Construction of Canteen inside Fruit and Vegetable Market at Narwal Jammu.

Amount

Demolshing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 mtrs leads. In cement mortoar.

Demolishing cement concrete manually /by mechanical means and disposal of Material within 50 mtrs lead in ( 1:3:6) mix or richar mix.

Demolishing R.C.C.work manually/by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 meters leads.

Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15cm deep and disposal of rubbish, lead upto 50m and lift upto 1.5m in: All kinds of soil.

Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (Not exceeding 1.5 mtr in width) and for shafts, well, cesspits and the like not exceeding 10 sqm on plan, depthupto 1.5 mtr. Including disposal of excavated earth upto 1 mtr from cutting edge, disposed earth is to be levelled and neatly dressed in. All kinds of soil.

Filling available excavated earth (excluding roack) in trenches, plinth, sides of foundation etc. Layers not exceeding 20 cm in depth , consolidating each deposited layer by ramming and watering lead upto 50 mm and lift up 1.5 m.

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - all work up to plinth level in 1:4:8( 1 cement:4 Coarse sand :8 graded stone aggregate 40 mm nomnial size) . Crushed. (Including all carriages and leads).

Providing and laying Hand packed stone filling under floor including supply of stone. (Including all carriages and leads).

Supplying and filling in plinth with fine sand under floors including , watering, ramming consolidating and dressing complete. (Including all carriages and leads).

Provinding and laying in position cement concrete of specified grade excluding the cost of centring and shuttering -All work upto plinth level. 1:3:6 (1 cement :3 coarse sand:6 graded stone aggregate 20 mm nomianl size)Crushed. (Including all carriages and leads).

Making Plinth protection 50 mm thick of cement concrete 1:3:6 ( 1 ceement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) Over 75 mm bed of dry brick ballast 40 mm nominal size well rammed , consolidated and grouted with fine sand including finishing the top smooth. (Including all carriages and leads).

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring , shuttering, finishing and reinforcement -All work upto plinth level. 1:1.5:3 ( 1 cement:1.5 coarse sand :3 graded stone aggregate 20 mm nominla size) Crushed. (Including all carriages and leads).

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring , shuttering, finishing and reinforcement -All work above plinth up to floor V level. 1:1.5:3 ( 1 cement:1.5 coarse sand :3 graded stone aggregate 20 mm nominla size) Crushed. (Including all carriages and leads).

Centering and shuttering including strutting , propping etc and removal of form for:

Foundations , footings , bases of columns etc. for mass concrete.

Suspended floors , roofs, landings , balconies and access platform

Lintels, Beams, plinth Beams, girders bressumers and centilevers.

Edges of slabs and breaks in floors and walls. Under 20 cm wide.

Reinforcement for R.C.C work including straightening , cutting , bending , placing in position and binding all complete . Thermo-Mechanically Treated bars . ( TATA/ SAIL).

Brickwork withcommon burnt clay F.P.S.(non-modular) bricks of class designation 75 in foundation and plinth in cement mortar 1:6 ( 1cement : 6 coarse sand) (Including all carriages and leads).

Brickwork withcommon burnt clay F.P.S.(non-modular) bricks of class designation 75 in super-strucure in cement mortar 1:6 ( 1cement : 6 coarse sand) (Including all carriages and leads).

Providing and fixing gang saw cut mirror polished ( pre moulded and pre polished), machine cut for kitchen platform, vanity counters window sills facias and similar locations of required size of approved shade, colour and texture laid over 20 mm thick bases cement mortar 1:4 ( 1 cement : 4 coarse sand) with joints treated with shite ce,emt , mixed with matching pigment, epoxy touch ups, including rubbing, curing moulding and polishing to edge to give high gloss finish etc. complete at ad levels. Green marble 18 mm thick.

Structural steel work welded in built up sections , trusses and framed work, including cutting, hosting, fixing in position and applying a priming coat of approved steel primer all complete . . ( TATA/ SAIL).

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z. sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required fia, and size including necessary filling up of gaps at junctions i.e at top, bottom and sides with required EPDM rubber/ neoprene- gasket felt etc. Aluminium sections shall be smooth , rust free, straight, mitred and jointed mechanically wherever required including cleat single, Aluminium snap beading for glazing/ panelling C.P. brass/ stainless steel scress, all complete as per architectural drawings and the directions of Engineer-in-charge ( glazing. panelling and dash fasteners to be paid for separately.

For fixed portion: Powder coated aluminium ( minium thickness of powder coated 50 microns)

For shutters of doors, windows and Ventilators including providing and fixing of hinges/pivots and making provision for fittings wherever required including the cost of EPDM rubber/ neoprene gasket required ( nominal fittings shall form part of the item) 10 guage.Powder coated aluminium ( minmum thickness of powder coated 50 microns)

Providing and fixing 12 mm thick pre-laminated particle board flat presses three layers or graded wood particle board ( conforming to IS: 12823 Grade-1 Type-II) in paneling fixed in aluminium doors, window shutters and partitions frames with CP Brass/ stainless screws etc. complete as per architectural drawings and directions of Engineer-In-charge. Pre-alminated particle board with decorative laminated on both sides.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. ( cost of aluminium snap beading shall be paid in basic item) With float glass panes of 4.00 mm thickness ( weight not less than 10.00 kg/sqm)

Providing and fixing anodised aluminium grill ( anodised transparent or dyed to required shade according to IS: 1868 minimum anodic coating of Grade AC 15) of approved design/ pattern, with approved standard section and fixed to the existing windows frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fising and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as epr requirement and direction of Engineer-in-charge ( only weight of grill to be measured for payment)

Providing and fixing double action hydraulic floor spring of approved brand and manufacture, IS: 6315 marked , having brand logo embossed on the body/ plate with double spring mechanism and door weight upto 125 kg for doors including cost of cutting floor, embedding in floors as required and making food the same matching to the existing floor finishing and cover plates with brass pivot and single piece M S sheet cover vos with slide plate etc. complete as per directions of Engineer-in-charge. with stainless steel cover plate minimum 1.25 mm thickness.

Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.00 mm thick, & 2100 mm long with S S screws etc. complete as per directions of Engineer-in-charge . Powder coated minimum thickness 50 micron alumimium tubular handle bar.

Providing and fixing 100 mm brass locks ( best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete.

Providing and fixing aluminium round shape handle of outer dia. 100 mm with S.S screws etc. as per directions of Engineer-in-charge . Powder coated minium thickness 50 Micron aluminium.

Providing and fixing vitrified floor tiles 600x600 mm ( thickness to be specified by the manufactures) of Ist quality conforming of IS: 13755 of SOMANY,KAJARIA, or ORIENT make in colour such as white, lovory, Grey, Fume Red Brown laid on 20 mm thick bed of cement mortar 1:4 ( 1 cement: 4 coarse sand) including pointing the joints with white cement and matching pigment etc. complete. (Including all carriages and leads).

Providing and fixing Ist quality ceramic glazed WALL TILES conforming to IS:13753 of minium thickness 5 mm of approved make like NITCO , ORIENT, SOMANY, KAJARIA in all colour, shades except begundy, bottle green, black of any size as approved by Engineer-in-charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3( 1 cement :3 coarse sand) and jointing with grey cement slurry 3.3 kg sqm including pointing in white cement mixed with pigment of matching shade complete. (Including all carriages and leads).

Cement concrete flooring 1:2:4( 1 cement : 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry, but excluding the cost of noing of steps etc. complete. 40 mm thcik with 20 mm nominal size stone aggregate. Crushed. (Including all carriages and leads).

Making Khurras 45x45cm with average minimum thickness of 5 cm cement concrete 1:2:4( 1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 mx1 mx400 micron, finished with 12 mm cement plaster 1:3( 1 cement : 3 coarse sand ) and a coat of neat cement c, rounding the edges and making and finishing the outlet complete. (Including all carriages and leads).

Providing and fixing on wall face un-plasticised rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion. Single sockted pipes.

75 mm diameter

110 mm diameter

Providing and fixing on wall un-plasticised PVC moulded fittings/accessories for un-plasticised - Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.

110 mm Coupler

Single tee with door 110x110 x110 mm

Bend (110 mm )

Shoe (100 mm )

Providing and fixing unplasticised PVC pipe clips of approved design to unplasticised PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with MS screwed of required length including cutting brick work and fixing in cement mortar 1:4 ( 1 cement : 4 coarse sand) and making good the wall etc. complete. 110mm

12 mm cement plaster of mix 1:6 (1 cement : 6 fine sand) (Including all carriages and leads).

15 mm cement plaster of mix 1:6 ( 1 cement : 6 fine sand) (Including all carriages and leads).

6 mm cement plaster to ceiling of mix 1:3 ( 1 cement : 3 fine sand ) (Including all carriages and leads).

Providing and applying white cement based putty of average thickness 2 mm of approved brand and manufacture, over plastered wall surface to prepare the surface even and smooth complete.

Finshing walls with acrylic smooth exterior paint of required shade o n New work (two or more coats applied @ 1.67 litre/10 sqm over and including base coat of water proofing cement paint applied @ 2.20 kg/10 sqm)

Applying one coat of water thinable cement primer of approved brand and manufacture on wall surfaces.

Wall painting with plastic emulsion paint of approved manufacture to give an even shade . Two or more coats on new work.

Providing and fixing water closet squatting pan ( Indian type WC pan) with 100 mm sand cast iron P or S trap, 10 litre low level white PVC flushing with manually controlled device ( hand lever) conforming to IS : 7231, Parryware/Hindwar/COMMANDER/Cera ( both seat and cistern ) with all fittings and fixtures complete including cutting and making good the walls and floors where required , white vitreous China Orissa Pattern WC pan of size 580x440mm with integral type foot rests.

Providing and fixing white vitreous china flat back half stall urinal basin of 580x380x350mm with white PVC Automatic flushing cistern, Parryware /Hindware/CoMMANDER/ CERA, with fitting , standard size C.P Brass ) with waste fitting as per IS: 2556 CI trap with outlet grating and other coupling in CP Brass including painting of fittings and cutting and making good the walls and floors where required. Range of three half stall urinals with 10 liter white PVC automatic flushing cistern of approved quality.

Providing and fixing white vitreous China wash basin with pedestal including making all connections but excluding the cost of fittings. Flat back wash basin of size 630x450 mm with pedestal.

Providing and fixing P.V.C waste pipe for sink or wash basin including P.V.C waste fittings complete. 32 mm dia. Semi rigid pipe.

Providing and fixing 100 mm stainless steel grating for gully floor or Nahani trap.

Providing and fixing 600x450 mm bevelled edge mirror of superior glass ( of approved quality ) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing PVC terminal guard:

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors: 100 mm inlet and 100 mm outlet .

Providing and fixing PTMT towel ring trapezoidal shape 215mm long, wide with a minimum distance of 37 mm from wall face with concealed fittings arrangements of approved quality and colour weighing not less than 88 gm.

Providing and fixing GI pipes complete with GI fittings and clamps , including cutting and making good the walls. Concealed pipes including painting with anti -corrosive bitumastic paint , cutting chases and making food thw wall.

15 mm dia. Nominal bore

20 mm dia. Nominal bore.

Providing and fixing ball valve ( brass) of approved quality complete . 20 mm nominal bore.

Providing and fixing un-plasticised PVC connection pipe with brass unions 15 mm nominal bore, 45 cm long.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS: 8931. 15 mm nominal bore.

Providing and fixing C P stop cock (concealed ) of standard design and of approved make conforming to I S: 8931 complete . 15 mm nominal bore.

Providing and fixing C.P brass angle valve for basin mixer and gyser points of approved make conforming to I.S : 8931. 15 mm nominal bore.

Providing and fixing PTMT soap dish holder having length of 138 mm, breadth 102 mm, height of 75 mm with concealed fitting arrangements, weighting not less than 106 gms.

Providing and placing on terrace ( at all floor levels) polyethylene water storage tank ISI: 12701 marked including the BIS License No. with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support to tank ( Sintex,Supreme, star, having valid ISI License)- Three layers.( 2x1000 ltr).

Providing, laying and jointing glazed stonewared pipes grade :A: with stiff mixture of cement mortar in the proportion 1:1( 1 cement : 1 fine sand ) including testing of joints etc. complete.150 mm diameter. (Including all carriages and leads).

Providig and fixing C.P. brass close hole basin mixer piller lap of approved quality and make, weighing not less than 1.970 kg. 15 mm nominal bore of standard back type.

Providing and fixing salem stainless steel A ISI-304(18/8) kitchen sink as per I.S 13983 with C.I brackets and stainless steel plug , 40 mm including painting of fittings and brackets cutting and making good the walls , wherever required 610x510 mm bowl depth 200 mm.

Providing and laying cement concrete 1:5:10 ( 1 cement : 5 coarse sand: 10 graded stone aggregate 40 mm nominal size) airound S.W. pipes including bed concrete as per standard design. 150 mm diameter S.W. pipe Crushed. (Including all carriages and leads).

Making soakage pit 2.5 m diameter 3.0 metre deep with 45x45 cm dry brick honey comb shaft with bricks of class designation 75 and S.W drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With F.P.S bricks. (Including all carriages and leads).

Providing and fixing water lift pump complete (1 HP) Make HAVELS, CROMPTON , BAJAJ .

Providing and installation of Ro+UV water Purifier system complete 25-50 leter/Hr ( Eureka Forbe or Kent)

Providing and installation of water Cooler (20 Litre) Complete job. USHA /VOLTAS /BLUE STAR.

Providing and laying intergral cement based water proofing treatment including prepration of surfaces as required for treatmetn of roofs, balconies, terracies etc consisting of following operations. a)applying a slurry coat of neat cement using 2.75kg/sqm of cement admixed with water proofing compound conforming to IS:2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300mm height including cleaning the surface before treatment. b) Laying brick bats with mortar using broken bricks/ Brick Bats 25 mm to 115 mm size with 50% of cemet mortar 1:5 ( 1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS: 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 ( 1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS: 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoing wall upto 300 mm height including rounding of junctions of walls and slabs) c) After two days of proper curing applying a second coat of cement slurry using 2.75kg/sqm of cement admixed with water proofing compound conforming to IS:2645 and approved by Engineer-in-charge. d)Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 ( 1 cement : 4 coarse sand) admixed with water proofing compound conforming to IS: 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finially finishing the surface with trowel with neat cement slurry and making pattern of 300x300mm/sq 3mm deep e) The whole terrace so finished be flooded with water for a miniumum period of wo weeks for curing and for final test . All above operations to be done in order and as directed and specified by Engineer-in-charge with average thickness of 120mm and minium thickness at Khurra as 65mm.

Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size with top and bottom rail of T-iron 40x40 x6 mm with 40mm dia, steel pulleys complete with bolts, nuts locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer.

Providing and fixing tiled False Celling of approved materials of size 595x595 mm in true horizontal level supended on inter locking metal grid of hot dipped galvanised steel sections (galvanised @ 120 gms/sqm both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet spaced at 1200 mm centre to center and cross "T" of size 24x25 mm made of 0.30 mm thick ( minimum) sheet, 1200 mm long spaced between main "T" at 600mm cente to centre to form a grid of 1200x600mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick ( minimum) sheet to be interlocked at middle of the 1200x600 mm pannel to form grids of 600x600 mm and wall angle of size 24x24x0.30mm and laying false celling tiles of approved texture in the grid including , wherever, required cutting/ making , opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main"T" runners to be suspended from celling using GI slotted cleats of size 27x37x25x1.6 mm fixed to celling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvansised butterfly level clips of size 85x30x0.8 mm spaced at 1200 mm center along main T, both exposed width of 24 mm of all T-sections shall be pre- painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge ( the rate is excluding the cost of tiles which will be painf for separately) 12.67.4 12.5 mm thick fully perforated Gypsum Board tile madefrom plasterboard having glass fibre conforming to IS: 2095 part 1 , of size 595x595mm, having perforation of 9.7x9.7mm at 19.4 mm c/c with center borders of 48 mm and the side borders of 30mm, backed with non woven tissue on the back side , haing an NRC ( Noise Rdduction Coefficient) of 0.79, with 50 mm resin bonded glass wool backing.

Providing and fixing of cup Board with ply wood 19 mm thick and finishing with 0.80 mm Mica inside and 1.0mm mica out side. Complete job including cost of all labour and material.

Wiring fot light point/fan point /exhaust fan point/call bell point with 1.5 Sq.mm FRLS PVC insulated copper conductor single core cable in surface /recessed medium class PVC conduit with modular type switch, modular plate suitable size GI Box and earthing the point with 1.5 Sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.Group-A.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel PVC conduit as required. 2x2.5 sq.mm+1x2.5 sq.mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel PVC conduit as required. 2x4 sq.mm+1x4 sq.mm earth wire

Earthing with G.I.earth plate 600 mm x600 mm x6 mm thick including accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm copper strip in 40 mm dia G.I. pipe from earth electrode including connection with brass nut, bolts, spring, washer excavation and re-filling etc, as required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

5/6 A Switch.

15/16 A Switch

3 pin 5/6 A socket outlet

Telephone socket outlet

Providing and fixing Exhaust fan in the exisiting opening including making good the damage, connection, testing, commissioning etc. as required ( 510 mm sweep)

Providing and fixing celing fan 4 Blades 1200 mm (USHA/HAVELS/BAJAJ) complete job.

Providing and fixing LED light 18 watt with brackets ( PHILIPS/ HAVELS/ANCHOR).

Supplying and fixing PVC batten/ angle holder including connections etc. as required.

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 KA,"C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, tesitng and commissioning etc. as required. (Single poles ).

Providing and installation of 5 KVA Transformer (Copper)

Providing and laying main service line with 16 sq. mm wire (Aluminium )

Supply and fixing MCB Distribution Board

providing and installation of Hot water Geyser of 25 litre capacity ( AO SMITH/ JAQUAR)

M/S MOHD ALYASS BHAT GOVT CONTRACTOR

Varun Pandoh

Amit Katyal

Sanjay Kumar Gupta

Zahoor Ahmad Mantoo

M/S VIJAY KUMAR

M/s Mir and Co

Bashir Ahmed Parrey

R.B.Chopra Freighters Pvt. Ltd.

M/s Satish Ganjoo