ADDITION ALTERATION OF BOUNDARY WALL IN TECHNICAL AREA OF ICGAS DAMAN

Amount

Demolition of brick work built in cement mortar incl all quoins, arches, pillars, etc complete all as specified and directed.

Demolition of Concrete of any description and in any position not otherwise specifically provided for, if cement concrete is reinforced (reinforcement cut as required to facilitate demolition) complete all as specified and as directed including removal of debrises exc 50m not exc 1.50km

Dismantling of old barbed wire and making rolls including stacking neatly complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for angle iron or flat iron as in post and guard bar or grating complete all as specified and directed.

M&L for Cement concrete 1:4:8 type D-2 using 40 mm graded stone aggregate as in foundation filling and mass concrete all as specified and directed.

M&L for Reinforced Cement concrete M-30 (design mix) using 20 mm graded stone aggregate as in foundation including raft, foundation beam plinth beam and mass concrete all as specified and directed.

M&L for Reinforced Cement concrete M-30 (design mix) using 20 mm graded stone agg as in beam, cantilever, top bands like etc lintels over 1.5 M span all as specified and directed.

M&L for Reinforced Cement concrete M-30 (design Mix) using 20 mm graded stone agg as in columns, pillers, piers posts and strut complete all as specified and directed.

M&L for form work to sides of concrete foundations, footing, bases of columns, raft and raft beam, sides and soffits of foundation and plinth beam and similar work for rough finished surfaceall as specified and directed.

M&L for form work to sides of pillers, posts, piers, columns square, rectangular or polygonal for rough finished surface of concrete all as specified and directed.

M&L for form work to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n. exc 20cm wide and sides of RCC/PCC bands in walls, horizontalor sloping and similar work exc 10cm but n. exc 20cm wideall as specified and directed.

M&L for TMT bars 10 mm dia (Fe-500D) and over cut to length bent to shape required including cranking bending spirally for hooping and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

All as item no. 12 above but 5mm dia and over upto and including 10 mm dia as in stirrups spacers and binders.

M&L for Pre-cast cement concrete block masonry with solid blocks type C1 1:3:6 using 20mm graded aggregate, exc. 10 cm in width and setting in mortar CM (1:6), complete as specified.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. complete all as specified and directed

M&L for 15 mm thick rendering on other than fair faces of concrete surface finished even and fair without using extra cement in CM 1:4 all as specified and directed.

M&L Mild steel work conforming to Fe 290 grade-E as in angle iron posts with swan neck (horn) and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire etc necessary drilling, bolting or welding/riveting etc all as specified and directed.

S&F Galvanised, 2 strand, steel barbed wire 2.24 mm dia, barbed with 2mm dia, barbs at 75mm spacking as in fencing and straining and fixing to any type of standard rails/ straining bolts including securing or tying at crossing with and provision of galvanised mild steel wire, staples or steel pins etc complete as specified and directed (each line of wire to be measured separately).

M&L for Prepartion of newly plastered surface of wall and applying two coat of cement base paint over a coat of white washall as specified and directed.

M&L for Preparation of new steel and iron surfaces of any description over 10 cm in width or girth, priming with a coat of red oxide primer and applying two coats of synthetic enamel paintall as specified and directed.

M&L for Preparation of surfaces of any description wood/steel, iron etc exc 10cm in width or girth and applying one coat of black bituminous paint on embedded steel post portion all as specified and directed.

S & F Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, spring core wire (2.5 mm thick)of high tensile strength of165kg/sq. mm with tape (0.52mm thick) and weight 43.478 gm/metre and fixing the same with existing Y-shape angle iron placed 2m apart and with 6 horizontal R.B.T. (Reinforced Barbed Tape)wire, stud tied with G.I.staple sand G.I.clips to retain horizontal, including necessary bolts, all complete incl taking down old coil as per direction of Engineer-incharge. Note-1) Total height of boundary wall including concertina coil fencing will be about 10ft from ground level(higher of level on both sides).

M & L Broken glass coping on top of brick masnory walls rendered with 25mm layer of cement mortar (1:3) with a rounded or weathered finish and setting broken glass (of bottle or thick glass) broken to approximately 63mm gauge, by firmly embedding at the rate of 10 Kg of glass per square metre of rendered surface, jogged edges of the glass being left projecting all as specified and directed.

Demoloition stone/ boulder masonry, built in lime mortar including all quoins, arches, pillars, etc, including ashlar facings, dressed stonework and precast concrete articles etc complete all as specified and directed .

M&L for Boulder pitching, laid dry, hand packed tightly and grouted with cement and sand mortar 1:6 in complete all as specified and dirceted .

M&L for Boulder pitching, laid dry, hand packed tightly and grouted with cement and sand mortar 1:6 in complete all as specified and directed (Note: Old stone slabs obtained from dismantling shall be reused after proper cleaning).

M&L for Complete removal of existing finished surfaces of walls and applying two coats of cement base paint over a coat of primer all as specified and directed

EXTERNAL ELECTRIC SUPPY Taking down existing street light fitting 1X36watt fitttings including angle iron rod, connecting cable of any type/make complete all as specified and directed .

Taking down old existing cables of any type/ size from the wall/ surface all as specified and directed.

Taking down old existing light bracket, MCB, Junction Boxes of any type/ size from the wall surface all as specified and directed.

Taking down old unserviceable feeder pillar boxes by disconnecting all cable connections and dismantling from site all as specified and directed.

Taking down old unserviceable LT panel (outdoor type) by disconnecting all cable connections and dismantling from site all as specified and directed.

Supply and fix LED street light 35/36 W 230 V AC outdoor type with high pressure die cast aluminium housing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed.

Supply and fix FRP looping box with 3 phase connector and comprising of MCB SP 6 amps, 240 volts complete with and including providing GI bracket, clamps, nuts, bolts etc suitable for fixing on PCC pole/ wall etc complete all as specified and directed.

Supply, laying and testing cable XLPE insulted, screened, PVC bedded, galvanised steel strip or armoured electric power cables, (heavy duty) 1100 volts grade with stranded aluminium conductor of size 16 sqmm, 4 core laid in trenches, pipe/ducts/walls and making cable connections by providing cable lugs and gland including removing old unserviceable cable, lugs, glands etc complete all as specified and directed.

M & L wiring connection from junction box to street light fitting with 3 core 1.5 sqmm PVC insulated Sheathed aluminimum stranded conductor 1100 Volt all as specified and directed.

Supply,install testing and commissioning of outdoor type feeder pillar box of suitable size cubicle type floor mounted made with 3.15 mm thick powder coated factory fabricated CRCA sheet, IP 54 class of protection, with alluminium bus bar size 100 amps for phase and neutral of suitable size etc complete all as specified and directed comprising the following:- (a) Time switches 415 V three phase of 20 Amp with contector (b) MCB TPN 16 Amps, 415V, 50Hz 10KA (c) Phase indicating lamp R-Y-B

Supply, installation,testing and commissioning LT panel board of suitable for working on 3 phase, 4 wire, 415 volts, AC, 50 HZ, outdoor type, cubicle, floor mounted, free standing, dust and vermin proof, air ventilation with IP-54 protection made out of 3.15 mm thick CRCA sheet and suitable sized angle iron and flats and duly powder coated paint and shall be CPRI approved, compartmentalised with rubber gasket hinged door. Panel shall have front and rear opening, locking arrangement, cable alleys, bus bar chamber and switch gear compartment, bottom cable entry holes for incoming and outgoing cables, earthing terminals, affixing danger notice plate, each compartment shall be numbered/lettered for indication, Aluminium bus bar duly covered with heat shrinkable sleeves colour coaded duly fixed on DMC/SMC insulators housed in a separate bus bar chamber and control wiring with copper conductor cables of adequate size and length, incoming and outgoing MCCB's shall have extended bus bar links and civil work/PCC foundation as per site requirement complete all as specified and directed comprising of following:- Main LT Panel No 1) (i) MCCB 100Amps, 4P, 25KA,415 volts,50Hz-01 Nos (I/C) (ii) MCCB 63Amps,4P,16 KA,415 volts,50Hz-1 Nos (O/G) (iii) MCCB 32 Amps,4P,16 KA, 415 volts,50Hz-1Nos (O/G) (iv) MCB 16 Amps,4P,415 volts,50Hz-1Nos (O/G) (v) Digital Multifunctional meter (as Volt meter, Ampers meter, frequency meter) including CT`s, setector switch etc- 01 Nos (v) LED phase indication lamps RYB - 1 Set. (vi) Aluminium bus bar TPN 150 Amps capacity - 1 set

Supply, installation,testing and commissioning LT panel board of suitable for working on 3 phase, 4 wire, 415 volts, AC, 50 HZ, outdoor type, cubicle, floor mounted, free standing, dust and vermin proof, air ventilation with IP-54 protection made out of 3.15 mm thick CRCA sheet and suitable sized angle iron and flats and duly powder coated paint and shall be CPRI approved, compartmentalised with rubber gasket hinged door. Panel shall have front and rear opening, locking arrangement, cable alleys, bus bar chamber and switch gear compartment, bottom cable entry holes for incoming and outgoing cables, earthing terminals, affixing danger notice plate, each compartment shall be numbered/lettered for indication, Aluminium bus bar duly covered with heat shrinkable sleeves colour coaded duly fixed on DMC/SMC insulators housed in a separate bus bar chamber and control wiring with copper conductor cables of adequate size and length, incoming and outgoing MCCB's shall have extended bus bar links and civil work/PCC foundation as per site requirement complete all as specified and directed comprising of following:- (Main LT Panel No 2 ) (i) MCCB 63Amps, 4P, 25KA,415 volts,50Hz-01 Nos (I/C) (ii) MCB 32Amps,4P,415 volts,50Hz-1 Nos (O/G) (iii) MCB 16 Amps,4P,415 volts,50Hz-1Nos (O/G) (iv) Digital Multifunctional meter (as Volt meter, Ampers meter, frequency meter) including CT`s, setector switch etc- 01 Nos (v) LED phase indication lamps RYB - 1 Set. (vi) Aluminium bus bar TPN 100 Amps capacity - 1 set

Supply, installation,testing and commissioning LT panel board of suitable for working on 3 phase, 4 wire, 415 volts, AC, 50 HZ, outdoor type, cubicle, floor mounted, free standing, dust and vermin proof, air ventilation with IP-54 protection made out of 3.15 mm thick CRCA sheet and suitable sized angle iron and flats and duly powder coated paint and shall be CPRI approved, compartmentalised with rubber gasket hinged door. Panel shall have front and rear opening, locking arrangement, cable alleys, bus bar chamber and switch gear compartment, bottom cable entry holes for incoming and outgoing cables, earthing terminals, affixing danger notice plate, each compartment shall be numbered/lettered for indication, Aluminium bus bar duly covered with heat shrinkable sleeves colour coaded duly fixed on DMC/SMC insulators housed in a separate bus bar chamber and control wiring with copper conductor cables of adequate size and length, incoming and outgoing MCCB's shall have extended bus bar links and civil work/PCC foundation as per site requirement complete all as specified and directed comprising of following:- (Main LT Panel No 3) (i) MCCB 63Amps, 4P, 25KA,415 volts,50Hz-01 Nos (I/C) (ii) MCCB 32 Amps,4P,16 KA, 415 volts,50Hz-1Nos (O/G) (iii) MCB 32Amps,4P,415 volts,50Hz-1 Nos (O/G) (iv) MCB 16 Amps,4P,415 volts,50Hz-1Nos (O/G) iv) Digital Multifunctional meter (as Volt meter, Ampers meter, frequency meter) including CT`s, setector switch etc- 01 Nos (vi) LED phase indication lamps RYB - 1 Set. (vii) Aluminium bus bar TPN 100 Amps capacity - 1 set

M & L Earthing complete with Galvanized steel earth plate electrode of size 600mmX600mm, 6.00 mm thick buried directly in ground vertically to a depth not less than 2.25 metres below the normal ground level with top edge of the plate not less than 1.5m below normal GL and connected to galvanized iron strip of size 32 x 6 mm size by means of bolts, nuts, check nuts and washers of galvanized iron steel all as shown in Electrical Plate No.3 connecting to earthing test point, including necessary earth work in any type of soil, PCC earth chamber made in PCC 1:3:6 type C1 (using 20mm graded aggregate), common salt, charcoal, CI funnel, earth pit cover in RCC 1:2:4 type B1 (using 20mm graded aggregates), with 8mm CTD bars @ 100mm c/c in both ways, including necessary form work complete including necessry test on completion all as specified and as directed. Note : The unit rate shall also include for excavation, earth work in hard/dense soil PCC (1:3:6) type C1 pit, RCC cover slab, GI funnel with 40 mm dia watering pipe, wire mesh, 15mm dia light grade GI protection pipe for earth lead etc., complete.

M & L Earthing complete with Galvanized steel earth plate electrode of size 600mmX600mm, 6.00 mm thick buried directly in ground vertically to a depth not less than 2.25 metres below the normal ground level with top edge of the plate not less than 1.5m below normal GL and connected to galvanized iron wire of 4mm size by means of bolts, nuts, check nuts and washers of galvanized iron steel all as shown in Electrical Plate No.3 connecting to earthing test point, including necessary earth work in any type of soil, PCC earth chamber made in PCC 1:3:6 type C1 (using 20mm graded aggregate), common salt, charcoal, CI funnel, earth pit cover in RCC 1:2:4 type B1 (using 20mm graded aggregates), with 8mm CTD bars @ 100mm c/c in both ways, including necessary form work complete including necessry test on completion all as specified and as directed. Note : The unit rate shall also include for excavation, earth work in hard/dense soil PCC (1:3:6) type C1 pit, RCC cover slab, GI funnel with 20 mm dia watering pipe, wire mesh, 15mm dia light grade GI protection pipe for earth lead etc., complete.

Excavation in trenches not exceeding 1.5 mtrs. wide and not exceeding 1.5 Mtrs. in depth in trenches and getting out in soft/ loss soil complete all as specified and directed.

Removing the excavation soil to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and directed.

Returning, filling in including spreading and levelling watering and well ramming in layers not exceeding 25 cm with soil obtain from excavation.

Supply and filling in and spreading unwashed river sand for cushioning and covering the under ground cables in trenches upto 23 cm and punning to 18 cm to provide required cover complete all as specified in SSR Part-I and as directed. Note: Punned thickess i.e 18 cm shall be measured for payment purpose.

Supplying and laying un-reinforced precast concrete cable cover, class LV, type 1, flat, size 250 x 150 x 40 mm, complete all as specified and directed.

Supply and laying GI Pipe of size 40mm light grade with all fittings in road crossing/drain etc, all as specified and directed.

SHELDON CONSTRUCTION

M/s Shree Construction Co

S G Enterprises

M/S V C SHETH