SPL REPAIR TO BLDG NO P/4/1 OF 15 BENGAL BN NCC SURI, PROVN OF STORE ROOM NEAR BLDG NO T-35, SPL REPAIR TO ROOF SHEET AND FALSE CEILING OF BLDG NO A/7/589, PROVN OF JAFFRI WALL IN FRONT OF CERTAIN MD ACCN IN HAMID ENCLAVE, AT PMS

Amount

Taking down cement plaster on brick or stone wall etc. including racking out joints hacking for key scrubbing down with water etc complete all as specified and as directed.

Demolition of PCC in ground floors & pavings n exc 15 cm thickness (below or above ground level) (unreinforced) complete all as specified and directed.

Dismanting of wrought iron or mild steel work af any description not otherwise provided for complete all as specified and as directed by Engineer-in-charge

Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Dismantaling of Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified and as directed by Engineer-in-charge.

Taking down Chowkats or frames not exc. 1.5 sq. m each with shutters (without taking off shutters from the frames) complete all as specified and as directed.

Taking down Shutters of any description n exc 1 sq. m each refixing in same opening complete all as specified and as directed.

Taking up or down 15mm dia GI steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed.

Taking up or down 20mm dia GI steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed.

Taking up or down 25 mm bore steel tubing and connection including cleaning for relaying or removal to store from trenches/wall surfaces complete all as directed.

Taking up or down 40 mm bore steel tubing and connection including cleaning for relaying or removal to store from trenches/wall surfaces complete all as directed.

Excavating in trenches , n.exc 1.5 m wide and n.exc 1.5 m depth for foundation etc or for shafts, wells, cesspits ,manhole pier hole, laying of cables, pipes etc n.exc 10 sqm on plan and n.exc 1.5m in depth and getting out in any kind of soil Note : Manual excavation to be done. During excavation if any damage occured to existing cable any type/ water pipe line, it will be contractor responsibilty to get it repair and make functional by providing jointing kit etc without any extra cost. Contractor has to repair it within 24 hrs so that essential service can not be effected due to such damage.If contractor fails to repair it within 24 hrs penalty @ Rs 500/- will be charged to contractor. In this GE decision will be final, conclusive and binding.

All as per item No 12.00 here-in-before but depth exc 1.50 m but n.exc 3.00 mtr complete all as specified and as directed.

Returning, filling, including spreading, leveling, watering and well ramming in layers not exc. 25cmin soft/loose soil complete all as specified and as directed.

Removal of excavated soil to a distance not exc 50 m and depositing where directed at a level not exc 1.5 mtr above the starting point complete all as directed.

M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified and directed.

M&L for paving with mix of flyash, clinker & stone dust in the proportion of 1:3:6 (ie 10% fly ash, 30% clinker and 60 % stone dust) laying in layers n. exc 10cm thick, watering, ramming and compacted with vibratory/ power roller 8 to 12 tonn roller to required camber and gradient complete all as specified and as directed by Engr-in-Charge

M&L for Hardcore using Broken stone or boulders of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface, all as specified and as directed.

M&L for Plain cement concrete type D2 1:4:8 (using 40 mm graded crushed stone aggregate) as in foundation and mass filling, all as specified and as directed.

M&L for RCC (Design mix), M-25 (using 20 mm graded crushed stone aggregate) in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete, complete all as specified and as directed.

M&L RCC (Design mix), M-25 (using 20 mm graded crushed stone aggregate) as in columns, pillars, piers,posts and struts , complete all as specified and as directed.

M&L for RCC (Design mix), M-25 (using 20 mm graded crushed stone aggregate), in Beams, cantilevers, and lintels, complete all as specified and as directed.

M&L for RCC(Design mix), M-25 (using 20 mm graded crushed stone aggregate), in chajja, complete all as specified and as directed.

M&L for RCC(Design mix), M-25 (using 20 mm graded crushed stone aggregate), in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and as directed.

M&L PCC(1:3:6) type C1 (20 mm graded crushed stone aggregate) as in bed blocks for hold fast including necesssary formwork, kerb stones etc complete.

M&L for PCC 1:2:4 type B1 (20mm graded crushed stone aggregate) as in coping including use and removal of necessary formwork all as specified and directed by Engr-in-Charge.

M&L for Providing precast cement concrete type B-0 1:2:4 with (using 12.5 mm graded crushed stone aggregate) louvres and jallies, 25mm thick (measured solid), including all mouldings but excluding frame, set in CM 1:4 complete all as specified and directed by Engr-in-Charge.

M&L for Steel Centering and shuttering including strutting, propping etc. and removal of form to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter

M&L for Steel Centering and shuttering including strutting, propping etc. and removal of form to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. for fair finished surface of concrete, complete all as specified and directed.

M&L for Steel Centering and shuttering including strutting, propping etc. and removal of form to sides of pillars, posts, struts, piers, columns and stanchions for fair finished surface of concrete Complete all as specified and directed.

M&L for Steel Centering and shuttering including strutting, propping etc. and removal of form to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping), for fair finished surface of concrete, all as specified and as directed.

M&L for Formwork to edges concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and directed.

Mild TMT steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed

Mild TMT steel bars 6 to 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed

S&F TMT reinforcement bar, conforming to Fe-500, 5mm dia and upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends as binding with and including mild steel wire (Annealed) not less than 0.9mm dia or securing with clips all as specified.

S&F Mild steel flat iron as in hold fast clamps and similar small articles conforming to Fe-290,Gde E-165, complete all as specified and as directed.

M&L for brick work with fly ash bricks old size, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6, all as specified and as directed.

M&L for damp proof course 40mm thick M-20 (Nominal Mix) using 12.5mm graded crushed stone aggregate with water proofing compound conforming to IS-2645 liquid grade as per manufacturer’s instructions with and including polythene film 200 micron over and including 85/25 grade Industrial bitumen (IS-702 : 1988) @ 1.5 kg/sqm blended with the dry sand @ 0.05 cubic meter/ sqm. complete all as specified and directed.

Cutting chases in brick walls, pinning in, making good to facings where required and pointing in cement mortar 1:3 and cutting chases for concealed water tubing and making good of groves for concealed GI tube, cutting not exc 10cm girth complete all as specified and as directed.

M&L for Rendering 15 mm thick cement plaster in CM 1:4 on fair faces of brick/concrete surfaces finished fair and even, mixed wth water proofing compound admixture (if directed) as per manufacturer's instruction, complete all as specified and directed. Note :- WPC will measuered and paid separatly under relevant item of schedule.

M&L for rendering 10 mm thick in cement sand mortar 1:3 on other than fair faces of brick work or concrete surfaces, finished fair and even complete all as specified.

M&L for rendering 5 mm thick on fair faces of concrete surfaces as in ceiling, finished even and smooth without using extra cement, on walls in cement mortar 1:6, complete all as specified and as directed.

Supply only liquid WPC, ISI marked complete all as specified and as directed

M&L for repair to crack portion with jacktting technique, taking down existing plaster upto brick wall surface of min 200 mm wide, cleaning to loose particles on surface of brick work along the length of crack and filling the gap/ crack area with PCC 1:1.5:3 type A0 using 12.5mm aggregate both side of the wall surface fixed with, drilling holes 10mm dia on either side of the crack by means of drilling machine through out the full width of the wall @25 cm c/c and insert 8/10 mm dia rod in the drilled holes, welded with horizontal rod to with hold the welded mesh and applying grit plaster 1:1:2 using 4 mm and down aggregate finished even and smooth without using extra cement, complete all as specified and directed. (Note: Reinforcement and welded mesh will be measured and paid separately)

M&L for grading roof in cement mortar 1:3, 25mm thick in edge and 50mm thick in ridge including necessary curing complete all as specified in SSR Part I clause No 11.42.2

M & L for providing water proofing treatment with a layer of APP based polymeric membrane, 3 mm thick (minimum), weighing not less than 3.60 kg/Sqm reinforced with polymer non woven fabric (weighing not less than 160 gm/ Sqm) shall be applied over one coat of cold bituminious primer @ 0.40 ltr/ Sqm ( membrane shall be laid using butane torch and sealing all joints etc, complete all as specified and directed .( Note: The overlaps shall be of minimum 75 mm on longitudinal direction and 100 mm on transverse direction) complete all as specified and directed.

M&L for one coat aluminium paint over APP membrane, over 10cm in width or girth,not otherwise described complete all as specified.

S&F 2nd class hardwood Plain well seasoned, solid, straight, chowkats & frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and as directed.

S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying and fixing in opening as per specification and drawing complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet trip of 20mm with stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, supplying and fixing in the frame at site as per specification and drawing complete all as specified and directed.

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators frame and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per the directions of Engineer-in-Charge

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-chargeher for openable/sliding shuttters) including all necessary fittings as directed

S&F Chimney bars (straight or camber); bearing bars; ton-gues or water bars for window frames; window guard bars, plain let in & fixed independently in wooden frames L or T section support for shelves etc., & similar articles conforming to Fe 290-0 Gde E-165 complete all as specified and as directed.

S&F pressed steel door frames of size 125X60mm, of doors with one or more rebates including necessary fixing lugs, hinges(03 Nos of 100 mm size and 01 No of 50 mm size medium weight coled rolled mild steel butt hinges per leaf ) lock strike plate, etc incl one shop coat of priming complete all as specified and directed(Th 1.60 mm)

S&F Framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe-290, Gde-E-165 the grill shall be inseted in the wall surface including necessary drilling and grouting with cement etc, complete all as specified and directed.

S&F for Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete.

S&F Steel windows with side hung shutters including projecting type hinges with steel handle, & steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and as directed.

M & L for pre-painted hot-dip aluminium-zinc alloy metallic coated of any profile steel sheet corresponding to IS 15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ150, 0.50 mm thick, of an approved colour and having yield strength of 550 MPa as in roof covering fixed with self tapping screws as specified up to anyheight including all necessary scaffolding and safety measures complete all as specified and directed

M & L for pre-painted hot-dip aluminium-zinc alloy metallic coated plain steel sheet as per IS 15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ150, 0.50 mm thick, of an approved colour and having yield strength of 550 MPa as in ridge/ valley/ gutter fixed with self tapping screws as specified any height Mtr height including all necessary scaffolding and safety measures complete all as specified and directed

S&F 605mm x 605mm Anodised aluminium snap grid frame work for false ceiling with all necessary aluminum angle & Tee arrangement with and incl fixing cleats screws and Hangers 4 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long and 6mm thick 'E' board (non asbestos fibre) plain building boards fixed in aluminum frame work in ceiling flat or sloping with screws etc including Dismantling of wall or ceilling boards of any thickness including cover fillets complete all as specifiedby Engineer-in-charge.

S&F 100 mm butt hinges,extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21,complete all as specified and directed.

S&F 75 mm butt hinges,extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21,complete all as specified and directed.

S&F aluminium anodised 150 mm barrel tower bolts of extruded section complete all as specified and directed.

S&F 150 mm long extruded aluminium alloy handles,fabricated type, anodised complete all as specified and directed.

S&F Aluminium alloy, anodised, sliding door bolt 300mm long with hasp, staple (bolt type) & fixing clips of sheet, cast or extruded sections & fixing bolts & sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed.

S&F in repairs Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed.

S&F Floor door stopper of brass body 140 mm and tongue, anodised, with hard drawn steel spring & end rubber shoes, fixed in floor, complete all as specified and as directed.

M & L 75 mm thick cement concrete type B2 ,for PCC (1:2:4) using 40 mm graded crushed stone aggregate used as in sub base, sub floor/pavings and complete all as specified and as directed.

M & L 75 mm thick cement concrete type D2 ,for PCC (1:4:8) using 40 mm graded crushed stone aggregate used as in sub base, sub floor/pavings and complete all as specified and as directed.

M & L 100 mm thick cement concrete type B1 ,for PCC (1:2:4) using 20 mm graded crushed stone aggregate used as in sub base, sub floor/pavings and complete all as specified and as directed.

M & L 100 mm thick cement concrete type B2 ,for PCC (1:2:4) using 40 mm graded crushed stone aggregate used as in sub base, sub floor/pavings and complete all as specified and as directed.

M&L Non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06sqm but not exceeding 0.11 sqm in floors laid over 15mm thick 1:6 cement mortar screed bed etc. set and jointed in neat cement slurry and pointed in white of coloured cement to match complete all as specified and directed.

M&L Non Skid ceramic coloured tiles 7 to 8mm thick (squares/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors/skirting etc. laid over 15mm thick 1:6 cement mortar screed bed set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L Glazed ceramic coloured tiles in vertical surface 450X 300X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match all complete all as specified and directed.

M&L for 16 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking plat?forms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, including screed bed of 20mm thick in 1:4 cement mortar, complete all as specified and as directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, granite/kota stone and other similar situations incl polishing, complete all as specified and directed.

M&L for Machine cut kota stone slab flooring 20-25mm thick over 20cm thick cement screed bed in CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

M&L for Machine cut kota stone 20-25mm thick as in skirting set and jointed in neat cement slurry over and including 10 mm thick backing plaster in CM 1:3 finished even and rough complete all as specified and as directed.

M&L for 75 mm thick cement concrete M10 (Nominal Mix) with 40mm graded stone crushed aggregate finished even and fair laid to a slope of 1 in 12, laid in alternate bays, each bay not exceeding 3 m length with joint filled with bituminous mastic filling comprising a mixture of 1 part of heated Industrial bitumen 85/25 grade and two parts of heated sand as in plinth protection complete all as specified

M&L for machine pressed precast concrete interlocking paver block any shape and size with grey cement and pigment confirming to IS 15658-2006 of 80 mm thickness M-40 Grade complete all as specified and directed

Material & Labour for Chequered cement concrete tiles 20cm x 20cm x 25mm thick over 20cm thick cement screed bed in CM 1:6, set, jointed and pointed in neat cement slurry in floors, complete all as specified and directed.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed.

Material & Labour for preparation of new surfaces of plastered walls and applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over and including a coat of 1.5 mm thick white wall care putty (premium quality) over plastered surfaces of walls to prepare the surface even and smooth complete all as specified . .

M&L Preparation of newly plastered surfaces of wall to achieve a level and smooth to wall, preparing wall with putty to a uniform smooth surface, and aapplying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces. on external surface as directed by Engineer-in-charge

M&L Preparation of new plastered surfaces and applying with three coat of white wash on wall surfaces complete all as specified and as directed.

Complete removal of existing treatment and applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over and including a coat of 1.5 mm thick white wall care putty (premium quality) over plastered surfaces of walls to prepare the surface even and smooth complete all as specified.

Material & Labour for complete removal of existing treatment, preparation of surfaces of plastered walls and applying Two coats of Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. over and including a coat of primer and 1.0 mm thick white wall care putty (premium quality) over plastered surfaces of walls to prepare the surface even and smooth complete all as specified . .

S&F Sheet glass 4.8 mm thick, ordinary quality & glazing with oil putty in square but n.exc 0.5 sq.m in each pane complete all as specified and as directed.

S&F 4mm thick figured glass, pin head type and glazing with oil putty or with brass screws in square n. exc 0.5 sqm in each pan for bathrooms/toilets ventilators all as directed

S&F Sheet glass 4 mm thick, ordinary quality & glazing with oil putty in square but n.exc 0.5 sq.m in each pane complete all as specified and as directed.

M & L for preparation of new surface of wood and wood based surfaces by knotting, stopping etc of any description exc 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M & L for preparation of Old surface of wood and wood based surfaces by knotting, stopping etc of any description exc 10 cm width or girth and applying one coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L & preparation of new steel surfaces and applying two coats of synthetic enamel paint over a coat of red oxide primer of any description not otherwise described over 10 cm width or girth, complete all as specified and directed.

M&L & preparation of Old steel surfaces and applying one coats of synthetic enamel paint of any description not otherwise described over 10 cm width or girth, complete all as specified and directed.

S&F in repair angle cock 15 mm bore fancy type chromium plated, with capstan head, high pressure, screwed down, screwed for iron pipe or for brass ferrule fixed to iron pipe complete all as specified and as directed.

S&F in repair 15mm bore pillar taps cast copper alloy,with capstan heads,chromium plated,screwed down, fancy type high pressure, with or without lettred 'HOT orCOLD' with long screwed sunk and fly nuts complete all as specified and directed.

S&F in repair CP Bib taps 15mm dia, with cfancy handle, screwed down, screwed for iron pipe or for brass ferrule, fency type and fixed complete all as specified and directed.

S&F in repair Stop valve cast copper alloy screwed down high pressure with capston headed handle chromium plated concealed type screwed both ends for pipe 15 mm bore or for unions complete all as specified and as directed.

S&F in repair stainless steel kitchen plate rack(24''x24''x10'') including necessary fixing/fitting & making good the existing surface complete all as specified and directed .

S&F in repairs Door seal (Snake guard) with Aluminium frame powder coated complete all specified and directed

S&F in repair soap dish CP, any type fixed to plugs chromium plated brass screws complete all as specified and as directed.

S&F in repair corner glass shelf (medium) 225 x 225 mm all as specified and as directed.

S&F in repair glass self assembly consisting of 5.5 mm thick glass sheet glass self 12 Cm wide with CP bracket gaurd and railing 60 Cm long complete all as specified and as directed.

S&F in repair chromiuim plated Swivel shower roses with shower arm, 125 mm size including fxing to steel pipe or union etc complete all as specified and as directed.

S & F in repairs vitreous china squatting pan, 'Orissa" pattern, size 580 mm X 440 mm white with ‘P’ or ‘S” trap, front or back inlet and integral foot rests, any pattern and including fixing , connector to flush pipe, lime concrete bedding and making connections to flush pipe, connector to branch pipe and anti syphonage pipes etc. including sealing the joints and making leak proof using sealant complete all as specified and as directed by Engineer-in-Charge.

S&F in repairs PVC valveless,syphonic action type dual flush, low level PVC flushing cistren 10 ltr cap white with flush pipe & all fitting complete all as specified.

Supply only flush pipe of polyethylene of low or high density of PVC, 32 mm dia, for low level cistern.

Supply & Fixing in repairs Vitreous China Ware Wash hand basin white flat back size 550mmx400mm without pedestal, cutting for and pinning ends of brackets or erecting stand including necessary PVC outlet pipe, CP coupling 32mm dia complete all as specified complete all as specified

S&F PVC connections 15 mm size with PTMT nuts of length 600mm complete all as specified and as directed.

S&F in repairs kitchen sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes, coupling including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915mmx460mm bowl size 410 mmx330mmx 160mm etc complete all as specified and as directed.

S&F in repairs grating square, Grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40gms), complete all as specified and directed.

M&L for steel tubes,15mm dia bore 'medium grade' with all fitting; laid in wall and ceiling complete all as specified and directed.

M&L for steel tubes,20mm dia bore 'medium grade' with all fitting; laid in wall and ceiling complete all as specified and directed.

S&F in repairTubular towel rail, 20mm dia, D type, brass chromium plated, 60cm long between flanges complete all as specified and directed.

S&F in repairs SS Curtain rod of 25mm dia of PVC coated in curtain rod, complete all as specified and directed.

S&F in repairs SS bracket size 150mm made to shape suitable for holding curtain/drapery rod of 25mm dia fixed with SS rail plugs and SS steel screws for single/double rods, complete all as specified and directed.

S&F in repairs110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall/laid in floor complete all as specified and as directed.

S&F 110mm bore PVC (SWR) bends any radius complete all as specified and as directed.

M&L Cement concrete 1:3:6, type C-1(using 20mm graded crushed stone aggregate) in surface channels and drains and Manholes complete all as specified and directed.

Taking down carefully point wiring for one light, socket or power etc incl all fittings such as switches sockets, holders, light fittings, fan requlators etc and making good the disturbed surface of wall, ceiling etc including seperating serviceabel light fittings, switches etc and keeping in safe custody for reuse and removal of unserviceable materials from site complete all as specified and directed.

M & L for concealed point wiring for fan/light point controlled by one one way switch complete with 1.5 sq mm FRLSH,PVC insulated multi stranded copper conductor single core cable 1100 volts grade (Red/yellow/blue wires for phases and black wire for neutral),drawn into and including non metalic PVC rigid conduit medium grade of suitable size and conduit accessories fixed on wall, floor, roof etc. and including PVC FRLSH insulated 1.5 sq mm copper conductor for earth continuity (Green Colour) and connected to common earth dolly including sunken in GI terminal box 2.8 mm thick bakelite hylam sheet cover, ISI marked with CM/L no. for mounting switch & sockets ect. Note : a) Note :- Cost of PVC conduit, cutting chases of wal/ceilingl, making good disturbed wall surfaces including finishing with cement mortor 1:4, matching with existing colour/paint of surface are deemed to be included in the quoted rate.

All as per item No 122.00 here-in-before but for one 6 pin multi purpose 5/6 Amps socket outlet on the same board with other switches.

All as per item No.122.00 here-in-before but 5 Amp Calling bell point with other switches.

All as per BOQ item No 122.00 here-in-before but for one power pointt using by 2.50 sq mm FRLSH,PVC insulated multi stranded copper conductor single core cable 1100 volts grade (Red Colour use for Phase & Black Colour use for Neutral), and with and including FRLSH,PVC insulated multi stranded copper conductor single core 2.50 sq mm conductor for earth continuity (Green Colour) , on independent board ( but Not below the switch board of light points in the same vertical plane).

All as per BOQ item No 122.00 here-in-before but for one power pointt using by 4.00 sq mm FRLSH,PVC insulated multi stranded copper conductor single core cable 1100 volts grade (Red Colour use for Phase & Black Colour use for Neutral), and with and including FRLSH,PVC insulated multi stranded copper conductor single core 4.00 sq mm conductor for earth continuity (Green Colour) , on independent board ( but Not below the switch board of light points in the same vertical plane).

Material & Labour for point wiring complete with 1.5 sq mm FRLSH, PVC insulated multi stranded copper conductor single core cable 1100 volts grade (Red Colour use for Phase & Black Colour use for Neutral),drawn into and including PVC casing- caping (double interlock type) of not less than 20mm width with accessories and fittings such as bends, elbows, tees, crosses, junction box etc, fixed on wall/ceiling with GI saddles, GI screws, rawl plugs etc. for one light/fan/ bell point controlled by one switch including pressed steel terminal box powder coated of suitable size with 3 mm thick plastic laminated sheet cover of approved make for housing/mounting switches, sockets & regulators etc. and drawing 1.5 sq. mm copper solid conductor PVC insulated, unsheated cable as earth continuity conductor, connected to common earth and earth dolly , all as specified and directed by Engineer-in-Charge Note :- Cost of PVC casing & capping, making good disturbed wall surfaces including finishing with cement mortor 1:4, matching with existing colour/paint of surface are deemed to be included in the quoted rate.

All as per BOQ item No 127.00 here-in-before but for one power pointt using by 2.50 sq mm FRLSH,PVC insulated multi stranded copper conductor single core cable 1100 volts grade (Red Colour use for Phase & Black Colour use for Neutral), and with and including FRLSH,PVC insulated multi stranded copper conductor single core 2.50 sq mm conductor for earth continuity (Green Colour) , on independent board ( but Not below the switch board of light points in the same vertical plane).

Supply and fixed switch piano flush type, single pole , 5/6 Amps, one way complete all as specified and directed By EIC.

Supply and fixed Bell switch piano flush type, single pole , 5/6 Amps, one way complete all as specified and directed By EIC.

Supply and fixed switch piano flush type, single pole , 16 Amps, one way complete all as specified and directed By EIC.

Supply and fixed socket outlet 2 in 1 multipurpose 5 pin , (6 Amps ) flush type controlled by one switch duly marked complete all as specified and directed By EIC.

Supply and fixed switch socket combination 2 in 1 multipurpose 5 pin , (6 Amps ) flush type controlled by one switch complete all as specified.

Supply and fixed switch socket combination 3 pin , (16 Amps ) flush type controlled by one switch complete all as specified.

Supply & fixed Bell multi music type, AC 230 Volts, single pole 230 volts all as specified and directed.

Supply & fixed ceiling rose surface bakelite 45 mm x 50 mm two to three terminal suitable for 230 Volts AC 6 Amps complete all as specified by EIC.

Supply & fixed stepped type electronic fan regulator flush type 240 Volts ISI marked complete all as specified By EIC.

Supply & fixed lamp holder, polycarbonate body with back plate straight or angular suitable for batten fittings complete all as specified.

S&F wall mounted fans complete with blades, in built regulator and accessories, 230 V, 300 mm sweep. Min air delivery 50 CFM, 90 degree oscillation and colour white complete all as specified and directed

S&F wall mounted fans complete with blades, in built regulator and accessories, 230 V, 400 mm sweep. Min air delivery 50 CFM, 90 degree oscillation and colour white complete all as specified and directed

S&F exhaust ventilation fan with louvers of sweep 200mm 230 volts 1200 Rpm, with blade and frame and loures sturdy engineering plastic complete with ,ISI marked complete all as directed by Engr-in-Charge.

S&F exhaust ventilation fan with louvers of sweep 250mm 230 volts 1200 Rpm, with blade and frame and loures sturdy engineering plastic complete with ,ISI marked complete all as directed by Engr-in-Charge.

Supply & fixing metalic exhaust fan with louver shutter, 300 mm sweep size or dia., 900 RPM, suitable for operation on 240 volts, AC, 50 Hz, single phase electric supply with necessary bolts (6 inches long, 6 mm dia.) with nuts and washers for fixing the fan grouted in wall including making necessary electric connection from ceiling rose to the fan with PVC insulated flexible cord copper of size 0.75 sqmm complete all as specified and directed.

S&F ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed.

Supply and fixing for concealed type sub main wiring with two run of 4.00 Sqmm single core PVC FRLSH PVC insulated unsheathed stranded copper conductor (Red/yellow/blue wires for phases and black wire for neutral) drawn in and including through Rigid non-metallic PVC conduit(medium) ISI marked of size 25mm bore with all fittings like tee/Bend/Elbow/Reducer/Bell mouth/Junction / Terminal Boxes etc. and fixing accessories such as coupler, lock nuts, saddles, pipe hook etc. including one run of 4.00 Sqmm single core PVC FRLSH PVC insulated unsheathed stranded copper conductor as earth wire (green in colour) complete all as specified. Note : (i) Note : 2 runs of line conductor, one run of earth continuity conductor, one run of PVC conduit shall be measured as unit length. (ii) Cost of PVC conduit, conductors, making good disturbed wall surfaces including finishing with cement mortor 1:4, matching with existing colour/paint of surface are deemed to be included in the quoted rate.

Supply and fixing for concealed type sub main wiring with two run of 6.00 Sqmm single core PVC FRLSH PVC insulated unsheathed stranded copper conductor (Red/yellow/blue wires for phases and black wire for neutral) drawn in and including through Rigid non-metallic PVC conduit(medium) ISI marked of size 25mm bore with all fittings like tee/Bend/Elbow/Reducer/Bell mouth/Junction / Terminal Boxes etc. and fixing accessories such as coupler, lock nuts, saddles, pipe hook etc. including one run of 6.00 Sqmm single core PVC FRLSH PVC insulated unsheathed stranded copper conductor as earth wire (green in colour) complete all as specified. Note : (i) Note : 2 runs of line conductor, one run of earth continuity conductor, one run of PVC conduit shall be measured as unit length. (ii) Cost of PVC conduit, conductors, making good disturbed wall surfaces including finishing with cement mortor 1:4, matching with existing colour/paint of surface are deemed to be included in the quoted rate.

S & F in repair LED street/security lights nominal power 35 Watt, LED wattage of minimum 1 watt each and Maximum 3 watt each, operational voltage of 170 volts to 270 volts, frequency of 50 Hz, lumen efficacy of minimum 110 lumens per watt, built-in integrated electronic LED driver, output open /short circuit protection, phase to phase protection, over voltage protection, surge voltage protection upto 4 KVs, protection grade IP 66, CRI greater than 80%, CW available CCT of 5700K, power factor of minimum 0.95, pressure die-cast aluminium alloy housing with epoxy powder coated metallic silver finish after phosphochromate treatment, life span of minimum 50000 working hours including fixing at any height and including wiring using three core PVC insulated, PVC sheathed, flexible stranded copper conductor FR-LSH cables suitable for outdoor use, 1.5 sqmm as per IS 694: 2010 complete all as specified and as directed.

S&F in repairs LED 9/10 Watt tube light fitting mirror intregated type, including LED retrofit tube lamp 9/10 W , LED tube light nominal power 9/10 Watt, L LED wattage of minimum 1 watt each and Maximum 3 watt each, operational voltage of 170 volts to 270 volts, frequency of 50 Hz, , lumen efficacy of minimum 115 lumens per watt, , integrated electronic driver (SMP based constant current supply) with output short circuit protection and surge protection upto 2.5 KV, protection grade IP 20, CRI greater than 80%, bema angle of 120 clear, THD below or less than 20%, CW available CCT of 6500K, power factor of minimum 0.95 extruded aluminium LED battens life span of minimum 50000 working hours complete fitting including connecting with PVC insulated multistranded copper flexible cable 1.0 sqmm three core, and PVC round/ square box white colour x 2 Nos for mounting of fitting including taking down old unserviceable complete all as specified & directed. . Note : Make of batten and LED tube lamp should be of same make.

S&F in repairs LED 20 Watt tube light fitting intregated type, including LED retrofit tube lamp 20 W , LED tube light nominal power 20 Watt, LED wattage of minimum 1 watt each and Maximum 3 watt each, operational voltage of 170 volts to 270 volts, frequency of 50 Hz, , lumen efficacy of minimum 110 lumens per watt, , integrated electronic driver (SMP based constant current supply) with output short circuit protection and surge protection upto 2.5 KV, protection grade IP 20, CRI greater than 80%, bema angle of 120 clear, THD below or less than 20%, CW available CCT of 6500K, power factor of minimum 0.95 life span of minimum 50000 working hours and LED batten with aluminium housing and polycarbonate diffuser complete fitting including connecting with PVC insulated multistranded copper flexible cable 1.0 sqmm three core, and PVC round/ square box white colour x 2 Nos for mounting of fitting complete all as specified & directed. . Note (i) Make of batten and LED tube lamp should be of same make.

Supply and fix Decorative wall light, fixture made up of polycarbonate suitable for 9W LED lamp B22 base complete all specified and directed.

S&F sheet metal enclosure (Plug & Socket) with 20 Amp Mcb and two pin and earth plug and socket complete with one single pole MCB complete all as specified and as directed.

S & F sheet metal enclosure for MCB, DB, SPN, 240 Volts, 100 Amps rated busbar, Confirming to IS as per IEC 61439-3, 4 way Double door enclosure made up of CRCA sheet steel, RAL 9003 powder coated, IP 43 , IK 09 including fixing the DB box flush in wall of any type and making good the distrubed surface to match as the existing with all as specified and directed by Engr-in-charge.

S & F sheet metal enclosure for MCB, DB, SPN, 240 Volts, 100 Amps rated busbar, Confirming to IS as per IEC 61439-3, 8 way Double door enclosure made up of CRCA sheet steel, RAL 9003 powder coated, IP 43 , IK 09 including fixing the DB box flush in wall of any type and making good the distrubed surface to match as the existing with all as specified and directed by Engr-in-charge.

S & F in repairs sheet metal enclosure for MCB, DB, SPN, 240 Volts, 100 Amps rated busbar, Confirming to IS as per IEC 61439-3, 12 way Double door enclosure made up of CRCA sheet steel, RAL 9003 powder coated, IP 43 , IK 09 including fixing the DB box flush in wall of any type and making good the distrubed surface to match as the existing with all as specified and directed by Engr-in-charge.

Supply and fixing 240V, 10 KA 'C' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 AMP, in the MCB DB Complete with connection testing and commissioning.

Supply and fixed MCB SPN 32 Amps, 'C' series 10kA, 240 Volts and to be housed in DBs complete including necessry connection all as specified and directed. (Note :- Proper and suitable size cable lugs to be fixed with MCB are included in unit rate of each MCB of any rating)

Supply and fixed MCB SPN 40-63 Amps, 'C' series 10kA, 240 Volts and to be housed in DBs complete including necessry connection all as specified and directed. (Note :- Proper and suitable size cable lugs to be fixed with MCB are included in unit rate of each MCB of any rating)

S&F MCCB 4 pole, 3 phase, 415 volt of capacity 36-100 Amp, 16 KA complete with proper copper thimbles, copper reducer etc complete all as specified and as directed.

Taking down old ceiling fan of any capacity/sweep after disconnecting the electric supply from any site, carry out over hauling including removing dust and grease, and cleaning of internal mechanical parts of fan with kerosene oil, checking of alignment of shaft, oiling and greasing, and re-assembling including preparing Surfaces of , filling Cavities with Filler and applying One Coat DUCO Paint with Spray Machine including Writing MES No. in Black Paint, .and connecting/refixing of fans in its original position by providing new GI nut bolt, lock washer and lock/split pin complete all as specified and directed by Engr-in-charge. NOTE: (i) Replacement of rubber bush, split pin, nuts, olts, sprng washers, check nuts etc as required are deemed to be included in the item rate

Material and labour for earthing complete with Galvanised steel earth plate electrode 600x600x6 mm mm buried directly in ground (Earth pit not less than 2.25m below ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to GI wire 4 mm as earth lead by means of bolt, nuts, check nuts and washers of galvanised iron or steel, upto 7.5m length, earth strip protected by and including 15 mm dia GI pipe (light grade) and connected to main test point or body of pole/pannel or lightening arrester of main controlling switch as directed including concrete pit in PCC (1:3:6) type C1 , Precast RCC (1:2:4) Type B1 cover slab of size 54x54x5 cm reinforced with 8 mm dia TMT bars @ 100 mm C/C both ways with one handle for lifting made out of 10 mm dia TMT bar embedded in precast cover slab, funnel, wire mesh, 20 mm bore GI Pipe (Medium Grade) for watering, Charcoal and salt in alternate layers of 15 cm (Compacted Thickness) around the earth electrode including necessary excavation, earth work in any type of soil and disposal of spoil to a distance n.exc 50 m and necessary testing complete all as shown in Electrical Plate No 3 of SSR Part-I. NOTE : 1. The unit rare includes for protectionh GI pipe of 15mm and watering pipe of 20mm bore including excavation for earth pit in any type of soil/disintegrate rock. 2. Contractor has to bring agriculture soil from outside of defence land and fill in earth pit to acheive desired result as the soil resisitivity is very high. 3. The cost of GI wire including protection pipe, from top of earth plate upto 7.5 meter above/below ground level is deemed to be included in the unit rate. 4. All the joints in GI wire and connectgion with earth plate to be welded through brazing and in addition by providing double brass nut bolt and washer. 5.Costing of welding and nut bolts are deemed to be included in the unit rate

Taking down/out unserviceable UG Cables of any Cross Sectional Area and Connections including Bricks, GI Pipes, etc. of any descriptions, laid in Trenches and/or fixing with Walls/Poles including Segregating of Serviceable Materials viz Bricks, Cables, GI Pipes, etc. and keep in Safe custody for re-use, complete all as specified and as directed

Supply, Laying and testing cable LT XLPE sheathed,PVC insulated screened PVC bedded,galvanised steel strip of wire armoured electric power cable heavy duty with stranded aluminium conductor 1100 volt grade, laid in trenches/surface of wall/in GI pipe along with pole for connection to OH lines,including brass cable glands,clamps,etc of 4 core 25 sqmm.

Supply, Laying and testing cable LT XLPE sheathed,PVC insulated screened PVC bedded,galvanised steel strip of wire armoured electric power cable heavy duty with stranded aluminium conductor 1100 volt grade, laid in trenches/surface of wall/in GI pipe along with pole for connection to OH lines,including brass cable glands,clamps,etc of 2 core 16 sqmm.

Supply, Laying and testing cable LT XLPE sheathed,PVC insulated screened PVC bedded,galvanised steel strip of wire armoured electric power cable heavy duty with solid aluminium conductor 1100 volt grade, laid in trenches/surface of wall/in GI pipe along with pole for connection to OH lines,including brass cable glands,clamps,etc of 2 core 10 sqmm.

M&L Sand Cushioning (dry) in trenches for protection of UG Cables (below, above and around the UG Cable laid in Trenches) of 230mm Spread thickness and consolidated (punned) upto 180mm thickness, complete all as specified and as directed. (NOTE : For the purpose of Payment, Punned thick-ness of Sand Cushioning only shall be Measured and Paid )

Supply and laying well burnt Bricks , locally available best quality (sub class "B" bricks) laid in trenches perpandicular to U/G cable for cable protection complete all as specified.

S&F Pipes galvanized, 40 mm bore “light grade”, supplied and laid complete including necessary fittings such as tees, bends, elbows, sockets, reducers etc as per site requirement or specified.

S&F Pipes galvanized, 50 mm bore “light grade”, supplied and laid complete including necessary fittings such as tees, bends, elbows, sockets, reducers etc as per site requirement or specified.

S & F rotational moulded polyethylene ISI marked (vertical cylindrical with close top) as per IS 12701: 1996 of 1000 litres capacity hoisted and fixed in position with and including Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for 20/25mm bore dia iron pipe, provision of 20 mm /25 mm dia medium grade GI pipe for connecting inlet, outlet, over flow and washout pipes including dismantling the existing one and removing to store complete all as specified and as directed.

Supply & fix 25mm bore GI tubing medium grade in trenches / Floor / pillar connetion in old or new postion including fittings all as specified & as directed including taking down old unseviceable pipe (Make: Bansal , Jindal)

Supply & fix 40mm bore GI tubing medium grade in trenches / Floor / pillar connetion in old or new postion including fittings all as specified & as directed including taking down old unseviceable pipe (Make: Bansal , Jindal)

Supply and fix in repair 25 mm bore dia pipe gun metal globe or gate valves, yoke type, full opening with iron wheel head, screwed both ends heavy duty, ISI marked complete for iron pipes complete all as specified and directed.

Supply and fix 40 mm bore dia pipe gun metal globe or gate valves, yoke type, full opening with iron wheel head, screwed both ends heavy duty, ISI marked complete for iron pipes complete all as specified and directed.

ROY ENTERPRISE (BID ID -3482406)

Excel Enterprises (BID ID -3482219)