Providing Functional Households Tap Connection (FHTC) to left out households under Providing Multi Village piped water supply scheme for Chintpurni Constituency in Amb Block, Distt. Una (HP)

Amount

Excavation in foundations and trenches in all lifts and in all kinds of soils such as pick work, jumper work, blasting in soft/hard rock, chiseling/wedging out of rock (where blasting is prohibited)and saturated soils, stacking the excavated earth within all leads and lifts, clear from the edge of excavation and then returning the stacked soil in 15 cm layers when required into plinths, sides of foundation and trenches etc., consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth as directed by Engineer-in-charge within all leads and lifts

Providing and laying cement concrete 1:6:12 (1cement : 6 sand : 12 graddedstone aggregate.40mm nominal size) and curing complete excluding cost of form work in foundation and plinth including carriage of material within all leads and lifts.

Providing form work with steel plates 3.15mm thick welded with angle iron in frame 30x30x5mm, so as to give a fair finish including centring, shuttering , strutting and propping etc. with wooden battens and ballies height of propping and centering below supporting floor to ceiling not exceeding 4meters and removal of the same for insitu reinforced concrete and plain within all leads and lifts i) In foundation, footings, bases of columns etc. and mass concrete.

ii)Columns,pillars, posts & struts,square rectangular or polygonal in plan and mass concrete.

iii)Sides and soffits of beams, beam haunchings,cantiliver bressumers and lintels not exceeding 1 Metre in depth in all heights from floor.

iv)Flat surfaces such as soffits of suspended floors, roofs landing and the like: Floors etc. upto 200mm in thickeness.

v) Vertical surfaces such as Walls (any thickness but not less than 0.1 mtr. Thickness) includingattached pillasters,buttresses,plinth & string courses etc. From top of foundation level up to all floor levels in all leads and lifts the entrire satifaction of the Engi

vi)Stair case with sloping or stepped soffits including riser and stringers excluding landing.

Providing and laying reinforced cement concrete work 1:1.5:3 (1cement : 1.5 approved sand : 3 approved quarry stone aggregate.20mm nominal size) and curing complete excluding cost of form work and reinforcement for reinforced cement concrete work including carriage of material within all leads and lifts. i)Foundation footings basis of columns and the like and mass concrete .

ii) walls (any thickness but not less than 0.1 mtr. Thickness)including attached pillasters,buttresses,plinth & string courses etc. From top of foundation level up to all floor levels in all leads and lifts the entrire satifaction of the Engineer-in-Charge

iii)Columns,pillars, posts & struts etc upto floor two level. Ground Floor

iv)Columns,pillers, posts & struts etc upto floor two level. First floor Plan

v) Lintels beams, girders,bressumers and cantilevers upto floor two level etc. Ground Floor

vi)Lintels beams, girders,bressumers and cantilevers upto floor two level etcFirst floor Plan

Suspended floor roofs, landing and shelves and their supports balconies, beams, girders,bressumers and cantilevers upto floor two level. i) for Ground Floor

ii) for First floor Plan

Stair cases ( except spril stair cases ) excluding landing but including preparing of the surface and finishing of nosing upto floor two level.

Providing tor steel reinforcement for RCC work including bending binding and placing in position complete upto floor two level. Tor steel.

1st Class Brick work using common burnt clay building bricks in super structure in cement mortar 1:6 (1cement :6 sand) including carriage of materials within all leads and lifts. i) for Ground Floor

ii) for First floor Plan

Half brick masonry in common burnt clay building bricks in cement mortar 1:4 ( 1cement : 4 sand) including carriage of all material within all leads and lifts above floor two leve .i) for Ground Floor

ii) for First floor Plan

Providing 2nd class deodar wood work in frames of doors, windows, clerestory, windows and other frames wrought, framed and fixed in position complete in all respect i/c all leads and lifts and as per the direction of the Engineer-in-charge

15mm thick cement plaster with cement mortar 1:6(1 cement:6 sand) in single coat on fair side of brick/concrete/stone walls for interior plastering upto all heights including arises, internal rounded angles chamfers and/ or rounded angles not exceeding 80 mm in all girth and finished even and smooth i) Upto floor two level

20 mm thick cement plaster with cement mortar 1:6(1 cement; 6 sand) in single coat on rough side of brick/concrete/stone walls for interior plastering upto all heights including arises, internal rounded angles chamfers and/ or rounded angles not exceeding 80 mmin all girth and finished even and smooth i) Upto floor two level

6 mm thick cement plaster to ceiling in C.M.1:3 (1Cement,3 sand) with in all leads and lifts complete in all respect.

15 mm thick cement plaster in single coat on fiar side of brick/concrete/stone walls for interior plastering up to floor two level including arrisses,internal rounded angles,chamfers and /or rounded angles not exceeding 80 mm in girth and finished even and smooth with in all leads and lifts in C.M 1:3 ( 1 cement,3 sand ) with all leads and lift.

Filling in plinth with sand under floors including watering, ramming consolidating and dressing complete. within all leads and lifts as per the direction of Engineer-In-Charge.

Boulder filling under floor with hard stone, with at least one broken face, hand packed properly within all leads and lifts complete as per the direction of Engineer-In-Charge.

White glazed tiles 6mm thick in flooring, treads of steps and landing laid on bed of 12 mm thick cement mortar 1:3( 1 cement :3 sand) finished with flush pointing in white cement.

White glazed tiles 6mm thick (NITCO MAKE) in skirting risers of steps and dedo 12 mm thick cement mortar 1:3( 1 cement :3 sand) and joited with cement slurry.

Providing and fixing 2nd class deodar wood 40mm thick panelled and glazed or panelled and glazed shutters for doors,windows & clerestory windows. including black enamelled iron butt hinges with necessary screws.

P/F M S Grills of required pattrens in wooden frames of windows etc. with M.S. flats, square or round bars with round headed bolts and nuts or by screws. complete as per the direction Engineer-in-charge .

Providing under layer for plinth protection of 75mm thick (unconsolidated) bed of dry brick/stone aggregate 40mm nominal size well rammed and consolidated and grouted with fine sand including preparation of ground.

Providing plinth protection 50mm (fifty millimeters )thick in cement concrete 1:3:6 ( one cement; three sand; six graded stone aggregate 20mm(twenty millimeters) nominal size) including finishing the top surface of concrete.

Providing and fixing anodized aluminum sliding doors bolts anedized colour and shade with bolts and nutts, screw, etc complete as per the direction of Engineer-In-Charge i) 300x16mm (Three hundred into sixteen millimeters) nominal size.

Providing and fixing aluminium tower bolts (Barrel type) anodized transparent or dyed to required shade and colour with screws etc complete as per the direction of Engineer-In-Charge i)250x10mm (Two hundred fifty into ten millimeters) nominal size

ii)150x10mm (One hundred fifty into ten millimeters) nominal size

Providing and fixing aluminium handles anodized transparent or dyed to required colour and shade with necessary screws etc. complete as per the direction of Engineer-In-Charge i)125mm (one hundred twenty five millimeters) nominal size

ii)100mm (one hundred millimeters) nominal size

Providing and fixing 100 mm bright finished brass floor door stopper with rubber cushion screws etc to suit shutter thickness complete

Providing and fixing M.S. brass finishe hand drawn hooks and eyes 200mm. Complete within all leads and lifts as per the direction of Engineer-in-Charge

Providing and fixing hudraulic door closer of approved brand and manufacture ) completemass respect as per the direction of Engineer-In-Charge

Providing and fixing wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge designation 85 G. with wire of dia 0.56 mm for doors windows and clerestorey windows including bright finished black enamelled iron hinges with necessary screws.

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose material and other foreign matters sand papered smooth to give final matter finish to the surface complete.

Applying one coat of Acrylic primer( Spectrum or equivalent of Superior quality) on new concrete/masonry/ plastred surfaces after and including preparing the surface by thoroughly brushing the surface free from mortar droppings, and other foreign matters sand papered the surface smooth smooth to give final matter finish to the surface complete.

Distempering (Two coats) with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated wall surface to given an even shade over and including primer coat of whiting after thoroughly brushing the surface free from mortar droppings and other foreign matter including preparing the surface even and sand papered smooth.

Providing/Laying granite stone inflooring 20mm average thickness base of cement mortar 1:3 (1 cement : 3 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of granite stone including rubbing and polishing complete 20mm thick.

Providing and fixing stainless steel railing (1.00 mtr. height)a fixed in straight length over stainless steel flat/round at top of vertical & horizontal balusters including fixing with steel screws complete as per the direction of Engineer-in Charge.

Providing and fixing 12 mm thick and 100 mm wide pelmet with 25 mm diameter curtain rod and brackets including fixing with 25x3 mm M.S. flat 10 centimeter long and plugs etc. complete in 1st class deodar wood within all leads and lifts as per the direction of Engineer-in- Charge.

Providing in RCC work smooth finishing of the exposed surface with cement mortar 1:3 (one cement: three sand) to give smooth and even surface i/c the cost of form work & curing complete upto floor two level.

Providing and fixing on wall face PVC (D-Plast) rain water pipes of working pressures not less than 4.5 kg/Sqm i/c filling the joints with approved adhesive complete. (100mm dai pipes)

Providing and fixing on wall face PVC (D-Plast) accessories for rain water pipes including filling the joints with approved adhesive complete .i)PVC plain bend 100mm dia

Providing and fixing M.S. holder bats clamps of approved design of CI or SCI pipes embedded in and including cement concrete blocks 10x10x10cm of 1:2:4 mix ( 1 cement : 2 sand : 4 graded stone aggregates 20mm nominal size) and cost of cutting holes and making good the wall etc. 100 mm dia for PVC pipe.

Providing and laying cement concrete 1:3:6 ( 1 cement,3 sand,6 graded stone aggregate 40 mm nominal size )and curing complete excluding cost of form work in foundation and plinth with in all leads and lifts complete in all respect.

Providing and laying cement concrete 1:1.5:3 ( 1 cement,1.5 sand,3 graded stone aggregate 20 mm nominal size )and curing complete excluding cost of form work and reinforcement for rainforced concrete worl in i)Suspended floors, roofs, landings and shelves and their supports, balconies, beams ,girders bressumers and cantilevers upto all floor level.

Providing and fixing 200mm wide CI Rungs with chequarred/ Ribbed non slip surfaces i/c fixing in M/hole with 200X100X100mm cement conc. 1:3:6(1 cement:3 Sand:6 Stone aggregate 40mm nominal size) in all leads and lifts the satisfation of the Engineer-in Charge.

Providing & fixing CI man hole cover with frame for man holes for frame of internal dimension 455X610mm (Light duty single seat pattern-I) the weight of cover should not be less than 58 Kg. Including carriage of material within all leads & lifts.

Providing and Fixing vent pipe including cowl with mesh in the top of the tank including all lead and lifts.

Providing & laying cement concrete 1:5:10 (1 Cement: 5 Sand:10 Graded stone aggregate 40mm nominal size) with 15% plum and curing complete excluding cost of form work in R/wall, B/ wall, the size of plums shall usually be 150mm to 300mm as per HPPWD specification within all leads and lifts.

1st. Brick work using common burnt clay building bricks in foundation and plinth in Cement mortar 1:4 (One cement: Four sand) within all leads & lifts.

Providing & laying cement concrete 1:2:4 (1 Cement: 2 Sand:4 Graded stone aggregate 20mm nominal size) and curing complete excluding cost of form work in Top of wall with floating coat of neat cement (40mm thick) in allleads and lifts as per the direction of the Engineer-in-Charge.

Pointing on brick work with cement mortor 1:3 (! cement:3 sand) in all leads and lifts as per the direction of the Engineer-in-Charge. Ruled Poining.

Excavation in earth work and filling in 15cm layers in foundations and plinths including ramming, watering and consolidating complete in all respect including carriage of materials within all leads and lifts and as per the direction of the Engineer-in-charge.

Finishing wall with water proofing cement paint of approved brand & manufacture & of required shade on undecorated wall surfaces (two coats) to give an even shade after thotoughly brushing the surface to remove all dirt & remains of loose powdered materials.

Steel work welded in built up section,trusses & frames work i/c cutting hoisting,fixing in position & applying a priming coat of red lead paint :- in grating,framed guard, bars, ladders, railng, bracket & similar work. complete in all respect.

Painting two coats(excluding priming coat) on new steel and other metal surface under coat ready mixed with enamel paint brushing to give an even shade including cleaning the surface of all dirt dust and other foreign matter with ready mixed paint other than white in all leads and lifts.

Providing and supplying Seven seater sofa set with centre Table including all lead and lifts as per the Direction of Engineering-in-charge.

Providing and supplying S.S three seater Sofa chair including all lead and lifts as per the Direction of Engineering-in-charge.

Providing and supplying Revolving chair including all lead and lifts as per the Direction of Engineer-in-charge.

Providing and Fixing Double bed with side Table including all lead and lifts as per the Direction of Engineer-in-charge.

Providing and Fixing Double bed with side table including all lead and lifts as per the Direction of Engineer-in-charge.(VIP set)

Providing and Fixing dinning Table with 8 Seats wooden chair including all lead and lifts as per the Direction of Engineer-in-charge.

Providing and Fixing wooden Almirah 6.5X3.5 as per the Direction of Engineer-in-charge.

Providing and fixing high pressure PVC spigot and socket soil waste and ventilating pipes ISI marked including fixing with approved adhesive etc .i) 75mm nominal size

ii) 110mm dia nominal size.

Providing and fixing 75mm PVC floor trap ISI marked of self cleaning design complete in all respect as per the direction of engineer in charge .

Providing and fixing PVC Plain bend ISI Marke including fixing with approved adhesive etc. i) 75mm nominal size

ii) 110mm nominal size

Providing and fixing PVC bends of reqired degree with oval access door insertion rubber washer 3mm thick bolts and nuts complete including fixing with approved adhesive etc .i) 75mm nominal size

ii) 110mm nominal size

Providing and fixing PVC Tee complete in all respect as per the direction of emgineer in Charge. i) 75mm nominal size

ii) 110mm nominal size

Providing and fixing PVC caps complete in all respect as per the direction of emgineer in Charge. i) 75mm nominal size

ii) 110mm nominal size

Providing and fixing Cock Brass Angle Valve 15 mm dia complete in all respect as per the direction of emgineer in Charge.

Providing and fixing Brass Bib Tap Long Nose (Superior or heavy type) 15 mm dia complete in all respect as per the direction of emgineer in Charge.

Providing and fixing Brass Bib Tap Short Nose (Superior or heavy type)15 mm dia complete in all respect as per the direction of emgineer in Charge.

Providing and fixing C.P Brass Pillar Tap ( Superior or Heavy type) 15 mm dia complete in all respect as per the direction of Engineer in Charge.

Providing and fixing C.P Brass Shower 100 mm dia complete in all respect as per the direction of Engineer in Charge.

Providing and fixing C.P. Brass Soap dish with C.P. brass brackets fixed to wooden cleats with C.P. brass screws complete in all respect as per the direction of emgineer in Charge.

Providing and fixing C.P. Towel Ring complete in all respect as per the direction of Engineer in Charge.

Providing and fixing C.P. Brass Towel Rail complete with C.P. brass brackets fixed to wooden Plugscleats with C.P. brass screws i.e size 600x20 mm as per the direction of emgineer in Charge.

Providing and fixing vitreous china wash basin with single hole for pillar tap with C.I. or MS brackets painted white i/c cutting holes & making good the same but excluding fitting flat backi.e size 630x450 mm as per the direction of engineer in charge.

Providing and fixing china pedestal for wash basin complete recessed at rhe black for the reception of pipes and fittings of Parryware / Hindware/ CERA make as per the direction of engineer in charge. .

P/F Brass waste Coupling 32 mm wash basin, water closet & sink complete in all respect as per the direction of engineer in charge.

P/F Brass lead waste Pipe 32 mm for wash basin or sink including checknet complete in all respect as per the direction of engineer in charge.

P/F Brass Double waste Pipe 32 mm wash basin or sink including checknet complete in all respect as per the direction of engineer in charge.

P/F Tooth Brush and tumbler holder viterious channel complete in all respect as per the direction of engineer in charge.

P/F 600X450 mm bevelled edge mirror of superior glass mounted on 6 mm thick AC sheet or Ply wood sheet & fixed to wooden plug with CP brass screws & washers as per the direction of engineer in charge.

P/F C.P.Brass Toilet Paper holder complete in all respect as per the direction of engineer in charge.

Providing and fixing white vitreous china wash down water closet (European type W.C.pan) with integral 'P'or 'S' trap including jointing the tap with soil pipe in CM 1:1 of Parryware / Hindware/ CERA,( seat and cover to be measured and paid for seperately) as per the direction of engineer in charge. i)Anglo Indian Universal Closet

Providing and fixing CP brass Jet Jaquar/Jal make with connection pipe and other fitting for (European Type) WC pan complete in all respect as per the direction of engineer in charge.

Providing and fixing single hole Sink Mixture complete in all respect as per the direction of engineer in charge.

Providing and fixing 10 liters vitreous china low level flushing cistern with a pair of C.I. or mild steel brackets complete with fitting such as lead valve less sower 15 mm nominal size ball valve with polythene float C.P brass handle, unions and couplings for connecting with inlet, outlet and overflow pipes 40mm dia. C.P flush bend including cutting holes in walls and making good the same and connecting the flush bend pipe with cistern and closet ( over flow pipe to be measured and paid for separately ) 10.00 liters. of Parryware / Hindware/ CERA

Providing and fixing C.P. brass grating complete in all respect as per the direction of engineer in charge.

Providing and fixing PVC connection pipe with brass unions i.e 40 cms inlet & PVC connection i/c making the wall good to wall ceiling complete in all respect as per the direction of engineer in charge.

Providing and fixing PVC connection pipe with brass unions i.e 60 cms inlet & PVC connection i/c making the wall good to wall ceiling complete in all respect as per the direction of engineer in charge.

P/F kitchen stainless steel sink with CI or MS brackets painted white including cutting holes in walls and making good the same but excluding fittings of stainless sink with drain board super deluxe No. 632 of size 161x54 cm of diamond or its equivalent make.

Providing and fixing plasic seat(solid/Hollow type) and cover for wash down water closet with C.P. brass and hinges and rubber buffers solid type White plastic seat of Parryware / Hindware/ CERA.

P/F Gate Valve 15 mm dia complete in all respect as per the direction of engineer in charge.

P/F Conceled stop cock 15 mm Dia complete in all respect as per the direction of engineer in charge.

Providing and Fixing 1000 Liters cap Sintex water Storage tank double Layer with top lid and making connections complete in all respect as per the direction of Engineer- in -Charge.

VARINDER KUMAR

Ajay Kumar Bassi

Naveen Kumar