingle 40 mm and down gauge) 8 cm thick on sides and bottom and plastering on all exposed surfaces with 12 mm thick cement mortar1 : 3 (1 cement : 3 fine sand) including shuttering complete.

Providing and laying cement concrete 1 : 5 : 10 (1 cement : 5 lime sand : 10 graded stone aggregate 40 mm nominal size) all around SW Pipe including bed concrete 15 cm thick as per standard design. a) 100 mm dia SW pipes

Constructing brick masonry manhole with 2nd class bricks in cement mortar 1 : 5 (1 cement :5 fine sand) RCC top slab with 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 stone single 20 mm nominal size), foundation concrete 1 : 4 : 8 mix (1 cement : 4 coarse sand : 8 stone aggregate 40 mm nominal size) inside plastering 12 mm thick with cement mortar 1 : 3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size) neatly finished complete as per standard design.

a) Inside size 90 x 80 cm and 45 cm deep including CI cover with frame (light duty) 455 x 610 mm internal dimensions total weight of cover and frame to be not less than 38 Kg (weight of cover and frame to be not less than 38 kg, (weight of cover 23 Kg and weight of frame 15 Kg).

Making soak pit 2.50 M dia 3.00 M deep with 45x45 cm dry brick honeycomp shaft and SW drain pipe 100 mm dia and 1.20 M long complete as per standard design.

SH: WATER SUPPLY

Providing and fixing GI pipes complete with GI fittings and clamps including cutting and making good the walls (internal work).

a) 15 mm nominal bore

b) 20 mm nominal bore

Providing and fixing GI pipes complete with GI fittings including trenching and refilling etc. (external work). b) 20 mm nominal bore

Providing and fixing brass bib cock of approved quality.

a) 15 mm nominal bore

b) 20 mm nominal bore

Providing and fixing brass stop cock of approved quality.

a) 15 mm nominal bore

b) 20 mm nominal bore

Providing and fixing PVC connection pipe with brass union. A) 30 cm length a) 15 mm nominal bore

SH: SANITARY INSTALLATION

Providing and fixing white vitreous china water closet squating pan (Indian type WC pan) size 580 mm with 100 mm and sand cast iron P or S trap, 12.5 Litre high level CI flushing cistern (of approved make) with fittings RS or CI brackets, 32 mm dia galvanized steel telescopic flush pipe with fittings and clamps 20 mm GI over flow pipe with specials and mosquito proof coupling of approved municipal design and GI chain and pull complete including painting of cistern and fittings, cutting and making good the walls and floors where required. a) Long Pan patten WC Pan

Providing and fixing white vitreous china type water closet pedestal (European type WC pan) with seat and lid CP brass hinges and rubber buffers, 12.5 Litres high level CI flushing cistern with fittings RS or CI brackets, galvanized steel telescopic flush pipe with fittings and clamps, 20 GI overflow pipe with specials and mosquito proof coupling of approved municipal design and GI chain and pull complete including painting of cistern and fittings, cutting making good the walls and floors where required. a) WC pan with white plastic seat and lid.

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x430x265 mm sizes respectively with CI automatic flushing cistern with fittings, RS or CI brackets standard size galvanized steel flush pipe and spreaders with brass unions and GI clamps complete including painting of cistern and fittings, cutting and making good the walls and floors where required. b) Range of two urinals with 10 Litre CI automatic flushing cistern

Providing and fixing white vitreous china wash basin with RS or CI brackets painted white 15 mm CP brass pillar taps and CP brass chain with rubber plug 32 mm CP brass waste of standard pattern, 32 mm dia CP brass trap and MI unions complete, including cutting and making good the walls where required. a) Flat back wash basin size 550x400 mm with a pair of 15 mm CP brass pillar taps of heavy quality.

Providing and fixing a pair of white vitreous china foot rest of standard pattern for squatting pan WC. b) 250 x 125 x 25 mm

Providing and fixing kitchen sink including making all connection excluding cost of fittings. a) White glazed fire clay sink size 600x450x150 mm

Providing and fixing 100 mm sand cast iron grating for gulley, floors or nahni trap.

Providing and fixing 600x450 mm bevelled edge mirror or superior glass (of approved quality) complete with 6 mm thick asbestos sheet ground fixed to wooden cleadt with CP brass screws and washers.

Providing and fixing 600 x 120 mm glass shelf with CP brass brackets and guard rail complete, fixed to wooden cleadts with CP brass screws.

Providing and fixing CP brass towel rail complete with CP brass brackets fixed to wooden cleadt with CP brass screws (heavy quality). a) 750 x 20 mm size

Providing and fixing toilet paper holder. a) CP Brass

Providing and fixing CP brass waste for wash basins and sinks. a) 32 mm dia

Providing and fixing sand cast iron/ cast iron (spun) soil, waste and vent pipes.

a) 100 mm dia

b) 75 mm dia

Providing and fixing sand cast iron heel rest sanitary bend.

a) 100 mm dia

b) 75 mm dia

Providing and fixing sand cast iron trap of self cleadnsing design with sand cast iron screwed down or hinged grating with or without vent arm complete including cost of cutting and making good the walls and floors. a) 100 mm inlet and 100 mm outlet

Providing and fixing CP brass shower rose with 15 mm or 20 mm dia inlet. a) 100 mm dia

SH: SEPTIC TANK FOR 100 USERS

Earth work in excavation in foundation and trenches in soils containing 50% or more of shingle or small size boulders upto 30 cm size, lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers when required, into plinth, sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated soil as directed within a lead of 50m.

Providing and laying cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) excluding the cost of centring and shuttering in : (a) Foundations and plinth

Brick work with best available local bricks in foundations and plinth in cement mortar 1:4 (1 cement : 4 fine sand).

Reinforcement of RCC work including bending, binding and placing in position complete (b) Cold twisted bars.

Providing, hoisting and fixing up to floor two level pre-cast reinforced cement concrete in vertical and horizontal fins individually or forming box louvers and bands including finishing and plastering with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm on exposed surface to give a smooth and even surface, centering and shuttering and shetting in position with cement mortar 1 : 2 (1 cement : 2 fine sand) etc but excluding cost of reinforcement with 1 : 2 : 4 (1 cement : 2 coarse sand : 4 stone shingle 20 mm nominal size).

6 mm cement plaster to ceiling 1 : 3 (1 cement : 3 fine sand).

Neat cement punning.

12 mm cement plaster 1:3 (1 cement : 3 fine sand).

Providing and fixing on wall face asbestos cement soil, waste and vent pipes including jointing with spun yarn soaked in bitumen and cement mortar 1 : 2 (1 cement : 2 coarse sand) complete. (a) 100 mm dia

Providing and fixing sand cast iron trap of self cleadnsing design with sand cast iron screwed down or hinged grating with or without vent arm complete including cost of cutting and making good the walls and floors. (a) 100 mm inlet and 100 mm outlet

M/S Taya Construction Agency

M/S Tana Tedi Tara