Renovation of House no. 12/ Type-IIA in MDU, Rohtak

Amount

Pressed steel sheet frames (chowkats), consisting of 2mm thick steel sheet of the specified section, including iron lugs (hold fasts), iron hings, confirming to PWD specifications, including bolts for fixing stops, locknutch, provision for receiving tower bolts and finished with one coat of ready mixed paint red lead non setting primer of approved quality, fixed in position including the cost of cement concrete 1:3:6 for filling in the frame, and cement concrete 1:3:6 for lugs complete. (a) Door and window frame of size 89mmx50mm with 40mm wide single rebate

Door and window frame of size 127mmx50mm with 40mm wide double rebate

Factory manufactured solid flush door shutters, with block board core as der I.S. No. 1659-1669 bonded with water, proof type danol formaloehyde synthetic resin, hot-press as , conforming to I.S. 2202 part-I and II fixed in position including iron hinges screws chocks/cleats and stops, etc. (Excluding the cost of any fittings other than specified above, but including labour for fixing the same in position) Note:- Commercial veneering with vertical grains or cross bands and face vaneer on both sides comercial facing with laminated core and lipped edges. Duro, Green make 35 mm. Thick

Factory manufactures panelled door or glazed window, shutters of commercial hard wood, such as hillock, champ, chikrassy and chaplash etc. (non coniferous timber other teak, conforming to IS specification No. 1003, kiln seasoned) with 100mm wide vertical styles 150mm wide lock rail 200mm wide bottom rail and 100mm wide other rails, with panels of 15 mm thick , tongued and grooved of commercial hard wood and including cost of iron hings, screws, chocks/cleats, stops, nails etc., complete fixed in position (excluding the cost of any fittings, other than specified above, but including labour for fixing the same in position) 30mm thick

Factory manufactured wire gauge door and window shutters of commercial hard wood such as hollock, champ, chikrassy and chaplash etc. (non coniferous timber other teak, conforming to IS specification No. 1003, kiln seasoned) with 100mm wide vertical styles 150mm wide lock rail 200mm wide bottom rail and wire gauge of 140G or 120G designation including cost of iron hings, screws, chock/cleats, stops nails etc., complete fixed in position (excluding the cost of any fittings, other than specified cost of any fittings, other than specified above, but including labour for fixing the same in position)- 30mm thick

35 mm thick

Supplying and fixing glass panes including special metal sash putty of approved make glass panes 4mm thick, exceeding 40 sq dm areas

Cost of aluminum fittings complete for doors and windows, such as tower bolts, handles, etc. and screws for these fittings (exluding sliding bolt) for single leaf shutter

For double leaf shutter

Providing and fixing sliding bolt with nuts and screws, etc. complete Aluminium size 250 mm X16 mm

Providing and fixing vitrified tiles of size 600 mm x 600 mm of approved make in flooring laid in any pattern as specified over base of 20 mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles. Note:- Tile shall be premium quality (first quality) of reputed manufacturer like SOMANI Make.

Dismantling cement conglomerate/terrazzo floors 25mm to 50mm thick including concrete base.

Providing and fixing vitrified tiles of size 600 mm x 600 mm of approved make in skirting/dedo laid in any pattern as specified over base of 12mm thick cement coarsa sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade to toles.

Providing and fixing anti skid tile 400 x 400 mm or above size of approved make in flooring, laid in any pattern as specified over base of 20mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of tiles. Note : - Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO, KAJARIA, SOMANI, ORIENT, JOHNSONS

Dismantling white or coloured glazed tiles ( to be carefully removed)

Providind and fixing 1st quailty ceramic glazed wall tiles confirming to I.S 15622 (thick ness to be specified by the manufactureer) of appreved make in all colors shades except burgundy, bottle green, black of any size as approved by Ebgineer-InCharge in skirting risers of steps and dados over 12 mm thick bad of cement mortar 1:3 coarse and jointed with grey cement slurry, including pointing in white cement mixed with pigment of matchine shades complete.

Marble stone flooring 20mm to 25mm thick slab including matching grains of marble laid in any pattern as specified over base of 12mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of marble including rubbing and polishing (using marble stone slab of size more than 0.38 sqm each) – Baroda green marble

First class brick work laid in cement sand mortar 1:4 in first storey upto 4 metres abover plinth level.

Wrought iron and mild steel (using angle,flats,square bars,tee,and channels) ladders grills,gratting frames, windowguards, iron doorsopenable or fixed stair case or parapet or any other type of railing, gates and tress guards etc including cost of screws and welding rods or bolds and nuts complete fixed in position

Providing and fixing hard drawn steel wire fabre 75mm x 25mm rectangular mesh with 3.25mm dia wire fixed on steel windows of standard rolled sections with 3mm thick flat iron cover moulding of 12.5mm width, fixed with machine screws welded complete in all respects.

15 mm thick cement plaster 1:4 on the rough side of single of half brick wall.

Dismantling cement conglomerate/terrazo floors 25mm to 50mm thick without concrete base.

Conglomerate floor 50mm thick cement concrete topping 1:2:4. flooring cost of 1.50 mm thick neat cement laid in one operation of the topping .

Providing and applying two coats white cement based putty over plastered surface and grinding the surface smoothwith sand paper to fet an even and smooth finish including cost and carrigr of all material, labour charges, scaffolding, sundries etc. complete(J.K./Brila make)

Distempering with washable oil bound distemper (of approved manufacture) two coats over one priming coat on now work.

Painting two coats with synthetic enamel paint in all shades on old wood work or metallic or plastered or concrete surfaces to give an even shade including rubbing down old paint.

Applying pink primer or aluminium priming coat on wood work including preparation of surface, knotting and stopping, etc.

Extra over item nos. 30.3 to 30.6 for providing and fixing best indian make plastic hygenic seat with lid complete instead of hollow black or white plastic seat and lid. White plastic seat (Solid)

Providing & fixing in position best Indian make (Ordinary ) lavatory suites in vitreous chinaware , R.S. or C.I. Brackets C.P. brass screw down pillar tap with, all fittings best Indian make and complete including making good the walls, floors and painting of fitting etc. WHITE (Iv) Size 550mm x 400mm with one No. tap.

Providing and fixing in position best Indian make C.P brass basin mixer complete instead of one no pillar tap.

Providing and fixing in position 15 mm i/d C.P. brass bib cocks of best quality as required by the Engineer-in-Charge) Bib cock short body

Bib cock

Providing and fixing in position C.P brass stop cocks (as approved by the Engineer-in-charge) 15 mm stop cock Stop cock male and female

Concealed stop cock with flange

Providing and fixing in position best indian make bevelled edge 5.5 mm thick mirror mounted on asbestos sheet ground fixed in position by means of 4 Nos chromium plated brass screws and washers over rubber washers and rawl plug embeded in the wall or chromium plated brass clamps with C.P brass screws ( as required by the Engineer-in-charge) complete including cutting and making good the walls etc. indian make (i) 600mm X450 mm

Providing and fixing in position best indian make shower with 15 or 20 i/d in let C.P brass with revolving joint

Providing and fixing lead inlet connection with brass union for finishoing and warning pipes complete in all respect . (c) 15 mm alkathene pipe inlet connections.

Providing and fixing 1/2'' dia G.I pipe 'B' type Jindal make including fitting and clamps etc. complete to the entire satisfaction of the Engineer-in-charge.

Providing and fixing 3/4'' dia G.I pipe 'B' type Jindal make including fitting and clamps etc. complete to the entire satisfaction of the Engineer-in-charge.

Providing and fixing Orrisa water closet suite complete in all respect as per entire satisfaction of Engineer-in-Charge.

Providing and fixing european water closet suite (EWC) size 360X400X470mm complete in all respect as per entire satisfaction of Engineer-in-Charge.

Providing and fixing C.P jali 5'' ISI dia complete to the entire satisfaction of the Engineer-in-charge.

Providing and fixing C.P Cap ISI complete to the entire satisfaction of the Engineer-in-charge.

Providing and fixing C.P Jet with pipe complete to the entire satisfaction of the Engineer-in-charge.

Providing and fixing stain less steel sink size 450 X 250X 200 mm thick Neelkhant make complete in all respect as per entire satisfaction of Engineer-in-Charge.

Umesh Kumar Chugh Contractor

AMARJEET SINGH