SPECIAL REPAIR TO BUILDING NO P-139 AND P - 140 SARDAR MESS AT HQ CHIEF ENGINEER JABALPUR ZONE AND BUILDING NO T-63 AND T-367 AT DEO OFFICE JABALPUR UNDER GE (WEST) JABALPUR

Amount

Excavation in trenches, not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, for laying of pipe, cable etc or n. exc.10 Sqm on plan and n. exc. 1.5m in depth for shafts, cesspits, manholes, pier holes, etc and getting out in any type of soil complete all as specified and directed.

Returning, filling in excavated approved soil, including spreading, levelling, watering and well ramming in layers not exceeding 25cm each complete all as specified and directed.

Removing excavated soil not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

Demolition of cement concrete of any description (unreinforced) in roof , floors (other than ground floors) including removal of debris to out side MD land complete all as specified & directed.

Demolition of cement concrete of any description (unreinforced) in ground floors and paving not exceeding 15 cm thick (below or above ground level) including removal of debris to out side MD land complete all as specified & directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) including removal of debris to out side MD land complete all as specified & directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) complete including removal of debris to out side MD land complete all as specified & directed.

Cutting grooves in brick wall, 75mm wide and 65mm deep and making good by providing reinforcement / wiremesh and PCC 1:2:4 Type B-0 using 12.5 mm graded crushed stone aggregate complete all as specified and directed ( Note : Reinforcement/ wire mesh shall be measured and paid for separately) ..

Providing precast reinforced cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate in cover slabs (for manholes etc), shelves, landings and similar articles with plain faces including necessary moulds and setting in cement mortar 1:4 complete all as specified and directed. Note:- Reinforcement shall be measured & paid for separately under respective item of BOQ.

M & L for precast reinforced cement concrete Type B-1 using 20mm graded crushed stone aggregate in window or door cills, lintels, copings, corbels, brackets, etc.(of any section indicated), with plain fair faces, including chamfers weatherings, throating etc. and setting in cement mortar 1:6 complete with joints to match complete all as specified and directed. ( Note : Reinforcement will be measured and paid for separately)

M&L for 25mm thick PCC (1:2:4) Type B-0 using 12.50 mm graded crushed stone aggregate as in floor sub-base, surface finished even & fair without using extra cement complete all as specified and directed.

M&L for RCC M-20 (Nominal mix) using 20mm graded crushed stone aggregates as in chajjas, parapet, facia etc complete all as specified and directed.

M&L for RCC M-20 (Nominal mix) using 20mm graded crushed stone aggregates as in slab supported on walls, beams and column in floors, roof, landing, balconies canopies deck slab and in shelves complete all as specified and directed.

M&L for PCC 1:2:4 type B1 using 20mm graded crushed stone aggregate as in copings, kerbs, and the like including necessary formwork complete all as specified and directed.

M&L for 100 mm thick cement concrete (1:4:8) Type D-2, using 40mm graded crushed stone aggregate as in sub-base complete all as specified and as directed.

Providing and injecting chemical emulsion for Post Construction Antitermite Treatment Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron. complete all as specified & directed

Providing and injecting chemical emulsion for Post Construction Antitermite Treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per sq.m of the vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc. complete all as specified & directed

Providing and injecting chemical emulsion for Post Construction Antitermite Treatment of soil under existing floors using emulsion @ one litre per hole, 300 mm apart including drilling and plugging 12 mm dia holes with cement mortar 1:2 ( 1 cement : 2 coarse sand) to match the existing floors complete all as specified and directed.

M&L for 5 to 10mm dia mild steel screw bolts (machine made) with hexagonal or square head at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, not exc 5 cm long complete all as specified & directed.

M&L for 5 to 10mm dia mild steel screw bolts (machine made) with hexagonal or square head at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 10 cm but not exceeding 15 cm long complete all as specified & directed.

Dismantling of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facings, dressed stone work and pre-cast concrete articles complete all as specified and directed.

Cutting openings, through brick walls built in cement mortar for door, window and other openings or enlarging existing openings, converting window into door openings, etc. or cutting out defective brick work for under-pinning, including providing, fixing and removing shoring, cleaning and stacking bricks, removing surplus serviceable bricks, hard-core, etc., to store and rubbish, not exc. 50m complete all as specified and directed.

M&L for brick work with sub class 'B' fly ash bricks, straight or curved on plan exc 6m mean radius built in CM (1:6) complete all as specified & directed.

M&L for brick work with sub class 'B' fly ash bricks, straight or curved on plan exc 6m mean radius built in CM (1:4) including flush pointing external faces with the same mortar complete all as specified & directed.

Supply only liquid water proofing compound ISI Marked, of make as approved by GE complete all as specified & directed.

M&L for mils steel galvanised powder coated T-grid frame work of make as approved by GE for suspended false ceiling with size of grid 600 x 600mm consisting of main tee/ runner of size 35 x 25 x 1.3 mm, cross tee of size 25 x 25 x 1.3 mm and wall angle of size 25 x 25x 1.5 mm suspended @ 1.2M c/c both way with and including 4mm dia GI wire with J hook, nuts/bolts, butterfly clips, soffit cleat/ rawl plug etc as per manufacturer's instructions and 8mm thick pre-primed, self embossed, textured designer, water & termite resistant calcium silicate boards for insulation complete all as specified and directed. Make: Armstrong or Ramco Industries or equivalent brand of other Make as approved by GE from list of makes attached with tender documents.

Taking down Chowkhats or frame with shutter (without taking off shutter from the frame) area n.exc 1.50 sqm each and removal complete all as specified & directed.

Taking down Chowkhats or frame with shutter (without taking off shutter from the frame) area exc 1.50 sqm but n.exc 4 sqm each and removal complete all as specified & directed.

S&F powder coated ( minimum thickness of powder coating 50 micron) anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and as directed. (Notes : (i) Unit rate quoted against this item includes for provision of PVC protected sheeting and its removal after fixing the frame work. (ii) Hinges and lugs shall be measured and paid for separately. (iii) Weight of joining cleat shall be added to main frame.)

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/ slabs/ blankets, any thickness, including cover fillets complete all as specified and as directed.

Dismantling timber scantling, unframed, 40 Sqcm and over in section in any position complete all as specified and directed.

S & F anodised powder coated( minimum thickness of powder coating 50 micron) aluminium door shutter aluminium section including necessary jointing ceats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as hinges 150mm long (3 Nos.), handle (2 no.), Lock 06 Lever,Floor Door spring/Stopper heavy duty ISI marked, 5.5mm thick tinted one way glass etc. complete all as specified and directed by Engineer-in-Charge (a) Door frame : 101X44.45X1.5 mm (b) Verticals/style : 83.50X44.45X1.5 mm (c) Bottom, top & Middle Rail : 150X44.45X1.5 mm ( Note : Glazing will be measured and paid for separately under relevant item of this BOQ).

M & L anodised aluminium powder coated( minimum thickness of powder coating 50 micron) sliding windows(four track) with anodised aluminium shutters, both glazed and gauzed with 5.5mm thick tinted glass, stainless steel wire cloth netting(0.36mm nominal dia and averege width of aperture 1.40mm), aluminium grills (Decogrill-DG-916) and fixed including necessary glazing clips, rubber packing, anodized aluminiunm snap beading screws and aluminium fittings of standred size complete all as specified and directed. ( Notes : (i) Glazing and stainless steel wire cloth will be measured and paid for separately under relevant items of this BOQ (ii) Cost of alluminium grill is deemed to be included in the unit rate quoted against this item ).

S & F anodised powder coated( minimum thickness of powder coating 50 micron) aluminium partition including 12 mm thick Designer glass half panel and 18 mm thick pre-laminated particle board both side laminated , fixed type without sash bar, aluminium section including necessary jointing ceats, glazing clips, rubber packing, anodised aluminium snap beading, screws, etc. complete all as specified and directed. ( Note : (i) Glazing and 18mm thick pre-laminated particle board will be measured and paid for separately under relevant items of this BOQ ).

M&L for double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed to aluminium door etc. complete all as specified and directed

M&L for IInd class (Indian Sal, Bijasal, Hollock or Benteak) hardwood plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue, pinned at joints complete all as specified & directed.

M&L for factory made 35mm thick second class (Indian Sal, Bijasal, Hollock or Benteak) hardwood plain, framed, panelled shutter (two or three panels) with lock rail and panel of 9mm thick B.W.P commercial ply or 12mm thick veneered particle board with commercial veneering on both faces; size of rail and stiles as per IS: 1003 (Part-I), kiln seasoned complete all as specified & directed. Note:- Butt hinge will be measured and paid for separately as "Supply only".

M&L for factory made second class (Indian Sal, Bijasal, Hollock or Benteak) hardwood glazed and skeleton shutters 35mm thick, open rebated and prepared to receive glass, gauze, etc divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a) and fitted to chowkats complete all as specified & directed. Notes:- (i) glazing will be measured and paid for separately. (ii) Butt hinge will be measured and paid for separately as "Supply only".

S&F for fabrication of pressed steel cupboard shutters using 1.00 mm thick MS plain sheet and frame 1.25 mm thick, bent to shape, including two coats of synthetic enamel paint on internal surface and two coats hammer tone finish on external surface alongwith locking arrangement, mortice lock handle etc complete all specified and directed.

S&F 35mm thick flush shutters, solid core construction with block board core and plywood face panels commercial type on one face and other side covered with decorative face veneer with liping/frame to match complete all as specified.( Note : The unit rate quoted by the Bidder is deemed to include for provision of suitable blocks for taking mortice locks, latches , or other fittings)

S&F, 1mm thick wood grain printed PVC sheet fixed or laid on to flush doors by using rubber used adhesive, supplying & fixing at site as per specification complete all as specified and directed.

S&F steel ventilator factory made with top hung shutter including hinges, steel peg stay complete all as specified and as directed.

Supply & fix 100mm size butt hinges, medium weight, cold rolled mild steel complete all as specified and directed.

Supply & fix 75mm size butt hinges, medium weight, cold rolled mild steel complete all as specified and directed.

S&F stainless steel hat pegs, solid body, 125mm to 175 mm long complete all as specified and directed

Supply and Fix aluminium handles 150mm size, cast type, anodised complete all as specified & directed.

Supply and fix MS bow handles 150mm size, oval type, stove enamelled black complete all as specified & directed.

Supply and fix 150mm long aluminium anodised barrel tower bolts of extruded section complete all as specified & directed.

Supply and fix 200mm long aluminium anodised barrel tower bolts of extruded section complete all as specified & directed.

Supply and fix 200mm long mild steel barrel tower bolts, stove enamelled black with bright bolt complete all as specified & directed.

Dismantling of AC (corrugated or semi corrugated etc.) sheets including ridges in roof coverings complete all as specified & directed.

Dismantling plain or corrugated steel sheeting any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified & directed.

Dismantling single layer Mangalore pattern or similar tiles in roofing complete complete all as specified & directed.

Supply & fix 150mm long aluminium alloy, anodised sliding door bolts with hasp & staple (bolt type) & fixing clips of sheet, cast or extruded section and fixing bolts & sliding bolts of extruded section or cast aluminium alloy complete all as specified & directed.

S&F mild steel sliding door bolt plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate of 300 mm size complete all as specified and directed.

Supplying & fixing 300mm size ordinary rat tail rod pattern springs of mild steel including roller and roller plate complete all as specified & directed.

M&L for PCC 1:2:4 type B-0 (using 12.50 mm graded crushed stone aggregate) mixed with liquid water proofing compound(WPC) as per manufacturer's instructions, as in padding to maintain proper slope as required for providing polymeric water proofing membrane complete all as specified & directed . ( Note : WPC shall be measured and paid for separately under relevant item of this BOQ)

M&L for 10mm thick rendering over roof surfaces in CM 1:3 with using liquid water proofing compound as per manufacturer's instructions, finished even and smooth without using extra cement complete all as specified & directed. (Note: WPC shall be measured and paid for separately as "Supply Only" under respective item of BOQ. )

M&L for complete removal of existing water proofing treatment from roof and providing water proofing treatment over cleaned and dry roof surface with super thermo APP modified water proofing memberane comprising of the followings for Non-approachable roof :- (i) Properly cleaning and sweeping and washing down with water to remove all dust etc from plastered roof surfaces / walls and filling of crack with sealing compound etc and drying the concrete surfaces (ii) Application of one coat of bituminous based primer conforming to IS: 3384 – 1965 @ 0.3 Kg/Sqm (iii) Laying of one layer of super thermo APP modified water proofing memberane with non polyester reinforcement of Make( M/s STP texsa ltd/Hyperplas memberane of M/S IWL India ltd/MS STPand Tikki Tar ltd) as approved by GE, 3mm thick and minimum weight not less than 3.00Kg/Sqm,laid with gas torch and pasted on roof surfaces with roller. The over laps shall be sealed by flame including vertical surface after cutting necessary grooves and making good with PCC gola 1:2:4 type- B1 etc, and to adhere to bitumen all as per Manufacturer's instructions. (iv) applying two coat of bituminous aluminium paint @ 100gm/ sqm in each coat, over non-accessible roof and blending material such as dry sand @ 0.75Kg/ Sqm over & including a coat of hot air blown bitumen 85/25 grade conforming to IS-702 @ 1.20 kg/sqm over polymeric membrane complete all as specified & directed. ( Note : Quoted unit rate includes side lap and over laps not less than 10 cm as per Manufacturer's technical specifications)

M&L for mild steel TMT bars 8 mm dia as in reinforcement for concrete, cut to length, bent to shape required, including cranking, bending, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for mild steel TMT bars 10 mm dia and over as in reinforcement for concrete, cut to length, bent to shape required, including cranking, bending, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

S&F solid PVC door frame of size 50mm x 47 mm made out of 5 mm plain colour PVC sheet, reinforced with MS square tube, fixing in same opening complete as all as specified and directed.

S&F Factory Made Solid PVC Moulded Door Shutters with wood free EPS 28 to 30 mm thick (stile:), with 2,4 or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm prelam PVC Sheet on back face with particle board core, supplying & fixing in frame at site complete all as specified and as directed

S&F steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

S&F steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

S&F steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded complete all as specified and directed.

Resecuring or easing and adjusting, with out taking down shutters of any description of area n.exc 1.0 sqm each size complete all as specified and directed .

Resecuring or easing and adjusting, with out taking down shutters of any description of area exc 1 sqm but n.exc 2.0 sqm each size complete all as specified and directed .

M&L for mild steel work conforming to Fe-290 Gde -165 as in hand rail, holdfast, half round or other steel section or core for wooden hand rail strait portion, drilled and countersunk for balusters running bars for doors, nosing to steps including embeding in concrete and screwing etc, wind ties for roof including securing bolts, posts & struts in fencing including cutting top to shape as directed, drilling holes, notching for wire, etc; flat iron fillets (for securing wire mesh etc) including all necessary drilling, bolting or riveting etc complete all as specified and directed.

S&F , in repair, stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanised wire staples complete all as specified and as directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanised wire staples complete all as specified and as directed.

S&F 1st class hardwood small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessary' labours; articles not exc 200 cubic cm each complete all as specified and directed.

S & F rubber door seal of good quality , fine finish and easy to install, in any colour and in any size, as approved by GE , complete all as directed.

S&F in repair door closer hydraulically regulated designation No-2 universal type of aluminium body fixed to door frames with screws or by welding suitable for door shutters of 701-805 mm in width & wt between 36-60 kg complete all as specified and directed .

S&F curtain rod fancy type, made out of 25mm dia MS pipe having wall thickness 0.63mm bright finish, colour and pattern as approved by GE, complete all as specified and directed. Make: Aerolux/ MEC/ Vista.

Supply and fix rolled mild steel sections conforming to Fe- 410-W (Gde E-250) quality-A as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails & guides for sliding doors, fixed with angle cleats or other connecting plates etc complete all as specified & directed.

S&F mild steel framed work such as grills, gratings etc with ends of bars shouldered and/ or riveted, or forged into spikes, framed guard bars and similar work conforming to Fe- 290 ( Gde-E-165) complete all as specified and as directed. Note: The unit rate quoted by contractor is deemed to be inclusive of cutting to dead lenth where required, notching, drilling, fitting, rivetting and/or welding or connecting with bolts and nuts (including rivets or bolt and nuts). No claim whatso ever shall be entertained by Govt on this account.

Supply and fix pre-painted galvalume aluminium zinc coating GI based 0.50mm thick(AZ-150)corrugated steel sheet of any colour having minimum tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws/ L or J type or cranked hook/ bolts as complete all as specified & directed. Make: Tata Blue Scope Steel Ltd or M/S Cril Colour Roof India Ltd. or Everest Industries Ltd or equivalent brand of other Make as approved by GE from list of make attached with tender documents.

S&F of pre-painted galvalume aluminium zinc coating GI based 0.50mm thick(AZ-150) plain steel sheet of any colour having tensile strength of 550 Mpa as in ridges, hips, valley gutters, drip and straight flashings (length & girth as fixed) fixed with self tapping screws complete all as specified & directed. Make: Tata Blue Scope Steel Ltd or M/S Cril Colour Roof India Ltd. or equivalent brand of other Make as approved by GE from list of make attached with tender documents.

M&L for mild steel work conforming to Fe-290 Gde -165 as in nosing to steps including embeding in concrete and screwing etc, wind ties for roof including securing bolts, posts & struts in fencing including cutting top to shape as directed, drilling holes, notching for wire, etc; flat iron fillets (for securing wire mesh etc) including all necessary drilling, bolting or riveting etc complete all as specified and directed.

M&L for non-skid joint free coloured ceramic tiles 7-8mm thick (square/ rectangular) area of each tile exc 0.18 Sqm but not exc 0.38 Sqm as in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM (1:6) complete all as specified & directed.

M&L for non-skid joint free coloured ceramic tiles 7-8mm thick (square/ rectangular) area of each tile exc 0.11Sqm but not exc 0.18Sqm as in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM (1:6) complete all as specified & directed.

M&L for non-skid joint free coloured ceramic tiles 7-8mm thick (square/ rectangular) area of each tile exc 0.18 Sqm but not exc 0.38 Sqm as in vertical surfaces such a skirting / dado etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick screed bed in CM (1:4) complete all as specified & directed.

M&L for glazed ceramic coloured tiles 350x250x7mm or 450x350x7mm thick as approved by GE on vertical surfaces such as skirting/ dado, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in CM (1:4) complete all as specified & directed.

M&L for machine cut kota stone slab as in flooring, 18-20mm thick over & including 15mm thick cement screed bed in CM (1:6) laid and jointed with gray cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified & directed.

M&L for cutting or grinding surfaces of old kota stone flooring, skirting, dados etc with carborundum stone by hand or grinding machine, dusting off the surfaces after grinding and finally washing the surface clean with oxalic acid solution and polishing with beeswax polish complete all as specified & directed.

M&L for rubber mould factory made coloured cement concrete chequered tiles with grey cement and pigments 300mm x 300mm x22-25mm thick, set, jointed and pointed in neat cement slurry in floors over and including 15mm thick screed bed in CM 1:6 complete all as specified & directed. Make:- Mehtab Tiles, Indore (MP) or Nitco, Mumbai or Mayur Tiles & Interlocking pavers, Lucknow or Star Tiles & Industries, Ramadevi, Kanpur as approved by GE.

M&L for machine cut kota stone slab as in skirting/ vertical surface, 15-18mm thick over & including 10mm thick rendering in CM (1:4) laid and jointed with gray cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified & directed.

M&L for 75mm thick PCC 1:3:6 type C-2 using 40mm graded crushed stone aggregate as in plinth protection finished even and smooth without using extra cement, forming joints to full depth at every 3M intervals and at every change of direction and filing with bitumen sand mixture 1:3 by weight complete all as specified and directed.

Taking down cement plaster etc on brick walls/ concrete (ceiling) surfaces of any descriptions including racking out joints, hacking for keys, scrubbing down with water and disposal of unserviceable materials to out side of MD land complete all as specified & directed.

M&L for 15mm thick rendering in CM 1:6 on fair faces of wall, finished even and smooth without using extra cement complete all as specified & directed.

M&L for 5mm thick rendering in CM 1:3 as on ceiling, soffit of RCC shelves, surfaces finished even and smooth without using extra cement complete all as specified & directed.

M&L 15 mm thick rendering in CM 1:4 on external surfaces of walls & top surfaces of chajja/roof, mixed with liquid water proofing compound as per Manufacturer's' instructions, surface finished even and smooth without using extra cement complete all as specified & directed. ( Note : Liquid water proofing compound will be measured and paid for separately against relevant item of BoQ)

M&L for preparing old decorated plastered or unplastered surfaces of ceiling by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spot and applying one coat of white wash complete all as specified and as directed.

M&L for preparing new decorated surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

M&L for prepration of new plastered surfaces of walls and applying two coats of cement base paint over & including a coat of cement base primer complete all as specified & directed.

M&L for preparation of old decorated/treated surface of walls including removing existing treatment by rubbing, scrapping, washing and applying two coats of cement base paint over a coat of 2mm thick Birla white putty complete all as specified and directed.

M&L for prepration of old decorated plastered or unplastered surfaces of walls of any description by complete removal of existing treatment and applying one coat of cement base paint on walls complete all as specified and directed.

M&L for prepration of old decorated plastered or unplastered surfaces of walls of any description by complete removal of existing treatment and applying wall care putty @ 1.0Kg/ Sqm and one coat of distemper, oil emulsion, white or tinted, on smooth and even surfaces of wall complete all as specified and directed.

M&L for prepration of old decorated plastered or unplastered surfaces of walls of any description by complete removal of existing treatment and applying wall care putty @ 1.0Kg/ Sqm and two coat of distemper, oil emulsion, white or tinted, on smooth and even surfaces of wall complete all as specified and directed.

M&L for preparing new plastered or unplastered surfaces of walls and applying two coats of distemper, oil emulsion, white or tinted, with and including 2mm thick wall care putty and one coat of appropriate primer complete all as specified and directed.

M&L for preparation of new surfaces of wood or wood based materials of any description over 10 cm width or girth and applying two coat synthetic enamel paint of colour as approved by GE over and including a coat of pink primer complete all as specified & directed.

M&L for preparation of new surfaces of iron/ steel of any description over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer as approved by GE complete all as specified & directed.

M&L for preparation of new surfaces of iron/ steel of any description n exc 10 cm in width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer as approved by GE complete all as specified & directed.

M&L for preparation of old painted surfaces of wood or wood based materials of any description over 10cm width or girth and applying two coat of synthetic enamel paint complete all as specified & directed.

M&L for preparation of old painted surfaces of steel of any description over 10cm width or girth and applying two coat of synthetic enamel paint complete all as specified & directed.

S&F, in repair,3 mm thick sheet glass, ordinary quality and glazing with oil putty /wooden beads in square n. exc 0.5 sqm in each pane complete all as specified and as directed.

S&F 3mm thick figured glass, pin head type and glazing with oil putty or wooden beads in squares n exc 0.50 Sqmtr each pane complete all as specified and directed by Engr-in-charge.

S&F 5.50 mm thick tinted glass, one way , glazing for aluminium door, window and partition etc , n exc 0.50 Sqmtr in each pane complete all as specified and directed by Engr-in-charge.

Dismantling of water tank of any description of capacity exc. 500 litres but not exc. 1000 litres, removing to store or from the site complete all as specified and as directed.

Supply and fix 1000 ltrs capacity rotational moulded polyethylene water storage tank double layered (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified & directed. Make:- Sintex or Tuff or JS Poly Plast or Dhara as approved by GE.

Supply & fix 20mm dia ball valves high pressure of PTMT with epoxy coated aluminium rod and high dencity plastic ball, screwed for iron pipe or brass ferrule complete all as specified & directed. (Note-Min weight should not be less than 210 gms) Make:- PRAYAG SYMET or COMMANDER or equivalent brand of other Make as approved by GE from list of makes attached with tender documents.

Taking up or down steel tubing and connections, including cleaning for refixing or removing to store of size 15mm bore of pipe complete all as specified and as directed.

Taking up or down steel tubing and connections, including cleaning for refixing or removing to store of size 20mm bore of pipe complete all as specified and as directed.

Taking up or down steel tubing and connections, including cleaning for refixing or removing to store of size 40mm bore of pipe complete all as specified and as directed.

Supply & fix 40mm bore medium grade galvanised steel tubes with all fittings and fixed complete to walls and ceilings or laid in floor as sunken spout complete all as specified & directed.

Supply & fix 15mm bore medium grade galvanised steel tubes with all fittings and fixed complete to walls and ceilings or laid in floor complete all as specified & directed.

Supply & fix 20mm bore medium grade galvanised steel tubes with all fittings and fixed complete to walls and ceilings or laid in floor complete all as specified & directed.

Supply & fix in repairs, 20mm bore gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete all as specified and directed. Make:- Leader or Bombay Metal & Alloy Co. or Zoloto or NMC or Vardhman or BIR Jalandhar as approved by GE.

S&F, in repair, Plastic water closet seat, white/cream, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminium hinging device for pedestal pattern WC complete all as specified and as directed.

S&F in repair 15mm bore pillar taps, cast copper alloy, fancy type, chromium plated, screwed down high pressure with or without lettered 'HOT' or 'COLD' with long screwed shanks and fly-nuts, screwed for iron pipes, complete all as specified & directed. Make:- Marc or Zoloto or Plumber or Gem or Seiko or Prayag polymer Pvt Ltd or equivalent brand of other Make as approved by GE from list of makes attached with tender documents.

Supply and fix in repairs, 15mm dia stop valves/ angle cock, cast copper alloy, screwed down high pressure with crutch or butter fly handle, fancy type, chromium plated, with long shank and cup screwed both ends for iron pipe or for unions complete all as specified & directed. Make:- Marc or Zoloto or Plumber or Gem or Seiko or Prayag polymer Pvt Ltd or equivalent brand of other Make as approved by GE from list of makes attached with tender documents.

M&L for stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle , screwed both ends for iron pipe or for unions and fixed , of size 15mm complete all as specified and as directed.

M&L Bib tap, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed, of size 15mm bore complete all as specified and as directed.

S&F in repair, 15mm dia bib cock,cast copper alloy with crutch or butterfly handle, fancy type, chromium plated, long body, screwed down for iron pipe or brass ferrule complete all as specified & directed. Make:- Marc or Zoloto or Plumber or Gem or Seiko or Prayag polymer Pvt Ltd or equivalent brand of other Make as approved by GE from list of makes attached with tender documents.

S&F, in repair, brass chromium plated tubular towel rail 20mm dia 'D' type 60cm long between flanges complete all as specified and directed .

S&F in repair towel rail 600 mm long of PTMT fixed with and including CP brass screw and wooden/plastic cleats complete all as specified & directed. ( Minimum weight 190 gm)

S&F in repair, brass CP shower rose 125mm size, fancy type, suitable for 15mm bore GI pipe with swivel joint as approved by GE complete all as specified and directed.

S&F in repair, 15mm bore PVC connection pipe 450mm long with PTMT nuts complete all as specified & directed.

S&F in repair, 15mm bore PVC connection pipe 600mm long with PTMT nuts complete all as specified & directed.

Supply and Fix PVC connection, Hot and cold type, 15mm size with PTMT nuts of length 450mm .complete all as specified & directed.

Supply & fix in repairs vitreous china white WHB (550 x 400 mm) flat back with CP waste coupling, waste pipe, brackets including cutting for and pinning in ends of brackets complete all as specified and directed. Make:- CERA or PARRYWARE or HINDWARE or equivalent brand of other Make as approved by GE from list of makes attached with tender documents.

Supply & fix, in repair, vitreous china wash down water closet pan (pedestal pattern) white (excluding fixing bolts, flushing cistern and flush pipe) but plastic water closet seat, black/ white, closed pattern with recessed bottom, and cover and mild steel chromium plated or aluminium hinging device, complete all as specified & directed. Make:- CERA or PARRYWARE or HINDWARE or equivalent brand of other Make as approved by GE from list of makes attached with tender documents.

S&F in repair 125mm/ 150mm dia mild steel chromium plated grating fixed on floor trap / nahani trap in Cement Mortar (1:6) , complete all as specified and as directed by Engr-in-charge.

Supply & fix in repairs vitreous china squatting pan, Orissa pattern of size 580x440 mm white, with integral foot rest and PVC 'P' or 'S' trap including connection to trap, and to flush pipe, etc (excluding flushing pipe) and making good to floor complete all as specified & directed. Make:- CERA or PARRYWARE or HINDWARE or equivalent brand of other Make as approved by GE from list of makes attached with tender documents.

Supply and fix in repair 10 ltr capacity PVC valve less syphonic action type flushing cistern low level 'white' with inlet ball valve, float valve & handle Including 32mm bore PVC flush pipe & brackets and brackets fixed to wall complete all as specified & directed. Make:- CERA or PARRYWARE or HINDWARE or equivalent brand of other Make as approved by GE from list of makes attached with tender documents.

Supply and fix in repair 110mm bore PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches or in floors etc complete all as specifed & directed. Make:- Supreme or Kisan Mouldings pvt Ltd or Finolex as approved by GE.

Supply and fix 110mm bore PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches or in floors etc complete all as specifed & directed. Make:- Supreme or Kisan Mouldings pvt Ltd or Finolex as approved by GE.

Supply and fix in repair 75mm bore PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specifed & directed. Make:- Supreme or Kisan Mouldings pvt Ltd or Finolex as approved by GE.

Supply and fix in repair 110mm bore PVC (SWR) pipes, single socketed, in any length with rubber ring joints, fixed to walls/ ceiling with & including necessary clamps of requird size etc complete all as specifed & directed. Make:- Supreme or Kisan Mouldings pvt Ltd or Finolex as approved by GE.

Supply and fix in repair 75mm bore PVC (SWR) pipes, single socketed, in any length with rubber ring joints, fixed to walls/ ceiling with & including necessary clamps of requird size etc complete all as specifed & directed. Make:- Supreme or Kisan Mouldings pvt Ltd or Finolex as approved by GE.

Supply and fix 110mm bore PVC (SWR) bends of any radius, fixed to wall including distance pieces and stack clamps complete all as specified & directed. Make:- Supreme or Kisan Mouldings pvt Ltd or Finolex as approved by GE.

Supply and fix 110mm bore PVC (SWR) bends of any radius provided with access door complete all as specified & directed. Make:- Supreme or Kisan Mouldings pvt Ltd or Finolex as approved by GE.

Supply and fix 75mm bore PVC (SWR) bends of any radius, fixed to wall including distance pieces and stack clamps complete all as specified & directed. Make:- Supreme or Kisan Mouldings pvt Ltd or Finolex as approved by GE.

Supply and fix 75mm bore PVC (SWR) bends of any radius provided with access door complete all as specified & directed. Make:- Supreme or Kisan Mouldings pvt Ltd or Finolex as approved by GE.

S&F in repair 75mm PVC (SWR) multi-floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

Supply & fix PVC (SWR) junction single, (single T), equal or unequal , 75mm bore complete all as specified & directed. Make:- Supreme or Kisan Mouldings pvt Ltd or Finolex as approved by GE.

Supply & fix PVC (SWR) junction single, (double T), equal or unequal , 110mm bore complete all as specified & directed. Make:- Supreme or Kisan Mouldings pvt Ltd or Finolex as approved by GE.

Supply & fix PVC (SWR) junction single, (double T), equal or unequal , 75mm bore complete all as specified & directed. Make:- Supreme or Kisan Mouldings pvt Ltd or Finolex as approved by GE.

S & F PVC (SWR) branch piece 110mm bore, single (single Y) equal or unequal. Make : Finolex/ Kisan/ Supreme/ Prince.

S & F PVC (SWR) branch piece 75mm bore, single (single Y) equal or unequal. Make : Finolex/ Kisan/ Supreme/ Prince.

Supply and fix 110mm bore PVC (SWR) vent cowl complete all as specified & directed. Make:- Supreme or Kisan Mouldings pvt Ltd or Finolex as approved by GE.

Taking down carefully any type of old unserviceable point wiring copper or aluminium conductor (light, fan, socket, bell or power) point complete with fittings such as switches ceiling roses, lamp holders, sockets, fan regulators, call bell, light fittings with PVC conduit surface / concealed or wooden battens including sunken cast iron / pressed steel terminal boxes etc and making good the disturbed surfaces of walls, roof, floors etc to match with the existing surfaces complete all as specified & directed by Engineer-in-Charge.

Taking down old/unserviceable distribution board by disconnection of electric connection carefully SPN DBs/TPN DBs/ Main Switch including old unserviceable MCCBs/ MCBs, Isolators, etc and making good to disturbed surface complete all as specified and directed at site.

Taking down existing old/ unserviceable sub main wiring of any type and description, removal of teak wood batten/ PVC pipe/ PVC casing & caping and making good disturbed surfaces of walls, ceilings etc as per existing complete all as specified and directed.

M&L for point wiring concealed type with 1.50sqmm PVC insulated, unsheathed, single core, multistranded copper conductor FRLS cable 1100 volts grade including 1.5sqmm PVC insulated unsheathed multistranded copper conductor FRLS cable as earth continuity conductor drawn through in and including rigid PVC conduit not less than 20mm dia with its accessories, sunken type pressed steel terminal box made of 1.2mm thick MS sheet/ anodised steel box painted with one coat of red oxide primer including 3.0mm thick ISI marked laminated/ ebonite sheet cover for fixing switches/ socket/ regulators etc including all fixing accessories and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing finish for the one light point/ceiling fan point/exhaust fan point controlled by one no one way switch 5/6 Amps complete all as specified & directed.

M&L for point wiring concealed type with 1.50sqmm PVC insulated, unsheathed, single core, multistranded copper conductor FRLS cable 1100 volts grade including 1.5sqmm PVC insulated unsheathed multistranded copper conductor FRLS cable as earth continuity conductor drawn through in and including rigid PVC conduit not less than 20mm dia with its accessories, sunken type pressed steel terminal box made of 1.2mm thick MS sheet/ anodised steel box painted with one coat of red oxide primer including 3.0mm thick ISI marked laminated/ ebonite sheet cover for fixing switches/ socket/ regulators etc including all fixing accessories and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing finish for Bell point controlled by one 5/6 Amps bell push one way complete all as specified & directed.

M&L for point wiring concealed type with 1.50sqmm PVC insulated, unsheathed, single core, multistranded copper conductor FRLS cable 1100 volts grade including 1.5sqmm PVC insulated unsheathed multistranded copper conductor FRLS cable as earth continuity conductor drawn through in and including rigid PVC conduit not less than 20mm dia with its accessories, sunken type pressed steel terminal box made of 1.2mm thick MS sheet/ anodised steel box painted with one coat of red oxide primer including 3.0mm thick ISI marked laminated/ ebonite sheet cover for fixing switches/ socket/regulators etc including all fixing accessories and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing finish for the one socket out let 3/5 pin, 5/6 Amps controlled by one no one way piano type switch on the same board with other switches complete all as specified & directed.

M&L for point wiring concealed type with 1.50sqmm PVC insulated, unsheathed, single core, multistranded copper conductor FRLS cable 1100 volts grade including 1.5sqmm PVC insulated unsheathed multistranded copper conductor FRLS cable as earth continuity conductor drawn through in and including rigid PVC conduit not less than 20mm dia with its accessories, sunken type pressed steel terminal box made of 1.2mm thick MS sheet/ anodised steel box painted with one coat of red oxide primer including 3.0mm thick ISI marked laminated/ ebonite sheet cover for fixing switches/ socket/regulators etc including all fixing accessories and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing finish for the one socket outlet 3/5 pin, 5/6 Amps controlled by one no one way piano type switch on independent board but not below the switch board of light points in same vertical plane complete all as specified & directed.

M&L for point wiring concealed type with 2.50sqmm PVC insulated, unsheathed, single core, multistranded copper conductor FRLS cable 1100 volts grade including 1.5sqmm PVC insulated unsheathed multistranded copper conductor FRLS cable as earth continuity conductor drawn through in and including rigid PVC conduit not less than 20mm dia with its accessories, sunken type pressed steel terminal box made of 1.2mm thick MS sheet/ anodised steel box painted with one coat of red oxide primer including 3.0mm thick ISI marked laminated/ ebonite sheet cover for fixing switches/ socket/regulators etc including all fixing accessories and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing finish for the one socket out let 3/6 pin, 15/16 Amps controlled by one no one way piano type switch on independent board complete all as specified & directed.

Supply & fix, in replacement, switch piano, flush type single pole, one way 5/6 Amps, 240 volts complete all as specified & directed.

Supply & fix, in replacement, socket outlet 2 in 1, 2 pin 5/6 Amps and 3 pin 5/6 Amps, flush universal type complete all as specified & directed.

Supply & fix modular switch socket outlet multipurpose 3 pin, , 15/16 Amps, and one pin 6 Amp controlled by one switch complete all as specified & directed.

Supply & fix, in replacement, ceiling rose, surface bakelite, 65x50mm surface type, two to three terminals, AC 240 volts complete all as specified & directed.

Supply and fix electrical bell model city ding dong (Ding dong type) AC, 240 Volts complete all as specified & directed. Make:- Anchor or Cona or Plaza as approved by GE.

S & F switch bell push piano type, 6 amp, 230 Volts complete all as specified and directed at site.

S & F modular bell push switches, 6 amp, 230 Volts, 1 module complete all as specified and directed at site.

S & F modular switch 1 way 6 amp, 1 module, 230 Volts complete all as specified and directed at site.

S & F modular switch 1 way 15/16 amp, 1 module, 230 Volts complete all as specified and directed at site.

S & F modular sockets, 6 amp, 3/5 pin combined, two module complete all as specified and directed at site.

S & F modular sockets, 15/16 amp, 5/6 pin combined, two module complete all as specified and directed at site.

S&F lamp holder PVC/Polycarbonate type body, with back plate for batten fittings with and including LED lamp 9 Watt complete all as specified and directed .

Supply & Fixing Smart bright Batten Series, LED luminaire using LED 22 watt 110 Lumens/watt with diffuser which ensures uniform distribution and comfort, batten series features latest LEDs and delivers consistent light output, stable color start Extruded Aluminium housing, Energy efficient, Flicker free start Inbuilt driver unit, Suitable for wall and ceiling mounting using brackets with and including the luminaire testing on completion as per Standard Specification IEC 60598-2-1 / IS: 10322(Parts/Secl), (Make : Philips Cat part No BN 021 LED 22S 6500/4000 PSU GR S1 or Equivalent as approved by GE)

Supply and laying or fixing or passing in trenches/ on pole/ through pipes, 1100 volts grade XLPE insulated, screened PVC bedded, galvanised steel strip or wire armoured, heavy duty electric cable with stranded aluminium conductor of cross section area 25 sqmm, 4 core including jointing materials such as cable glands & lugs etc including taking out old unserviceable cable complete all as specified and as directed. Make:- Havells or Finolex or Gloster or Plaza or Universal as approved by GE.

Supply and laying or fixing or passing in trenches/ on pole/ through pipes, 1100 volts grade XLPE insulated, screened PVC bedded, galvanised steel strip or wire armoured, heavy duty electric cable with stranded aluminium conductor of cross section area 50 sqmm, 3.5 core including jointing materials such as cable glands & lugs etc including taking out old unserviceable cable complete all as specified and as directed. Make:- Havells or Finolex or Gloster or Plaza or Universal as approved by GE.

Drilling (Horizontally) to existing road (maximum 10M wide) suitable for passing GI tubing of dia upto 80mm as required at site complete all as specified and directed. Note:- All necessary T&P required at site for drilling shall be arranged by contractor at his own cost and quoted rate shall be deemed to be included for all these provisions and nothing extra shall be paid on this account.

Supply and fixing/ laying of 40mm bore dia GI pipe light grade in trenches/ under roads/ along pole/ wall for cable protection including all necessary fittings & clamps made out of 25x3mm flat iron etc as required complete all as specified and directed. Make:- JINDAL or ZENITH or TATA as per approved by GE.

S & F Sheet metal enclosure DBs Triple Pole and Neutral 4 way with 200 Amp rated bus bar , double door type with 415 Volts rated IP 43 -IK 09 with acrylic door bus bar complete all as specified and directed

S & F Sheet metal enclosure DBs Single Pole and Neutral 4 way with 200 Amp rated bus bar , double door type with 415 Volts rated IP 43 -IK 09 with acrylic door bus bar complete all as specified and directed

S & F Sheet metal enclosure DBs Single Pole and Neutral 8 way with 200 Amp rated bus bar , double door type with 415 Volts rated IP 43 -IK 09 with acrylic door bus bar complete all as specified and directed

M&L for provision of sub main wiring with four runs of single core FRLS PVC insulated, unsheathed, mutistranded copper conductor cable of size 10.0 sqmm drawn in and including rigid PVC conduit medium grade ISI marked not less than 20mm dia with its accessories, concealed type, including two run of single core FRLS PVC insulated, unsheathed, multistranded copper conductor cable of size 10 sqmm as earth continuity and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing finish complete all as specified & directed. Notes:- (i) Finished sub main wiring with four runs of 10.0 sqmm cable & two run of 10.0 sqmm cable alongwith PVC conduit and its accessories shall be measured and paid as one unit length. (ii) Connections of cables with MCBs or bus bars shall be done through appropriate size brass/copper thimbles. (iii) Colour coding for wiring/ bus bar/ main connection shall be followed .

M&L for provision of sub main wiring with two runs of single core FRLS PVC insulated, unsheathed, mutistranded copper conductor cable of size 6.0 sqmm drawn in and including rigid PVC conduit medium grade ISI marked not less than 20mm dia with its accessories, concealed type, including one run of single core FRLS PVC insulated, unsheathed, multistranded copper conductor cable of size 6 sqmm as earth continuity and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing finish complete all as specified & directed. Notes:- (i) Finished sub main wiring with two runs of 6.0 sqmm cable & one run of 6.0 sqmm cable alongwith PVC conduit and its accessories shall be measured and paid as one unit length. (ii) Connections of cables with MCBs or bus bars shall be done through appropriate size brass/copper thimbles. (iii) Colour coding for wiring/ bus bar/ main connection shall be followed .

M&L for provision of sub main wiring with two runs of single core FRLS PVC insulated, unsheathed, mutistranded copper conductor cable of size 4.0 sqmm drawn in and including rigid PVC conduit medium grade ISI marked not less than 20mm dia with its accessories, concealed type, including one run of single core FRLS PVC insulated, unsheathed, multistranded copper conductor cable of size 4 sqmm as earth continuity and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing finish complete all as specified & directed. Notes:- (i) Finished sub main wiring with two runs of 4.0 sqmm cable & one run of 4 sqmm cable alongwith PVC conduit and its accessories shall be measured and paid as one unit length. (ii) Connections of cables with MCBs or bus bars shall be done through appropriate size brass/copper thimbles. (iii) Colour coding for wiring/ bus bar/ main connection shall be followed .

Taking down existing exhaust/ ceiling fan of any size/ sweep for keeping the safe custody and re-fixing/ re-hanging the same after repair work or as directed and connecting up the same with & including twin twisted copper flexible wire from ceiling rose to exhaust/ ceiling fan complete all as specified & directed.

Supply and fixing in replacement LED T-8 tube light, box type fitting with single side connection polycarbonate LED tube rod 18/20W 4 feet 1 x 18/20 watt MS CRCA box type including rotary type bipin holder and connection with PVC insulalted twin core 23/0.0076 twisted copper cable from ceiling rose to tube light fitting complete all as specified and directed.

Supply and fixing LED Decorative /mirror light fitting 9 watt along with fixture, surface mounted suitable for indoor application , connector block, etc . complete with all accessories internally pre-wired with and including round wood block, connecting up with three core flexible flexible copper conductor cable of suitable size complete all as specified and directed by Engineer in charge. (Make Surya Cat No SLE BT 10 W OR Havells Cat no LUMILINEBS9WLED830SPCWH LUMIN Luker code no LMR 10 or Wipro or equivalent Makes as approved by GE)

Supply & fix, in replacement, LED Security Light Luminaire 25 watt 6000K with .high power LED cool white,CRI 75+ 5% supply voltage 220/240/50 Hz, light engine driver base.pole adapter,powder coated pressure die cast aluminium with heat resistant toughened glass with lens including mounting bracket made out of GI pipe 40 mm dia medium Grade not less than with 1.2 m.long in any shape with 2 nos of pole fitting clamps made out of MS flat , nuts and bolts and painting with aluminium paint complete all as specified and as direced .

Supply & Fixing ceiling light round shape, surface mounted LED 10/12 WATT with dome shape, opal diffuser compelete with fixing all as required and directed at site with and including copper conductor of suitable size & length complete all as specified & directed.

Supply & Fixing Indoor commercial recessed mounted luminaires energy efficient LED luminaire suitable for 600mm x 600mm for grid ceiling light not less than 36 watt with diffusers channel including all accessories, internally pre-wired & making connection to ceiling rose with copper conductor of suitable size & length complete all as specified & directed.

Supply & Fixing VTPN Distribution Box, double door of protection grade IP 43 in fine powder coated, matt finish with best CRCA sheet, fitted with shrouded neutral, insulated pin type copper bus bar, Din rail, earth bar of 4 way, conforming to IS 13032 & 8623 complete with and including MCCB 125 Amps as incoming complete all as specified and directed.

Supply and fix Single phase propeller type Exhaust fan heavy duty AC 230 volts 300 mm sweep, metallic body complete with Metalic louvrers and shutters including electric connection with PVC flexible twin core copper wire from ceiling rose to Exhaust fan, nut & bolt complete all as specified and as directed.

Supply & fix MCB SP, 6 to 40 Amps, 'C' series, 240 volts, 50Hz, 10kA complete all as specified & directed. Make:- ABB/ Legrand/ Siemens/ L&T/ Havells as approved by GE.

S & F, MCB SPN, 40 amps, 240 volts complete all as specified and directed.

S&F , in replacement, single pole and neutral sheet metal enclosures with two pin & earth plug and socket complete with and including one single pole MCB of 20 Amps complete all as specified and as directed.

S & F , in replacement, stepped type electronic fan regulator flush Type on the existing phenolic laminated sheet complete all as specified and directed at site.

S & F fan regulator Modular type step 80/120 watt capacity, of polycarbonite complete all as specified and directed

S & F LED Mirror light fitting 2 ft TL 5 -10/12 watt complete all as specified and directed .Make- Havells Cat part No - LUMILINE PLUS SBS10W LED 865SPCSS or equivalent in PHILIPS ,BAJAJ as approved by GE)

Supplying,installation and testing electric geyser (water storage type) of 25 litres capacity, vertical mounting type, glass lined inner tank, rust proof outer body, 2 KW heating element, suitable for 230V single phase 50 Hz AC supply, BEE Five star Rated, energy efficient, 8kg per sqcm presure withstanding capacity, Class I, ISI Marked, with and including Thermostat with thermal output, heating indicator, multi-functional valve(acts as pressure release valve, non-return valve, expansion valve and vacuum release valve), fixed all as per Manufacturer's instructions, fixed with and including Anchor type/fastener type bolts and nuts(set of 4 bolts of 10mm dia 150 mm long with nuts and washers) into the wall grouted properly to hold the geyser and a making good the disturbed surface complete all as specified and as directed

Supply and fix on-load change over switch of capacity 160 Amps in sheet metal encloser, 4 Pole, 415 Volts to be fixed on wall with FI 32X6mm, nuts, bolts, washers etc complete with all electric connection all as specified and directed. Make:- Havells Cat part No. IHCNFO0160 or equivalent model of make- L&T or Legrand or ABB or Schneider as approved by GE.

Supply,laying & fixing Double Wall Corrugated (DWC) pipes made of High Density Polyethylene (HDPE) with all accessories i.e. all type of joints,Sockets,Elbows,bends and End caps etc.. complete all as specified and as directed , outer dia 50 mm and inner dia 38 mm ( Make :- Telerex/Tirupati or Eqivalent Make as approved by GE)

M&L for earthing complete with galvansided steel earth plate electrode 600x600x6.0mm thick directly burried in the ground (earth pit not less than 2.25M deep below ground level) with top edge of earth plate not less than 1.50M deep below normal ground level, connected to galvanised iron wire 4mm by means of bolts, nuts, check nuts and washers of galvanised iron or steel, 15mm bore GI pipe medium grade including necessary fittings for protection of earthing wire, watering pipe 20mm bore GI medium grade, concrete chamber in PCC (1:4:8) type D-2 using 40 mm grade aggregate, coping shall be in PCC (1:3:6) type C-1 using 20 mm grade aggregate and internal surfaces of concrete chamber shall be given 12mm thick plaster in CM (1:4), funnel with wire gauge of 22 gauge (0.63 mm) 8 mesh per linear including 50mm thick cover of RCC (1:2:4) type B-1 using 20mm grade stone aggregate reinforced with 8mm MS deformed bar @ 75 mm C/C both ways, char coal dust and common salt all as shown in electrical plate No. 3 of SSR Part-I (2009) including all necessary excavation & earth work and removal of surplus soil to a distance n. exc 50M and providing connection points with MS/ GI bolts & washers as required and connection from earth test point to earth electrode with same GI earth wire alongwith protection pipe and testing on completion complete all as specified and directed. Note:- GI wire and protection pipe from earth electrode to test point max upto 7.50M shall be deemed to be included in the unit rates as quoted by the contractor.

Schedule of credit amount of Rs. 1,47,745.00 to be deducted during AOC

SUBHASH CHNADRA RAI

M/s Ram Associates

RAVI ENTERPRISES

Chetna Enterprises