SPL REPAIR TO BLDG NO P 64 JCO MD ACCN AT UMED VIHAR UNDER AGE B R II AT RMS

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (including backing), removing serviceable tiles to store and rubbish off the premises etc complete all as specified and as directed.

Dismantling Plain corrugated steel sheeting, any gauge, thickness, including, Nanital or similar pattern roof covering etc complete all as specified and as directed.

Dismantling wall and ceiling boards (fibre pulp insulation etc) or insulation boards, slabs, blankets any thickness, incl cover fillets etc complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floors and paving n.exc. 15cm thick (below or above ground level) and removal of rubbish from the site etc complete all as specified and as directed.

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quions, arches, pillers etc complete all as specified and as directed.

Demolition of unreinforced cement concrete of any description and in any position not otherwise specifically provided for etc complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for etc complete all as specified and as directed.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed.

Taking down chowkats with shutter n.exc 1.5 Sqm each (without taking off shutters from the frame) etc complete all as specified and as directed.

Taking down door chowkats with shutter exc 1.5 but not exc 4 sqm each (without taking off shutters from the frame) etc complete all as specified and as directed.

Taking down door shutter exc 1 sqmtr but nex 2 sqmtr each and removing to store etc complete all as specified and as directed.

S&F in replacement of 500 ltr capacity rotational moulded polythylene water storage tanks double layer (cylindrical, vertical with closed top ), including 20mm dia Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed complete all as specified and as directed by Engineer-in-Charge. (Minimum weight 15mm-142gms/ 2 0 m m - 2 1 0 g m s . / 25mm-455gms/ 40mm - 690 gms), all specified in SSR Part-I etc complete all as specified and as directed.

All as item No. 12.00 (here-in-before) but 1000 Ltrs .

Formwork to chajjas including edges for flat rough finished surfaces etc complete all as specified and as directed.

M&L for RCC ,(1:1.5:3) type B-1,( Nominal mix) (using 20mm graded crushed stone aggregate) as in chajjas etc complete all as specified and as directed.

M&L for TMT steel bars 10 mm dia and above, as in reinforcement for concrete, cut to length, bent to shape required including cranking, bending, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm etc complete all as specified and as directed.

All as item No. 16.00 (here-in-before) but 5mm dia and over upto and including 10mm dia as in stirrups, spacers and binders.

M&L for Cement Concrete type D-2 (1:4:8) (using 40 mm graded stone aggregate) as in foundation and mass concrete/sunken floors etc complete all as specified and as directed.

M&L for Cement concrete type B-1 (1:2:4) as in levelling course (using 20 mm graded aggregate), 40 mm thick etc complete all as specified and as directed.

S&F Coloured /light shade vitrified ceramic tiles 10mm thick of area exc 0.18 sqm but not exc 0.36 Sqm each floors laid over and including 15mm thick screed bed or bedding layer of mortar for laying floor finishes in CM (1:4) set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles etc complete all as specified and directed.

All as per item 20.00 (here-in-before) but on vertical surfaces such as skirting , dado risers to steps over and including 10 mm thick bedding layer in CM 1:4.

S&F Non skid ceramic colour tiles of 7 to 8mm thick light colour (Square / rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors laid over and including 15mm thick screed bed or bedding layer of mortar for laying floor finishes in CM (1:6), set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles etc complete all as specified and directed.

M&L for Glazed ceramic colour tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of tiles laid over and including 10mm thick CM (1:4) backing coat etc complete all as specified and directed.

M&L for Preparing the sunken floor slab grouting as specified and appying cement plaster coat laid to slope average 20mm thick in CM 1:3 finished even and fair and applying evenly a tacking coat of industrial bitumen 85/25 @ the rate of 1.2 kg per sqm etc complete all as specified and as directed.

M&L for Water proofing treatment by applying bituminonus primer @ 0.20 kg/sqm providing and laying 3mm thick APP modifide water proofing membrane weighing not less then 3.00 kg/sqm reinforced with non woven polyster mett weighing not less then 160gm/sqm having soften point not less then 140 degree centi grade, longitudinal tensile strength not less then 650N/Sqm, tearing strength of 180 N, by torch application incl min 10cm side over lap and 15cm end over lap and over the membrane etc complete all as specified and as directed.

M&L preparation of roof surface and applying one coat of aluminium primer (reflux) @ 0.10 kg /m applied on treated bituminous membrane etc complete all as specified and as directed.

M&L for screeding 10 mm in cement mortar (1:4) on brick/concrete roof surfaces, using WPC (WPC measured and paid separately), surfaces finished even and smooth without using extra cement etc complete all as specified and as directed.

M&L for Polymer modified bituminous membrane 3 mm thick with sand witched polythene film/non woven polyster reinforcement /polymeric water proofing membrane 3Kg/sqm plastifelt/hyperplas /multiplas / shivam or equivalent ) laid over hot blown grade85/25@ 1.2kg/Sqm (i.e roof slab cleaned throughly to to remove all loose particle dust/dirt particle ) shall be laid over entire roof surface over 4kg/Sqm bituminous primer and on verticle surface up to grooves ( or as per manufacturers recommendation) with over laps of 100mm The over lap shall be sealed by flames or as per manufacturer instruction.Hot blown bitumen grade 85/25 @1.2kg/Sqm applied over the membrane should be compatible with membrane all as recommendation manufacturers etc complete all as specified and as directed.

M&L for brushing neat cement slurry with 3 kg of cement per square metre etc complete all as specified and as directed.

M&L 40 mm thick cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate as in slope correction layer over RCC slab finished without using extra cement etc complete all as specified and as directed.

M&L for Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or etc., and making good, cutting not exc 10 cm girth etc complete all as specified and as directed.

M&L for factory made Pressed steel frames(1.25 mm thick MS sheet) of size 105x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc.,including one shop coat of primer etc complete all as specified and directed.

M&L for factory made Pressed steel frames(1.25 mm thick MS sheet) of size 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc.,including one shop coat of primer etc complete all as specified and directed.

S&F Plain, solid straight chowkat and frames, wrought, frmed rebated on the solid, rounded or chamfred put together with glue pinned at joints , supplied and fixed in 2nd class hard wood etc complete all as specified and as directed.

S&F factory made 35mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides etc complete all as specified and as directed.

M&L for 0.90mm thick Decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructions etc complete all as specified and as directed.

M&L for 35 mm thick factory made second class hard wood glazed and skelton shutter, open rbatd and prepared to receive glass, gauze etc (with out sash bar ) edges of framing plain, camfered or rounded, fitted with cut and mitred beads for securing glass etc size of members of shutters as specified in SSR Part -I section 8 clause 8.42(a) supplied and fitted to chowkat etc complete all as specified and as directed.

Supply and fix stainless stelel wire cloth 0.36 nominal dia of wire and average width apperture 1.40mm and fixed with stainless steel wire staples or wooden beads supplied with shutter etc complete all as specified and as directed.

S&F for providing sliding type (3 Track +3 shutter) aluminium windows, section profiles of aluminium as per sketch No SK/2019/01 dated 21/01/19, aluminium alloy extruded sections conforming to HE 9-WP of BIS 733 and HP 9 -WP of BIS 1285 as amended, with minimum thickness of frames (outer bottom, Top & side ) 1.5mm and sliding sash (stiles & rails) of minimum thickness 1.2 mm. The windows shall be procured from a BIS license factory manufactoring windows to BIS-1948, The EPDM gaskets, rollers, recessed handles cum locks aluminium snap beading for receving glass/wiremesh with stainlss steel screws shall be provided with windows etc complete all as specified and as directed.. The aluminium extruded section shall be of make Jindal/Hindalco/Halco extrusions etc all as listed. Note:- Glazing and Stainless steel wire mesh will be paid seperately.

S&F anodised aluminium powder coated any colour frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and as directed.

M&L for Preparing new wooden surface and applying two coats of synthetic enamel paint over a coat of pink primer etc complete all as specified and as directed.

M&L for preparation of old painted wood and wood based surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint in any tint all as specified and directed

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification etc complete all as specified and as directed.

S&F for Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification etc complete all as specified and as directed.

S&F 250 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed etc complete all as specified and as directed.

S&F 150 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed etc complete all as specified and as directed.

S&F 100 mm thick Butt hinges, medium weight, cold rolled mild steel, and fixedetc complete all as specified and as directed.

S&F Aluminium bow handles, cast type, anodised 150 mm long etc complete all as specified and as directed.

S&F Aluminium bow handles, cast type, anodised 125 mm long etc complete all as specified and as directed.

S&F 200 mm long Aluminium, anodised, barrel tower bolts of extruded section and fixed etc complete all as specified and as directed.

M&L for Second class clean sawn hardwood in scantling fixed in timber framed work etc complete all as specified and as directed.

M&L for 18 mm thick prelaminated Medium density fibre board, Exterior grade, fixed to timber frame-work with stain less steel screws fixed in repairs etc complete all as specified and as directed.

S&F 75mm Hasp and staple, safety type, aluminium anodised mild steel hinge pin including bolt to hinge plate and fixed with screws etc complete all as specified and as directed.

S&F Continuous (piano) hinges, mild steel bright finish or electro galvanised with flap (when open) 40 mm, fixed with steel screws etc complete all as specified and as directed.

S&F 150mm long mild steel ordinary rat tail rod pattern springs including roller and roller complete etc complete all as specified and as directed.

M&L for Brickwork with subclass ‘B’ bricks(using old size burnt bricks), straight or curved on plan exc 6m mean radius, built in CM 1:6 etc complete all as specified and as directed.

M&L for brick work with sub class 'B' bricks (using old size burnt bricks) straight or curved on plan in any radius in half brick thick walls built in cement mortar 1:4, complete all as specified and directed

M&L for Brickwork with subclass ‘B’ bricks(using old size burnt bricks) retrieved from demolition under item 05 above including cleaning and removal of mortar from old bricks etc complete all as specified and as directed.

M&L for Rendering 10mm thick cement plaster in CM (1:6) on brick work/concrete surfaces finished even and fair without using extra cement etc complete all as specified and as directed.

M&L for rendering 15 mm thick cement plaster in CM (1:4) on brick work/concrete surfaces finished even and fair with WPC @ 2% by weight of cement content and without using extra cement etc complete all as specified and as directed. (Note:-WPC will be measured and paid separately)

M&L for rendering 5 mm thick cement plaster in CM (1:3) on ceiling finished even and fair etc complete all as specified and as directed.

M&L for Complete removal of existing treatment and applying two coats of oil bound distemper white or tinted on walls over a coat of alkali resistant primer over 1.5mm thick wall care putty etc complete all as specified and as directed.

M&L for preparation of new plastered surfaces of wall applying two coats OBD white or tinted on walls over a coat of alkali resistant primer over 1.5mm thick wall care putty of approved shade etc complete all as specified and as directed.

M&L for Complete removal of existing treatment and applying 2 coats of oil bound distemper white or tinted over a coat of alkali resistant primer over 1.5 mm thick cement based wall care putty over ceiling etc complete all as specified and as directed.

M&L for Preparation of newely plastered surface and applying two coats of oil bound distemper white or tinted over a coat of alkali resistant primer over 1.5 mm thick cement based wall care putty over ceiling etc complete all as specified and as directed.

M&L for preparation of old painted surfaces by removing the existing treatment completely and applying two coats on external wall of Antifungal exterior emulsion paint over a coat of primer and 1.5coats of wall care putty etc complete all as specified and as directed.

All as per Item No 67.00(here-in-before) but on newly plastered surfaces on external wall .

M&L for one coat of White wash on old plastered surfaces of ceiling including preparation of surfaces etc complete all as specified and as directed.

Taking down 15mm dia bore GI steel tubing and connection including fittings etc complete all as specified and as directed.

Taking down 20mm dia bore GI steel tubing and connection including fittings etc complete all as specified and as directed.

Taking down 25 mm dia bore GI steel tubing and connection including fittings etc complete all as specified and as directed.

S&F in repairs Vitreous china wash down water closet pan, (pedestal pattern), white, with and including plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device etc complete all as specified and as directed.

S&F in repair Vitreous china wash basin, white, flat back, size 550x400mm including brackets, cutting for and pinning in ends of brackets or erecting stand, brass chromium plated perforated waste coupling/ fittings 32 mm dia with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed and PVC waste pipe of 32mm bore and of suitable length, etc complete all as specified and as directed.

S&F in repair flushing cistern 10ltr capacity body molded from design quality high impact polly propylene critical, PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and 15mm bore 450mm long PVC connection etc complete all as specified and as directed.

S&F CPVC pipes, SDR 11 , 25 mm outer dia conforming to IS - 15778 with all fittings such as Tee, bends ,elbows, unions sockets and end oieces etc to receive the fittings and fixed with solvent concealed in wall , floor and ceiling etc complete all as specified and as directed.

All as per item 76.00 (here-in-before) but of 20 mm dia.

All as per item 76.00 (here-in-before) but of 40 mm dia.

S&F in repairs PVC connection low density polythene pipe 15 mm dia , 450 mm long , heavy duty with PTMT nuts etc complete all as specified and as directed.

S&F in repairs Pillar tap, chromium plated, fancy type, screwed down with high pressure, with or without lettered 'Hot' or 'Cold' with long screw shanks and fly nuts, screwed for iron pipe and fixed for 15 mm bore dia of pipe etc complete all as specified and as directed. Make : Cera Cat No QT F2006101 or equivalent in Hindware/Parryware.

S&F in repairs 15 mm bore Bib cock , chromium plated with fancy type and screwed down to 15mm bore GI tubing or for brass ferule including taking down old bib cock etc complete all as specified and as directed. Make : Cera Cat No. QT F2006151 or equivalent in Hindware/ Parryware.

All as per item 81.00 (here-in-before) but two way bib cock .

S&F in repairs Angle stop valve with wall flange 15 mm bore of pipe brass chromium plated, screwed down, high pressure screwed both ends for iron pipe for unions and fixed including taking down old stop valve etc complete all as specified and as directed. Make : Cera Cat No.QT F2006201 OR equivalent in Hindware/Parryware.

S&F in repairs Brass chromium plated toilet paper holder etc complete all as specified and as directed. Make : Cera Cat part -F 5007109 or equivalent as per make of list attached as APPX 'B" of tender document.

S&F in repairs Stainless steel soap dish white of size 160 x 160 x 90 mm as approved fixed with brass screws or embedded in wall etc complete all as specified and as directed. Make : Cera Cat part F 5003106 or equivalent as per make of list attached as APPX 'B" of tender document.

S&F in repairs Health faucet of brass body with wall hook and 1mtr flexible stainless steel braided rubber hose pipe fixed in repair etc complete all as specified and as directed. Cera Cat part No F 8030102 or equivalent as per make of list attached as APPX 'B" of tender document.

S&F in repairs Towel rail chromium plated fancy type 60cm long including bracket fixed between flanges complete etc complete all as specified and as directed. Make : Cera Cat part F 5007103 - or equivalent as per make of list attached as APPX 'B" of tender document.

S&F in repairs Brass chromium plated over head 15 mm bore shower rose 120mm dia with 3 flow swivel joint including shower arm fixing to steel pipe or union including taking down old shower rose etc complete all as specified and as directed. Make Cera Cat No F 7020305 shower arm F 7040104 or equivalent as per make of list attached as APPX 'B" of tender document.

S&F in repairs Brass CP wall mixer for mixing hot & cold water screwed down for iron pipe and fixed etc complete all as specified and as directed.

Supply only Integral Water Proofing (liquid) Compound etc complete all as specified and as directed.

S&F PVC (SWR) pipes of dia 110mm bore double socketed in any length with rubber ring joints fiexed to walls etc complete all as specified and as directed.

S&F PVC (SWR) pipe of 75 mm bore in double socketed in any length with rubber ring joints fixed to walls etc complete all as specified and as directed.

S&F PVC Nahani traps 75 mm outlet with stainless steel cover grating etc complete all as specified and as directed.

S&F PVC (SWR) bends of 75mm bore in radius etc complete all as specified and as directed.

S&F PVC (SWR) bends of 110 mm bore in radius etc complete all as specified and as directed.

S&F Salt glazed stone ware gully traps square or round mouthed type 150 mm x 150 mm. type 'P' etc complete all as specified and as directed.

M&L Cement concrete type C-2 (1:3:6) (40mm graded stone aggregate) in MS pipe posts and mass concrete on roof top etc complete all as specified and as directed.

M&L Cutting holes into pr through cement concrete slabs ,chajjas etc reinforced or superficial area Exc 100 sqcm but N.exc 250 sq cm etc complete all as specified and as directed.

M&L Cutting ,grooves or rebates n.exc 15cm girth and triming surface for inserting pre-painted galvatume sheet with or wihtout reinforcement etc complete all as specified and as directed.

Filleting in any position and to any shape sectional area exc 25 but not exc 50 sqm in CM1:3 etc complete all as specified and as directed.

S&F for Steel work in MS tublar trusses, MS Square Tube ,Purlin,rafter including special shaped washer etc complete using ERW or indication butt welded tubes confirming to I.S 1161-1998 grade St-240 etc complete all as specified and as directed.

S&F for Joist,channel ,angle,or tee sections,fixed independently, without connecting plates ,etc (cut to ordinary length ie within 20mm of the length indicated Fe -410-W(Gde-E-250 qaulity-B) etc complete all as specified and as directed.

S&F Plates (plain or chequered) channels,square cut or notched (ordinary and counter shunk forming holes,without any attachement etc complete all as specified and as directed.

S&F Wind ties for roof including securing bolts ,posts and struts including all necessary drilling bolt or riveting etc. and similar work confirming to FE-290 Gde-165 etc complete all as specified and as directed.

S&F Pre-painted galvalume aluminium zinc coating GI based trapezoidal profile steel sheet 0.50mm (TCT) any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall,fixed with self tapping screws etc complete all as specified and as directed.

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick on ridge any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall,fixed with self tapping screws etc complete all as specified and as directed.

M&L for Preparation of two coats of synthetic enamel paint over one coat of red oxide,zinc chrome primer on newly prepared steel surface of any description,over 10cm width or girth,not other wise described etc complete all as specified and as directed.

M&L for Preparation of two coats of synthetic enamel paints surfaces of any description, n.exc 10cm in width or girth when unconnected with other painting or when painted in a different tint, over a coat of red oxide, zink crome primer etc complete all as specified and as directed.

S&F 0.56 mm thick plain Aluminum sheeting ,Alloy 31000H4 in gutter,drip and straight flashing(length and girth as fixed) etc complete all as specified and as directed.

S&F 16 to 20mm dia Mild steel screws bolts(Machine made)with hexagonal or square heads at one end and screwed both ends ,each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 10cm and n.exc 15cm long. with washers etc complete all as specified and as directed.

M&L for Preparation of old painted surfaces of steel & Iron of any description over 10 cm width or girth and applying one coat of synthetic enamel paint (1st quality) etc complete all as specified and as directed.

S&F in repairs 20 mm dia powder coated aluminium curtain rails fixing with fancy brackets and closing caps etc complete all as specified and as directed.

Taking down old unserviceable GI pipe 40 mm dia from the wall /trenches by disconnecting of water connection etc complete all as specified and as directed.

S&F Pipes galvanized medium class with all fittings complete including fittings of size 40 mm dia etc complete all as specified and as directed.

S&F Gun metal globe or gate valves of size 40 m dia with iron wheels head , screwed both end for iron pipe etc complete all as specified and as directed.

M&L for Cement concrete tiles 25cm x 25cm x 22mm thick, with grey cement and with pigment laid over 15 mm thick screed in CM (1:6) mixed with water proofing compound ,joints grouted and flush pointed in CM (1:3) mixed with 5% of crude oil by weigt of cement etc complete all as specified and as directed.

S&F in repairs 1mm thick stainless steel sink, plugs, washers, PVC waste pipe, union, CP coupling & cantilever brackets embedded in cement and sand mortar in wall , ovesinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mmrall size of sink 495mmx420mm, bowl size 410mmx330mmx 160 mm as in repair etc complete all as specified and as directed.

S&F in repairs stainless steel plate rack of standard pattern & of size 790x610x220mm thickness of stainless steel sheet shall be 304 AISI including fixing to wall with 4 nos 50 mm screws & pvc rawl plugs etc complete all as specified and as directed.

S & F for 4 mm thick of size 600x600mm HSPC (high pressure Steam Cured) pre-Painted self embossed, textured designer board E-Board Classic to be fixed Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre. fixed in ceiling flat or Sloping etc complete all as specified and as directed.

M&L Cement concrete (1:3:6), type C-2 using 40mm graded stone aggregate as in filling of steel chowkhats including necessary form work etc complete all as specified and as directed.

M&L Machine cut kota stone slab flooring 18-22mm thick over 20 mm cement screed base CM (1:6) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing polishing and rounded or chamfered for nosing etc complete all as specified and as directed.

M&L Kota stone slab 12-15mm thick in riser of steps, skirting, dado and pillar laid over 15 mm thick rendering (1:4) and jointed with ditto as per above item no 102

M&L for 18-20mm thick Granite (of any type) machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing etc complete all as specified and as directed.

M&L for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms, laid over and including 20mm thick screed bed/bedding layer in cement mortar (1:4) and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite etc. complete all as specified and directed.

M&L Granite (of any type) 20mm thick machine cut, as in skirting/dadoes, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete as in vertical surfaces over 20mm thick screed bed in CM (1:3) etc complete all as specified and as directed.

M&L for 100mm thick Plain cement concrete (1:4:8) type D-2 using 40mm graded stone aggregate as in sub base etc complete all as specified and as directed.

M&L 80mm thick Coloured (Yellow & red) interlocking (M-35) cement concrete tiles of approved design & pattern with grey cement and pigment laid over and including 25 mm thick layer of sand cushioning,etc complete all as specified and as directed.

M&L Sand filling under floors or in foundations including watering and consolidation etc complete all as specified and as directed.

Cutting holes in brick walls exc half bricks but not exc one brick built in cement mortar or cement lime mortar and stone walls built in lime mortar etc complete all as specified and as directed.

M & L 25mm thick second class hard wood boarding , plained one side with butt joints as in eaves boards etc complete all as specified and as directed.

M&L for 75 mm thick PCC 1:3:6 type C2 , using 40 mm graded stone aggregate in plinth protection/aprons/path laid to slope of 1:12, finished fair and even without using extra cement with and including all necessary formwork to divide tha area in panels, finishing exposed edges fair or rounding or chamfering where directed and providing 10 mm wide joints throughout thickness of plinth protection duly filled with mastic filling (one part of hot bitumen 85/25 and three part of fine sand by weight) complete all as specified and directed.

Taking down carefully copper/ aluminium point wiring (light, fan, socket or power) complete, including fitting & fixtures such as switches with board, ceiling roses, pendents, bell/ buzzer, bell push, lamp holders, regulators, sockets, light fittings etc., removing material from site and making good to the disturbed surfaces of walls, ceiling, floors etc. including making good the disturbed surfaces and paint touch up to match with the existing surface complete all as specified and as directed.

Material and labour for (concelaed Type) point wiring including necessary chases cutting of wall for one light/fan/call bell point with 1.5 sqmm PVC insulated (FR-LSH) PVC sheathed multistranded copper conductor cable 1100 volts grade controlled by one way switch including 1.5 sqmm PVC (FR-LSH) insulated unsheathed copper cable multistrand conductor 1100 volts grade for continuity earth wire connected to common earth dolly drawn through and including PVC conduit with all accessories and sunk GI box for mounting of fittings like switch, socket and fan regulator etc and making good the distrubed surfaces as per the existing complete all as specified and as directed by the Engr-in-Charge

(a) One light point controlled by one, one way switch .

(b) One Ceiling fan/ exhaust fan point controlled by one, one way switch.

(c) One 3 pin socket outlet 5 Amps on the same board with other switches.

(d) One 3 pin socket outlet 5 Amps on the Independent board.

(e) One bell point controlled by one, one way switch .

(f) One light point control by two way switch

All as per item No- 135.00 here-in-before but with 2.5 Sq mm for 3 pin 15 Amps socket point controlled by one switch on independent board and 2.5 Sq mm copper conductor green in colour as earth continuity conductor connected to common earth dolly etc complete all as specified and as directed.

All as per item No-135.00 here-in-before but with 4.0 Sq mm for AC point controlled by 4.0 Sq mm copper conductor green in colour as earth continuity conductor connected to common earth dolly etc complete all as specified and as directed.

M&L for Switch piano flush type single pole, one way 5A etc complete all as specified and as directed.

M&L for Socket outlet, 2 in 1, 3 pin 5A flush type etc complete all as specified and as directed.

M&L Switch socket combination 2 in 1, 5A flush type etc complete all as specified and as directed.

M&L Switch socket combination 2 in 1, 5A/16A, 5 in 1 flush type etc complete all as specified and as directed.

M&L for bell push switch 5 amps piano type flush type etc complete all as specified and as directed.

M&L for bell AC 230 volts musical type etc complete all as specified and as directed.

M&L for Switch piano, flush type single pole,two way 6 Amp etc complete all as specified and as directed.

M&L for stepped type electronic fan regulator 100/120 Watt socket size flush type on the existing phenolic laminated sheet etc complete all as specified and as directed.

Taking down existing burnt aluminium/ copper sub main wiring and M&L for sub main wiring with two runs of 4.0 Sq mm and one run of 4.0 Sq mm for earth wire with multi standard copper conductors FRLSH quality, 1100 volts grade, drawn through and including non metalic rigid PVC conduit with all conduit accessories (including concealing and making good to the disturbed surfaces of walls, ceiling, floors etc. including making good the disturbed surfaces and paint touch up to match with the existing surface) etc complete all as specified and as directed. NOTE:- Two runs of 4.0 Sq mm + one run of 4.0 Sq mm and one run of PVC Conduit and its accessories of suitable size shall be measured as one unit length.

All as per item No 13.00 but sub main wiring with two runs of 2.5 Sq mm and one run of 2.5 Sq mm for earth wire NOTE:- two runs of 2.5 Sq mm + one run of 2.5 Sq mm and one run of PVC Conduit and its accessories of suitable size shall be measured as one unit length etc complete all as specified and as directed.

M&L for 20W LED, 4', Wall mounted LED tube light fitting batten with LED single side or double side connection, extruded aluminium heat sink provided for efficient heat dissipation & integrated electronic driver.etc with all accessories internally pre-wired and fixing the same on and including two Nos PVC blocks and connecting up with flexible copper cable of size 0.75 Sq mm 3 core from ceiling rose to the light fitting including taking down old unsv light fitting etc complete all as specified and as directed.

M&L for 10W LED, 2', Wall mounted polycarbonate batten internally pre-wired with electronic driver and polycarbonate diffuser and fixing the same on and including two Nos PVC blocks and connecting up with flexible copper cable of size 0.75 Sq mm 3 core from ceiling rose to the light fitting including taking down old unsv light fitting etc complete all as specified and as directed.

M&L in replacement for decorative wall mounted light fitting made up of polycarbonate including 9 watt LED lamp with B-22 base including taking down old unsv holder fitting etc complete all as specified and as directed.

M&L for ceiling rose 3 terminal PVC/Polycarbonate isolated body etc complete all as specified and as directed.

M&L for Bldg Security LED 1x25W light fitting, drawn through including GI bracket of 25mm bore light grade bent to shape and fixed on wall with metal fastners 2 Nos 10mm dia incl drilling holes as required and connecting up with flexible copper cable of size 0.75 Sq mm 3 core from ceiling rose to the light fitting including taking down old unsv light fitting etc complete all as specified and as directed.

Supply and fixing for Bed side light 3Watt LED light reading in bed just got easier with this colletion of adjustable LED bedside lights etc complete all as specified and as directed. Make : Philips Cat Part No48042/Bajaj/Havells

M&L for VTPN DPX 4 way,double door 415 Volts, 50 Hz, IP 43 IK 09 sheet steel, powder painted, with 02 neutral link & 02 earth bar and cable ties for cable management suitable for fixing of MCCB as incomer and MCB SP/TP as outgoing MCB DBs incl taking down of old UNSV DBs and making good the disturbed surfaces to match with existing specification , etc complete all as specified and as directed. Note : MCBs will be measured sepeartely.

M&L for MCCB 4 Pole, 415 V, Adjustable type, 63 Amps with breaking capacity 16 KA taking down old unsv MCB etc complete all as specified and as directed.

M&L for MCB Distribution board double door type SPN 8 way, sheet steel, powder painted, with bus bar neutral link & earth bar etc. and fixing MCBs of various rating capacity including taking down old unsv DB and making good the disturbed surfaces to match with existing specification , etc complete all as specified and as directed. Note : MCBs will be measured sepeartely.

S&F sheet metal enclosure with socket plug top and MCBs single pole 32 Amps and neutral encloser with two pin and earth plug and socke complete one single pole MCB SP 20 Amps including metal encloser etc complete all as specified and as directed.

MSupply and fixing MCB SPN 32 Amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning MCB DB incl taking down old unsv MCB etc complete all as specified and as directed.

Supply and fixing MCB SP 6 to 32 Amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning MCB DB incl taking down old unsv MCB etc complete all as specified and as directed.

Material & labour for cutting/ digging of existing Hard surface of cement concreet/Bituminous road of size not less than 45 cm in width and 20 cm deep for laying of GI/CI pipe & making good to the disturbed surfaces by providing PCC or same material after laying of pipe line and returning filling of soil etc complete all as specified and as directed.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250m etc complete all as specified and as directed. Note : Old Exhaust Fan shall be deposited to EM store yard.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300mm sweep with, blades, and frame and louvers etc complete all as specified and as directed. Note : Old Exhaust Fan shall be deposited to EM store yard.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200mm sweep. Min air delivery 210 CFM with service valuenot less than 5.1 BEE. Five star rated with brushless direct current motor (BLDC) etc complete all as specified and as directed. Note : Old Exhaust Fan shall be deposited to EM store yard.

Supply, Fixing and testing of vertical type wall mounted storage water heater of Capacity 25 Ltrs BEE 5 Star rated or minimum Standing Loss of 0.511 kWh , 240V, 50Hz with Maximum power consumption of 2KW , dry powder fero glass line coating technology for inner tank with incoloy heating element with minimum 4 years warranty , ABS outer body , 2 units of PVC connection pipe with length of 450mm length for hot and cold water supply with complete Accessories etc complete all as specified and as directed.

Supply, installation, testing and commissioning of factory made meter panel board wall mounted made out of CRCA sheet of 2mm thick indoor type totally enclosed weather proof, dust vermin proof with front openable, hinged door locking arrangement mounted on MS clamp welded to panel body duly grouted in wall including provn of Acrlylic sheet for meter reading, space for refixing of single phase smart meter 5-60 Amps 04 Nos AC 230 Volts incl lugs, spacer mounting chanels, rubber gasket, locking knobs, PVC shrinkable sleeves, nut bolts, washers etc, suitable compartment of every meter and control MCB circuit and epoxy powder coated spray paint with primer, CPRI type tested complete all as directed including the following accessories :- Incoming (a) MCCB 63 Amps 4P, 415 volts, 16 KA - 01 No (b) R-Y-B phase LED indicating lamp 03 Nos (c) Copper wiring in panel of suitable size. Outgoing (a) MCB SPN 40-63 Amps, 230 volts 10 KA 'C Curve' - 06 Nos (b) Refixing existing smart meters - 04 Nos ( Note : to be insured properly maching the qtr Nos before fixing the smart meters)

Taking down burnt unsv LT UG cable of any size and M&L for laying of LT UG cable, XLPE insulated, galvanised steel strip or wire armoured, heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area of 25 sq mm, 4 core etc complete all as specified and as directed. NOTE :- (i) Excavation and earth work, sand cushioning, cable protection cover, pipe etc. shall be measured and paid seperately under relevant items.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m depth and getting out in soft/ loose soil etc complete all as specified and as directed.

Returning filling in trenches including spreading leveling watering and well ramming in layers not exceeding 25 cm thick all etc complete all as specified and as directed.

Removing of excavated material not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point all etc complete all as specified and as directed.

M&L for spread fine river sand in trenches etc complete all as specified and as directed. NOTE: For measurement purpose, punned down thickness shall only be taken.

Supply & laying tubes ' light grade' galvanised, with all fittings, fixed complete to walls, poles, ceilings or laid in floors/ trenches/ road crossing for protection of cables of size 40 mm dia bore including taking down corroded GI tubing etc complete all as specified and as directed.

M&L for laying brick sub class 'B' old size burnt bricks for cable protection of size 230mmx115mmx75mm etc complete all as specified and as directed.

Supply and laying tubes Medium grade galvanised GI tubing with all fittings, fixed complete to walls/poles/laid in floors/trenchs/road crossing of size 25mm dia bore including etc complete all as specified and as directed.

S&F Stop valves 25mm, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed etc complete all as specified and as directed.

M&L for earthing complete with galvanized steel earth plate electrode of size 600x600x6mm thick buried directly in ground (earth pit not less than 2.25m deep below the normal ground level) with top edge of the earth plate not less than 1.5 mtr below normal ground level connected to galvanised earth lead wire 4 mm dia as earth lead connectd by means of bolts, nuts, washers and check nuts all as shown in electrical plate No 3 of MES SSR Part-I, including testing on completion etc complete all as specified and as directed. NOTE:- (i) The unit rate shall also included for earth work in hard/ dense soil, PCC (1:3:6) type C1 chamber, CI cover 10 m thick, funnel with GI watering pipe 20mm dia Medium grade, GI protection pipe light grade 15mm dia and wire mesh complete in addition to item No 1 (a) to (e) of preamble (notes) under sub heading earthing, specified on Sl Page No 389 of MES SSR Part-II. (ii) Earthing lead and GI protection pipe beyond 7.5m will be measured and paid separately. (iii) Test points shall be made of GI strip 32x6 mm bridge type mounted on insulators, where ever applicable

commercial enterprises

Kalim sons

Shri Atoshe Tuccu

KAILASH KUMAR LADHA

Shri B K Ukil

M/S SANGITA TRADERS