REPAIRS MAINT OF FLOORING ROOF SHEETS JOINERY FALSE CEILING PLUMBING AND OTHER CONNECTED WORKS OF OFFRS INSTITUTE MESSES IB AND OTHER CENTRAL AMENITIES AT OLD CANTT UNDER GE GANGTOK

Amount

Dismantling Wrought Iron or Mild Steel Work, viz. Mild Steel Flat Iron (Wind Tie) and Similar Work including Mild Steel Bolts, Nuts, etc., complete all as specified and as directed.

Taking down chowkats with shutter of any description (without taking down shutter from the frame) exc. 1.5 Sqm and n.exc 4.00 Sqm and removing from site complete all as specified and as directed.

Taking down chowkats with shutter of any description (without taking down shutter from the frame) n.exc 1.5 Sqm each and removing from site complete all as specified and as directed.

Taking down shutters of any description exc 1 Sqm but n.exc 2 Sqm each and removal from site complete all as specified and as directed.

Distmantling of floor, hearth or wall tiling including cement mortar bedding (but not backing) and removal of dismantled materials/rubbish from site complete all as specified and as directed

Taking down cement plaster/terrazo cast in situ of any description on brick or stone walls, including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed.

Demolition to cement concrete in ground floors and pavings n.exc 15cm thickness (below or above ground level) complete all as specified and as directed.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for and removal of rubbish of the site complete all as specified and as directed. (reinforcement cut as required to facilitate demolition).

Demolition of precast concrete block walling built in cement mortar complete all as specified and as directed.

Dismantling old PGI/CGI sheeting any gauge, thickness including Nainital. Sikkim or similar pattern roof/facia including ridge etc and keeping serviceable sheets in safe custody for re-use complete all as specified and as directed.

Hacking out old broken glass any thickness, size, quality or description, from metal/wooden frame including punching or drilling out old glazing pins and removal of demolished material from site complete all as specified and as directed.

M&L Second Class Hardwood Plain, Solid, Straight Chowkats and Frames, Wrought, Framed rebated on the Solid, Rounded or Chamfered, put together with Glue, Pinned at Joints complete all as specified and as directed.

M&L for 35mm thick 2nd class HW plain, framed, paneled shutters (two panel) with lock rail and panel of 9mm thick BWR commerical ply or 12mm veneered particle board with commercial face veneering on both faces. The size of rail & site as per IS : 1003 (Part-I), Kiln, seasoned & chemically pressure, treated complete all as specified and as directed.

M&L for 30mm thick 2nd class hard wood well seasoned glazed and skeleton shutters, open rebated and prepared to receive glass gauze etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc size of members of shutters as specified in SSR Part-I, section 8, clause 8.24 (a) complete all as specified and as directed.

S&F 30mm thick flush door shutter, solid core construction, with block board core and plywood face panels. Commercial type on one side and other face coverd with decorative face veneer with 6mm thick teak wood lipping/frame to match complete all as specified and as directed.

Taking down Shutter of any description exc. 1.0 Square Metre and not exc. 2.0 Square Metre Each and refixing in the same opening, complete all as specified and as directed.

M&L for plain cement concrete 1:3:6 type C1 (using 20mm graded stone aggregate) as in coping including necessary formwork complete all as specified and as directed.

S&F 250mm aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts or extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed.

S&F 150mm long aluminium anodised handles, cast type, complete all as specified and as directed.

S&F for 100mm size mild steel pressed handles, oval type, stove enamelled black complete all as specified and as directed.

S&F 150mm long aluminium anodised tower bolts of extruded section and fixed complete all as specified and as directed.

S&F 100mm long aluminium anodised tower bolts of extruded section and fixed complete all as specified and as directed.

S&F 100mm long electrolated butt hinges, medium weight, cold rolled, mild steel complete all as specified and as directed.

S&F 100mm size brass handles (decorative type) cast type polished bright complete all as specified and as directed.

S&F continous (piano) hinges, 30mm width of flap(when open), mild steel, bright finish or electro galvanised fixed with stainless steel screws complete all as specified and as directed.

S&F mild steel flat iron bent to shape, holes, drilled etc complete as in wind ties or as in hold fast, clamps, supports for rainwater, venilating pipes, including bolts, if required, hooks (stay) etc and similar small articles conforming to Fe-290 Gde E-165 including one coat of red oxide primer complete all as specified and as directed.

M&L for plain cement concrete 1:3:6 type C2(using 20mm graded stone aggregate) as in fixing of hold fast, bed blocks etc including necessary formwork as required complete all as specified and as directed.

S&F of factory made steel windows with side hung shutters openable type including projective type hinges, steel handle and peg stay complete with glazing bars fixed in existing opening to match as per existing surface including a soft coat of primer including taking down old /unserviceable window complete all as specified and as directed.

S&F of factory made steel ventilator with top hung shutter including hinges, steel peg stay including a shoap coat of primer including taking down old/unserviceable ventilator complete all as specified and as directed.

S&F of factory made solid PVC door frame of size 50mmx47mm made out of 5mm thick single side prelaminated PVC sheet reinforced with mild steel square tube and edges will be painted to match with single side prelaminated sheet as per specification and drawing egiven on MES schedule Part-II (2010), Page No. 160 complete all as specified and as directed.

S&F 75mm long electrolated butt hinges, medium weight, cold rolled, mild steel complete all as specified and as directed.

S&F of 30mm thick (style thickness) factory made solid panel PVC door shutter consisting of frame made out of mild steel tubes for top and bottom rails, solid steel frame shall be covered with heat moulded single side prelam PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and single side prelam PVC sheet for top rail, lock rail and bottom rail on either side & as gap insert for top rail and bottom rail, panelling of both side prelam PVC sheet to be fitted in the mild steel frame welded/sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent cement as per specification and drawing given on MES schedule part-II (2010), Page No. 156 complete all as specified and as directed.

S&F in repair 18/19 mm thick particle board, medium density flat pressed, single layer type with BWR type adhesive fixed with screws to timber frame work or in pelmets as in repairs including teak wood lipping of 6mm thick all round fixed with nails complete all as specified and as directed.

S&F 15mm bore dia angular stop cocks, fancy type, chromium plated, with wall flange screwed down, screwed from iron pipe or union and complete all as specified and as directed. Make : ESSCO Code-TQT 513A or equivalent make as approved.

Taking up or down 15mm bore steel water tubings including fittings etc complete and making good disturbed surfaces of walls/ ceilings etc complete all as directed.

Taking up or down 20mm bore steel water tubings including fittings etc complete and making good disturbed surfaces of walls/ ceiling etc complete all as specified and as directed.

Supply and fix galvanised steel water tubing 15mm bore medium grade with all fittings and fixed complete to walls/ceiling or laid in floors complete all as specified and as directed.

Supply and fix galvanised steel water tubing 20mm bore medium grade with all fittings and fixed complete to walls/ceiling or laid in floors complete all as specified and as directed.

Fixing only galvanised steel water tubing 15mm bore, medium grade with all fittings and fixed complete to walls/ceiling or laid in floors complete all as specified and as directed.

Fixing only galvanised steel water tubing 20mm bore, medium grade with all fittings and fixed complete to walls/ceiling or laid in floors complete all as specified and as directed.

Cutting chases for concealed water tubing pinning in, and making good to facing where required and pointing in cement mortar (1:30 and making good cutting n.exc 10cm girth in concrete block complete all as specified and as directed.

Materials & labour for coloured glazed ceramic tiles of size (300x200mm/350x250mm/450x350mm) of 7mm thick, as in vertical surfaces such as skirting/dado/riser to steps etc conforming to IS-13712 grade IB-III set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over and including cement screed bed/backing layer of 10mm thick in cement mortar (1:4) complete all as specified and as directed.

Material & labor for non skid coloured ceramic tiles of 7 to 8mm thick ( Square/rectangular) area of each tile exc 0.11 Sqm but not exc 0.18 Sqm as in floors etc conforming to IS-13712, grade B-II-(a) set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over and including cement screed bed/bedding layer of 15mm thick in cement mortar (1:6) complete all as specified and as directed.

M&L for Dark shade vitrified ceramic tiles 10mm thick (Square/Rectangular) polished, area of each tiles not exceeding 0.36 Sqm, as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed/bedding layerin cement mortar (1:6) complete all as specified and directed.

M&L for Dark shade vitrified ceramic tiles 10mm thick (Square/Rectangular) polished, area of each tiles not exceeding 0.36 Sqm, as in vertical surfaces such as skirting/dado etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick screed bed/backing laying in cement mortar 1:4 complete all as specified and directed.

M&L for 25mm thick PCC(1:2:4), type B0 (using 12.5mm graded stone aggregate) as in sub-base of floor finished rough for receiving floor finishes complete all as specified and as directed.

M&L for lacquer coated coloured chequered cement concrete tiles of size 300x300x25mm thick set, jointed and pointed in neat slurry in floors and steps with grey cement and pigments over and incl 15mm thick screed bed or bedding layer in cement mortar (1:6) complete all as specified and as directed.

M&L for 100mm thick PCC (1:3:6) type C2 (using 40mm graded stone aggregate) as in path/steps etc finished even and fair without using extra cement including necessary form work complete all as specified and as directed.

M&L Hardcore of gauge not exc. 63mm, deposited, spread and levelled in layers not exc. 15 Cm thick, watered and rammed to a True Surface, complete all as specified and as directed.

M&L for 100mm thick PCC (1:2:4), type B2 (using40mm graded stone aggregate) as in hardstanding/flooring etc finished even and fair without using extra cement including necessary form work complete all as specified and as directed.

M&L for 75mm thick PCC (1:3:6), type C-2 (using 40mm graded stone aggregate) as in plinth protection; path/hardstanding etc laid in bays/panels not exc 2.00 Sqm each includng construction points at suitable interval and each corner and filled with bituminous inastic filling(1 Part bitumen & 3 part sand) and finished the surface even and smooth without using extra cement complete all as specified and as directed.

M&L for PCC (1:3:6) type C-2 using 40mm graded stone aggregate as in surface channels and drains including forming fair finished to drain channel complete all as specified and as directed.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete using extra cement including form, moulds, mittred/stopped ends complete all as specified and as directed.

Add or deduct for each 25mm girth or part thereof over or under 30cm girth complete all as specified and as directed.

M&L for rendering 15mm thick in cement mortar (1:6) on fair face of brick or concrete surfaces finished surface even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 20mm thick in cement mortar (1:4) in two layer of 10mm thick each with using WPC shall be mixed with cement mortar in finishing outer layer only as per manufacturer's instruction, on other than fair face of brick/stone masonry (external surfaces) finished surface fair and even without using extra cement complete all as specified and as directed. Note : (WPC shall be measured and paid separately as supply only)

M&L for rendering 5mm thick in cement mortar (1:3) on fair face of concrete surfaces such as ceiling finished surface even and smooth without using extra cement complete all as specified and as directed.

Supply only Integral Water Proofing Compound, conforming to IS-2465-2003 and/or as approved, complete all as specified and as directed.

Taking down eaves gutter and rain water pipes (any size and pattern), including all fittings, heads, shoes, bends, swan necks etc including removal to stores complete all as specified and as directed.

S&F for PVC(SWR) half round 150mm bore with round edges including all accessories like bend, T etc complete all as specified and as directed.

S&F for PVC(SWR) (Bore of pipe 110mm) pipes, single socketed, in any length with rubber ring joints, fixed to wall/laid under trenches complete all as specified and as directed.

S&F for PVC(SWR) (Bore of pipe 110mm) bends any radius fixed to PVC pipes/steel gutters etc complete all as specified and as directed.

S&F for PVC(SWR) junction single (single tee) equal or unequal, dia of pipe 110mm complete all as specified and as directed.

S&F in repair 75mm bore, PVC (SWR) pipes of presure rating 4 kgf/cm2, single socketed in any length with rubber ring joints, laid in trenches or under floors including necessary earthwork, fixed on walls complete all as specified and as directed.

S&F in repairs 75mm bore PVC (SWR) bend of any radius for PvC(SWR) pipes/steel gutters etc, fixed to walls complete all as specified and as directed.

S&F 75mm bore PVC(SWR0 junction single, (Single T) equal or unequal with access door complete all as specified and as directed.

S&F PVC floor trap, Nahani trap, 100mm diameter of outlet, with gratings including jointing to waste pipe fixed in PCC 1:2:4 type B1 (using 20mm graded stone aggregate) complete all as specified and as directed.

M&L for 0.63mm thick CGI sheeting, ISI marked with 275 grams per sqm zinc coating with two corrugation side laps fixed with 'L' type or 'J' type or cranked hook bolt and washers in roof covering/walls etc complete all as specified and as directed.

S&F 0.50mm thick pre-painted galvalume aluminium zinc silicon finished with resin coat on both side @ 70 grms/Sqm GI based corrugated steel sheets of any colour and any pattern as approved having tensile strength of 550 Mpa as in roof covering fixed with self tapping screws as in roof complete all as specified and as directed.

S&F 0.50mm thick pre-painted galvalume aluminium zinc silicon finished with resin coat on both side @ 70 grms/Sqm GI based corrugated steel sheets of any colour and any pattern as approved having tensile strength of 550 Mpa as in ridges, valley, eaves etc fixed with self tapping screws complete all as specified and as directed.

S&F 3mm thick sheet glass panes, ordinary quality and glazing with oil putty including steel pin in square n.exc 0.5 Sqm in each pane fixed to steel frame complete all as specified and as directed.

M&L for applying one coat of white washing including preparation of old/previously treated surfaces of ceiling complete all as specified and as directed.

M&L for applying three coats of white washing including preparation of new/previously untreated surfaces of ceiling complete all as specified and as directed.

M&L for applying two coats of white washing including preparation of new or previously untreated surfaces of wall complete all as specified and as directed.

M&L for preparation of old decorated/plastered surfaces of walls, by brooming down or steel wire brushing, scrapping down smoke soot, mould moss and efflorescent salts and trading oil and greasy spots and applying one coat of white wash complete all as specified and as directed.

M&L for preparation of old/new plastered surfaces of walls and applying two coats of soil bound distemper over a coat of primer applied over 3mm thick super fine Birla or altek wall care putty finish including complete removal of existing treatment complete all as specified and as directed.

M&L for preparation of old plastered surfaces of walls by brooming down or steel wire brushing, scrapping down smoke soot, mass and efflorescent salts and trading oil and greasy spots and applying one coat of cement base paint complete all as specified and as directed.

M&L for preparation of old plastered surfaces of walls and applying one coat of oild bound distemper complete all as specified and as directed.

M&L for applying two coats of weather shield exterior emulsion paint over a coat of alkali resistant primer including preparation of new/old wall surface complete all as specfied and as directed.

M&L for applying one coat of weather shield exterior emulsion paint including preparation of old wall surface complete all as specified and as directed.

Supply and fix in repair vitreous china squatting pan of 'Orissa pattern' of size 580mm x440mm (white) with integral foot rest 'P' or 'S' trap, front or back inlet, any pattern(excluding flushing cistern and flush pipe) including connection to trap and flushing pipe anti syphon pipe etc complete including connection to trap, and to flushing pipe, antisyphonage pipe etc. complete including making good to floor all as specified and as directed. Make : ESSCO Cat Part No. ECS-WHT-453 or equivalent approved.

Supply and fix in repair vitreous china, white colour, flat back, wash hand basin of size 55cm x 40cm x 79 cm fixed with brackets, including providing 32mm dia PVC waste pipe, 32mm bore CP waste coupling with or without padestal and making all necessary connections complete all as specified and as directed. Make : ESSCO Cat part No. ECS-WHT-803 or equivalent approved

Supply and fix PVC connections 15mm size with PTMT/Brass nuts of length 600mm complete all as directed by the Engr-in-Charge. Make Prayag or equivalent make approved.

Supply and fix in repair 10 litre capacity low level PVC flushing cistern(white), syphonic action type, with inlet, ball valve, float, handle, fixed with cast iron bracket (of suitable size) and providing 32mm dia PVC flush pipe and making all necessary connections complete all as specified and as directed. Make : ESSCO Cat part no. WHE-WHT-183L or equivalent approved make complete all as specified and as directed.

Supply and fixed 15mm bore pillar taps, fancy type with long neck with aerator cast copper alloy with capstan head, chromium plated, screwed down, high pressure with long screwed shanks, fly-nuts, with screwed for GI pipe complete all as specified and as directed. Make : ESSCO Cat part No. SQT-508KN or equivalent/approved make complete all as specified and asi directed.

S&F in repairs GI steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and as directed.

S&F rolled section as in main and cross beams, hip and jack rafters, purlins where connected to common rafter and running rails and guides for sliding doors fixed with angle clear or other connecting plates conforing to Fe-410-W(Gde-E-250 quality-A)including one coat of red oxide zinc chrome primer after preparation of surfaces at contractor's workshop before fabrication complete all as specified and as directed.

S&F framed work such as grills, gratings, etc, with ends of bars shouldered and/or reveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe 290 Gde E-165 complete all as specified and as directed.

Dismantling of wall and ceiling hard boards/AC sheets(Fibre pulp insulation etc) or insulation board and plywood in any thickness & any position including cover fillets complete all as specified and as directed.

Dismantling timber scantling as in fillets, rails, posts, rafters, purlins etc under 40 Sqcm in section complete all as specified and as directed.

Dismantling timber scantling 40 Sqcm and over in section any position as in unframd work including separating serviceable timber and keeping in safe custody for reuse complete all as specified and as directed.

M&L for 6mm thick plywood, grade BWR, type BB, fixed with nails to timber frame work in wall/ceiling complete all as specified and as directed.

M&L for preparing wooden surfaces new or old of any description and girth and applying two coats of creosote oiling complete all as specified and as directed.

M&L for 2nd class hard wood timber scantling fixed clean swan including trating with raw linseed oil as in unframed work complete all as specified and as directed.

M&L for 2nd class hard wood plain fillets, square, rectangular or triangular in section, clean swan, secured with nails, cross sectional area exc 3 Sqcm & n.exc 6 Sqcm complete all as specified and as directed.

M&L for providing, cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) in roof kerbs or mud stops, rounded or chamfered on edges complete including necessary form work complete all as specified and as directed.

S&F 5-6 mm thick PVC ceiling/wall panels of interlocking types, width 250/255 mm with lamination design and exc 60% of PVC content including necessary H-joints, internal/external corner trim, corner cove, F/J edge trims where required fixed with hidden screws to steel/wooden frame work complete all as per manufactuer's instructions and specified and as directed.

S&F powder coated GI grid frame work for false ceiling comprising of the following sections for making partitions of 600mmx600mm size fixed to walls with rawl plugs & screws and hanged to roof with and including 1mm dia GI wire suspender of suitable length and butterfly clips, size of main tee shall be 23mmx28mmx 0.30mm thick, cross tee shall be 23mm x28mm x0.30mm thick and wall angle shall be 20mm x20mm x 0.30mm thick complete all as per manufacturer's instructions & specified and as directed.

Supply and fix 4mm thick Non asbestos fibre cement building board (E-board) of approved texture, for insulation and acoustic purpose of size 595x595mm size fixed with staples on snap grid as in ceiling with and including dusting of surfaces and applying two coats of oil emulstion distemper over a coat of primer including preparation of surfaces complete all as specified and as directed.

M&L for preparation of new or previously untreated wooden surfaces of any description n.exc 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and as directed.

M&L for applying two coats of synthetic enamel paint over a coat of red oxide primer to new or previously un-treated steel surfaces of any description over 10cm in width or girth including preparation of nw steel surfaces complete all as specified and as directed.

M&L for applying one coat of synthetic enamel paint to old or previously treated steel surfaces of any description over 10cm in width or girth including preparation of old steel surfaces complete all as specified and as directed.

M&L preparation of new or previously untreated wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and as directed.

M&L for preparation of old painted wooden surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

Supply and fixing in repair star white vitreous china wash down water closet pan (pedestal pattern) EWC, of size 520x360x390 mm with 'P' or 'S' trap, including fixing bolts, Plastic water closet seat and cover, closed pattern with flat bottom, and mild steel chromium plated or aluminised hinging device, making all necessary connections complete all as specified and as directed. Make : ESSCO Cat part No. ECS-WHT-551PS or equivalent approved make.

S&F stainless steel sink with drainage board made of stainless steel 1.0mm thick for kitchen with plug, washers, waste pipe including cantilever cast iron brackets connecting union of 40mm CP waste fitting and PVC waste pipe of required length with CP/PTMT fly nuts etc complete overall size 915mm x 460mm with bowl size 410mm x355mmx 165mm complete all as specified and as directed. (Make : Nirali Model Elegance or equivalent approved make.

S&F bib tap, long body cast copper alloy fancy type, chromium plated with crutch or butterfly handle, screwed down for 15mm bore GI pipe or for brass ferrule including taking down old unserviceable one. Make : ESSCO CAT Part No. SQT-511 KN or equivalent approved make.

S&F in repair hand shower(health faucet) 8mm dia alongwith 1m flexible tube and wall hook fixed in position complete all as specified and as directed. Make : JAQUAR Code-ALD-573 or equivalent approved make.

Excavation in post holes (or similar holes) in soft/loose soil each n.exc 0.5 Cum, getting out, returning, filling in an ramming earth or broken rubble mixed with earth around, in layers n.exc 25cm and removing surplus soil to a distance n.exc 50 mtrs complete all as specified and as directed by the Engr-in-Charge.

S&F in repairs 15mm bore Brass CP mixer for mixing holt & cold water screwed down for iron pipe and fixed complete all as specified and as directed. Make : ESSCO Cat Part No. SQT 516KN or equivalent approved make.

Material & labour for PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundation filling and mass concrete etc complete all as specified and as directed.

S&F in repairs Harrison rail, mild steel, chromium plated, 20mm dia with fixing brackets, stops, rollers etc in curtain rails all specified and directed by Engr-in-Charge

M&L for 18-20mm thick Granite Slab green in one piece machine cut, as in steps, jambs, pillars, window cills, cooking platforms and like bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing including rounding to edges of stone slabs such as in steps, cooking platforms, and other similar situations over and including 20mm thick bedding/backing layer in cement mortar (1:6) complete all as specified and as directed.

M&L for bevelling/rounding to edges of granite slab one edge including rubbing and polishing etc complete all as specified and as directed.

M&L for mild steel TMT bars, 10mm dia and over cut to length, bent to shape required including cranking, bending spirally, hooping for columns, hookings ends and binding with and including MS wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L for labour for Mild steel TMT bars 5mm dia and over upto including 10mm dia as in stirrups, spacers and binders cut to length, bend to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L for labour for RCC 1:2:4, type B1 (using 20mm graded stone aggregate) as in slab supported on walls, beams and columns in floor, roofs, landings, balconies, canopies and in shelves and the like work including necessary form work complete all as specified and as directed. Note : Re-inforcement shall be measured and paid separately.

S&F door closer hydraulically regulated, aluminium(die cast) body designation No.3, universal type, suitable for door shutters or 701 to 850mm in width and of weight between 36 to 60 Kg and fixed complete all as specified and as directed.

S&F floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor overall length of cover plate 150mm complete all as specified and as directed.

M&L for brickwork with subclass ''B'' bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and as directed.

Demolition to cement concrete of any description and in any position not otherwise specifically provided for (unreinforced) complete all as specified and as directed.

M&L for brushing neat cement slurry with 3.00 Kg of cement per Sqm complete all as specified and as directed.

M&L for 15mm thick cement screed in cement mortar 1:3 admixed with integral water proofing compound FOSROC complast x 412 IC @ 130 ml per bag cement including a bonding coat of FOSROC''s NiTCO bond AR cement slurry/shalimar Tar product, Mumbai No. 1 liquid @ 200ml per bag complete all as specified and as directed and as per manufactuer's instructions including teting for leakproof treatment.

Demolition of stone or boulders masonry built in cement mortar including all quoins, arches, pillars, pre-cast , PCC bond stones with separating serviceable stones & setting aside for reuse in the work complete all as specified and as directed.

M&L for stone walling of random rubble, uncoursed, well bonded bedded and solidly hearted, built in cement mortar (1:6) including brought up courses complete all as specified and as directed by the Engr-in-Charge

All as per Sl item No. 2.25 here-in-before but except stone. NOTE :- Stone boulders obtained from item No. 2.24 here-in-above shall be used.

Labour only for Hand packing(any thickness) at back of walls over arches etc and raising (or lowering) to the required level. NOTE :- Stone boulders obtained from item No. 2.24 here-in-above shall be used.

S&F grating 125mm dia with hole of PTMT/CP (medium weight 40 gms) complete all as specified and as directed.

S&F in repairs for aluminium anodised, aluminium frames for doors, windows, ventilators with one or more rebates including joinin cleat for fixing etc complete all as specified and as directed. Make : Jindal or equivalent approved make.

S&F aluminium anodised door shutters, aluminium section weighting not less than 0.55 Kg/m including necessary jointing cleats, glazing clips, rubber neoprene packing, handles 02 Nos in each door hinges anodised aluminium snap beading screws etc complete all as specified and as directed. Make : Jindal or equivalent approved make.

S&F aluminium anodised window and ventilator shutters, fixed type without sash bars, aluminium section weighing not less than 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, including aluminium grill and anodised aluminium snap beading screws etc. complete all as specified and as directed. Make : Jindal or equivalent approved make.

S&F aluminium anodised window and ventilator shutters, side hung type without sash aluminium section weighting not less than 0.55 Kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws anodised aluminium fitting such as peg stays 150mm long (1 No) hinges type B-21 100 mm long (2 No) suitable handle (1 No) complete all as specified and as directed. Make : Jindal or equivalent approved make.

Taking down carefully old aluminium anodised door frame/door shutte fixed type window complete and refixing it after repairing of door frame/door shutter, pintal hinges including removing and refixing of door closer including all hinges and all fittings complete all as specified and as directed.

S&F in repair 5mm (tinted) sheet glass, ordinary quality in squares exc 0.5 Sqm each pane complete all as specified and as directed.

S&F in repair 4mm (tinted) sheet glass, ordinary quality in squares n.exc 0.5 Sqm each panel complete all as specified and as directed.

S&F 6mm thick veneered decorative plywood (both side) grade 1 (with BWR resin) with decorative face veneers on both faces, fixed with screws to timber/aluminium frame work complete all as specified and as directed.

S&F for 15mm bore concealed stop cock fancy type chromium plated with long shank and cup complete all as specified and as directed. Make : ESSCO SQT 514 EKN or equivalent approved make.

S&F 100mm size brass handles (decorative type) cast type polished bright complete all as specified and as directed.

S&F PVC (SWR) 50mm bore pipes single socketed, in any length with rubber ring joints, laid in trenches or in floor with necessary clamps, bolts, bends, Tee complete all as specified and as directed.

M&L for pre-cast cement concrete block masonry with solid blocks, type C1 1:3:6 (using 20mm graded stone aggregate) exc 10cm in width and setting in mortar 1:6, complete all as specified and as directed.

M&L for preparation of old painted wooden surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

M/S ANIL KUMAR THAKUR

KARMA SHERPA

M/S S. S CHETTRI AND SONS

KAMLESH ENTERPRISE

KARMA TSETEN BHUTIA

SHANTI KHAWAS AND SONS

SANJAY MITTAL

NISHA CONSTRUCTIONS

MAHENDRA KHAWAS