SPL REPAIR/ REPLACEMENT OF WATER PIPE LINE FROM WATER POINT (VSD LINE) TO APS(PW) AND WITHIN SCHOOL AND SPL REPAIR TO ROOF SHEET, FALSE CEILING AND ALLIED WORKS OF BLDG NO H-24 OF MDC MEERUT UNDER GE(U) MEERUT CANTT

Amount

Dismantling pain or corrugated asbestos cement ( corrugated semi-corrugated etc) sheets in roof covering, complete all as specified and directed.

Dismantling wall and ceiling boards ( fibre pulp insullation etc) or insullation boards/ slabs blankets any thickness including cover fillets, complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles and rubbish off the premises, complete all as specified and directed.

Dismantling wrought iron or mild steel work of any desription not other wise provided, complete all as specified and directed.

Taking down steel chowkats or frames not exc. 1.5 Sqm each, with shutters (without taking off shutters from the frame) , complete all as specified and directed.

Taking down steel chowkats or frames exc. 1.5 Sqm and n,exc 4.00 sqm each, with shutters (without taking off shutters from the frame), complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thickness (below or above ground level) and removing rubbish off the MD land.

Demolition brickwork or stone work built in cement mortar inclujding all quoins arches , pillers etc

Taking down cemet plaster including raking out joint hacking for key scribbing down with water, complete all as specified and directed.

Taking down eaves gutters and rain water pipes (any size or pattern) including all fitting heads, shoes bends swan necks etc , including cleaning or refixing or removal to store ( ( measured overall as fixed along the centre line over fitting and accessories)

S&F palin galvanised mild steel 0.80 mm thick sheeting in ridges hips velley gutters , drip and staright flashing ( length and girth as fixed ) with grade of zinc coating 275, complete all as specified and directed.

S&F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc , complete all as specified and directed.

S&F hand rail straight portion drilled and counter sunk for baluster running bars for MS wind tie for roof including securing bolte etc, complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of anycolour having tensile strength of 550 Mpa as in roof covering / clading to wall fixed self tapping screwes/ J or L type cranked hook bolts , complete all as specified and directed.

Ditto as per above item No 14 but plain sheet as in ridge

M&L providing cement concrete type B1, 1:2:4( 20 mm graded crushed stone aggregate ) in roof kerbs or mud stops rounded or chamfered on edge, complete all as specified and directed.

M&L brick work with fly ash bricks ( old size) straight or curved in plan exc 6 m mean radius , built in CM 1:6 , complete all as specified and directed.

M&L 10 mm thick rendering using ready mix plaster bags in cm ( 1:6) on brick/ concrete surfaces of external walls finshed even and fair using water proofing compound as per manufacture complete all as specified Note No1:- Make of ready mixed plaster: Ultratech Readyplast, ACC Accoplast , Birla Aerocon, Note No.2:- Contractor shall bring total bags of ready mix plaster required against the work at site as approved by GE, before commencement of the plastering work

M&L 15 mm thick rendering using ready mix plaster bags in cm ( 1:4) on brick/ concrete surfaces of external walls finshed even and fair using water proofing compound as per manufacture complete all as specified Note No1:- Make of ready mixed plaster: Ultratech Readyplast, ACC Accoplast , Birla Aerocon, Note No.2:- Contractor shall bring total bags of ready mix plaster required against the work at site as approved by GE, before commencement of the plastering work

S&F aluminium anodised sections windows double leaves, double shutter side hung/ top hung comprising glazed and gauged shutters with frame using aluminium anodised extruded sections of size 101.60mmx 38.10mm for frames, 47.62mmx 44.45mm for stiles and rails of shutters having 1.25mm thickness, galzing with 5mm thick tinted sheet glass fixed with and including aluminium anodised snap beadings, neoprene gaskets, shutters fixed to frame with with 75mm size stainless steel butt hinges -02 Nos per leaf, aluminium anodised extruded section 150mm long hanle-01 Nos per leaf, aluminium anodised stay with hook and eye of suitable side -01 Nos per leaf, aluminium anodised Tower bolts-02 Nos per leaf, aluminium anodised deco grill with suitable U frame for fixing grill, stainless steel wire cloth of 0.36mm dia with 1.18mm width of aperture complete all as specified and directed.

S&F aluminium fully glazed door with shutter and frame with one or more rebates made out of JINDAL/INDAL anodised aluminium sections, shutters fixed with floor spring hinge (ISI marked) including jointing cleats for fixing etc complete all as specified with panel of 6 mm thick tinted glass (tint of glass as approved by GE), clips, rubber packing, anodised aluminium snap beading, screws and aluminium fittings all as shown as drg No. CEAA/TD/132 sheet 1/2 and 2.2 except fixed glazing (FG) all as specified and directed.

S & F Aluminium anodised two track sliding windows frame top & sides of size 92 x 31.75 x 1.50mm (section No 20831), bottom of size 92 x 31.75 x 1.50mm (section No 20832) and shutter top & bottom of size 40 x 18 x 1.55mm (section No 20736) and side (handle) of size 40 x 18 x 1.55mm (section No 20738) and lock side shutter frame of size 40 x 18 x 1.45mm (sectio No 20737) and for wire guage shutter of size 18 x 43.50 x 1.35mm (Section No.20791) with locking arrangement including stainless steel wire mesh 0.36 mm nominal dia of wire with 1.40mm average aperture and fixed with stainless steel wire staples and providing 5.5mm thick tinted glass with necessary rubber beading gasket etc including making good to the disturbed surfaces all as specified and as directed.

S&F factory made shutters 35 mm thick plain framed panelled shutter ( Two panel ) with lock rail and panel of 9 mm B.W.P commercial plt or 12 mm veneered particle board with commercila veneering on both faces ,. The size of rail and stile as per IS : 1003 ( part 1) kiln seasoned and chemically pressure treated , complete all as specified and directed.

S&F 150mm size extruded aluminium alloy handles, fabricated type, anodised all as specified and directed.

S&F aluminium, anodised barrel tower bolt of extruded section and fixed 150mm of size all as specified and directed.

S&F 150 mm overall length of cover plate floor door stopper of aluminium alloy body and tougue with hard drawn steel spring , complete all as specified and directed.

Providing & fixing false ceiling at any height with size of tile 600x600x4 mm mineral fiber ceiling tiles E board of type micro looks edge laid on super fine with 15 mm wide T-section flanges with frame work comprises of main runner of size 15x32x3000 mm spaced at 1200 mm centre securing fixed to the structural soffits by approved hangers at 1200 mm maximum centers. Hangers (GI wire of 4.0 mm dia) to be fixed by approved roof plug, level adjusters and screws etc and the last hanger at the end of each main runner not greater than 450 mm from the adjacent wall, Flush fitting 1200 mm long cross tees of size 15x26x1200 mm to be interlocked between main runners at 600 mm centers to form a 1200x600 mm module, cut cross tees longer than that 600 mm to be supported independently. 600x600 mm modules to be formed by fitting 600 mm long flush fitting cross tees of size 15x26x600 mm centrally between the 1200 mm cross tees and with perimeter wall angle of size 19x19x3000 mm secured to wall at 450 mm maximum centers, complete all as specified and directed.

ditto as per above item No. 27 but except perforated board/tiles as in repair .

M&L GI frame work for seamless ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screwas at 450mm centre to centre, intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffits at approxly 900mm centre to centre with GI cleats, GI suspenders and steel expansion fasteners with and including ceiling section of 0.55mm thick having kurled web of 50mm and flange of 26mm each side with lips of 10.5mm fixed to the intermediate channel at 457mm centre to centre all as specified as directed.

M&L Seamless calcium silicate ceiling made out of 1800 x 1200 mm size board of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25 mm long self drilling and tapping screws having phillips head with under head cutter at 200 mm centre to centre, including finshing the joint of face board with specially formulated jointing compound and 48 mm wide fibre tape to provide seam less finish , complete all as specified and directed. (Frame work for ceiling shall be measured and paid separately)

M&L false ceiling corners with designed angular shape of size 100x100mm with POP fixed on 6mm thick fibre board with 20x20mm, 0.55mm thick galvanised sections fixed at intervals not more than 750mm and applying 2 coats of acrylic oil emulsion distemper complete al as specified and directed by Engr-in-Charge.

Material & Labour 12 mm thick prelaminated particle boards, grade 2 quality, interior grade, commercial type fixed with nails to timber frame work as in cupboard shelves, kitchen, cupboards partition etc complete all as specified and directed.

M&L 25 mm thick cement concrete type B-0, 1:2:4 using 12.5mm graded crushed stone aggregate in sub base of floors etc, complete all as specified and directed.

M&L vitrified ceramic dark shade 10 mm thick (sqaure/rectangular) area of each tiles n.exc. 0.36 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match existing tiles and including 15 mm thick screed bed or bedding layer of mortar 1:6 for laying floor finishes complete.

Ditto as per above item but on vertical surfaces over and including 10 mm thick rendering in cm 1 : 4 to receive tiles , complete all as specified and directed.

M&L desiger digital glazed ceramic coloured tiles (Group B II) of size excd 0.11 sqm and not excd 0.18 sqm , 7-8mm thick , on vertical surfaces such as dados skirting and risers to step etc. Set and jointed in neat cement slurry and pointed in coloured cement to match over and incuding 10mm thick screeding in CM 1:4 complete all as specified. ( the quoted rate shall deem to be included for screening and shall not be measured and paid separately ).

Taking down aluminium door with shutters of any size reparing of hings block and plate gasket rubber and replacement of broken glass , hydroulic door closer/ floor spring etc and refixing of door and shutters in the same opening in position complete all as specified and directed

M&L prreparation of surfaces of any description n,exc 10 cm girth including holderbats distance pieces etc with two coat synthetic enamal paint over a coat of red oxide on new steel surfaces

M&L prreparation of surfaces of new steel surfaces any description over 10 cm width or girth including holderbats distance pieces etc with two coat synthetic enamal paint over a coat of red oxide , complete all as specified and directed.

M&L preparation of old painted steel and iron surfaces of any description , not otherwise described ,over 10 cm width or girth and painting one coat with synthetic enamel including cleaning, stopping and rubbing down and removing all drops , , dirts etc, complete all as specified and directed.

M&L preparation of new wooden surfaces of any description , not otherwise described over 10 cm width or girth two coat of synthetic enamel paint over one coat of pink primer complete

M&L preparaing the surfaces of new plastered surfaces of walls by brooming down or steel wire brushing ; scrapping down smoke soot , moulds, moss and efflorescent salts and treating oil and greasy spots, washing, rubbing down and applying two coat of plastic emulsion paint of any tint/shade over a coat of primer and 1 mm thick putty, complete all as specified and directed.

M&L preparation of old decorated distempered surfaces of walls by brooming down or steel wire brushing ; scrapping down smoke soot , moulds, moss and efflorescent salts and treating oil and greasy spots, washing, rubbing down and stopping of distempered and applying one coat of plastic emulsion paint of any tint/shade , complete all as specified and directed.

Complete removal of existing treatment for preparing old decorated plastered or unplastered surfaces of walls by brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots Washing, rubbing down and stopping of distempered and painted surfaces over a coat of putty applying one coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior weather proof paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm , complete all as specified and directed.

M&L preparing new decorated plastered or unplastered surfaces of walls by brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots Washing, rubbing down and stopping of distempered and painted surfaces over a coat of putty applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior weather proof paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm , complete all as specified and directed.

M&L cement concrete 75 mm thick type C1 1:3:6 ( 40 mm graged crushed stone aggregate as in plinth, complete all as specified and directed. protection ) , complete all as specified and directed.

Dismantling/ taking out of 100/110 cast iron, PVC or reinforced concrete pipes jointed in cement mortar in trenches/ walls , complete all as specified and directed.

S&F 110mm dia UPVC ultra drain,SelFit pipes, single socketed, ISI marked, IS-13592 type 'B' in any length, jointed with solvent cement fixed in walls/ trenches and floors , complete all as specified and directed.

S&F UPVC bend equal of any radius without door, ISI marked, IS-14735, jointed with solvent cement for 110mm size pipes , complete all as specified and directed.

S&F 110mm dia UPVC sockets equal, ISI marked, IS-14735, jointed with solvent cement , complete all as specified and directed.

Taking down carefully copper/aluminium point wiring of any type, batten or conduit, (Light, Fan, Socket or power) complete including fittings and making good the disturbed surfaces of walls, ceiling etc in cm and applying two coats of white/colour washing/distempering etc to match the existing surface complete all as directed by Engineer - in- Charge.

Material and labour point wiring with 1.5 sqmm nominal cross sectional area, single core, 1100 Volts grade, stranded, PVC insulated, unsheathed copper conductor cable in and including PVC concealed conduit of 25 mm dia or higher, medium grade complete with and including all PVC conduit accessories/fittings, brass screws, washers etc,alongwith one earth continuity conductor with PVC insulated unsheathed multistranded copper conductor cable of 1.5 sqmm size through and including PVC conduit terminated in modular switch boards including two coats of white/colour washing/ distempering etc to the disturbed surfaces to match the existing for the following. [Note: - Modular switch boards shall be measured and paid separately rate for cutting chasis of walls all are included in the quated rate)

One light point or one fan point or bell point controlled by one switch or bell push

One 3 pin, 05 /06 Amps socket outlet point on independent board controlled by one , one way 05/06 Amps switch

One 3 Pin, 05 /06 Amps socket outlet point on same board controlled by one, one way 5/06 Amps switch

All as per serial item No 52 here in before but with 2.5 Sqmm nominal cross sectional area copper conductor cable for one 15 /16 Amps socket outlet point on independent board with and including continuous earth wire of size 2.5 Sqmm nominal cross sectional area, single core, PVC insulated copper conductor cable, unsheathed and connected to common earth and earth dolly complete all as specified and directed

Supplying and fixing Modular Switch 1 way 6 A, 1 module

Supplying and fixing Modular Switch 1 way 16 A, 1 module

Supplying and fixing Modular Socket 6 A, 2/3 pin combined 2 module

Supplying and fixing Modular Socket 6 A/ 16 A, 2/3 pin combined 2 module

Supplying and fixing Modular Fan step regulator, 120 watt, 2 module

Supplying and fixing Modular Bell push 6A, 1 module

Supplying and fixing Modular Blank plate, 1 module

Supplying and fixing Modular type White cover plate with frame 1 module

Supplying and fixing Modular type White cover plate with frame 2 module

Supplying and fixing Modular type White cover plate with frame 3 module

Supplying and fixing Modular type White cover plate with frame 4 module

Supplying and fixing Modular type White cover plate with frame 6 module

Supplying and fixing Modular type White cover plate with frame 8 module

Supplying and fixing Modular type Metal Flush box 1/2 module

Supplying and fixing Modular type Metal Flush box 3 module

Supplying and fixing Modular type Metal Flush box 4 module

Supplying and fixing Modular type Metal Flush box 6 module

Supplying and fixing Modular type Metal Flush box 8 module

Supply and fixing Bell Multi Music type AC, 230 volts, single pole,compete all as specified and directed.

Supply and fixing of ceiling rose surface bakelite 65x 50mm three terminals complete all as specified and directed.

Supplying and fixing 20 watts Light emitting Diode (LED) tube light fitting wall mounting , indoor decorative aluminium extruded T5 LED battens, Integrated type, AC 230-240V, 50 hz, with PMMA/PC diffuser, 4' long, easy to install Efficacy : 100 lumen/watt, making connections with and including 23/.0076 flexible cord of required length from ceiling rose to connector complete all as specified and directed. Make :- PHILIPS SMART BRIGHT XTRA S4 CAT NO. BN100C LED20S-6500 PSUL120 GR S4 / HAVELLS MODEL LUMLINE SMART CAT NO. LUMLINE SMART 20W LED 865PCWH / HPL CAT NO. HPLBT20WPCIMSCW/BAJAJDAWN PLUS BCLAB 20W LED P S

Supplying and fixing Recess mounted economical LED panel light 2`X2` 36 watt with high quality diffuser for uniform light with 100lm/w housing of pressed aluminium sheeet with complete all as specified and directed. Make:- HPL CAT NO. LEDPN36-E(CW) 1X4/ Crompton MODEL Polaris III CAT NO. LCTLSNE-36-FO-CDL/ PHILIPS CIRRUS SURFACE CAT NO.SM365C LED32-6500 PSU OD WH/HAVELLS MODEL PLANO SURFACE ,PLANOSUR 2X2 PLS 36WLED857S/BAJAJ MODEL SKYLUX GLADDEN CAT NO BZRSQL 36L LED GX CW

Supplying and fixing LED Bulk Head Fitting 10 Watt housing made up corrosion resistant unbreakable PC with high quality diffuser for glare free Aesthetically designed gaskit IP65 protection 100 lm/watt complete all as directed. Make:- CROMPTON MODEL STUD Cat No. LBHP-10-CDL/ PHILIPS MODEL GreenPerform Sleek G2 CAT NO.WT202W LED6S CW PSU S2 PC/HAVELLS MODEL RUGBY GENX 10 CAT NO RUGBYGENXFTS10WLED865SSYMBOPC/BAJAJMODEL WEE PLUS CAT NO BIBWP 10W LED

Supply and fixing round shape down light 12 watt 220 volts 100 LM/W AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete. Make:- CROMPTON MODEL PROXIMA-R CDR-205-12-57-SL-NWH/ PHILIPS MODEL DN296B LED12S-6500 PSE WH S1/BAJAJ MODEL DOVEE CAT NO BZSLO nxt 12L LED WH SD

Supply and fixing lamp holder (Angular/Straight ), insulated body, with back plate for batten fitting complete all as specified and directed

Material and labour sub main wiring with 4 Sqmm nominal cross sectional area, two single core, 1100 Volts grade, stranded, PVC insulated, unsheathed, copper conductor stranded cable with and including continuous earth wire of size 4 Sqmm nominal cross sectional area, single core , PVC insulated, copper conductor stranded cable drawing into and including rigid non metallic PVC conduit of 25 mm dia, medium grade with all conduit accessories/ fittings ,brass screws, washers etc and connected to common earth dolly including all cutting/ chases etc in wall, making good to walls etc including two coats of white/ colour washing/distempering etc to the disturbed surfaces to match the existing complete all as specified and directed including taking out old unserviceable sub main wiring any size.

Material and labour sub main wiring with 6 Sqmm nominal cross sectional area, two single core, 1100 Volts grade, stranded, PVC insulated, unsheathed, copper conductor stranded cable with and including continuous earth wire of size 6.0 Sqmm nominal cross sectional area, single core , PVC insulated, copper conductor stranded cable drawing into and including rigid non metallic PVC concealed conduit of 25 mm dia, medium grade with all conduit accessories/ fittings ,brass screws, washers etc and connected to common earth dolly including all cutting/ chases etc in wall, making good to walls etc including two coats of white/ colour washing/distempering etc to the disturbed surfaces to match the existing complete all as specified and directed including taking out old unserviceable sub main wiring any size.

Material and laboursub main wiring with 10 Sqmm nominal cross sectional area, 4 single core, 1100 Volts grade, stranded, PVC insulated, unsheathed, copper conductor stranded cable with and including continuous earth wire of size 10.0 Sqmm nominal cross sectional area, single core , PVC insulated, copper conductor stranded cable drawing into and including rigid non metallic PVC conduit of 25 mm dia, medium grade with all conduit accessories/ fittings ,brass screws, washers etc and connected to common earth dolly including all cutting/ chases etc in wall, making good to walls etc including two coats of white/ colour washing/distempering etc to the disturbed surfaces to match the existing complete all as specified and directed including taking out old unserviceable sub main wiring any size.

Supply and fixing 240V, 10 KA 'C' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 6 to 32 AMP, in the MCB DB Complete with connection testing and commissioning.

Supply and fixing MCB, SPN, AC, 240 volts of 63 Amps capacity 10KA, 'c' series and making connections with suitable size of copper lugs complete all as specified and directed

Supply and fixing MCB, TPN, 415 volts of 100 Amps capacity 10KA, 'c' series and making connections with suitable size of copper lugs complete all as specified and directed

Supply and fixing MCB DB Box 8 way 200 Amps capacity, 240 volts, Double door, SPN and flush to wall including all cutting etc on wall and making good the disturbed surfaces with painting the wall to match the existing all as specified and directed including taking out old u/s DBs any capacity.

Supply and fixing Sheet Metal Enclosures TPN, 4 way, 415 Volt, Double door for housing MCB's/Isolators and flush to wall including all cutting etc on wall and making good the disturbed surfaces with painting the wall to match the existing all as specified and directed including taking out old u/s DBs any capacity.

Supply and fixing Sheet Metal Enclosures Vertical TPN distribution board with provision of 100/63 Amp MCCB TPN as incomer with necessary internal wiring, MCBs as outgoing , 4 way, 415 Volt, Double door for housing MCB's/Isolators and flush to wall including all cutting etc on wall and making good the disturbed surfaces with painting the wall to match the existing all as specified and directed including taking out old u/s DBs any capacity complete all as specified and directed by the Engr-in-Charge..

Supplying and fixing 10 Sqmm 1100 volts grade heavy duty cable PVC insulated aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, two twin core cable flat or circular complete all as specified and directed.

Supplying and fixing MCCB 4Pole .415 V. fixed type,100 Amps with breaking capacity 16 KA complete al as specified and directed

Supplying and fixing MCB 4 Pole .415 V. fixed type,63 Amps with breaking capacity 10 KA complete al as specified and directed

Supply and fixing Sheet Metal Enclosures with socket plug top and MCBs single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB of 20 Amps capacity 240 volts 'B' series 10KA and making connections complete all as specified and directed including taking out old u/s any capacity.

Earthing complete with galvanised MS earth plate of size 600 x 600 x 6mm thick burried directly in ground not less than 2.25 Mtr below ground level, earth plate paced on all side with charcoal mixed with salt to a thickness of 150 mm in layers, connected by GI earth wire of size 4mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion (GI earth strip will be protected by using 40mm bore GI pipe (light grade) from test point to main board. The earthing includes PCC pit chamber, RCC pit cover and frame, watering pipe 20mm bore, funnel with wire mess with necessary earth work including disposal of surplus soil to a distance not less than 50 Mtr etc complete all as specified and shown in electrical plate No 3 of SSR Part-I.

Supplying, fixing including connecting and testing of energy saving and environment friendly LED street light made out of pressure die cast anodised aluminium with toughened glass cover housing, 30 watts LED to achieve electrical safety class 1, CRI>70 colour temperature 5000k to 6000k with LED working life time >50000 burning hours with integrated constant current electronic driver, nominal volatge 240V, AC,50 Hz, operating voltage range 120-280V, suitable for ambient environmental condition of station, TDH<10%,, Pf >0.95, lumens >80 lm/W, Ingress protection not less than IP65, driver and luminaire shall comply not less than LM-79 or IS 16106 of 2012 including 32mm nominal bore light grade GI pipe brackets made out of 1.50M long GI pipe ,bent to shape and fixed to poles/ walls with Two Nos mild steel flat iron brackets of 40mmx6mm, comprisng 4 Nos mild steel hexogonal head bolts of 12 mm dia, 75 mm long with washers duly painted with two coats of synthetic enamel paint over a coat of red oxide primer, and making connections with cable complete all as specified and directed

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V,size 1400mm with Min Air delivery 245 CFM and service value 6.0 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed.

Taking down of existing unserviceable exhaust fan plastic body 250mm and S and F exhaust fan plastic body 250mm sweep in replacement including making connections with suitable size of copper wire and making good surfaces complete all as specified.

Supply and Fix ceiling fan down rod of MS pipe 15mm bore of length as per site measurement including cutting/threading making tide for fixing providing all necessary check nuts wachers other etc complete.

Taking down and relaying of LT electric cable including laying of old bricks 1100 Volt size up to 95 sqmm size complete all as specified and directed.

M&L sand cushioning to UG cables (8cm deep before laying of cable and 15 cm deep over the cable). Note :- Punned thickness only will be considered for payment.

M&L Bricks for protection cover to under ground cable (with standard size fly ash bricks) with width equal to length of brick laid dry and flat abutting each other complete all as specified and directed.

Excavation in trenches in soft/ loose soil n exec 1.5M wide & n exc 1.5 M deep for laying of GI/CI pipe line & getting out including forming bottom surface all as specified and directed

Excavation in trenches in Hard/ dense soil n exec 1.5M wide & n exc 1.5 M deep for laying of GI/CI pipe line & getting out including forming bottom surface all as specified and directed

Returning filling in trenches including spreading, levelling, watering and well ramming in layer n exc 250 mm thick with soil after the pipe laid & tested complete all as specified and directed

Removing excavated surplus soil to a distance n exc. 50 meter and depositing where directed at a level n exc 1.5 meter above the starting point all as specified and directed

Disconnecting and taking up/ down old existing GI pipe and connection of any description/grade and in any position of trenches/ under floors/ on walls etc including connected fitting/accessaries and fixtures all as directed and specified for the following sizes.

100 mm dia

50 mm dia

25 mm dia

20 mm dia

Taking down old existing sluice valve and new S & F sluice valve of size 100mm with PN-1.6 with stainless steel spindle confirming to IS-14846-2000 doubles flange and including new flanged rubber joints complete necessary nuts bolts with washer and rubber gasket , complete all as specified and directed.

Taking down old existing gate valve and M & L gun metal gate valves with iron wheel bead screwed both ends for iron pipe, including pressure rating upto 25kg/cm2 of size 20 mm dia complete all as specified and directed.

S&F in repair Bib tap 20mm dia. PTMT any color, high pressure screwed for iron pipes and fixed to pipe (minimum weight not less than 90 gms) fixed complete all as specified and directed.

Making bore holes in GI pipe including cutting of pipe where required for making any branch comnnection, repairing branch connection pipe of following size of pipe.

50 mm dia bore

25 mm dia bore

20 mm dia bore

Supply and Fixing including taking down of GI tubing, medium grade, ISI marked complete with all fittings laid in trenches or laid under floors, fixed on wall with and providing clamps etc complete all as specified & directed for the following size:-

50 mm dia bore

25 mm dia bore

20 mm dia bore

M & L for brick masonary valve pit of size 1000 x1000 x 1000 mm (internal dimensions ) including all excavation and earth work in any type of soil and disposal of soil to a distance of not exceeding 50 mtr and depositing all as directed including burnt clay brick work in cement mortar in CM 1:6, 10mm plastering in CM 1.4, PCC 1 : 2: 4 type B-1, 100mm thick at bottom and top of valve pit, and MS sheet 3mm thick fixed with an 40 x 40 x 5 mm angle iron frame on 35 x 35 x 5 mm angle frame work including handle &locking arrangement with 1 No 50 mm lock with two keys( NAVAL/GODREJ/HARRISON) including two coats of syentheic enamel paint over a coal of red oxide primer on steel surface complete all as as specified and directed.

M & L 100mm nominal bore ductile iron pipes with spigot and socketed ends entrifugally cast (spun) class K9 in any length, externally coated with metalic Zinc Coating finished with bituminous paint and internally cement morter linning laid in trenches/fixed to walls or under floors etc. and testing complete all as specified and directed.