SPECIAL REPAIR TO BLDG NO P-25 AND 25A (OR LIVING LINE), BI LINE OF 1890 RKT REGT (PINAKA) AT NASIRABAD MIL STN

Amount

Taking down cement or cement lime plaster on stone/brick wall, ceiling incl. Raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for rendering in cement mortar (1:6),15mm thick on stone masonary surfaces finished fair and even complete all as specified and directed.

M&L for rendering in cement mortar (1:4), 15mm thick on stone masonary, external surfaces finished fair & even complete all as specified and directed.

M&L for rendering in cement mortar (1:4) 10mm thick as in ceiling surfaces finished fair and even complete all as specified & directed.

Dubbing out average 10mm thick in CM 1:4 on irregular faces of walls or concrete chajjas etc complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls & providing three coat of white wash complete as specified and directed

M&L for preparation new plastered surfaces of walls and providing two coat of cement base paint complete all as specified and directed.

M&L for preparation old decorated surfaces of walls and providing one coat of cement base paint complete all as specified and directed.

M&L for preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed

M&L for preparation of old plastered surfaces of ceiling and applying two coats of white wash complete all as specified and directed

M&L for preparation of old plastered surfaces of wall and applying two coats of white wash complete all as specified and directed

M&L for preparation of old painted steel surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed

M&L for preparation of new steel surface over 10cm width or grith & applying two coats of synthetic enamel paint of 1st quality over a coat of red oxide primer complete all as spd & directed.

M&L for preparation of old wooden surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M & L for preparation of new wooden surface over 10cm width or girth and applying two coats of synthetic enamel paint of Ist quality over a coat of pink primer complete all as specified and directed.

Demolition of cement concrete (unreinforeced) in floors and paving n.exc 15cm thickness (above or below ground level) complete all as specified and directed.

M&L for glazed ceramic coloured tiles, size 450 mm X 300 mm, 6-7 mm thick on vertical surfaces of wall such as dados, skirting etc set & jointed in neat slurry and pointed in white or colour cement to match over and incl 10 mm thick screed plaster in CM 1:4 complete all as specified and directed

M&L for Non-skid ceramic coloured tiles 7 mm thick (jointless) (sqare/rectangular) area of each tile exceeding 0.11 sqm but n exc 0.18 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and incl screed bed or bedding layer 15 mm thick in CM (1:6) complete all as specified & directed.

M&L for cement 25 mm thick PCC (1:2:4) type B-1 (using 20 mm graded crushed stone aggregate) complete all as specified & directed.

M&L for PCC (1:3:6) type C-1 (using 20mm graded crushed stone aggregate) 50mm thick as in plinth protection finished fair even laid in alternate bays n.exc 2m in length all as specified and directed.

Taking up or down steel tubing and connection 15 mm bore and removing the same from site/keeping aside for reuse complete all as specified and directed.

Ditto all as per item No 21.00 above but 20 mm bore

S & F water tubing 15 mm bore, medium grade, ISI marked galvanized with all fittings and fixed to walls, ceiling or laid in floors complete all as specified and directed.

Ditto all as per item No 23.00 above but 20 mm bore

Fixing only 15mm bore old GI tubing to walls, ceiling or laid on floor including necessary cleanig, cutting, screwing and new fittings such as elbow, Tee, union, socket, reducer etc.

Ditto all as per item No 25.00 above but 20 mm bore

S&F Soap dish any type, fixed to plugs with chromium plated brass screws embedded in the wall complete all as sped & directed.

S&F in repairs Chromium plated bib taps, with capstan heads, screwed down for iron pipe or for brass ferrule & fixed for 15 mm bore pipe complete all as specified & directed.

Dismantling of existing unserviceable water tank of any description capacity exc 250 Ltr but n.exc 500trs capacity each complete all as specified and directed

S&F rotational moulded synthetic (HDPE) water storage tank 500litre capacity hoisted & fixed in position all as specified in SSR Part-I complete all as spd & directed.

S&F ball valves PTMT high pressure with epoxy coated aluminium rod and high density plastic ball, screwed for iron pipe, 20mm bore compete (Minimum weight 210 gm) complete all as spd & directed.

S&F in repairs gun metal globe or gate valve, wheel head cast copper alloy screwed down light pressure with crutch or butterfly handle screwed both ends for iron pipe or for union 25 mm dia, ISI marked complete all as spd & directed.

Taking out old unserviceable water closet (squatt pattern) and S & F Vitreous China, Squatting pan Orissa pattern size 580 x 440mm, white with integral foot rests (excluding flushing cistern and flush pipe ) with Vitreous China ‘P’ or ‘S’ trap, front or back inlet including connection to trap and to flushing pipe, anti syphonage pipe , including PCC (1:2:4) type B-1 for fixing of WC and making good the floor to match the existing complete all as specified and directed.

S&F in repair PVC flushing cistern, with flush out valve ISI marked 10 litre capacity, low level, white with inlet, ball, valve float, handle and 32mm bore PVC flush pipe fixed on walls with and including drilling holes and PVC rawl plugs & connected to pipe all as spd & directed.

Dismantling of ceiling board/lathing any thickness including frame work complete all as specified and directed.

Providing & Fixing false ceiling with Everest Fibre Cement Designer tile Ivory painted (High Pressure Steam Cured) of 4mm thickness (as per IS:14862) of size 595x595 mm and any one of the design (oceanic, lake & hill, cascade or electra) in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 gms, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and 15x32 mm made from 0.30 mm thick sheet, spaced at 1200 mm c/c and cross "T" of size 15x32 mm made of 0.30 mm sheet, 1200mm long spaced between main "T" at 600 mm c/c to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size15x32 mm made of 0.30 mm thick sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 15x20 mm made of 0.30 mm thick sheet and laying false ceiling tiles in the grid including , required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI soffit cleats fixed to existing RCC lintel with dash fasteners, GI adjustable rods of 3mm dia with galvanised Butterfly level clips, spaced at 1200 mm c/c along main T, bottom exposed width of 15mm of all T -sections shall be centra black pre-painted with polyester paint, and having a load bearing capacity of 12 kg/sqm, all complete at all heights as per direction of Engineer-in-charge.

Cutting holes into or through stone walls built in cement lime mortar and walls of cement concrete of superficial area exc 150 sqcm but n exc 400 sqcm and making good in CM 1:3 or cement concrete 1:2:4 type B-1 as required.

S&F rolled mild steel conforming to Fe 290-0 or Fe -330-0 on angle iron section of any size fixed independently with or without connecting plates or welding existing steel or iron surfaces complete all as specified. Note: weight shall be verified by the GE.

S&F in repairs PVC flexible waste pipe of approved quality 32mm bore, 65cm long with one end socketed fixed to waste coupling including one PVC reducer 32mm complete all as specified and directed.

S&F in repairs stop cock/angle cock 15 mm dia cast copper alloy screwed down light pressure with crutch or butterfly handle screwed both ends for iron pipe or for union complete all as spd & directed

S&F in repairs 125mm dia PTMT grating doom shape with centre or side hole (Mini Wt 40 grms) complete all as specified and directed.

S&F CI Nahani/Floor trap 75 mm outlet,with grating including jointing to waste pipe fixed in cement concrete type B1(1:2:4) as in repairs.

Dismantling Asbestos Cement (corrugated, semi corrugated, etc) sheets in roof covering complete all as specified & directed.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified & directed.

S&F factory made solid pannel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rail. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail & bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded. sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, supplying and fixing in the frame at site as per specification and drawings on page 146 of SSR Part - II 2004 complete all as specified and directed.

S&F second class HW 35mm thick, factory made, plain framed, paneled shutter (Three panels) with panels of 9mm thick BWP grade ply wood bonded with high quality liquid phenol formal dehyde synthetic resin adhesive conforming to IS-710. The size of rails & style shall be as per IS-1003 (part-I) kiln seasoned & chemically pressure treated complete all as per specified and directed.

Supply and fixing for 2nd class HW 35 mm thick, gauged and skeleton shutters (Three Panels), factory made open rebated and prepare to receive glass, gauge etc (with sash bar), edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing glass etc. Size of members of shutter shall be as specified in SSR 2009 Part-I, section 8 clause Member shall be kiln seasoned & chemically pressure treated complete all as specified and directed.

S & F Steel window/ ventilator factory made, out of MS hollow section 79mm x 39mmx1.6mm thick frame with double shutter (glazed & wire gauged shutters) made out of Z section using flush butt welding and tennon riveting all as per IS 1038/83, dobby hinges shall be provided to both shutters, Locking arrangements as per sample approval by GE, provided with knob, 10mm MS square bars in grill, Z section handle 100mm size and 150mm long hook & eye welded to frame and shutter, four Nos lugs welded to frame inculding necessary flat iron beading for securing wire gauge etc including holes, cutting holes for hold fast and making good in PCC 1:2:4 type B-1 including synthetic enamel paint over a coat of zinc chrome red oxide primer complete all as specified and directed. Note : Wire mesh and sheet glass shall be measured & paid separately under respective items.

S & F aluminium handle fabricated type, anodised 150mm size conforming to IS complete all as specified and directed.

S & F 300mm long aluminium alloy, anodised, sliding door bolts with hasps, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed.

S&F aluminium, anodised, barrel tower bolt of extruded section, ISI marked, 150 mm long complete all as specified and directed.

S&F mild steel butt hinges, medium weight, cold rolled, ISI marked of size 100 mm, complete all as specified and directed.

S&F Aluminium butt hinges, extruded alu alloy anodised , ISI marked of size 100 mm, complete all as specified and directed.

S & F 125mm single action spring hinges,mild steel with steel wire spring, stove enaelled black, complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.50 sqm and n.exc 4.00 Sqm each and removing from site complete and making good disturbed surfaces of wall in CM (1:3) all as specified and directed.

Taking down unserviceable chowkhats or frame with shutters(without taking off shuters from the frames) of any description n. exc 1.50Sqm and removing from site and making good disturbed surfaces of wall in CM 1:3 complete all as specified & directed. (For windows and ventilators)

M & L for rolled mild steel work angle iron as in door frame (Chowkhats) including provn of 12mm dia deformed bar welded horizontally to bottom of frame confirming to Fe-290 or Fe-330 including preparing back of chowkhat and applying two coats tar and sanding newly tarred surfaces with clean sharp sand complete all as specified and directed. Note: Weight shall be verified by the GE.

S&F in repair fancy type 20mm dia aluminium curtain rods powder coated fixed to bracket complete all as spd & directed.

S&F decorative type knobs with bracket of MS powder coated fixing at end of pelmet rod complete al as spd & directed.

Taking out old un serviceable tubular towel rail & S&F tubular towel rail aluminium anodised 20mm dia 'D' type 60cm long between flanges complete all as sped & directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire & average width of aperture 1.40mm & fixed with wire staples complete all as spd & directed.

Hacking out old, broken glass (any thickness, size, quality or description) from steel or wooden frame n exc 0.50 Sqm each pane complete all as specified and directed.

S&F 4.00 mm thick sheet glass, ordinary / figured quality & glazing with oil putty not exc 0.50 Sqm each pane complete all as spd & directed.

S&F in repairs gun metal globe or gate valve, wheel head cast copper alloy screwed down light pressure with crutch or butterfly handle screwed both ends for iron pipe or for union 20 mm dia, ISI marked complete all as spd & directed.

Demolition of stone/ brick masonry built in cement or cement lime mortar all as specified and directed.

M&L for brick work with flyash bricks straight or curved on plan exc 6m mean radius, built in CM 1:6 complete all as specified and directed.

Ditto all as per item no 66.00 above item, but except brick complete all as specified and directed.

M&L for PCC 1:3:6 type C-1 (using 20 mm graded crushed stone aggregate) as in coping bed block etc including weathering slightly, rounded or chamfered angles and throating as directed and including necessary form work complete all as specified and directed.

M&L for 75 mm thick PCC 1:4:8 type D-2 (Using 40mm graded crushed stone aggregate) as in sub base of floor using 40mm graded crushed stone aggregate complete all as specified and directed.

M&L for 40 mm thick PCC 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate) as in floors complete all as specified and directed.

Taking down existing unservicable treatment of any description including cement plaster any thickness from roof surface cleaning of roof surfaces and and preparing it for further treatment and removing rubbish from the site up to 50 mtrs complete all as specified and directed.

M&L for screeding 10mm thick in CM 1:4 on fair faces of RCC /stone patti roof surface finished fair & even without using extra cement even complete all as spescified and directed.

M&L for five layered roof treatment with APP modified polymeric water proofing membrane, 2 mm thick having centre core not less than 20 micron high molecular high density polythylene film (HMHDPE) protected on both sides with high polymeric asphaltic mix and 20 micron HMHDPE film weight not less than 2.25 Kg/ Sqm applied with bonding material using belown type bitumen conforming to IS-702 Grade 85/25 @ 1.20 Kg/ Sqm over bitumen primer conforming to IS- 3384 @ 0.40 Kg/ Sqm with final coat of bonding bitumen grade 85/25 @ 1.20 Kg/ Sqm over APP membrane with all overlaps complete all as specified and directed.

Material and labour for 40mm thick (average consolidated thickness) PCC (1:2:4) type B-0 using 12.5 mm graded stone aggregate laid in slope as in padding, finished even and smooth on existing slope including provision of 'V' shaped groove 6mm wide and 10mm deep at 1.20 metre interval or parts thereof, both ways on top of PCC padding and filled with mastic bitumen of (1:1) proportion complete all as specified and directed.

M&L for coved fillet in PCC 1:2:4 type B-0 using 12.5mm graded crushed stone aggregate at junction of roof, roof kerbs & parapet wall complete all as specified and directed

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fittings such as switches, ceiling roses, pendants, regulators, sockets etc., removing materials from site and making good disturbed surface of walls, floors etc. complete all as specified and directed.

Disconnecting unserviceable sub main wiring/service connection of any size and including steel conduit and accessories and removing from site and making good the disturbed surfaces complete all as specified and directed

Taking down MCB DB's complete with MCB's/Isolator etc removing materials from site and making good disturbed surface of walls, floors etc. complete all as specified and directed.

M&L for point wiring with 1.5 Sqmm, PVC insulated but unsheathed, stranded copper conductor single core FRLS cable, IS-694 marked, drawn through and including non metallic rigid PVC concealed conduit 20mm dia or higher complete with all PVC conduit accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc./ fittings ISI marked and sunk type pressed steelanodised terminal switch box with bakelite laminated sheet top cover 3mm thick, brass screws and cup washers including 1.5 Sqmm stranded copper conductor PVC insulated green in colour as continous earth conductor connected to common earth and earth dolly with all accessories complete all as specified and directed for:- Make of wire- Polycab/ KEI/ Havells Make of PVC conduit - Polycab/ Finolex/ Legrand-MDS

One light point/bell buzzer point controlled by one, one way switch.

One ceiling fan/exhaust fan point controlled by one, one way switch through regulator.

One three pin 5 Amp socket on same board with other switches.

One 3 pin 5 Amp socket on independent board

Ditto all as per item No. 79.04 here-in-before but with 2.5 Sqmm, for one 5 pin 5/15 Amp socket on independent board including 2.5 Sqmm stranded copper conductor (FRLS) PVC insulated green in colour as continous earth conductor connected to common earth and earth dolly with all accessories complete all as specified and directed.

S&F of sub main wiring with two runs of single core PVC insulated and unsheathed multistranded (FRLS) copper conductor cable of size 6.00 Sqmm LT, 1100 volts grade, drawn through and including 25 mm dia or higher PVC non metallic concealed conduit with accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc. and fittings and one run of 6 sqmm single core multistranded copper conductor cable green colour as earth continuity conductor with suitable lugs made of copper connected to earth dolly. Make of wire- Polycab/ KEI/ Havells Make of PVC conduit - Polycab/ Finolex/ Legrand-MDS

S&F switch piano flush type 5 amps, single pole one way 240 volts complete all as specified and directed. MAKE:-Havells/ SSK/ CONA

S&F Socket outlet 3 Pin 5/6 Amp flush type complete all as specified & directed. MAKE:-Havells/ SSK/ CONA

S&F switch piano flush type 15 amps, single pole one way 240 volts complete all as specified and directed. MAKE:-Havells/ SSK/ CONA

S&F socket out let 2 in 1,multipurpose 3 pin 15/16 Amp flush type ISI marked complete all, as specified & directed. MAKE:-Havells/ SSK/ CONA

S&F bell push piano flush button type 5 Amp complete all as specified and directed. MAKE:-Havells/ SSK/ CONA

S&F bell ding dong type AC 230 volt complete all as specified and directed. MAKE:-Havells/ SSK/ CONA

S&F ceiling fan regulator electronic type rotary four step 120/280 Volts AC. MAKE:-Havells/ SSK/ CONA

S&F ceiling rose surface bakelite 3 terminals 63.5 x 17 mm complete all as specified. MAKE:-Havells/ SSK/ CONA

S&F LED tube light fitting retrofit batten in acrylic linear tube (1x 18 watt),230V for single LED tube light including 1 x 18 W LED retrofit bar professional CW 6500 K cover channel, bipin holders,LED power driver, connector block, etc complete with all accessories internally prewired and including connecting up with twin core twisted flexible copper conductor cable with suitable size. Make: Bajaj Cat Part No BLRB 18W CWc for tube , BLRB - DB 118 for batten , Havells Cat part No PHOTONULTRA1213T8LLSSTL18WLED865SPC (for tube) REGALBATTENT8UPTO1X18WDSBSWH (for batten), Surya Cat no. SLETL-DS 18 PC REFORM for tube, SUB1 18T8LED for batten

S&F of lamp holder PVC/ polycarbonate type with back plate.

S & F bulk head luminarie LED fitting 10 W and acessories complete all as specified and directed. Make: Havells Cat part No LHEOAP7UZ6W010 or equivalent make of Jaquar/ Crompton

Supply and fixing testing and commissioning energy saving street light luminaire 15 watt LED , pressure die cast housing with epoxy powder coated with colour finish and prismatic poly carbonate coverlic cover complete with individual LED lences and complete all as specified and directed. Make - Havells Cat Part No ENDURAPEARLS15WLED757SASYTOPC, Jaquar Cat Part No.LSRT01S016XC or equivalent model of Surya

Supply and fixing street light bracket made of 32 mm GI pipe, 1.2 mtr lenght fixed with two nos of clamp , nut and bolts complete all as specified and directed.

S&F of distribution board single pole & neutral with 200 Amps rated bus bar, for double door IP-42 DB's, made out of sheet steel enclosure, recessed type, factory made powder coated 8 way -240 volts suitable for housing MCB's and isolator's complete in all fixing material/ accessories etc complete all as specified and directed. Make: Legrand/Schneider/Seimens Note: MCB DB and MCB SP/SPN will be of same make.

S&F of MCB distribution board TPN 4 way, 415 volts, double door, with 200 Amps rated bus bar, neutral bar with shrouds, earth bar, IP-43. Make: Legrand (DX-3), Schneider (Acti-09), Siemens ( Betagard)

S&F MCB single pole and neutral 240 Volt 10 KA 32 Amp complete all as specified & directed. Make: Legrand (DX-3), Schneider (Acti-09), Siemens ( Betagard)

S&F MCB single pole 240 volt 10 KA 5 to 32 Amp complete all as specified & directed. Make: Legrand (DX-3), Schneider (Acti-09), Siemens ( Betagard)

S & F of MCB TPN, 415 volt, 63 Amp capacity, 10 KA. Make: Legrand (DX-3), Schneider (Acti-09), Siemens ( Betagard)

Taking down existing ceiling fan, dismantling blades and refixing after cleaning incl conecting up with three core flexible cable from ceiling rose to fan.

Disconnecting and taking down existing electric meter and Refixing the same electric meter, connecting, testing and sealing properly and making good disturbed surface of walls etc complete all as specified and directed.

M&L earthing complete with galvanised steel earth plate electrode 60cmx60cmx6 mm thick buried directly in ground vertically to a depth not less than 2.25m below ground level with top edge of the earth plate at a depth not less than 1.5m below ground level earth plate surrounded by and packed with 15cm thick layer of char coal dust and common salt earth lead GI wire 4.00mm dia by means of volts, nuts, check nuts and washers of galvanised iron and thimble and other end of earth wire connected to main switch board and protected by galvanised iron pipe light grade 15mm bore and water pipe 20mm bore GI light grade with funnel and wire mesh PCC chamber in cement in cement concrete 1:3:6 type C-2 and RCC cover all as specified and shown in elect plate No 3 of SSR Part-I of 2009.

Supply and laying XLPE insulated heavy duty armoured electric cable with stranded aluminium conductor 1100 Volt grade ,cross sectional area 16 Sq mm 4 core complete all as specified and directed.

Supply and fixing tubes light grade GI 40 mm dia with all fitting for cable protection under floor/under road/on wall/on pole,.

Note for all items: All items shall be executed as specified and directed by Engr-in-charge.

kirtiman traders

M/S JAGDISH PRASAD AIRUN

Pioneer Enterprises

M/s SUNIL ENTERPRISES

M/s Jai Jinendra Constructions