CONSTRUCTION OF MPC (MULTI PURPOSE CENTER ) AT KURU BLOCK KURU DIST LOHARDAGA

Earthwork in excavation in foundation trenches in ordinary soil (vide classfication of soil item - A) and disposal of excavated earth a obtained to a distance up to 50M including all lifts with leveling ramming the foundation trenches removing roots of trees shurbs all complete as per approved design and per building specification and direction of E/I.

Extra for earth work in hard soil as per specification and direction of E/I. (vide classfication of soil item - B)

Earth filling in foundation trenches and plinth in layer not exceeding 150mm thick will watered rammed fully compacted and fine dressed with earth obtained from excavation of foundation trenched with a lead of 50mm and lift of 1.5M all complete as per building specification and direction of E/I. (Mode of measurement compacted volume).

Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including' cost of all materials, labour, royalty and taxes all complete as per building specification and direction of E/l (Mode of measurement complacted volume).

Earth filling in foundation trenches and plinth in layers not exceeding 150 mm. thick well watered, rammed, fully compacted and fine dressed with earth obtained after cutting within a lead of 50 M. and lift of 1.5 M all complete as per building specification and direction of E/l (Mode of measurement compacted volume).

Extra for each subsequent lead upto 25 M beyond the initial lead of 50 M (Maximum upto 150M lead by head load) as per specification and direction of E/l.

Providing designation 75 A one brick flat soling joints filled with local sand including cost of watering texes royalty all complete as per building specification and direction of E/I.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level: 1:3:6 (1 Cement: 3 coarse sand (zone-|||):6 graded stone aggregate 20 mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level. 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)

Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mmnominal size)

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 20mm nominal size).

Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mmnominal size)

Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts

Providing designation 75 A brick work in C.M. (1:4) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/l.

Providing designation 100A brick work with fly ash lime brick (FLAG) conforming to IS 12894-1990 (9"x4.5"x3") in C.M. (1:6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing designation 100A brick work with fly ash lime brick (FLAG) conforming to IS 12894-1990 (9"x4.5"x3") in C.M. (1:6) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing designation 112mm thick reinforced designation 100A brick work with fly ash lime brick (FLAG) conforming to IS 12894-1990 (9"x4.5"x3") in C.M. (1:4) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening,carriage of materials,scaffolding, raking out joints to 15mm depth, curing, taxes and royalty (but excluding the cost of rienforcement)all complete as per building specification and direction of E/I.

Reinforced cement concrete work in beam, suspended floors,roofs having slop 15 landings, balconies, shelves,chajjas, lintels,band,plain window sills,staircases and sporal stair case above plinth level up to floor five level,excluding the cost of centring,shuttering,finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-|||) : 3 graded stone aggregate 20 mm nominal size)

Centring and shuttering including strutting,propping etc. and removal of form for (Lintels,beam plinth beam,girders,bressumers and cantilevers.with water proof ply 12mm thick)

Reinforced cement work in arches,archibs,domes,vaults,shell,folded plate and roof having slope more than 15 up to floor five level,excluding the cost of centring,shuttering,finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-|||) : 3 graded stone aggregate 20 mm nominal size)

Centring and shuttering including strutting,propping etc. and removal of form for (Suspended floor,roof,landing,balcconies and acces platform with waterr proof ply 12 mm thick)

Providing 12mm cement plaster (1:6) with clean coarse sand of F.M 1.5 including screening curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I

Providing 1.5mm cement punning including curing, carriage of water with all leads and lifts as per building specification and direction of E/l.

Providing 12mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5with 5% cico or any other approved water proofing compoundincluding taxes and royalty all complete as per building specification and direction of E/l.

Providing 6mm thick cement plaster (1:4) in ceiling with clean coarse sand of F.M 1.5 including screening curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge:Fixing with adjustable lugs with split end tail to each jamb

Supplying, fitting and fixing 35mm thick solid core type non-decorative single leaf flush shutters in doors and windows with black board core blended with high quality phenol formal dehyde synthetic resin both side commercial veneered of standard make with oxidised iron fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/l.

Supplying, fitting and fixing fully glazed steel door, windows or ventilations of standard rolled 'Z' and mullion steel sections and size as per IS-1038 joints met and welded with 100x16x3mm M.S. lugs fixed in cement concrete (1:2:4) blocks 15x10x10 cm size including cost of oxidised iron fittings, with hinges, handle per steps, catch springs, 3mm thick plain glass panes with Aluminimum beads and inner frame fixed with lugs with 20mm long 6.3mm G.I. counter sunk machine screw and nuts and applying a coat of red lead paint carriage to work site hoisting and placing in position in all storys and taxes all complete as per building specification and direction of E/l.

Providing and fixing factory made P.V.C. door frame of size 50x47 mm with awall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer’s specification and direction of Engineerin- Charge.

Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC 'C' channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer's specification &

Supplying, fitting and fixing M.S. grill made of 20x6mm M.S. flat as per approved design and drawing, properly fabricated with joints continuous fillet welded and finished smooth , carriage of grill to work site, hoisting as per building specification and direction of E/l. (where materials is not supplied by the deptt.)

Providing primer one coat of approved shade and make over new wooden surface including preparing the surface after cleaning, removing dirt,, scales, smokes, grease and sand papering, including cost of scaffolding and taxes all complete as per building specfication and direction of E/l

Providing two coats of synthetic enamel paint over a coat of primer of approved shade and make over new wooden surface after cleaning, removing dirt, scales, smokes, grease and sand papering, including cost of scaffolding and taxes all complete as per building specfication and direction of E/l.

Providing primer one coat of red lead paint of approved make over new steel surface including preparing the surface after cleaning, removing rust , dirt, , scales , smokes and grease and cleaning the surface thoroughly including cost of scaffolding and taxes all complete as per building specification and direction of E/l. ( Mode of measurement Area shall be multiplied by the co-efficient as indicated in building specification)

Providing two coats of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface thoroughly, scaffolding and taxes all complete as per building specification and direciton of E/l.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Providing two coats of dry distemper of approved shade and make over a primer coat of washing over new surface including preparing the plastered surface by rubbing smooth with pumice stone or fine sand paper, applying putty wherever required, scaffolding, washing of floors and taxes all complete as per building specification and direction of E/l.

Providing two coats of oil bound distemper of approved shade and make over a coat of cement primer over new surface including preparing the plastered surface by rubbing smooth with pumice stone or fine sand paper, applying putty wherever required, scaffolding, washing of floors and taxes all complete as per building specification and direction of E/l.

Providing 50mm thick cement concrete flooring (1:2:4) with 20 mm to 6mm size graded stone chips finished with flooring coat of neat cement in panels including cost of curing finishing the surface smooth by rubbing with carborandum stone taxes royalty all complete as per building specification and direction of E/I

Providing and laying Double charge vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 / ISO 13006 of approved make, in all colors and shades, laid on 20mm thick cement mortar 1:4 (1 cement: 4 coarse sand ), jointing with grey cement slurry @3.3kg/sqm including grouting the joints with white cement and matching pigments, etc, complete Size of Tile 600x600 mm.

Providing and laying 6mm precast white glazed tiles in walls over 12mm cement mortar (1:3) and jointed with grey cement slurry flush pointed with white cement including rubbing, polishing, and cost of curing, taxes, and royalty all complete as per building specification and direction of E/l.

Providing and laying 15 mm - 23 mm thick Kota stone tiles in risers of steps, skirting, and pillars of approved size, texture, and color applied over 12mm thick cement mortar (1:3) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing to granolithic finish with approved quality of carborundum stone including the cost of curing, taxes, and royalty all complete as per building specification and direction of E/I. (i) 300 x 300 mm size

Providing Toe steel reinforcement of 8mm dia to 32mm dia rods as approved design and drawing excluding carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I. TMT Fe 500 (Only Valid for SAIL & TATA STeel) 8#- @ 20%

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthned clear float glass 6mm thick, spacer tube 12mm wide, dessicants, including primary seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor. (Payment for fixing of IGU Panels in the curtain glazing is included in cost of item No.25.2) For payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm.Coloured tinted float glass 6mm thick substrate with reflective soft coating on face # 2, + 12mm Airgap + 6mm Heat Strengthened clear Glass of approved make having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2 degree K etc. The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement.

Steel work welded in built up sections/ framed work, including cutting,hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required,

Wiring for light point /fan point/ exhaust fan point/ cell bell point, with 1.5 sq. mm FR PVC insulated copper conductor singel core in surface/recessed PVC conduit, with modular type switch, modular plate sutable GI box etc as required. Group C

Power Plug wiring in PVC Conduit (2X4 Sq.mm) :- Wiring for light/power plug with 2x4 Sq.mm FR PVC insulated copper conductor songle core cable in surface/recessed PVC conduit along with 1 No. 4 Sq.mm FR PVC insulated copper conductor single core cable for loop earthing etc. as required.

Circuit/Sub-main wiring in PVC Conduit:- Wiring for circuit / sub-main wiring along with earth wire with the following sizes of PVC insulated, copper conductor, single core cable in surface/recessed PVC conduit as required. 2x1.5 sq.mm +1x1.5 sqmm earth wire

2x2.5 Sqmm + 1x2.5 sqmm earth wire

4x6 Sqmm + 2x6 sqmm earth wire

Supplying and fixing of the following size of PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.20mm

Supplying and fixing of following modular switch / socket on the existing modular plate & switch box including connection but excluding modular plate etc. as required. 1.24.1 5/6 amps, one way switch

1.24.4 5/6 amps, 3 pin socket outlet

S/F Modular type electronic fan regulator - Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

S/F Modular type blanking plate :- Supplying and fixing modular blanking plate on the existing modular plate & switch excluding modular plate et. As required.

S/F Modular boxes, base & cover plate :- Supplying and fixing following size / modular, G.I box along with modular base & cover plate for modular switches in recess etc as required. 4/5 module (78mm x 140mm x 50mm)

6 module (78mm x 205mm x 50mm)

8/9 module (78mm x 230mm x 60mm)

Supplying and fixing suitable GI box with modular plate and cover in front on surface of in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch. Connection, painting etc. as required (For light plugs to be used in non residential buildings)

S/F power plug point with modular type accessories:- Supply and Fixing GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin, 15/16 amps modular socket outlet and 15/16 amps modular type switch, connection, painting etc as required.

S/F Ceiling Rose:- Supplying and fixing 2 pin ceiling rose on the existing junction box/ wooden block including connection etc as required.

S/F Extra dwon rod :- Providing an fitting extra conduit down rod of 20mm dia 2 x 10cm length wiring with 2 x 1,5mm FR PVC insulated , cpper conductor. Single core cable including panting etc. as required .(Note then 5 ccm length shall be rounded to the nearest 10cm and 5 cm of less shall be ignored

Installation of exhaust fan up to 450mm sweep in the exisiting opnening, including making the hole t suit the size of the above fan, making good the damge, connection, testing , commissioning etc. as required

S/F T.P. MCB DB - Supplying and fixing following way, three pole and netural, sheet MCB ditribution board, 415 volts, on surface/recess, complete with tinned copper busbar, netural busbar, earth bar, din bar, detachable gland plate, interconnections, phosphatized and powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 8 way (4+24), Double door, Horizontal type

Supplying and fixing 6 amps to 32 amps rating, 240 volts, "B" series, miniature circuit breaker suitable for lighting and other loads of following poles in the existing MCB DB complete with connections, testing and commossioning etc. as required. 6/32, single pole, "B" series

S/F DP MCB Isolator - Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required 63 amp

G.I. Earth electrode with salt/charcoal - Earthing with G.I. earth pipe 4.5 mtr. Long, 40mm dia including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal and salt as required

S/L 8 SWG copper wire in ground - Supplying and laying 8 SWG copper wire at 0.50 metre below ground level for conductor earth, including soldering etc. as required

P/F G.I lighting conductor final: Providing and fixing of lighting conductor final, made of 25mm dia 300mm long, G.I. tube having single prong at the top, with 85mm dia 6mm thick G.I base plate including holes, etc. complete as required.

Reverting, sweating and soldering lighting conductor tape:- Reverting, sweating and soldering of copper /GI tape (With another copper / G.I tape, base of the final or any other metallic object ) as required.

P/F G.I lighting conductor tape in horizontal run:- Providing and fixing G.I. tape 20mm x 3 mm thick on parapet surface of wall for lighting conductor as required. (for horizontal run)

P/F G.I lighting conductor tape in vertical run:- Providing and fixing G.I. tape 20mm x 3 mm thick on parapet surface of the wall for lighting conductor as required. (for vertical run)

P/F Testing joint for G.I. lighting conductor:-Providing and fixing testing joint made of 20mm x 3mm thick G.I strip 125mm long. With 4 nos. of G.I bolts. Nuts chuck nuts and spring washers etc. complete as reuired

S.I.T.C of floowing rating reccess/ surface mounted LED round / squre shape Down light luminaria with pressure die cast houshing for single phase supply voltage. Luminari shall be confirm to IS: 10322 part-5/ section-2 or IEC:62722 with all neccssary accessories as required 9.3.2 12W LED Round Down light

Supply Installation, testing and commissioning of follwing size ceiling fan 3 Blades confirming to IS:374:2019 including wiring the down rods of standard length (upto 30cm) with 1.5 sq.mm. FR PVC insulated, copper wire sutable for 230V 50HZ, single phase supply etc. complete as required. 9.4.1 1200mm (48") Ceiling Fan

S.I.T.C of floowing rating surface mounted LED tube light fitting suitable for 230V 50HZ, single phase supply etc. complete as required 9.5.2 20/22 W LED Tube light

Supply of 12" (300 mm) dia Metal exhaust fan etc.

Supply of 16" (400 mm) dia Wall mounted fan etc.

Providing and fixing male ended 15mm dia brass bib cock of approved quality (Wt. not less than 350 gms.) with extra socket all compere as per specification and direction of E/I.

Providing and fixing N.P./C.P. brass/PVC procelain shower rose of 15mm inlet etc. all complete as per specification and direction of E/I. Shower Rose - 125mm

Providing & fixing 15mm size pillar cock C.I. body brass spindle pillar cock of approved quality as per specification & direction of E/I. C.I. body brass spindle

Providing and fixing brass/C.I. stop cock of approved quality all complete as per specification and direction of E/I. 20 mm dia

Providing and fixing G.M. non return valve Horizontal/Vertical type of approved quality as per specification and direction of E/I. Horizontal - 25 mm dia weight not less than 375 gms.

Making holes in walls for laying G.I. pipe and restoring the same after pipe laying as per specification and direction of E/I. 125 mm thick wall

250 mm thick wall

Supplying, fitting and fixing the following items complete with all materials as per specification and direction of E/I.Mirrors of 6mm thick plate glass bevelled edge mirror including C.P brass revolving fitting 3mm ply board and C.P hinges to fix with mirror. 600mm x 450mm size

C.P. brass tower rail 20 mm x 600mm with bracket container

C.P brass liquid soap container

Supplying, fitting and fixing 40 mm high vitreous white glazed earthen E.W.C of P trap of parry Hindustan or any other approved I.S.S make including supplying and fixing 15 liters C.I mosquito proof low down fluhing cistern of approved make with complete fitting with C.I. handle and R.S. or bracket with telescopic flush pipe with brass coupling and plumbers joints spindle stop cock of approved quality weight not less than 450 grams 15 mm P.V.C alkathene pipe 45cm .long with brass coupling at both ends and white/black plastic solid state seal and lead of commander cuckoo or other I.S.S.make with hingers or screws etc. painting pipe and cistern etc .with 2coats of approved paints over a coat of red oxide priming ,all complete as per specification and direction of E/I 10 lit low level PVC cistern

Supplying ,fitting and fixing flat back or angular , lipped front vitreous front vitreous white glazed earthen ware urinal of hindustan parry or any other approved I.S.S. make 5 liters capacity C.I automatic flusing cistern of reliance for any other I.S.S appoved make with all fittings with C.I or R.S brackets , standard size G.I flush pipe with fitting clamps ,15 mm C.I body brass spindle stop cock of approved quality weight not less than 4000 gms , 15 mm PVC /Alkthene pipe 450 mm longwith brass coupling at both ends and doing plumbing joints including painting of exposed part with two coats of approved paints over a priming coat of red oxide , cutting wall and floor ,making good the same etc .all complete as per specification and direction of E/I (a) Flat back or standing corner (600mmx350mm)

Supplying, fitting and fixing viterous white glazed earthen ware wash hand basin of parry or Hindustan or any other I.S.S. approved make supported on pointed C.I. or R.S. brackets 32m C.I. brass waste 15mm dia C.I. body brass spindle stop cock of approved quality of weight not less than 350grms. 32mm P.V.C. waste pipe 750mm long with brass coupling at one end and making plumber joints etc. all complete as per specification and direction of E/I.

Supplying material and labour for constructing ispection chamber of designation class 75B brick size 750mm deep, 600x450mm internal dimension having 250 mm wall thikness in cement mortar (1:6) including 12mm cement plaster (1:4) with punning on inside and cement plaster (1:6) with 600x475mm C.I. Cover with frame (weight not less than 39kg ) alongwith earth work in excavation and 80mm thick P.C.C (1:3:6) in foundation and refilling all complete as per specification and direction of E/I.

Supplying, fitting and fixing C.A.R.W.D. pipe with necessary strips spikes, bends, shoes etc. including cost of carriage, all complete, as per building specification and direction of E/l.75 mm dia

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 25 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.20 mm nominal outer dia Pipes

Providing and fixing PTMT grating of approved quality and colour. 100 mm nominal dia

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Cost of 200mm x 165mm x125 meter deep bore well in all kind of soil and rock in ruler area for installation of pump set with hydrolic DTH Ring machin, all complete including supplying all material, tools, drilling ring, air Compressor and equipment , as fule, lubricant and cost of transortion of Rig machin and other vehicles up to the site From 0-50 meter

From 51-125 meter

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 100 mm nominal size dia

Development of tube well in accordance with IS : 2800 (part I) andIS: 11189, to establish maximum rate of usable water yield withoutsand content (beyond permissible limit), with required capacity aircompressor, running the compressor for required time till well isfully developed, measuring yield of well by "V" notch method or anyother approved method, measuring static level & draw down etc. bystep draw down method, collecting water samples & getting testedin approved laboratory, i/c disinfection of tubewell, all complete,including hire & labour charges of air compressor, tools & accessoriesetc., all as per requirement and direction of Engineer-in-charge

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 200 mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 200 mm clamp

Supply fitting and fixing lowering 40 mm dia G.L. collumn pipe - do - do - all complete job as per direction of E/I.

Supplying 100 mm dia submersible pump sets confirming to 8034 and motor confirming to IS 9283 pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/noryl impeller. Motor suitable for working on 415 + 10, 3HP, 50 Hz, AC supply with cable guard, thurst carbon/fiber bearing to withstand entire hydraulic thurst, water proof winding shall be provided. The pump set shall be suitable for diret coupling Pump shall have suitable outlet as per manufacturers design. Anti thurst stream lined non return valve shall be provided with pump, 3 meter submersible copper conductor cable in single/double run shall be provided with each pump. Submersible pump set 100mm dia (with Polypropylene/Noryl Impeller) up to 20 stages 1.5 HP

Larsen & Toubro 2 HP Starters Control Panel for Submersible Pump

Supplying fitting and fixing 3 crore 4 sqmm Flat copper submersible cable FINOLEX / HEVELS make including all taxes ,royalty etc all complete job as per direction of E/I.

CARRIAGE OF MATERIAL (a) Cement

(b) Steel

(c) Sand

(c) Stone Chips

(c) Stone Metal

(d) Red Brick

(e) Fly Ash Bricks

ADD GST(18%)

LABOUR CESS

Please Enable Macros to View BoQ information