SPL REPAIR TO BUILDING NO. PC-65, PC-68, PC-77 AND PC-78 (04 BLOCK) AT AF STATION CARNICOBAR

Amount

Dismantling of floor, hearth or wall tlling including cement mortar bedding but not backing , removing serveceable tiles to store and rubush off the premices complete all as directed by Engineer in Charge

Distmantling of ceiling boards (fibre, pulp, insulation etc.) or insulation bords/ slab/ blankets, any thicness, including cover fillets complete all as specified and directed.

Dismantling of plain or corrugated steel sheeting any gauge or thickess as directed by Engineer in Charge.

M&L for prepanted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour havig tensile stength 550 Mpa as in roof covering fxed with self tappig GI screws / L type or J type hook all as specfied & diected by Engineer in Charge.

M&L for prepanted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour havig tensile stength 550 Mpa as in ridge for roof covering fxed with self tappig GI screws / L type or J type hook all as specfied & diected by Engineer in Charge.

M&L for ceramic tiles of light coloured of size 600x600x7-8mm mm thick as floors set and jointed in neat cement slurry and pointed in coloured cment to match colour f tiles bedded over and including 15mm thick screed bedding in cement mortar (1:6) complete all as specfied & directed by Engineer in Charge.

M&L for ceramic tiles of light coloured of size 600x600x7-8mm mm thick as vertical surface set and jointed in neat cement slurry and pointed in coloured cment to match colour f tiles bedded over and including 10mm thick screed bedding in cement mortar (1:4) complete all as specfied & directed by Engineer in Charge.

S&F anodised aluminium snap grid frame (with minimum 15 micron uniform anodic coating) size of 605mm x 605mm consisting of Tee/Angle section, size 40 x 40 x 2mm as approved make confirming to IS-733 in frame of false ceiling including aluminium cleat with necessary CP brass/stainless steel shunk screws. Aluminium perimeter angles fixed to wall/wooden frame at centre to centre and fixing frames to level adjusting anchors 8mm dia GI wire with hook in Tee members at 1.5m centre to centre fixed to steel trussed roof complete all as specified and as directed.

M&L 4mm thick non asbestos fibre cement building boards fixed or laid/inserted to aluminium frame work with screw in ceiling . complete all as directed by Engineer in Charge.

M&L for preparation of old decorated brick/concrete plastered/un-plastered surfaces of walls pillars cornices and M&L for one coat of antifungal weather proof emulsion paint, complete all as specified and directed.

Taking down cement plaster on brick or stone walls, ceilings etc. including raking out joints, hacking for key, scrubbing down with water, etc. complete all as specified and directed.

M & L rendering 15 mm thick in cement morter 1:4 on fair faces of concrete surface even and fair finish w/o using extra cement with mixed water proffing compound complete all as specifid and directed.

M&L for roof trusses (framed) , trussed, purlins crane, gantries ,rails and fastening and heavy bracket framing (Beam ,Tee, Angle, Channel or Flat sections) including distances pieces, cleats etc.(Fe 410-W Gde-E-250 or Fe-310-0) including preparation of surface and providing one shop coat of zinc chrome primer at contractor work's shop before fabrication complete all as directed by Engineer in Charge.

S&F mild steel flat iron for wind tie etc including necessary drilling holes and fixing with necessary self drilling and self tapping screws/bolts and nuts, neoprene and limpet washers with 150mm end laps wherever required complete all as specified and directed.

Material and labour for preparation of old painted steel surfaces of exceeding 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M/L preparing old decorated surface of walls, including brooming down and cleaning the surface and applying one coat of distemper (oil emulsion) of any tint on walls all as directed

Dismantling of wrought iron or mild steel work of any description not otherwise provided for all as directed by Engineer in Charge

M&L for point wiring with 1.5 Sqmm PVC insulated unsheathed copper conductor multistranded 1100 volts grade single core including one single core 1.5 sqmm PVC insulated copper conductor cable as earth continuity conductor (colour green) drawn through and including PVC casing and capping with all accessories fixed to all type of electrical fittings and earth terminals/earth dolly, complete with PVC rectangular block and rawl plugs fixed to walls/ceilings/roofs/concealed with & including PVC/MS fabricated terminal boxes/modular boxes, flush/wall mounted for mounting of switches, switch socket combination, fan regulator etc with PVC sheet top cover or hylam sheet 3mm thk as specified & as directed for the following :- (a) One 5 Pin 5 Amps switch socket on independent board

Supply and fix switch socket combination 2 in 1 5 Amps flush type all as directed by Engineer-in-Charge

Supply and fix wall mounting fan 400mm sweep high speed with three steep speed variation including mounting assembly all as directed. Make : Platina HS of Havells

kakolil trade agencies

RS ENGINEERING WORK

M/s Kanaka Agencies

M/s Pintu Furniture

S K ENTERPRISES

KML CONSTRUCTION

KARMAKAR CONSTRUCTION