PERIODICAL SERVICES, REPAIR/REPLACEMENT OF EXISTING ROOFTREATMENT, PLUMBING, JOINERY IN CERTAIN MD/ OTM ACCN INCLUDING WELCOME MAINT TO OFFR MD ACCN UNDER ZONE-I AT JAIPUR MIL STN

Amount

M & L for preparation of old decorated surfaces of walls, pillars and cornices including brooming down and cleaning the surface and applying one coat of white wash all as specified and directed

All as per item No 1 above but two coats of white wash on wall

M & L for preparation of old plastered or unplastered decorated surfaces and applying one coat of white wash on ceiling

All as per item No 3 above but two coats of white wash on ceiling.

M&L for preparing of old decorated surfaces of (plastered or unplastered) including cornices pillasters and other wall features by washing, rubbing down and stopping of distemper white or tinted incluidng filling of any minor hole/ depression with wall care putty and scaffolding arrangement , trestles, ladders etc all as specified and directed.

M&L for complete removal of existing treatment including cleaning of mortar drops, smoke soot, moulds, moss, efflorescent salts, trading oil, greasy spots etc and preparation of plastered surfaces incluiding filling of depressions etc and applying two coats of oil bound distemper of approved tint.

M&L of one coat of Birla wall care putty on walls etc.

M & L for preparation of old plastered or unplastered decorated surfaces and applying one coat of oil bound distemper on ceiling

M & L for preparation of old painted wooden surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint of any tint all as specified and directed.

M & L for preparation of old painted steel surfaces of any description over 10cm in width or girth and applying one coat of synthetic enamel paint of any tint all as specified and directed

M&L for preparation of old descorated plastered / unplastered surfaces of walls, soffits of chajja, cornices etc and applying one coat of cement base paint upto two storey building including scaffloding arrangement all as specified and directed by Engineer-in-Charge.

All as per item 11 above and applying two coats of cement base paint

M&L for preparation of old decorated plastered/ unplastered surfaces of edges, facia & projection etc and applying two coats of exterior acrylic emulsion (APEX) upto two storey building incluidng scaffolding arrangement all as specified and directed .

All as per item No 13 above but two coats of exterior acrylic emulsion (APEX) all as specified and directed .

Taking down cement plaster on brick / stone wall, ceiling etc incl. raking outs joints, hacking for key, scrubbing with water etc.

M & L for rendering 15 mm thick on stone masonary surface or surface other than fair faces of brick work or on one side of lathing in CM 1:6 finished even and smooth without using extra cement

M & L for rendering 15 mm thick on stone masonary surface or surface other than fair faces of brick work in CM 1:4 finished even and smooth without using extra cement all as specified and directed .

M & L rendering 10 mm thick on brick work or concrete surfaces in ceiling in CM 1:3 finished finished even and smooth without using extra cement all as specified and directed .

M & L for preparation of new plastered surfaces of ceiling and applying three coats of white wash on ceiling all as specified and directed .

M & L for preparation of new plastered wall surfaces and applying two coats of cement base paint on wall all as specified and directed .

M & L for preparation of new plastered wall surfaces and applying two coat of oil bound distemper of any tint including priming plastered surfaces with alkali resistant priming paint all as specified and directed .

M & L for preparation of new plastered wall surfaces and applying three coats of white wash on walls

M & L GI wire netting 0.90mm dia and 12mm mesh lathing to metal studding etc in ceilings including all laps, cutting and waste in repairs in patches n exc 5 sqm each including taking down old and jointing new to old as required.

M & L Dubbing out average 10mm thick cement plaster 1:4 on irregular face of ceiling all as specified and directed .

Raking out joints/ pointing to random rubble uncoursed or brought up to courses work built in cement mortar complete

M & L Keyed pointing to random rubble uncoursed or brought up to courses in cement mortar in CM 1:3 complete

M & L taking down existing treatment of chajja and applying 15mm thick plastering to chajjas in CM 1:3 including making dripping/ throating and PCC 1:2:4 for covering making proper slope etc complete at ground/ first floor all as specified and as directed

S&F in repair CP fancy type centre hole basin mixed 15mm bore chromium plated alloy with 450mm copper hose / braided hose without popup waste system quarter turn and fixed complete all as specified.

S&F in repair CP wall mixer with flange & 15mm long bend pipe for over head shower non Telephonic type with connecting legs wall flanges and crutch etc quarter turn 15mm bore for mixing hot & cold water and complete all as specified

S&F in repair CP cast copper alloy bib taps short body with wall flange fancy type of 15mm bore quarter turn, complete all as specified

S&F in repair fancy type pillar cock 15mm bore cast copper alloy with capstan heads chromium plated, screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts all as specified

S&F in repair Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (minimum weight 15mm- 142 gms)

S&F in repair Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (minimum weight 20mm- 210 gms)

S&F in repair PVC connection 15mm dia 45cm long with 2 Nos brass check nuts with washer complete all as specified

S&F in repair PVC connection 15mm dia 60cm long with 2 Nos brass check nuts with washer complete all as specified

S&F in repair of chromium plated overhead shower with revolving joint and 125mm long shower arm with wall falnge 15mm bore fancy type any colour complete all as specified

S&F in repair 32mm dia PVC waste pipe flexible type for WHB 60cm long with union all as specified

S&F in repair waste fittings brass chromium plated 32mm dia for wash hand basin all as specified

All as per item No 38 above but 100mm dia for stainless steel sink

All as per item No 38 above but 75mm dia for stainless steel sink

S&F in repair galvanised steel (GI) water tubing medium grade with all fittings and fixed complete to walls and celing or laid in floors of 15mm bore all as specified and directed .

S&F in repair galvanised steel (GI) water tubing medium grade with all fittings and fixed complete to walls and celing or laid in floors of 20mm bore all as specified and directed

S&F in repair small fittings galvanised iron medium grade such as sockets, elbow, nipple upto 200mm, tee, union, reducer socket, reducer tee, tee, union etc for 15mm bore

S&F in repair small fittings galvanised iron medium grade such as sockets, elbow, nipple upto 200mm, tee, union, reducer socket, reducer tee, tee, union etc for 20mm bore

S&F in repair flush pipe of PVC of low or high density 32mm dia, for low level cistern complete all as specified

S&F in repair plastic water closet seat cover white/ colour, closed pattern with flat bottom end cover and mild steel chromium plated hanging device complete all as specified

S&F in repair vitreous china wash hand basin flat back basin including half pedastal, coloured, size of 550 x 400mm including CP waste coupling but excluding taps, waste chan & plug complete all as specified

Dismantling old unserviceable PVC/ RCC water tank complete all as directed capacity exceeding 250 ltr and not exc 500 ltrs

All as per item No 48 above but exc 500 ltr but not exc 1000 ltr

S & F 500 Ltrs capacity rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) hoisted and fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe pipe etc complete all as specified in SSR Part I, Make - Sintex or eqivalent

All as per item No 50 above but 1000 ltrs capacity

S&F in repair PVC syphone set with handle complete for low level flushing cistern complete

S&F in repair CP grating 125mm dia round fix on floor/ nahani trap fixed with cement mortar complete all as directed

S&F in repair CP brass bottle trap 32mm dia including joining to waste fitting and waste pipe complete all as directed

Dismantling of old unserviceable trap and S&F of PVC Nahani / floor trap and square in size of 100 x 100mm including MS chromium plated grating 125mm dia of weight not less than 50gm for floor trap/ Nahani trap

S&F in repair of CP cast copper alloy bib taps long body with wall flange fancy type of 15mm bore half turn complete all as specified

S & F as in repair stop valves cast copper alloy, fancy type chromium plated with long shank and cup (concealed type), screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or for unions in 15 mm bore fixed .

S & F as in repair angle stop valves cast copper alloy, fancy type chromium plated, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or for unions in 15 mm bore fixed

S&F sink with drainage board made of stainless steel 1.0mm thick for kitchen with plugs, washers and wastes, including bedding in cement mortar on to dwarf wall or with 7 including fixing cantilever brackets and connecting union to pipe, overall size 1120mm x 457mm bowl size 460 x 330 x 203mm includng waste pipe of polythelene of flow or high density or PVC 32mm dia & waste fitting brass chromium plated for 32mm bore with long screwed shanks and fly nuts including making holes in stone walls for brackets and fixed in CM 1:3 or PCC 1:2:4 type B0 complete including taking down of existing old sink.

M&L in repair spindles for 15mm CP brass bib cock/ stop cocks etc size 1 nos to 4 nos for full turns/ half turns complete as directed

Disconnecting existing tanks of cap 500 Ltrs, setting aside (or lowering if required) for repairs, cleaning etc and hoisting if required reconnecting and re-fixing in position. (Cleaning repairing etc measured separately)

All as per item No 61 above but 1000 ltrs capacity

S & F Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed bore dia of pipe 20mm

S&F in repairs PVC sintex water storage tank lid cover ( cylindrical) for 500 ltrs capacity tanks

Demolition of old existing unserviceable EWC seat and S&F vitreous china wash down water closet pan ( pedestal pattern) white including connections to drain ( or outgoing pipe) and to flushing pipe anti sypohonage pipe etc & with plastic WC seat cover white closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinges device complete

S & F in repair vitreous china squatting pan 'Orissa' pattern water closet white size 580mm x 440mm with integral foot rest (excluding flushing cistern and flush pipe) complete incl connection to trap & flushing pipe antisyphonage pipe etc

S & F in repair PVC valveless, syphonic action type flushing cistern 10 lirs capacity, low level, white with inlet, ball valve, float and handle incl brackets & flush pipe of polyethylene of low or high density or PVC, 32mm dia suitable for low level cistern,

S & F as in repair stop valves cast copper alloy screwed down high pressure with crutch or butter fly handle, screwed both ends for iron pipe or for unions in 15 mm bore fixed

S & F as in repair stop valves cast copper alloy screwed down high pressure with crutch or butter fly handle, screwed both ends for iron pipe or for unions in 20 mm bore fixed

S&F toilet paper holder for CP fixed to walls with chromium plated (CP) brass screws fixed in repair

S&F in repair CP cast copper alloy bib taps two ways with wall flange and areator fancy type of 15mm bore quarter turn complete all as specified

S&F in repair CP health foucet with chain of 15mm bore complete all as specified

S&F in repair of bathroom glass corner of best quality complete all as specified and directed.

S&F in repair of wooden beads 2nd class hard wood of any size for cup board & glazed or gauged joinery mitres etc all as directed by Engr-in-Charge

S&F in repair 20mm dia mild steel conduit with bright finish pipe of required length for curtain rods as specified and directed.

S&F in repair MS chromium plated bracket holder for curtain rods 20mm dia fixed with screws to pelmet boxes all as specified and directed.

S & F in repair stainless steel kitchen plate rack of overall minimum size 900 x 750 x 225mm with partitions for small/ large plates etc made out of stainless steel 24 gauge, fixed with rawl plug and CP steel screws all as directed of approved quality all as specified and directed.

S & F in repair drapery rod PVC insulated 25 mm dia incl fixing brackets and decorative knobs on each end of rod of approved pattern and colour complete including taking down old curtain rod with brackets all as specified and directed.

S&F in repair steel window handles, box type hinges and peg stay etc including welding if required all as specified

S&F in repair cupboard handle and lock godrej pattern fixed with screws, nut bolts etc including washer of mild steel bright finish all as specified

S & F in repair galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks, or galvanised wire staples

Hacking out old broken glass any thickness size, quality or description from wooden/ steel frames fixed with beads/ metal pinning , S&F 3mm thick sgeet glass in square not exc 0.50 Sqm in each pane fixed with wooden beads or putty ( in metal frames etc) complete all as specified

All as per item No 82 above but pin headed figured glass 4mm thick

Dismantling boarding plywood etc of any description and in any position fixed with nails etc all as directed.

M&L 19mm thick block board/ commercial board grade 2 quality interior grade commercial type fixed with screwes to timber frame work for kitchen cabinet shutter / Almirah shutter etc including of two coats of synthetic enamel paint over a coat of pink primer after preparation of surface

M&L 19mm thick prelaminated particles board, interior grade, prelaminated both side with decorative choice lamination, fixed with screws to timber frame work

M&L 6mm thick plywood, grade BWP, type BB fixed with nails to timber frame work of shutter and similar works all as specified and directed.

M&L 19mm thick MDF membrane kitchen cabinets door shutter in wood grain colour, half round edge fixed in repair all as specified and directed.

S&F Auto close hinges, stainless steel, bright finish or electrogalvanised.

S&F brass handle of 100mm size type polished bright

M&L of kitchen basket stainless steel size 435mm x 510mm including stainless stee; guide channel fixed in repair.

S & F in repair aluminium floor door stopper 75mm size with double pin and rubber shoe fixed to bottom rail of door shutter complete

S&F in repair box type mirror PVC cabinet of size 475 x 600 x 150mm all as specified

S&F in repair vitreous china water closet Indian type 580mm long pan white with 'P' or 'S' trap front or back inlet footrest including provn of cement concrete bedding including connections to flushing cistern / pipe and making good disturbed portion to match with existing surface complete all as directed.

Dismantling plain or corrugated steel / FRP sheeting any gauge, thickness including nainital or similar pattern roof /wall covering

Dismantling wrought iron or mild steel work of any description nototherwise provided for

S & F steel work in tubular/ square/ rectangular trusses incl special shaped washer etc, complete using ERW orinduction butt welded tubes conforiming toIS 1161-1979 graded St-240

M & L Preparing newly untreated steel surfaces of any descripton over 10 cm wiidth or girth and applying two coat of synthetic enamel paints over a coat of red oxide primer

S&F 2mm thick fibre glass reinforced translucent corrugated sheeting with two corrugation side lap fixed with coarch screw and washer in roof wall etc

M&L pre- painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550Mpa as in roof covering / cladding to wall, fixed with self tapping screws as specified

M&L scrapping roof surface with wire brushes and washing with water etc including taking down old cement plaster, PCC of any thickness, description in any situation ,position and roof treatment any type for making good to receive new roof treatment any type. and removal of same from site to out side of MOD land complete all as specified and directed.

M&L screed bed or bedding layer of 15mm thick in CM 1:6 for laying floor finishes in roof, finished even & smooth without using extra cement complete all as specified & as directed.

M&L painted cement plastered surfaces with one coat of cold applied bituminous primer @ 0.40 ltr/Sqm conforming to IS-3384 and laying APP based polymeric membrane not less than 3mm thick, weighing not less than 3.5kg/sqm, reinforced with polyester non woven fabric (weighing not less than 150gms/sqm) shall only be used. It shall be laid by torch application. Side over laps shall be 75mm and the end lap shall be 100mm and all over laps and joints shall be sealed by torch application. For parapets, membrane shall be taken to a height of minimum 60cm and then inserted inside the parapet groove. This shall be finished by a membrane flashing.

M&L preparation of APP based polymeric surface and applying two coat of aluminium paint all as specified & as directed.

M & L cutting out cracks to V section in existing roofs or terracing, cleaning out, wetting, grouting with cement and sand slurry 1:3 complete all as secified and as directed

Demolition of reinforcement concrete on roofs, floor ( other than ground floor) beams, staicase, landing , chajja and similar suspended work

M&L padding in PCC 1:2:4 type B-0 ( using 12.5mm size graded stone aggregate) laid to provide a finished slope of 1:30 finished even and smooth without using extra cement all as specified

M&L plain cement concrete type B-1, 1:2:4 (20mm graded agg) in roof kerbs or mud stops, rounded or chamfered on edges

M&L cutting groove in brick wall/ stone masonry , 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3

Dismantling of wall and ceiling board (Fibre, pulp, insulation, etc) or insulation, any thickness, including cover fillets

S&F anodised aluminium snap grid frame work for false ceiling all as specified

S&F hanger 6mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long complete all as specified

M&L 12mm thick perforated particle board/ tiles for insulation and accoustic purposes, 60cm x 60cm in size, fixed with nails to timber frame work or with staples on snap grid

M&L for cleaning and removing all scale and dirt, etc, from 500 ltr capacity tanks and from mouths of circulating pipes, etc

All as per item No 114 above but 1000 ltrs capacity

Dismantling floor , hearth or wall tiling including cement mortar bedding (but not backing) , removing serviceable tiles to store and rubbish off the premises

M & L glazed coloured ceramic tiles 300x200x7 mm thick, on vertical surfaces of wall such as dado, skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles over and including 10mm thick screed bed in CM 1:4 complete.

M&L for glazed ceramic coloured tiles in vertical surface 350 x 250 x 7mm / 450 x 350 x 7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 10mm thick rendering on stone masonary surface or surface other than fair faces of brick work in CM 1:4

M&L for non skid cermic coloured tiles 7 to 8mm thick joint free (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match & including 15mm thick screed bed in CM 1:6

All as per item No 120 above but as in skirting/ vertical surface over & incl10mm thick rendering on stone masonary surface or surface other than fair faces of brick work in CM 1:4

M & L coloured non skid ceramic tiles 300x300x7mm thick in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles over & incl 15mm thick screed bed in CM 1:6 complete.

S&F light shade vetrified ceramic tiles edge cut 10mm thick ( square/ rectangular ) polished, area of each tiles not exceeding 0.36sqm in floor etc set and jointed in neat cement slurry and pointed in white or colour cement to match over & including 15mm thick screed bed in CM (1:4) finished fair and even

All as per item No 123 above but as in skirting/ vertical surface over & incl 10mm thick rendering on stone masonary surface or surface other than fair faces of brick work in CM 1:4

S&F Non skid ceramic tiles 7 to 8mm thick area pf each tiles exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 15mm thick screed bed in CM (1:4) finished fair and even

All as per item No 125 above but as in skirting/ vertical surface over & incl 15mm thick rendering on stone masonary surface or surface other than fair faces of brick work in CM 1:4

S&F in repair 25mm wide aluminium door cill fixed to door bottom with screws/ nails complete all as specified

S&F in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket, guard and railing 60cm long complete

Dismantling of stone slabs on roofs, suspended floors, chajjas, landing etc any thickness jointed in any mortar

M&L granite 16 to 18mm thick ( of any type) work ( table rubbed and polished in steps, jambs, pillars, windows cills, cooking platforms and like in CM (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite

M&L machine cut makrana white marble slab 16 to 18mm thick in risers & treads of steps, jambs, pillars, window cills, cooking platform and similar work over & including 20mm thick screed bed ( bedding layer) in CM 1:6, pointing in white cement incluidng cutting and polishing all as specified

S&F door closer hydraulically regulated, designation No 3 universal type, suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 kg fixed in repair

S&F CP wall mixer Telephonic shower arrangement with connecting legs wall flanges and Telephonic shower crutch ( Model Make - JAQUAR Cat Part No CON -267KN or equivalent) and telephonic hand shower single flow with self cleaning and flexible tube with hook 15mm bore for mixing hot & cold water screwed down for iron

Dismantling of PVC/ AC and cast iron drain pipes 100mm dia, jointed in cement mortar and taking out of trenches if required.

S&F UPVC (SWR) pipe single socketed, any in length with rubber ring joints laid in trenches or in floors type 'B' ISI marked of 110mm bore

S&F UPVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls, type type 'B' ISI marked of 110mm bore

S & F Cast iron soil, waste and vent pipes, in any length with or without ears with cement joints, laid in trenches or in floors,100mm bore sand cast pipe

S & F Cast iron soil, waste and vent pipes, in any length with or without ears with cement joints, fix to wall,100mm bore sand cast pipe

Dismantling of PVC/ AC and cast iron drain pipes 75mm dia, jointed in cement mortar and taking out of trenches if required.

S&F UPVC (SWR) pipe single socketed, any in length with rubber ring joints laid in trenches or in floors type 'B' ISI marked of 75mm bore

S&F UPVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls, type type 'B' ISI marked of 75mm bore

S & F Cast iron soil, waste and vent pipes, in any length with or without ears with cement joints, laid in trenches or in floors, 75mm bore sand cast pipe

S & F Cast iron soil, waste and vent pipes, in any length with or without ears with cement joints, fix to wall, 75mm bore sand cast pipe

S & F in repair Cast Iron soil cowl 100 mm dia

S & F in repair Cast Iron bends (any radius) 100 mm dia with oval access doors

S & F in repair Cast Iron bends (any radius) 75 mm dia with oval access doors

S & F in repair 100mm bore cast iron branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches with oval access door complete

S & F in repair Stack clamps out of 25mm by 3mm flat iron and 8mm dia round iron stays including bolts and nuts and securing ends of stays to wall or roof for 100 mm bore pipe

S & F in repair Stack clamps out of 25mm by 3mm flat iron and 8mm dia round iron stays including bolts and nuts and securing ends of stays to wall or roof for 75 mm bore pipe

S&F UPVC (SWR) bends of any radius 110mm bore

S&F UPVC (SWR) bends of any radius 75mm bore

S&F UPVC (SWR) junction single (single T) equal or unequal 110mm

S&F UPVC (SWR) vent cowl 110mm

S&F in repair china ware valve less syphonic action type low level flushing cistern coloured with inlet ball valve float and handle incl bracket 10 ltr capacity

M&L for welding of Box type steel windows existing damage / broken hinges, handle, frame and any other parts to achieve smooth function complete (Note : 1. Skilled labour (welder) and welding items like hinges, handle, peg set etc also includes in the rate 2. wire mesh will measure and paid separatly)

Taking down chowkats or frames with shutters not exc 1.50 sqm each (without taking off shutters from the frames).

Taking down chowkats or frames with shutters exc 1.50 sqm but n exc 4.00 sqm each (without taking off shutters from the frames).

Taking down shutters of any description not exc 1 sq.m

Taking down shutters of any description exc 1 sq.m and n not exc 2.00 each

Taking down shutters of any description not exc 1 sq.m each and refixing in the same opening after easing and adjusting as required

Taking down shutters of any description exc 1 sq.m and n not exc 2.00 each and refixing in the same opening after easing and adjusting as required

S & F framed work as in doors or gates of angle or other section as chowkhat or shutters, tie bar, hold fast, guard bars, brackets etc and fixing complete Fe 290 (Gde-E-165)

Cutting holes in stone walls built in cement mortar or in cement and lime mortar exc half brick deep (depth of embeded portion of hold fasts or lugs or similar item measured from the face of the wall) for inserting hold fasts for brackets, lugs or similar articles and making good to dismantled portion in CM 1:3 and or PCC 1:2:4 complete all as specified and directed.

S & F 35mm thick factory made plain, framed, paneled door shutters kiln seasoned and chemically pressure treated second class, hardwood (two panels) with lock rail and panel of 9mm thick BWP commercial marine grade ply wood bonded with high quality liquid phenol formal dehyde sy resin adhesive confirming to IS-710. The size of rails & style shall be as per IS-1003.

S & F 35mm thick factory made second class hardwood glazed and skelton door shutter kiln seasoned and chemically treated, open rebated and prepared to receive glass/ gauge etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc complete. The size of members of shutters shall be as specified in MES SSR Part-I.

S & F framed work as in grills, gratings etc with ends of bars shouldered and/ or riveted or forged into spikes, framed guard bars, barred iron doors ladders, framed balusters, walk ways etc and fixing complete Fe 290 (Gde-E-165)

S & F butt hinges of size 100mm medium weight cold rolled mild steel and fixed

S&F Mild steel barrel tower bolts,stove enamelled black, with bright bolts 150mm and fixed.

S&F mild steel pressed handles, oval type, stove enamelled black 150mm

S&F mild steel sliding door bolts, plate type, stove enamelled black with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate 300mm length of bolt and fixed

S & F mild steel 150mm ordinary rat tail rod pattern springs including roller and roller plate complete

S&F galvanised mil steel wire cloth 0.50mm nominal dia of wire and average width of aperature 1.00 mm and fixed with tinned tacks or galvanised wire staples all as specified

S & F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube of 1.25 mm thickness suppling & fixing in opening as per specification & drawing

S&F factory made solid panel pvc door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F aluminium anodised powder coated frame for doors, window, ventilators with one or more rebates including joining cleats for fixing etc complete all as specified

S&F aluminium anodised powder coated frame for sliding window two/ three and four track shutter including top. bottom and sides track fixed type with aluminium section medium wieght including necessary joining cleats, glazing clips, stainless steel screws, complete all as specified

S&F aluminium anodised powder coated door/ window & ventilators shutter openable/ sliding type fixed with al sec weighing 0.0.55 Kg/ mtr incl necessary joining cleats, glazing clips, rubber packing snap beading, screws , handle & tower bolts, roller, incl section of handle, inter lock, top & bottom of shutter complete all as specified

S&F 4.8mm thick glass of colour/ tinted pattern in square as required & directed by Engr -in- Charge

S&F 4mm thick figured glass, pin headed type and glazing with rubber packing, beading in square n exc 0.5 Sqm in each pane all as specified

S & F 75mm size hasp and staple, safety type, aluminium anodised and fixed with screws

S & F continuous (piano) hinges, mild steel, bright finish or electrogalvinsed fixed to angle iron frame complete, width of flaps (when open) 40mm.

S & F factory made steel ventilator with top hung shutter including hinges, steel peg stay and handle complete all as specified

S & F factory made steel window with side hung shutters factory made including box type hinges with steel handle and steel peg stay complete without glazing bars devetailed or welded incl inserting the hold fast in stone masonry and make good the disturbed masonary

S & F factory made steel window with side hung shutters including box type hinges with steel handle and steel peg stay complete without glazing bars all as specified

S & F 3 mm thick figured glass pin head type and glazing with oil putty in sqaures not exc 0.5 sqm in each pane.

S & F 3 mm thick plain sheet glass ordinary quality and glazing with oil putty in sqaures not exc 0.5 sqm in each pane.

S & F galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks, or galvanised wire staples

Demolition stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in cement mortar

Demolition of cement concrete in ground floors and pavings not exc 15cm thickness (below or above ground level)

M & L plain Cement Concrete 1:4:8 type D-2 (40mm graded aggregate) in sub base of floors

M & L Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 Grade, with grey cement laid over and including 25mm thick sand cushion layer complete

M&L rubber moulded chequered cement concrete tiles bullnosed with 30mm thickness of any size set, jointed and pointed in neat cement slurry all as specified

M & L precast PCC blocks or slabs 150 mm thick (1:2:4) mix type B-1 using 20 mm graded aggregated with plain or interlocking joints as directed complete in walls setting in CM (1:6).

M&L plain cement concrete 1:3:6 type C-1 (using 20mm graded stone aggregates) as in plinth protections 75 mm thick finished even and fair with joints 10 mm wide and in full depth at corners and @ 3m c/c filled with mastic mortar

Renewing coloured non skid ceramic tiles in patches area not exc 5 Sqm including removing and cleaningv old tiles, preparing beds and laying or setting, jointing and pointing new or old tiles completed

All as per item no. 195 above but chequered cement concrete tiles complete all as directed.

M&L for taking down aluminium window/ doors ( sliding, openable) and refixing the same in opening after repair/ replacement of broken hinges, glass, hange, pivot, floor spring, beading etc all as specified

Ravi Enterprises

J.J.ENGINEERING

M/S ROHIT CONSTRUCTION

Lakshmi Enterprises

S.R.Enterprises

M/S Mohan Lal Gupta